| submitted | available | document details (if available) | source link |
|---|---|---|---|
| various | 15 UserManual | Users Manual | 426.05 KiB |
Leica CTR35 User Manual Version 1.0 English Introduction Purchase Congratulations on the purchase of a Leica CTR35. This manual contains important safety directions as well as instructions for setting up the product and operating it. Refer to "1 Safety Directions" for further information. Read carefully through the User Manual before you switch on the product. Product Identifica-
tion The model and serial number of your product are indicated on the type plate. Always refer to this information when you need to contact your agency or Leica Geosystems authorised service workshop. Symbols The symbols used in this manual have the following meanings:
Type DANGER WARNING CAUTION NOTICE Description Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor or moderate injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in appreciable material, financial and environmental damage. Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. CTR35, Introduction 2 Table of Contents In this manual Chapter 1 2 3 4 5 6 7 Safety Directions 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Description of the System General Introduction Definition of Use Limits of Use Responsibilities Hazards of Use Electromagnetic Compatibility EMC FCC Statement, Applicable in U.S. IC Statement, Applicable in Canada. Operation Configuration Troubleshooting Transport Storage Cleaning and Drying Care and Transport 6.1 6.2 6.3 Technical Data 7.1 7.2 CTR35 Technical Data Conformity to National Regulations Page 4 4 4 4 5 5 6 7 7 8 9 10 13 14 14 14 14 15 15 16 CTR35, Table of Contents 3 1 1.1 Safety Directions General Introduction Description The following directions enable the person responsible for the product, and the person who actually uses the equipment, to anticipate and avoid operational hazards. The person responsible for the product must ensure that all users understand these directions and adhere to them. 1.2 Definition of Use Intended use
Remote control of product.
Data communication with external appliances. Reasonably fore-
seeable misuse
Use of the product without instruction.
Use outside of the intended use and limits.
Disabling safety systems.
Removal of hazard notices.
Opening the product using tools, for example screwdriver, unless this is permitted for certain functions.
Modification or conversion of the product.
Use after misappropriation.
Use of products with obvious damages or defects.
Use with accessories from other manufacturers without the prior explicit approval of Leica Geosystems. Inadequate safeguards at the working site.
1.3 Limits of Use Environment DANGER Suitable for use in an atmosphere appropriate for permanent human habitation: not suitable for use in aggressive or explosive environments. Local safety authorities and safety experts must be contacted before working in hazardous areas, or close to electrical installations or similar situations by the person in charge of the product. CTR35, Safety Directions 4 1.4 Responsibilities Manufacturer of the product Leica Geosystems AG, CH-9435 Heerbrugg, hereinafter referred to as Leica Geosys-
tems, is responsible for supplying the product, including the user manual and original accessories, in a safe condition. Person responsible for the product 1.5 WARNING CAUTION WARNING The person responsible for the product has the following duties:
To understand the safety instructions on the product and the instructions in the
To ensure that it is used in accordance with the instructions.
To be familiar with local regulations relating to safety and accident prevention.
To inform Leica Geosystems immediately if the product and the application user manual. becomes unsafe.
To ensure that the national laws, regulations and conditions for the operation of e.g. radio transmitters or lasers are respected. Hazards of Use Inadequate securing of the working site can lead to dangerous situations, for example in traffic, on building sites and at industrial installations. Precautions:
Always ensure that the working site is adequately secured. Adhere to the regulations governing safety, accident prevention and road traffic. If the accessories used with the product are not properly secured and the product is subjected to mechanical shock, for example blows or falling, the product may be damaged or people can sustain injury. Precautions:
When setting-up the product, make sure that the accessories are correctly adapted, fitted, secured, and locked in position. Avoid subjecting the product to mechanical stress. If the product is improperly disposed of, the following can happen:
If polymer parts are burnt, poisonous gases are produced which may impair health.
By disposing of the product irresponsibly you may enable unauthorised persons to use it in contravention of the regulations, exposing themselves and third parties to the risk of severe injury and rendering the environment liable to contamination. Precautions:
The product must not be disposed with household waste. Dispose of the product appropriately in accordance with the national regulations in force in your country. Always prevent access to the product by unauthorised personnel. Product-specific treatment and waste management information can be downloaded from the Leica Geosystems home page at http://www.leica-
geosystems.com/treatment or received from your Leica Geosystems distributor. CTR35, Safety Directions 5 1.6 Description WARNING CAUTION CAUTION CAUTION WARNING Electromagnetic Compatibility EMC The term Electromagnetic Compatibility is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electro-
static discharges are present, and without causing electromagnetic disturbances to other equipment. Electromagnetic radiation can cause disturbances in other equipment. Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that other equipment may be disturbed. There is a risk that disturbances may be caused in other equipment if the product is used with accessories from other manufacturers, for example field computers, personal computers or other electronic equipment, non-standard cables or external batteries. Precautions:
Use only the equipment and accessories recommended by Leica Geosystems. When combined with the product, they meet the strict requirements stipulated by the guide-
lines and standards. When using computers or other electronic equipment, pay atten-
tion to the information about electromagnetic compatibility provided by the manufac-
turer. Disturbances caused by electromagnetic radiation can result in erroneous measure-
ments. Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that the product may be disturbed by intense electromagnetic radiation, for example, near radio transmitters, two-way radios or diesel generators. Precautions:
Check the plausibility of results obtained under these conditions. If the product is operated with connecting cables attached at only one of their two ends, for example external supply cables, interface cables, the permitted level of elec-
tromagnetic radiation may be exceeded and the correct functioning of other products may be impaired. Precautions:
While the product is in use, connecting cables, for example product to external battery, product to computer, must be connected at both ends. Electromagnetic fields can cause disturbances in other equipment, in installations, in medical devices, for example pacemakers or hearing aids and in aircraft. It can also affect humans and animals. Precautions:
Although the product meets the strict regulations and standards which are in force in this respect, Leica Geosystems cannot completely exclude the possibility that other equipment can be disturbed or that humans or animals can be affected.
Do not operate the product with radio or digital cellular phone devices in the vicinity of filling stations or chemical installations, or in other areas where an explosion hazard exists.
Do not operate the product with radio or digital cellular phone devices near to medical equipment.
Do not operate the product with radio or digital cellular phone devices in aircraft. CTR35, Safety Directions 6 1.7 WARNING WARNING Labelling CTR35 FCC Statement, Applicable in U.S. Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and the receiver. receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Model: CTR35 S/N: XXXXX Art. No. : 844474 5V nominal / 0.5A max Leica Geosystems AG CH-9435 Heerbrugg Manufactured: YYYY Made in Germany FCC ID: RFD-CTR35 IC: 3177A-CTR35 1.8 WARNING Canada Compliance Statement Canada Dclaration de Conformit 012084_001 IC Statement, Applicable in Canada This Class (B) digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe (B) est conforme la norme NMB-003 du Canada. This device complies with Industry Canadas licence-exempt RSS 247. Operation is subject to the following two conditions:
1) This device may not cause interference; and 2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR 247 dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1) lappareil ne doit pas produire de brouillage;
2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. CTR35, Safety Directions 7 2 General Diagram CTR35 Description of the System Technology The CTR35 is a radio device having a long-range radio module. It can be used on Leica CS35 tablets only to extend the radio range. The CTR35 is intended to be connected to the following radio devices:
RH16/RH17
TCPS29/TCPS30 Frequency The CTR35 operates in the "2.4 GHz radio band". Using the latest in spread-spectrum, frequency hopping technology, ensures maximum security for the high speed, wireless transfer of data and video. e 012079_001 a b c d a) Cover b) USB 2.0 port c) Housing d) LED e) Latch Physical features Housing The robust housing with the sealing attached to the CS35 meets the IP54 standards. It provides a high level of protection against environmental influences such as rain and dust. USB Port USB 2.0 interface for power and communications. The CTR35 is only intended to be used with the top USB port of a CS35 tablet. Description of the LED indicator LED Status LED off Flashing blue, several seconds on and then off again Permanently blue Definition The CTR35 is not powered. The CTR35 is searching for connection. The CTR35 is connected and transferring data. Depending on the data transmission rate, the LED is continuously on or flashing blue. CTR35, Description of the System 8 3 Operation Standard setup with CTR35 on CS35 Standard setup at the CS35 for remote surveying using the CTR35. The CTR35 can be connected to the following radio devices:
RH16/RH17
TCPS29/TCPS30 These radio devices can be attached to the following instruments:
MS60/TS60/TS16
MS50/TS50/TM50/TS15
TS30/TM30/TPS1200+
012075_001 Pairing of the CTR35 The pairing is done from the CS35 with the steps described in the following chapter, refer to Configuration. CTR35, Operation 9 4 Configuration Requirements for the correct configu-
ration of the CS35 Mount the CTR35 to the CS35 How to figure out the correct configu-
ration procedure
Leica Captivate version 2.0 or higher
The configuration process as described below only needs to be done once. The CTR35 has to be mounted to the CS35 as follows for a robust fixing:
Step 1. 2. 3. 4. Description Open the door of the top USB port on the CS35 completely. Hold down the opened door of the CS35. Insert the CTR35 with the USB plug into the top USB port of the CS35 as far as possible. Release the door of the CS35. Take care that the CTR35 properly snaps in. The seal of the door must sit on the latch of the CTR35. The correct configuration procedure for the CTR35 is dependent on the Leica Captivate version running on the CS35 tablet:
Step 1. 2. 3. 4. 5. 6. Description Start the CS35. Start File Explorer. Go to the root of the C: drive. Double tap on the file called lgs Version. Notepad opens the text file. Note the Leica Captivate version and the release date. Close Notepad. If the release date of Leica Captivate is before 2016-02-09 then execute all following procedures:
Procedure 1, refer to Install the driver of the CTR35 on the CS35.
Procedure 2, refer to Set the COM Port on the CS35.
Procedure 3, refer to Run the executable file on the CS35.
Procedure 4, refer to Configure the CTR35 with Leica Captivate on the CS35. If the release date of Leica Captivate is 2016-02-09 or newer then only execute the following two procedures:
Procedure 2, refer to Set the COM Port on the CS35.
Procedure 4, refer to Configure the CTR35 with Leica Captivate on the CS35. CTR35, Configuration 10 Install the driver of the CTR35 on the CS35 Step 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Description Download the CTR35 driver from myWorld. It is found in the folder Controller\CS35\Tools. Mount the CTR35 to the top USB port of the CS35, refer to Mount the CTR35 to the CS35. Open the Start screen. Tap the Control Panel tile. Choose Device Manager. Open Other devices from the tree view. Tap and hold onto CTR35. Choose Update Driver Software... from the context menu. Choose Browse my computer for driver software . Browse to the location of the driver folder. Select the folder. Press OK. Press Next. Follow the instructions until the driver is installed. It can happen that the installation has to be done several times. After the installation of the driver the Device Manager panel is still open. 15. Close the Device Manager. Set the COM Port on the CS35 Step Description Mount the CTR35 to the top USB port of the CS35, refer to Mount the CTR35 to the CS35. Open the Start screen. Tap the Control Panel tile. Choose Device Manager. Open Ports (COM & LPT) from the tree view. Tap and hold on USB Serial Port CTR35 (COMxx). Context menu is opened. Choose Properties from the context menu. Choose the Port Settings page tab. Press the Advanced button. A new panel opens up. Choose COM96 from the drop-down list of COM Port Number. Press the OK button. Return to the Device Manager. Close the Device Manager. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. CTR35, Configuration 11 Run the executable file on the CS35 Step 1. 2. 3. Description Download the executable file CTR35NetConnInstaller.exe from myWorld. It is found in the folder Controller\CS35\Tools. Run the executable file CTR35NetConnInstaller.exe either from a USB stick or from the CS35. The net configurations are installed. Close all applications. Configure the CTR35 with Leica Captivate on the CS35 A wizard guides through the Leica Captivate connection settings. The TS Connection Wizard only runs with Leica Captivate version 2.0 or higher. Step 1. 2. 3. 4. 5. 6. Description Start Leica Captivate Choose Settings. Choose Connections. Run the TS Connection Wizard. Follow instructions of the TS Connection Wizard. Close all applications. CTR35, Configuration 12 5 Troubleshooting Troubleshooting Problem CTR35 is not powered. Troubleshooting
Check, if CTR35 is properly connected to the correct USB port of the CS35.
Check status of the LED. Refer to Description of the LED indi-
cator. Leica Captivate error message: "Attach CTR35 LRBT stick" (but CTR35 is powered).
Check driver installation and COM port setting. Refer to Install the driver of the CTR35 on the CS35 and Set the COM Port on the CS35. No data transfer or no synchronisation to total station. Range is limited.
Check the Total Station type configura-
tion on the CS35.
Check, if the same Leica Captivate version is running on the CS35 and the total station.
Run executable file again. Refer to Run the executable file on the CS35.
Switch off the internal radio and Wi-Fi of the CS35. Environment of powerful transmit-
ters working within the same frequency band may cause distur-
bances. CTR35, Troubleshooting 13 6 6.1 Care and Transport Transport Transport in a road vehicle Never carry the product loose in a road vehicle, as it can be affected by shock and vibration. Always carry the product in its transport container, original packaging or equivalent and secure it. Shipping 6.2 Product When transporting the product by rail, air or sea, always use the complete original Leica Geosystems packaging, transport container and cardboard box, or its equivalent, to protect against shock and vibration. Storage Respect the temperature limits when storing the equipment, particularly in summer if the equipment is inside a vehicle. Refer to "7 Technical Data" for information about temperature limits. 6.3 Cleaning and Drying Product and acces-
sories
Use only a clean, soft, lint-free cloth for cleaning. If necessary, moisten the cloth with water or pure alcohol. Do not use other liquids; these may attack the polymer components. Damp products Dry the product, the transport container, the foam inserts and the accessories at a temperature not greater than 40 C/104 F and clean them. Do not repack until every-
thing is dry. Always close the transport container when using in the field. Cables and plugs Keep plugs clean and dry. Blow away any dirt lodged in the plugs of the connecting cables. CTR35, Care and Transport 14 7 7.1 Technical Data CTR35 Technical Data Dimensions (with cover) Weight Power Range Length [mm]
81.65 Length [in]
3.21 Weight [g]
18 Width [mm]
21.40 Width [in]
0.84 Thickness [mm]
17.06 Thickness [in]
0.67 Weight [oz]
0.63 Power supply By USB 2.0 Interface:
Nominal voltage 5.0 V DC (
Voltage range 4.755.25 V
) Power consumption
< 80 mA nominal 150 mA maximum Setup and Conditions With RH16/RH17 under optimal conditions (without video streaming), range up to:
[m]
400
[ft]
1312 Environmental specifications Temperature Operating temperature Storage temperature
[C]
10 +50 20 +60
[F]
+14 +122 4 +140 External Influences Water, dust and sand Humidity Protection IP54 (IEC60529) Up to 90%
Effectively counteract the effects of condensation by periodically drying out the CTR35. Input/Output Port Interface USB 2.0 Type of connector USB 2.0 A, for power supply and communication CTR35, Technical Data 15 7.2 Conformity to National Regulations Conformity to national regulations
FCC Part 15 (applicable in US)
Hereby, Leica Geosystems AG, declares that the product CTR35 are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and other applicable European Directives. The declaration of conformity can be consulted at http://www.leica-geosystems.com/ce. Class 1 equipment according European Directive 1999/5/EC (R&TTE) can be placed on the market and be put into service without restric-
tions in any EEA member state.
The conformity for countries with other national regulations not covered by the FCC part 15 or European directive 1999/5/EC has to be approved prior to use and oper-
ation. Japanese Radio Law and Japanese Telecommunications Business Law Compliance. This device is granted pursuant to the Japanese Radio Law and the Japanese
Telecommunications Business Law. This device should not be modified (otherwise the granted designation number will become invalid).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Frequency band Output power Range [MHz]
Limited to 24022480 Type Radio Radiated power Equivalent Isotropic Radiated Power (EIRP) Output power [mW]
50 CTR35, Technical Data 16 CTR35, Technical Data 17 843695-1.0.0en Original text Printed in Switzerland 2016 Leica Geosystems AG, Heerbrugg, Switzerland Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland Phone +41 71 727 31 31 www.leica-geosystems.com CTR35, Technical Data 19 CTR35, Technical Data 20 CTR35, Technical Data 21
This product uses the FCC Data API but is not endorsed or certified by the FCC