| submitted | available | document details (if available) | source link |
|---|---|---|---|
| May 02 2010 | Microsoft Word - G_User_s Manual.doc Tester Acrobat Distiller 7.0.5 (Windows) |
| various | USER MANUAL | Users Manual | 2.91 MiB | / May 02 2010 |
Order Number Test Report Number
: GETEC-C1-09-265
: GETEC-E3-09-159 FCC Class B Certification Page 1 / 1 APPENDIX G
: USERS MANUAL EUT Type: LED LCD TV/Monitor FCC ID.: BEJ47LE7500UC OWNERS MANUAL LED LCD TV / LCD TV PLASMA TV Please read this manual carefully before operating your set and retain it for future reference. P/NO : SAC34134203 (1001-REV00) www.lge.com WARNING / CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral trian-
gle, is intended to alert the user to the presence of uninsulated dan-
gerous voltage within the products enclo-
sure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equi-
lateral triangle is intended to alert the user to the presence of important oper-
ating and maintenance (servicing) instruc-
tions in the literature accompanying the appliance. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. NOTE TO CABLE/TV INSTALLER This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guide-
lines for proper grounding and, in particular, speci-
fies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. 2 WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. FCC Notice Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equip-
ment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is con-
nected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two condi-
tions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (of the device). Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CAUTION Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the users authority to operate this product. SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 6 Protect the power cord from being walked on or pinched particularly at plugs, conve-
nience receptacles, and the point where they exit from the apparatus. 1 Do not use this apparatus near water. 2 Clean only with dry cloth. 7 Only use attachments/accessories speci-
fied by the manufacturer. 3 Do not block any ventilation openings. Install in accordance with the ma nufacturers instruc-
tions. 8 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over. 4 Do not install near any heat sources such as radiators, heat registers, stoves, or other appa-
ratus (including amplifiers) that produce heat. 9 Unplug this apparatus during lighting storms or when unused for long periods of time. 5 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an elec-
trician for replacement of the obsolete outlet. 10 Refer all servicing to qualified service per-
sonnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is dam-
aged, liquid has been spilled or objects have fallen into the apparatus, the appara-
tus has been exposed to rain or moisture, does not operate normally, or has been dropped. 3 SAFETY INSTRUCTIONS 11 Never touch this apparatus or antenna during a thunder or lighting storm. 12 When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. 13 Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. 14 CAUTION concerning the Power Cord:
It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appli-
ance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, exten-
sion cords, frayed power cords, or damaged or cracked wire insulation are dangerous . Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discon-
tinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not use a damaged or loose power cord. Do not pull on the power cord to unplug the TV. Grasp the plug when unplugging the power cord. 4 15 WARNING - To reduce the risk of fire or elec-
trical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning. 16 Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the appara-
tus (e.g. on shelves above the unit). 17 GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong ground-
ed AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker 18 DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable. 19 As long as this unit is connected to the AC wall outlet, it is not disconnected from AC power even if you turn off the power switch on the unit. 23 Ventilation Install your TV where there is proper ventila-
tion. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in exces-
sively dusty places. 24 Take care not to touch the ventilation open-
ings. When watching the TV for a long period, the ventilation openings may become hot. 25 If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center. 26 Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it. 27 Keep the product away from direct sunlight. 28 For LED LCD TV/LCD TV If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal, there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some tempo-
rary distortion effects on the screen. 20 ANTENNAS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna sys-
tem should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding elec-
trodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70 Ground Clamp Electric Service Equipment Antenna Lead in Wire Antenna Discharge Unit
(NEC Section 810-20) Grounding Conductor
(NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) NEC: National Electrical Code 21 Cleaning When cleaning, unplug the power cord and rub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene. 22 Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV. 5 CONTENTS SAFETY INSTRUCTIONS Important Safety Instructions............................3 FEATURE OF THIS TV ................................ 7 PREPARATION Accessories...........................................................10 Optional Extras ..................................................... 11 Front Panel Information ....................................12 Back Panel Information..................................... 17 Stand instructions ............................................20 VESA Wall Mounting ........................................26 Cable Management ..........................................28 Desktop Pedestal Installation ..........................31 Swivel Stand .........................................................31 Attaching the TV to a Desk ............................32 Kensington Security System ..........................32 Securing the TV to the wall to prevent falling when the tv is used on a stand.....................33 Antenna or Cable Connection.......................34 EXTERNAL EQUIPMENT SETUP HD Receiver Setup............................................35 DVD Setup ...........................................................39 VCR SETUP.........................................................42 Other A/V Source Setup.................................44 USB Connection ................................................45 Headphone Setup....................................................46 Audio Out Connection..................................... 47 External Equipment WIreless Connection
(Optional Extras).................................................48 PC Setup..............................................................49 Network Setup ....................................................56 WATCHING TV / CHANNEL CONTROL Remote Control Functions ..............................64 Turning on the TV..............................................66 Channel Selection..............................................66 Volume Adjustment ..........................................66 6 Initial Setting ....................................................... 67 On-Screen Menus Selection..........................69 Quick Menu .......................................................... 71 Customer Support
- Software Update............................................. 72
- Picture Test/Sound Test................................ 73
- Product/Service Info...................................... 74 Simple Manual.................................................... 75 Channel Setup
- Auto Scan (Auto Tuning).............................. 76
- Add/Delete Channel (Manual Tuning) ..... 77
- Channel Editing............................................... 78 Favorite Channel Setup.................................... 79 Favorite Channel List ........................................ 79 Channel List ....................................................... 80 Channel Information ..........................................81 Channel Brief Information...............................82 Input List ..............................................................83 Input Label...........................................................84 Reset to Factory Default (Initial Setting) .....85 Mode Setting ......................................................86 Demo Mode ........................................................ 87 AV Mode...............................................................88 Game.....................................................................89 SIMPLINK.............................................................90 MY MEDIA Entry Mode ..........................................................92 Connection Method ..........................................93 Movie list.............................................................102 Photo list.............................................................109 Music list.............................................................. 115 DivX Registration Code..................................120 Deactivation ........................................................ 121 NETWORK Legal Notice ...................................................... 122 Netflix ESN (Electronic Serial Number)..... 124 NETCAST TIME SETTING Clock Setting
- Auto Clock Setup......................................... 163
- Manual Clock Setup .................................... 164 Auto On/Off Time Setting............................ 165 Sleep Timer Setting ........................................ 166 PARENTAL CONTROL / RATINGS Set Password & Lock System
- Setting up Your Password...........................167
- Set Password ................................................. 168 Lock System...................................................... 169 Channel Blocking..............................................170 Movie & TV Rating ............................................171 Downloadable Rating.......................................176 External Input Blocking ...................................177 Key Lock ..............................................................178 APPENDIX Troubleshooting.................................................179 Maintenance...................................................... 184 Product Specifications ................................... 185 IR Codes.............................................................190 Open Source License..................................... 192 Netcast Menu.................................................... 125 Yahoo! TV widgets ........................................... 126 PICTURE CONTROL Picture Size (Aspect Ratio) Control............ 134 Picture Wizard................................................... 136
Energy Saving............................................ 138 Preset Picture Settings (Picture Mode)..... 139 Manual Picture Adjustment - User Mode 140 Picture Improvement Technology ............... 141
(Advanced Control) .......................................... 141 Expert Picture control..................................... 142 Picture Reset..................................................... 145 TruMotion .......................................................... 146 LED Local Dimming .......................................147 Power Indicator ................................................148 Image Sticking Minimization (ISM) Method...149 SOUND & LANGUAGE CONTROL Auto Volume......................................................150 Clear Voice II ...................................................... 151 Balance ............................................................... 152 Preset Sound Settings (Sound mode)...... 153 Sound Setting Adjustment - User Mode. 154 Audio Reset....................................................... 155 TV Speakers On/Off Setup .......................... 156 Stereo/SAP Broadcast Setup .......................157 Audio Language ............................................. 158 On-screen Menus Language Selection.... 159 Caption Mode
- Analog Broadcasting System Captions.160
- Digital Broadcasting System Captions.....161
- Caption Option.............................................. 162 7 FEATURE OF THIS TV
Some of these features are not available on all models. High-definition television. High-
resolution digital television broad-
cast and playback system com-
posed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080p, 1080i, and 720p resolutions. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-
Definition Multimedia Interface are trademarks or registered trade-
marks of HDMI Licensing LLC."
ABOUT DIVX VIDEO: DivX is a digital video format created by DivX,Inc. This is an official DivX Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video. ABOUT DIVX VIDEO-ON-
DEMAND: This DivX Certified device must be registered in order to play DivX Video-on-Demand
(VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD. DivX Certified to play DivX video up to HD 1080p, including premi-
um content Pat. 7,295,673;
7,460,688;7,519,274 Displays HDTV programs in full 1920 x 1080p resolution for a more detailed picture. requires a This TV contains the detailed cali-
brations necessary for professional certification by the Imaging Science Foundation. The resulting ISF day and night modes will then be accessible by the user to experi-
ence the best their LG HDTV has to offer. Sophisticated and detailed calibra-
tions can be made through the ISFccc mode. Detailed calibration licensed technician. Please contact your local dealer to inquire about an ISF certified tech-
nician. THX
(Thomlinson Holmans Experiment) is an audio and video certification standard established by George Lucas and Thomlinson. A THX certified display guarantees screen quality that exceeds the dis-
play standard specification in both hardware and software. A unique invisible speaker system tuned by renowned audio expert, Mr. Mark Levinson. Speakers are embedded in strategic spots behind the front cabinet and use minute vibrations to turn the entire front bezel into the speaker system. The result s a clean, polished look, and enhanced audio by increasing the sweet spot, giving a wider and richer sound field. Unlike other sensors which can only sense brightness of ambient light, LGs Intelligent Sensor uses 4,096 sensing steps to evaluate its surroundings. Using a sophisticat-
ed algorithm, the LG processes picture quality elements including brightness, contrast, color, sharp-
ness and white balance. The result is a picture optimized for its sur-
roundings, more pleasing to watch and which can also save up to 50%
in power consumption. 8 View videos and photos and listen to music on your TV through USB 2.0 (videos dependent on model). AV Mode is three preset picture and audio settings. It allows the viewer to quickly switch between common settings. includes Cinema, Sports, and Game Modes. It Automatically enhances and ampli-
fies the sound of human voice fre-
quency range to help keep dia-
logue audible when background noise swells. Stream movies, TV shows and video, and get up to the minute news, stock information and weath-
er updates directly to your TV using Yahoo!, Netflix, YouTube and Vudu. IMPORTANT INFORMATION TO PREVENT IMAGE BURN / BURN-IN ON YOUR TV SCREEN
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as image burn or burn-in. Image burn is not covered under the man-
ufacturers warranty.
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period (2 or more hours for LCD, 1 or more hours for Plasma).
Image burn can also occur on the letter-
boxed areas of your TV if you use the 4:3 aspect ratio setting for an extended period. ON DISPOSAL
(Only Hg lamp used LED LCD TV/LCD TV) The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 9 PREPARATION PREPARATION ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please con-
tact the dealer where you purchased the TV. The accessories included may differ from the images below. 1.5V 1.5V Owners Manual CD Manual, Program CD Remote Control, Batteries (AAA) Not included with all models Option Extras
* Wipe spots on the exterior only with the polishing cloth.
* Do not wipe roughly when remov-
ing stains. Excessive pressure may cause scratches or discoloration. Polishing Cloth When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compli-
ance. D-sub 15 pin Cable Not included with all models Ferrite core can be used to reduce the electromag-
netic waves that may interfere with the TV. Install the Ferrite core on the power cable close to the wall plug. Close to the wall plug. Ferrite Core 50/60PK750
(For 50PK750) x 3 x 4
(M5 x 14)
(M4 x 28) Screws for stand assembly
(Refer to P.20) x 2 Cable Holder
(Refer to p.28) Protection Cover
(Refer to p.21) Power Cord P R E P A R A T O N I 10 32/42/46/52/60LD550, 47/55LD650
(For 32/42LD550) x 8
(M4 x 20) Screws for stand assembly
(Refer to P.22) Screw for stand fixing
(Refer to P.32) Protection Cover
(Refer to P.23) Power Cord 42/47/55LE5400, 42/47/55LE5500, 42/47/55LE7500, 47/55LE8500
(Other models)
(For 55LE5500, 55LE7500,) x 8 x 4 x 4
(M4 x 16)
(M4 x 22)
(M4 x 16) x 2 Screws for stand assembly
(Refer to P.24) Cable Holder
(Refer to p.30) Component gender cable, AV gender cable
(For42/47/55LE7500, 47/55LE8500) P O W E R V O L TV/IN P UT C H FLASHBK 1.5V 1.5V Remote Control, Batteries (AAA)
(For 42/47/55LE7500)
* Wipe spots on the exterior only with the polishing cloth.
* Do not wipe roughly when removing stains. Excessive pressure may cause scratches or discoloration.
* For cleaning front frame, please slowly wipe in one direction after spraying water 1-2 times on cleansing cloths. Please remove exces-
sive moisture after cleaning. Excessive moisture may cause water stains on the frame. OPTIONAL EXTRAS Optional extras can be changed or modified for quality improvement without any notification. Contact your dealer for buying these items. This device only works with compatible LG LED LCD TV, LCD TV, or Plasma TV. Wireless Media Box
(AN-WL100W) Wireless LAN for Broadband/
DLNA Adaptor
(AN-WF100) P R E P A R A T O N I 11 42/47/55LE5400, 42/47/55LE5500, 42/47/55LE7500 Remote Control Sensor Intelligent Sensor Adjusts picture according to the surrounding conditions Power/Standby Indicator Illuminates red in standby mode. Illuminates white when the TV is switched on.
(Can be adjusted using the Power Indicator in the OPTION menu.p.148) SPEAKER Touch Button Light the button by touching first. At this time, you can use the desired button. CH VOL ENTER MENU INPUT CHANNEL
(,) Buttons VOLUME
(-, +) Buttons ENTER Button MENU Button INPUT Button POWER Button P R E P A R A T O N I 15 PREPARATION
Image shown may differ from your TV. 47/55LE8500 Remote Control Sensor Intelligent Sensor Adjusts picture according to the surrounding conditions Power/Standby Indicator Illuminates red in standby mode. Turn off red smoothly when the TV is switchced on. (Can be adjusted using the Power Indicator in the OPTION menu.p.148) SPEAKER Touch Button You can use the desired button function by touching. CH VOL ENTER MENU INPUT CHANNEL
(,) Buttons VOLUME
(-, +) Buttons ENTER Button MENU Button INPUT Button POWER Button P R E P A R A T O N I 16 PREPARATION 42/47/55LE5400, 42/47/55LE5500, 42/47/55LE7500, 47/55LE8500 P R E P A R A T O N I 12 1 2 3 4 RGB IN (PC) RS-232C IN
(SERVICE ONLY)
/DVI IN 3 2 1 LAN WIRELESS CONTROL
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) AUDIO R AUDIO IN AUDIO OUT 2 1 Y PB PR L R VIDEO AUDIO 5 6 A V I N 1 C O M P O N E N T I N ANTENNA/
CABLE IN 9 8 7 18 2 N I B S U 1 N I B S U 3 N I T N E N O P M O C R P B P Y
I O D U A
P H 4 N I 10 8 11 2 2 N I V A I O D U A
O E D V I 6 CAUTION For HDMI IN 4 and USB IN 1, 2
For an optimal connection, HDMI cables and USB devices should have bezels less than 0.39 inches (10 mm) thick.
*A 0.39 inches (10 mm) 1 LAN Network connection for Netflix, Yahoo! TV Widgets, etc. Also used for video, photo and music files on a local network. 2 HDMI/DVI IN, HDMI IN Digital Connection. Supports HD video and Digital audio. Doesnt support 480i. Accepts DVI video using an adapter or HDMI to DVI cable (not included). 3 RGB IN (PC) Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable). AUDIO IN (RGB/DVI) 1/8 (0.32 cm) headphone jack for analog PC audio input. 4 RS-232C IN (SERVICE ONLY), SERVICE ONLY This port is used for service. 5 OPTICAL DIGITAL AUDIO OUT Digital optical audio output for use with amps and home theater systems. Note: In standby mode, this port doesnt work. 6 AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i). 7 ANTENNA/CABLE IN Connect over-the-air or cable signals to this jack. 8 COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video &
red and white for audio. 9 WIRELESS CONTROL Connect the Wireless Ready Dongle to the TV to control the external input devices con-
nected to Media Box wirelessly. 10 USB INPUT Used for viewing videos, photos and listening to MP3s. 11 HEADPHONE INPUT Plug the headphone into the headphone socket. 12 Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. 13 REMOTE CONTROL IN For a wired remote control. P R E P A R A T O N I 19 PREPARATION VESA WALL MOUNTING Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building mate-
rials, please contact your nearest installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer. Model B VESA (A * B) A Standard Screw Quantity Wall Mounting Bracket
(sold separately) RW230 AW-47LG30M 32LD550 200 * 100 M4 42/46LD550, 47LD650, 42/47LE5400, 42/47LE5500, 42/47LE7500, 47LE8500 200 * 200 M6 52LD550, 55LD650, 55LE5400, 55LE5500, 55LE7500, 55LE8500 400 * 400 M6 60LD550 600 * 400 M6 50PK750 400 * 400 M6 60PK750 600 * 400 M8 4 4 4 4 4 4 AW-47LG30M AW-55LH40M AW-55LH40M AW-50PG60M AW-50PG60MS AW-60PG60M AW-60PG60MS P R E P A R A T O N I 26
! NOTE
Screw length needed depends on the wall mount used. For further information, refer to the instructions included with the mount.
Standard dimensions for wall mount kits are shown in the table.
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided.
Do not use screws longer then the standard dimension, as they may cause damage to the inside to the TV.
For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications.
Do not use screws that do not comply with the VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents.
LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installation instructions. CAUTION
Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock. P R E P A R A T O N I 27 DESKTOP PEDESTAL INSTALLATION
Image shown may differ from your TV. For proper ventilation, allow a clearance of 10.1 cm (4 inch) on all four sides from the wall. 10.1 cm (4 inch) 10.1 cm (4 inch) 10.1 cm (4 inch) 10.1 cm (4 inch) CAUTION
Ensure adequate ventilation by following the clearance recommendations.
Do not mount near or above any type of heat source. SWIVEL STAND After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position. P R E P A R A T O N I 31 SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND
You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
Image shown may differ from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children dont climb on or hang from the TV. P R E P A R A T O N I
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.
Use a sturdy rope (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
! NOTE
Use a platform or cabinet strong enough and large enough to support the size and weight of
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the TV. the same. 33 PREPARATION
To prevent damage do not connect to the power outlet until all connections are made between the devices.
Image shown may differ from your TV. ANTENNA OR CABLE CONNECTION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed. P R E P A R A T O N I Wall Antenna Socket Outdoor Antenna
(VHF, UHF) 2. Cable Cable TV Wall Jack Multi-family Dwellings/Apartments
(Connect to wall antenna socket) ANTENNA/
CABLE IN RF Coaxial Wire (75 ) Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the copper wire when connecting the antenna. ANTENNA/
CABLE IN RF Coaxial Wire (75 )
If the antenna needs to be split for two TVs, install a 2-Way Signal Splitter.
For much more information about antennas visit our Knowledgebase at LGknowledgebase.com. Search for antenna. 34 EXTERNAL EQUIPMENT SETUP
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
Image shown may differ from your TV. HD RECEIVER SETUP This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device. Component Connection 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the digital set-top box to the COMPONENT IN VIDEO 1, 2, or 3* jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO 1, 2, or 3*
jacks on the TV. 2. How to use
Turn on the digital set-top box.
(Refer to the owners manual for the digital set-top box operation.)
Select the Component1, Component2, or Component3 input source on the TV using the INPUT button on the remote control.
* Component3: For LED LCD TV Supported Resolutions Y, CB/PB, CR/PR
/DVI IN 3 2 1 Y PB PR L R 1 2 RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL AUDIO IN AUDIO OUT VIDEO L(MONO) AUDIO R A V 2 1 Y PB PR L R VIDEO AUDIO I N 1 C O M P O N E N T I N Signal 480i 480p 720p 1080i 1080p Component HDMI Resolution Horizontal Frequency(KHz) Vertical Frequency(KHz) Yes Yes Yes Yes Yes No Yes Yes Yes Yes 720x480i 720x480p 1280x720p 1920x1080i 1920x1080p 15.73 15.73 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 59.94 60.00 59.94 60.00 59.94 60.00 59.94 60.00 23.976 24.00 29.97 30.00 59.94 60.00 E X T E R N A L E Q U I P M E N T S E T U P 35 EXTERNAL EQUIPMENT SETUP For LED LCD TV 2 N I B S U 1 N I B S U 3 N R P I T N E N O P M O C B P Y
I O D U A
P H 4 N I 2 N I V A I O D U A
O E D V I 1 2 R L PR PB Y E X T E R N A L E Q U I P M E N T S E T U P 36 HDMI Connection 1. How to connect 1 Connect the digital set-top box to HDMI/DVI IN 1, 2, 3, or 4 jack on the TV. 2 No separate audio connection is necessary. HDMI supports both audio and video. 2. How to use
Turn on the digital set-top box.
(Refer to the owners manual for the digital set-
top box.)
Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the INPUT button on the remote control. LAN WIRELESS CONTROL
/DVI IN 3 2 1 RGB IN (PC) RS-232
(SERVICE
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO AUDIO IN AUDIO OUT 2 1 Y PB PR VIDEO L A 1 HDMI OUTPUT
! NOTE
If an HDMI cable doesnt support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
HDMI Audio Supported Format: AC3
(32KHz, 44.1KHz,48KHz), Linear PCM (32KHz, 44.1KHz,48KHz) HDMI-DTV Resolution Horizontal Frequency(KHz) Vertical Frequency(KHz) 720x480p 1280x720p 1920x1080i 1920x1080p 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 59.94 60.00 59.94 60.00 59.94 60.00 23.976 24.00 29.97 30.00 59.94 60.00 E X T E R N A L E Q U I P M E N T S E T U P 37 EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection 1. How to connect E X T E R N A L E Q U I P M E N T S E T U P 1 Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1, 2, 3, or 4* jack on the TV. 2 Connect the digital set-top box audio output to the AUDIO IN (RGB/DVI) jack on the TV. 2. How to use
Turn on the digital set-top box.
(Refer to the owners manual for the digital set-
top box.)
Select the HDMI1, HDMI2, HDMI3, or HDMI4* input source on the TV using the INPUT button on the remote control. LAN WIRELESS CONTROL
/DVI IN 3 2 1 RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) AUDIO R AUDIO IN AUDIO OUT 2 1 Y PB PR L R VIDEO AUDIO 1 2
* HDMI 4: For Plasma TV DVI OUTPUT R L AUDIO
! NOTE
A DVI to HDMI cable or adapter is required for this con-
nection. DVI doesn't support audio, so a separate audio connection is necessary. 38 DVD SETUP Component Connection 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO 1, 2, or 3*
jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 Connect the audio outputs of the DVD to the COMPONENT IN AUDIO 1, 2, or 3* jacks on the TV. 2. How to use
Turn on the DVD player, insert a DVD.
Select the Component1, Component2, or Component3 input source on the TV using the INPUT button on the remote control.
Refer to the DVD players manual for operating instructions.
/DVI IN 3 2 1 S L
* Component3: For LED LCD TV For LED LCD TV Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. 2 N I B S U 1 N I B S U Y PB PR L R 1 2 RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL AUDIO IN AUDIO OUT VIDEO L(MONO) AUDIO R A V 2 1 Y PB PR L R VIDEO AUDIO I N 1 C O M P O N E N T I N Component ports on the TV Video output ports on DVD player Y Y Y Y Y PB PB B-Y Cb Pb PR PR R-Y Cr Pr 3 N I T N E N O P M O C R P B P Y
I O D U A
P H 4 N I 2 N I V A I O D U A
O E D V I 1 2 R L PR PB Y E X T E R N A L E Q U I P M E N T S E T U P 39 EXTERNAL EQUIPMENT SETUP Composite (RCA) Connection 1. How to connect 1 Connect the AUDIO/VIDEO jacks between TV and DVD. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use
Turn on the DVD player, insert a DVD.
Select the AV1 or AV2 input source on the TV using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instructions.
/DVI IN 3 2 1 S L For LED LCD TV VIDEO L R AUDIO E X T E R N A L E Q U I P M E N T S E T U P 40 RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL AUDIO IN AUDIO OUT VIDEO L(MONO) AUDIO R A V I N 1 C O M P O N E N T I N 2 N I V A I O D U A
O E D V I 2 1 Y PB PR L R VIDEO AUDIO 1 VIDEO L R AUDIO 2 N I B S U 1 N I B S U 3 N I T N E N O P M O C R P B P Y
I O D U A
P H 4 N I HDMI Connection 1. How to connect 1 Connect the HDMI output of the DVD to the HDMI/DVI IN 1, 2, 3 or 4 jack on the TV. 2 No separate audio connection is necessary. HDMI supports both audio and video. LAN WIRELESS CONTROL 2. How to use
Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instructions. RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) AUDIO R AUDIO IN AUDIO OUT 2 1 Y PB PR L R VIDEO AUDIO A V I N 1 C O M P O N E N T I N
/DVI IN 3 2 1 1 HDMI OUTPUT
! NOTE
If an HDMI cable doesnt support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
HDMI Audio Supported Format: AC3
(32KHz, 44.1KHz,48KHz), Linear PCM (32KHz, 44.1KHz,48KHz) E X T E R N A L E Q U I P M E N T S E T U P 41 EXTERNAL EQUIPMENT SETUP VCR SETUP Antenna Connection 1. How to connect 1 Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN socket on the TV. ANTENNA/
CABLE IN 1 2 Connect the antenna cable to the RF antenna in socket of the VCR. 2. How to use
Set VCR output switch to 3 or 4 and then tune TV to the same channel num-
ber.
Insert a video tape into the VCR and press PLAY on the VCR (Refer to the VCR owners manual). ANT OUT S-VIDEO VIDEO L R AUDIO ANT IN OUTPUT SWITCH Wall Jack 2 Antenna E X T E R N A L E Q U I P M E N T S E T U P 42 Composite (RCA) Connection 1. How to connect 1 Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.)
Select the AV1 or AV2 input source on the TV using the INPUT button on the remote control. SS OL
/DVI IN 3 2 1 RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL AUDIO IN AUDIO OUT VIDEO L(MONO) AUDIO R A V 2 1 Y PB PR L R VIDEO AUDIO 1
! NOTE
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the TV. ANT IN S-VIDEO VIDEO L R AUDIO ANT OUT OUTPUT SWITCH For LED LCD TV 2 N I B S U 1 N I B S U 3 N I T N E N O P M O C R P B P Y
I O D U A
P H 4 N I ANT IN S-VIDEO VIDEO L R AUDIO ANT OUT OUTPUT SWITCH I N 1 C O M P O N E N T I N 2 N I V A I O D U A
O E D V I E X T E R N A L E Q U I P M E N T S E T U P 43 EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP 1. How to connect Camcorder Video Game Set VIDEO L R 1 2 N I B S U 1 N I B S U 4 N I
P H I R O D U A
) O N O M
L O E D V I AV IN 2 1 Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors.
(Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use
Select the AV1 or AV2 input source on the TV using the INPUT button on the remote control.
Operate the corresponding external equipment. E X T E R N A L E Q U I P M E N T S E T U P 44 USB CONNECTION 1. How to connect 1 Connect the USB device to the USB IN 1 or 2 jack on the side of TV. 2. How to use
After connecting the USB IN jack, you use the USB function. (p.93) 2 N I B S U 1 N I B S U 4 N I
P H I R O D U A
) O N O M
L or Memory Key E X T E R N A L E Q U I P M E N T S E T U P 45 EXTERNAL EQUIPMENT SETUP HEADPHONE SETUP (FOR LED LCD TV/LCD TV) You can listen to the sound through the headphone. 1. How to connect 1 Plug the headphone into the head-
phone socket. 2 To adjust the headphone volume, press the VOL +/- button. If you press the MUTE button, the sound from the headphone is switched off.
P H
! NOTE
AUDIO menu options are disabled when connecting a headphone.
When changing AV MODE with a headphone con-
nected, the change is applied to video but not to audio.
Optical Digital Audio Out is not available when con-
necting a headphone. E X T E R N A L E Q U I P M E N T S E T U P 46 AUDIO OUT CONNECTION Send the TVs audio to external audio equipment via the Audio Output port. If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
/DVI IN 3 2 1
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) AUDIO R AUDIO IN AUDIO OUT Y PB 1 PR 2 1 VIDEO L R AUDIO A V I N 1 C O M P O N E N T I N LESS TROL 2 1. How to connect 1 Connect one end of the optical cable to the TV port of OPTICAL DIGITAL AUDIO OUT. 2 Connect the other end of the optical cable to the digital audio input on the audio equip-
ment. 3 Set the TV Speaker option - Off in the AUDIO menu. (p.156). See the external audio equipment instruction manual for operation.
! NOTE
When connecting with external audio equipment, such as amplifiers or speakers, you can turn the TV speakers off in the menu. (p.156) CAUTION
Do not look into the optical output port. Looking at the laser beam may damage your vision.
Audio with ACP (Audio Copy Protection) function may block digital audio output. E X T E R N A L E Q U I P M E N T S E T U P 47 EXTERNAL EQUIPMENT SETUP EXTERNAL EQUIPMENT WIRELESS CONNECTION
(OPTIONAL EXTRAS) LG TVs with a Wireless Control port support the LG Wireless Media Box (AN-WL100), which is sold separately. When you connect the wireless ready dongle (included with the media box) to the TV, external devices can be connected to the LG Wireless Media Box and video and audio will be sent to the TV wirelessly. E X T E R N A L E Q U I P M E N T S E T U P 48 COM1 COM2 AV1 AV2 1 2 3 4 RGB WIRELESS WIRELESS CONTROL OUT
/DVI IN 3 2 1 LAN WIRELESS CONTROL RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) AUDIO R AUDIO IN AUDIO OUT 2 1 Y PB PR L R VIDEO AUDIO A V I N 1 C O M P O N E N T I N 1. How to connect 1 Connect the WIRELESS CONTROL jack of the Wireless Ready Dongle to the WIRELESS CONTROL jack on the TV. 2 Connect HDMI OUT jack of the Wireless Ready Dongle to the HDMI IN jack on the TV. 2. How to use
Select the desired input source on the TV using the INPUT button on the remote control.
Refer to the Wireless Media Box manual for operating instructions. PC SETUP This TV provides Plug and Play capability, meaning that a PC adjusts automatically to the TV's set-
tings. VGA (D-Sub 15 Pin) Connection 1. How to connect 1 Connect the VGA output of the PC to the RGB IN (PC) jack on the TV. 2 Connect PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV. 2. How to use
Turn on the PC and the TV.
Select the RGB-PC input source on the TV using the INPUT button on the remote control.
/DVI IN 3 2 1 LAN WIRELESS CONTROL RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) AUDIO R AUDIO IN AUDIO OUT 2 1 Y PB PR L R VIDEO AUDIO A V I N 1 C O M P O N E N T I N 2 1 AUDIO RGB OUTPUT E X T E R N A L E Q U I P M E N T S E T U P 49 EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection 1. How to connect E X T E R N A L E Q U I P M E N T S E T U P 1 Connect the DVI output of the PC to the HDMI/
DVI IN 1, 2, 3, or 4* jack on the TV. 2 Connect the PC audio output to the AUDIO IN
(RGB/DVI) jack on the TV. 2. How to use
Turn on the PC and the TV.
Select the HDMI1, HDMI2, HDMI3, or HDMI4* input source on the TV using the INPUT button on the remote control.
* HDMI 4: For Plasma TV LAN WIRELESS CONTROL
/DVI IN 3 2 1 RGB IN (PC) RS-232C
(SERVICE ONL
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) A AUDIO IN AUDIO OUT 2 1 Y PB PR L VIDEO AUD 1 2 DVI OUTPUT AUDIO 50
! NOTE
To get the the best picture quality, adjust the PC graphics card to 1920x1080.
Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.
In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or bright-
ness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become permanently imprinted on the screen.
The synchronization input form for Horizontal and Vertical frequencies is separate.
Depending on the graphics card, some resolution settings may not allow the image to be posi-
tioned on the screen properly.
If you experience overscan issues when using HDMI-PC 1920x1080, change aspect ratio to Just scan.
When selecting HDMI-PC, set the Input Label - PC in the OPTION menu. Supported Display Specifications (RGB-PC, HDMI-PC) Resolution Horizontal Frequency(KHz) Vertical Frequency(KHz) 640x350 31.468 720x400 640x480 800x600 31.469 31.469 37.879 1024x768 48.363 1280x768 1360x768 47.776 47.712 1280x1024 63.981 1600x1200 75.00 1920x1080 RGB-PC 1920x1080 HDMI-PC 66.587 67.50 70.09 70.08 59.94 60.31 60.00 59.87 60.015 60.02 60.00 59.934 60.00 E X T E R N A L E Q U I P M E N T S E T U P 51 EXTERNAL EQUIPMENT SETUP NETWORK SETUP Wired Network Connection This TV can be connected to a local area network (LAN) via the LAN port. After making the physical connection, the TV needs to be set up for network communication.
/DVI IN 3 2 1 LAN 1 WIRELESS CONTROL RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) AUDIO R AUDIO IN AUDIO OUT 2 1 Y PB PR L R VIDEO AUDIO A V I N 1 C O M P O N E N T I N Broadband modem Router Broadband Service Broadband modem 1. How to connect 1 Connect the LAN port of the Modem or Router to the LAN port on the TV. Broadband Service 2. How to use
Select Network Setting in the NETWORK menu (p.59).
After connecting the LAN port, use the NETCAST menu (p.125).
For more information about NETCAST setup and troubleshooting, visit our Knowledgebase at LGknowledgebase.com. Search for NetCast. CAUTION
Do not connect a modular phone cable to the LAN port.
Since there are various connection methods, please follow the specifications of your telecommu-
nication carrier or internet service provider. E X T E R N A L E Q U I P M E N T S E T U P 56 Wireless Network Connection The LG Wireless LAN for Broadband/DLNA Adaptor (AN-WF100), which is sold separately, allows the TV to connect to a wireless lan network. The network configuration and connection method may vary depending on the equipment in use and the network environment. Refer to the setup instructions supplied with your access point or wireless router for detailed connection steps and network settings. 2 N I B S U 1 N I B S U 4 N I
P H I R O D U A
) O N O M
L O E D V I AV IN 2 1. How to connect 1 Connect the LG Wireless LAN for Broadband/DLNA Adaptor (AN-WF100) (sold sepa-
rately) to the USB IN 1 or 2 port on the TV. 2. How to use
Select Network Setting in the NETWORK menu (p.59).
After connecting, you can use the NETCAST menu (p.125). Wi-Fi USB dongle (AN-WF100) SPEC Standard IEEE 802.11a/b/g/n Host interface USB 2.0 Frequency Range Security Data rate 2.400~2.483 GHz 5.150~5.250 GHz 5.725~5.850 GHz 64/128 bit WEP, WPA, TKIP, AES, WPS (PIN, PBC) 802.11 a/g: 54 Mbps 802.11 b: 11 Mbps 802.11 n: 300 Mbps (40 MHz) Sensitivity Output power 802.11a : -72dBm (54Mbps) 802.11b: -84dBm (11, 5.5, 2, 1Mbps) 802.11g: -72dBm (54Mbps) 802.11n: -64dBm (20MHz)/
-61dBm (40MHz) 802.11a: 14dBm (54Mbps) 802.11b: 16.5dBm (11, 5.5, 2, 1Mbps) 802.11g: 14dBm (54Mbps) 802.11n: (2.4Ghz) 13.5dBm
(20MHz)/ 13.5dBm (40MHz) E X T E R N A L E Q U I P M E N T S E T U P 57 EXTERNAL EQUIPMENT SETUP
! NOTE
For more information about NETCAST setup and troubleshooting, visit our Knowledgebase at LGknowledgebase.com. Search for NETCAST.
Use a standard LAN cable with this TV. Cat5 or better with a RJ45 connector.
Many network connection problems during set up can often be fixed by re-setting the router or modem. After connecting the player to the home network, quickly power off and/or dis-
connect the power cable of the home network router or cable modem. Then power on and/or connect the power cable again.
Depending on the internet service provider
(ISP), the number of devices that can receive internet service may be limited by the appli-
cable terms of service. For details, contact your ISP.
LG is not responsible for any malfunction of the TV and/or the internet connection feature due to communication errors/malfunctions associated with your broadband internet con-
nection, or other connected equipment.
LG is not responsible for problems within your internet connection.
Some content available through the network connection may not be compatible with the TV. If you have questions about such content, please contact the producer of the content.
You may experience undesired results if the network connection speed does not meet the requirements of the content being accessed.
Some internet connection operations may not be possible due to certain restrictions set by the Internet service provider (ISP) supplying your broadband Internet connection.
Any fees charged by an ISP including, without limitation, connection charges are your respon-
sibility.
A 10 Base-T or 100 Base-TX LAN port is required for connection to this TV. If your inter-
net service does not allow for such a connec-
tion, you will not be able to connect the TV.
A DSL modem is required to use DSL service and a cable modem is required to use cable modem service. Depending on the access method of and subscriber agreement with your ISP, you may not be able to use the inter-
net connection feature contained in this TV or you may be limited to the number of devices you can connect at the same time. (If your ISP limits sub-scription to one device, this TV may not be allowed to connect when a PC is already connected.)
The use of a Router may not be allowed or its usage may be limited depending on the policies and restrictions of your ISP. For details, contact your ISP directly.
The wireless network operates at 2.4 GHz radio frequencies that are also used by other household devices such as cordless tele-
phone, Bluetooth devices, microwave oven, and can be affected by interference from them.
Turn off all unused network equipment in your local home network. Some devices may gen-
erate network traffic.
In some instances, placing the access point or wireless router higher up away from the floor may improve the reception.
The reception quality over wireless depends on many factors such as type of the access point, distance between the TV and access point, and the location of the TV. E X T E R N A L E Q U I P M E N T S E T U P 58 WATCHING TV / CHANNEL CONTROL WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS When using the remote control, aim it at the remote control sensor on the TV. ENERGY AV MODE INPUT LIGHT TV SAVING 1 2 ABC 3 DEF 4 GHI 5 JKL 6MNO 9WXYZ 7PQRS 8 TUV LIST VOL 0 MARK FAV CHAR/NUM RATIO DELETE MUTE FLASHBK CH P A G E MENU Q.MENU ENTER BACK EXIT FREEZE INFO MENU Q.MENU ENTER BACK INFO EXIT FREEZE W A T C H I N G T V
C H A N N E L C O N T R O L 64 POWER Turns the TV on from standby or off to standby. LIGHT Illuminates the remote control buttons.
(Except 32/42/46/52/60LD550, 47/55LD650) ENERGY SAVING Adjusts the Energy Saving setting. p.138 AV MODE Toggles through preset Video and Audio modes. p.88 INPUT Rotates through inputs. Also switches the TV on from standby. p.83 TV Returns to the last TV channel. NUMBER button
(DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2, etc. LIST Displays the channel table. p.80 FLASHBK Tunes to the last channel viewed. MENU Displays the main menu or clears all on-screen displays and return to TV viewing. NETCAST Select the desired NETCAST menu source. p.125 Q.MENU Opens the list of Quick Menu options. p.71 THUMBSTICK
(Up/Down/Left Right/ENTER) Navigates the on-screen menus and adjusts the system settings to your preference. BACK Allows the user to move return one step in an interactive application or other user interaction function. WIDGETS WIDGETS for showing or hiding the Yahoo! Dock and accessing the Yahoo! TV Widgets user experience.
p.127-133 INFO Displays channel information at the top of the screen.
p.81 EXIT Clears all on-screen displays and return to TV viewing. SIMPLINK See a list of AV devices connected to TV. When you toggle this button, the SIMPLINK menu appears at the screen. p.90-91 ENERGY AV MODE INPUT LIGHT TV SAVING 1 2 ABC 3 DEF 4 GHI 5 JKL 6MNO 9WXYZ 7PQRS 8 TUV LIST VOL 0 MARK FAV CHAR/NUM RATIO DELETE MUTE FLASHBK CH P A G E MENU Q.MENU ENTER BACK EXIT FREEZE INFO MENU Q.MENU ENTER BACK INFO EXIT FREEZE VOLUME UP/DOWN Adjusts the volume. FAV Set up desired favorite channels list. p.79 MARK Select the input to apply the Picture Wizard settings.
p.137 Use to mark or unmark a photo/music/movie. p.105, 110, 116 RATIO Changes the aspect ratio. p.134 CHAR/NUM Shifts the Character or Number for YouTube. MUTE Switches the sound on or off. p.66 DELETE Deleted the character or number on the screen. CHANNEL UP/DOWN PAGE UP/DOWN COLOR BUTTON USB, SIMPLINK Control buttons FREEZE
(For Plasma TV) Changes the channel. Moves from one full set of screen information to the next one. Access special functions in some menus.
Controls MY MEDIA menu (Movie List, Photo List, Music List)
Controls the SIMPLINK compatible devices. Pause the present picture at the screen. (It doesnt work at USB Mode and Simplink.) The TV returns to normal viewing automatically if no signal is received or no operation is performed for 5 minutes. If you keep the screen in Freeze condition, the residu-
al image can exist. Installing Batteries
Open the battery compartment cover on the back side and install the batter-
ies matching correct polarity.
Install two 1.5V AAA batteries. Dont mix old or used batteries with new ones.
Close cover. W A T C H I N G T V
C H A N N E L C O N T R O L 65 WATCHING TV / CHANNEL CONTROL TURNING ON THE TV 1 2 3 First, connect power cord correctly. At this moment, the TV switches to standby mode.
In standby mode to turn TV on, press the the POWER, INPUT, CH (or ), Number (0~9) button on the remote control.
/ I, INPUT, CH (or ) button on the TV or press Select the viewing source by using the INPUT button on the remote control. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.
! NOTE
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
If you do not complete the Initial setting, it will appear whenever the TV is switched on until the Initial setting procedure is completed. CHANNEL SELECTION 1 Press the CH (or ) or NUMBER buttons to select a channel number. VOLUME ADJUSTMENT Adjust the volume to suit your personal preference. 1 2 3 Press the VOL (+ or -) button to adjust the volume. If you want to switch the sound off, press the MUTE button. You can cancel the Mute function by pressing the MUTE or VOL (+ or -) button. W A T C H I N G T V
C H A N N E L C O N T R O L 66 CONNECTION METHOD USB Connection Connect the USB device to the USB IN jack on the TV. 1 2 N I B S U 1 N I B S U 4 N I Memory Key Precautions when using the USB device
Only a USB storage device is recognizable.
Connecting a USB storage device through a USB hub is not supported.
A USB storage device which uses its own driver may not be recognized.
The recognition speed of a USB storage device may depend on each device.
Please do not turn off the TV or unplug the USB device when the connected USB storage device is working. When such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.
Only use a USB storage device which has normal music files or image files.
Please use only a USB storage device which was formatted as a FAT 32 or NTFS file system pro-
vided with the Windows operating system. Others may not be recognized.
Some USB storage devices require a power adapter. The power adapter must be connected in order to be seen by the TV.
If a device is not recognized by the TV, try a different cable. Excessively long cables are not sup-
ported.
Some USB storage devices may not be supported or operate properly.
Please backup important files because data on USB device could be damaged. Data management is consumer's responsibility and as a result, the manufacturer does not cover data damage.
If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can use up to 4 partitions or USB memory devices.
In case of USB storage devices formatted as NTFS, deletion is not supported.
File alignment method of USB storage device is similar to Window XP and file names can be up to 100 English characters.
The recommended capacity is 1TB or less for a USB external hard disk and 32 GB or less for USB memory.
If a USB external hard disk with a Energy Saving function doesnt work, turn the hard disk off and on again to make it work properly. Refer to the user manual of the USB external hard disk.
USB storage devices below USB 2.0 are supported as well. But they may not work properly in the movie list. M Y M E D I A 93 MY MEDIA Viewing Files on the Network You can view the photos or listen to music files from folders shared on the network. 1 Set a share folder (CIFS: Common Internet File System) on the PC (Refer to P.95). 2 Connect the LAN port of the Modem or Router to the LAN port on the TV. i.e) LED LCD TV/LCD TV
/DVI IN 3 2 1 LAN WIRELESS CONTROL RGB IN (PC) RS-232C IN
(SERVICE ONLY)
(RGB/DVI) OPTICAL DIGITAL VIDEO L(MONO) AUDIO R AUDIO IN AUDIO OUT 2 1 Y PB PR L R VIDEO AUDIO A V I N 1 C O M P O N E N T I N Broadband modem Broadband Service Router Broadband modem Broadband Service 3 4 MENU ENTER Select MY MEDIA. Select Movie List, Photo List or Music List.
Connect the PC and TV using a shar-
ing device so that you can see the PCs shared files on the TV.
How to set a share folder may differ depending on the Windows version.
The speed may be slow or it may cause an error if you try to access a folder from two TVs at the same time.
Because files could be deleted from a shared PC, set the user access level to Read Only.
Do not share any important personal documents as it may be accessed by a different PC.
If you rename or disable a shared folder on the PC after mounting, you cannot mount it again.
If the status of the network or a share folder on the PC is changed, search is run again when entering the highest folder in the menu.
Maximum of 32 computers can be shared. MY MEDIA
List M Y M E D I A 96 DLNA About DLNA This TV is a DLNA Certified digital media product that can display and play movie, photo and music content from your DLNA Certified network device and DLNA server. The Digital Living Network Alliance
(DLNA) is a cross-industry organization of consumer electronics, computing industry and mobile device companies. Digital Living provides consumers with easy sharing of digital media through a wired or wireless network in the home. The DLNA certification logo makes it easy to find products that comply with the DLNA Interoperability Guidelines. This unit complies with DLNA Interoperability Guidelines v1.5. When a PC running DLNA server software or other DLNA compatible device is connected to this TV, some setting changes of software or other devices may be required. Please refer to the operating instructions for the software or device for more information.
! NOTE
The supplied Nero MediaHome 4 Essentials CD-ROM is a customized software edition only for sharing files and folders to this TV.
The supplied Nero MediaHome 4 Essentials software does not support following functions:
Transcoding, Remote UI, TV control, Internet services and Apple iTunes
This manual explains operations with the English version of Nero MediaHome 4 Essentials as examples. Follow the explanation referring to the actual operations of your language version. M Y M E D I A 97 MY MEDIA Installing Nero MediaHome 4 Essentials Nero MediaHome 4 Essentials is easy to use DLNA server software for Windows. If you are already using DLNA server software on your PC, Nero MediaHome is not required. Nero MediaHome is not required for Windows 7 since it has a built-in DLNA server. Requirement PC system before you install Nero MediaHome 4 Essentials
Windows XP (Service Pack 2 or higher), Windows Vista (no Service Pack required), Windows XP Media Center Edition 2005 (Service Pack 2 or higher), Windows Server 2003
Windows Vista 64-bit edition (application runs in 32-bit mode)
Hard drive space: 200 MB hard drive space for a typical installation of Nero MediaHome stand-
alone
1.2 GHz Intel Pentium III or AMD Sempron 2200+ processors
Memory: 256 MB RAM
Graphics card with at least 32 MB video memory, minimum resolution of 800 x 600 pixels, and 16-bit color settings
Windows Internet Explorer 6.0 or higher
DirectX 9.0c revision 30 (August 2006) or higher
Network environment: 100 Mb Ethernet, WLAN (IEEE 802.11b/g/n) M Y M E D I A 98 1 Start up your computer, and insert the Nero MediaHome 4 Essentials CD-ROM into your compu-
ters CD-ROM drive. An installation wizard will walk you through the quick and uncomplicated installation process. 2 Close all Microsoft Windows programs and exit any anti-virus software that may be running. 3 Insert the Nero MediaHome 4 Essentials CD-ROM into your computers CD-ROM drive. 4 Click Nero MediaHome 4 Essentials. The installation is prepared and the installation wizard appears. 5 Click the Next button to display the serial number input screen. Click Next to go to the next step. 6 If you accept all conditions, click I accept the License Conditions check box and click Next. Installation is not possible without this agreement. 7 Click Typical and click Next. The installation process is started. 8 If you want to take part in the anonymous collection of data, select the check box and click the Next button. 9 Click the Exit button to complete the installation. M Y M E D I A 99 MY MEDIA Sharing files and folders After installing Nero MediaHome, you must add folders you wish to share. 1 Double-click the Nero MediaHome 4 Essentials icon on the desktop. 2 Click Network icon on the left and define your network name in the Network name field. The Network name you enter will be recognized by your TV. 3 Click Shares icon on the left. 4 Click Local Folders tab on the Shared screen. 5 Click Add icon to open the Browse Folder window. M Y M E D I A 6 Select the folder containing the files you want to share. The selected folder is added to the list of shared folders. 7 Click Start Server icon to start the server.
! NOTE
If the shared folders or files are not displayed on the TV, click the folder on the Local Folders tab and click Rescan Folder at the More button.
Visit www.nero.com for more information and software tools. 100 Playing back shared contents You can display and play movie, photo and music content stored on your computer or other DLNA media servers. 1 Start the server on your computer or other device that connected on your home network. 2 MENU Select MY MEDIA. 3 4 ENTER ENTER Select Movie List, Photo List or Music List. Select the DLNA. Depending on the media server, this TV may need to get the permission from the server. If you want to re-scan available media server, press blue color button.
! NOTE
To play the file on the media server, the TV and the media server must be connected to the same access point.
Because the compatibility and available playback functions on the MY MEDIA menu are tested on the bundle DLNA server (Nero MediaHome 4 Essentials) environment, file requirements and playback functions on the MY MEDIA may differ depending on media servers.
The file requirements on this page are not always compatible. There may have some restrictions by file features and media servers ability.
Movie thumbnail is not supported in DLNA Movie.
If there is an unplayable music file in the MY MEDIA menu, the TV will skip the file and play next file.
The file information indicated on the screen may not always correct for music and movie files in MY MEDIA menu
This TV only supports movie subtitle files supplied by Nero MediaHome 4.
The subtitle file name and movie file name have to be the same and located at the same folder.
If subtitle files have been added after a directory has been indexed already, the user has to remove and re-add the folder to the list of shares.
The playback and operating quality of the MY MEDIA function may be affected by your home network condition.
The files from removable media such as USB drive, DVD-drive etc. on your media server may not share properly. M Y M E D I A 101 MY MEDIA MOVIE LIST It displays all of the video files it recognizes. The On-Screen Display on your model may be slightly different. Supported movie file
Resolution: under 1920 pixel (width) x 1080 pixel (height)
Frame Rate: under 30 frame/sec (1920x1080), under 60 frame/sec (1280x720) Precautions when playing the video files
Some user-created subtitles may not work properly.
Some special characters are not supported in subtitles.
HTML tags are not supported in subtitles.
Time information in an external subtitle file should be arranged in ascending order to be played.
The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the audio language is changed.
A damaged video file may not be played correctly, or some functions may not be usable.
Video files produced with some encoders may not be played correctly.
If the video and audio structure of recorded file is not interleaved, the file not playback properly.
Video with resolution higher than maximum resolution supported for each frame, cannot be guar-
anteed for smooth playback.
Movie files other than the specified types and formats may not work properly.
The movie file encoded by the GMC (Global Motion Compensation) is not supported.
Only the files saved in ASCII Code is supported in subtitles.
Only 250 Korean characters, 500 letters and 500 numbers are supported for each line of the
Only 10,000 sync blocks are supported within the subtitle file.
We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264.
DTS Audio codec is not supported.
A video file more than 30GB in file size is not supported for playback.
Playing a video via a USB connection that doesnt support high speed may not work properly.
USB storage devices below USB 2.0 are supported as well. But they may not work properly in the subtitle. movie list.
The video file and its subtitle file must be located in the same folder. At this time, a video file name and its subtitle file name must be identical for it to be displayed.
When you are watching a movie via the Movie List function, you can adjust the picture with the ENERGY SAVING and AV MODE button on the remote control. User setup for each picture mode is not supported. M Y M E D I A 102 Codec Profile/Level Support Explanation VC-1 Advanced Profile Advanced Profile@Level 3
(e.g. 720p60, 1080i60, 1080p30) VC-1 Simple and Main Profiles Simple Profile@Medium Level (e.g. CIF, QVGA) Main Profile@High Level (e.g. 1080p30) Only streams compliant to SMPTE 421M VC-1 standard are supported. Supported Video Formats File Extensions Audio/
Video WMA Standard WMA 9 Professional DivX3.11 DivX4 DivX5 DivX6 XViD H.264 / AVC MPEG-1 Layer I, II Audio MPEG-1 Layer III (MP3) AC-3 H.264 / AVC
.asf
.wmv
.wma
.divx
.avi
.mp4
.m4a
.m4v
.mkv
.ts
.trp
.tp
.vob
.mpg Video Audio Video Video Audio Video Audio Video Audio Video Audio Video Audio Advanced Simple Profile
(e.g. 720p/1080i) Main Profile@ Level 4.1 High Profile@ Level 4.1
(e.g. 720p60, 1080i60, 1080p30) Main Profile@ Level 4.1 High Profile@ Level 4.1
(e.g. 720p60, 1080i60, 1080p30) Global motion compen-
sation or quarterpel motion estimation does not supported. Streams using this syntax are not supported. M Y M E D I A Global motion compen-
sation or quarterpel motion estimation does not supported. Streams using this syntax are not supported. Most of the MKV con-
tent available is encod-
ed by the open source x264 codec. MPEG-4 Part 2 Advanced Simple Profile (e.g. 720p/1080i) AAC H.264 / AVC AAC AC-3 H.264 / AVC AAC-LC and AAC-HE Main Profile@ Level 4.1 High Profile@ Level 4.1
(e.g. 720p60, 1080i60, 1080p30) AAC-LC and AAC-HE Main Profile@ Level 4.1 High Profile@ Level 4.1
(e.g. 720p60, 1080i60, 1080p30) MPEG-2 Main Profile@High Level(e.g. 720p60, 1080i60) VC-1 MPEG-1Layer I, II MPEG-1 Layer III (MP3) AC-3 AAC MPEG-1 MPEG-2 AC-3 MPEG-1Layer I, II DVD-LPCM MPEG-1 MPEG-2 MPEG-1Layer I, II Simple Profile@Medium Level
(e.g. CIF, QVGA) Main Profile@High Level
(e.g. 1080p30) Advanced Profile@Level3
(e.g. 720p60, 1080i60, 1080p30) Only streams compliant to SMPTE 421M VC-1 standard are supported. AAC-LC and AAC-HE Main Profile@High Level (e.g. 720p60, 1080i60) Main Profile@High Level (e.g. 720p60, 1080i60) Only streams compliant configured properly for TS, PS or ES 103 PHOTO LIST The On-Screen Display on your model may be slightly different. Supported photo file: *.JPG
Baseline: 64 pixel (width) x 64 pixel (height) to 15360 pixel (width) x 8640 pixel (height)
Progressive: 64 pixel (width) x 64 pixel (height) to 1920 pixel (width) x 1440 pixel (height)
You can play JPEG files only.
Non-supported files are displayed in the form of predefined icon. Screen Components 1 MENU Select MY MEDIA. 2 ENTER ENTER Select Photo List. 1 Moves to upper level folder 2 Current page/Total pages 3 Corresponding buttons on the remote control 4 Contents under the folder focused on 1 5 Current page/total pages of contents
USB 1 XTICK 2 Page 1/1 1
Page 1/1 1.EMF
20090711 20090810
20091010
Basic Test Kit
FHD HD MV
TS
Exit
3 M Y M E D I A 5 4 RED Change to a different input. GREEN Move to Music List or Movie List. YELLOW Change Numbers: Changes the number or thumbnails displayed at a time. BLUE Allows you to mark certain files. EXIT Return to TV viewing. 109 MUSIC LIST Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be supported by this TV. The On Screen Display below may be different from your TV. Images are an example to assist with the TV operation. Supported Music File: *.MP3 Bit rate range: 32 Kbps ~ 320 Kbps
Screen Components 1 MENU Select MY MEDIA. 2 ENTER ENTER Select Music List. 1 Preview: If any album jacket for the file (Album Art Image) exists, this picture is displayed. 2 Moves to upper level folder 3 Current page/Total pages 4 Corresponding buttons on the remote control 5 Contents under the folder focused on 1 6 Current page/total pages of contents
USB 1 XTICK 2 Page 1/1 1
Page 1/1
00:00 00:00 00:00 00:00
00:00
Exit
3 M Y M E D I A 5 4 RED Change to a different input. GREEN Move to Movie List or Photo List. YELLOW Change Numbers: Changes the number or thumbnails displayed at a time. BLUE Allows you to mark certain files. EXIT ENERGY SAVING Return to TV viewing. Press the ENERGY SAVING button repeatedly to increase the brightness of your screen (Refer to p. 138).
(For LCD TV: It's available "ENERGY SAVING - Off, Screen Off" only.) 115 NETWORK NETWORK LEGAL NOTICE NETWORK
NETWORK
1 2 3 4 MENU ENTER ENTER Select NETWORK. Select Legal Notice. Check Legal notice. EXIT Return to TV viewing. N E T W O R K 122 IMPORTANT NOTICE RELATING TO NETWORK SERVICE IMPORTANT NOTICE RELATING TO NETWORK SERVICES All content and services accessible through this device belong to third parties and are protected by copyright, patent, trademark and/or other intellectual property laws. Such content and services are provided solely for your personal noncommercial use. You may not use any content or services in a manner that has not been authorized by the content owner or service provider. Without limiting the foregoing, unless expressly authorized by the applicable content owner or service provider, you may not copy, upload, post, transmit, translate, sell, modify, create derivative works, or distribute in any manner or medium any content or services displayed through this device. YOU EXPRESSLY ACKNOWLEDGE AND AGREE THAT THE DEVICE AND ALL THIRD PARTY CONTENT AND SERVICES ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED. LG ELECTRONICS EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDITIONS WITH RESPECT TO ANY CONTENT AND SERVICES, EITHER EXPRESS OR, IMPLIED, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY, OF SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. LG DOES NOT GUARANTEE THE ACCURACY, VALIDITY, TIMELINESS, LEGALITY, OR COMPLETENESS OF ANY CONTENT OR SERVICE MADE AVAILABLE THROUGH THIS DEVICE AND DOES NOT WARRANT THAT THE DEVICE OR SERVICES WILL MEET YOUR REQUIREMENTS, OR THAT OPERATION OF THE DEVICE OR SERVICES WILL BE UNINTERRUPTED OR ERROR-
FREE. UNDER NO CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL LG BE LIABLE, WHETHER IN CONTRACT OR TORT, FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, OR ANY OTHER DAMAGES ARISING OUT OF, ANY INFORMATION CONTAINED IN, OR ANY CONTENT OR SERVICE ACCESSED BY YOU OR ANY THIRD PARTY, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Third party services may be changed, suspended, removed, terminated or interrupted, or access may be disabled at any time, without notice, and LG makes no representation or warranty that any content or service will remain available for any period of time. Content and services are transmitted by third parties by means of networks and transmission facilities over which LG has no control. LG may impose limits on the use of or access to certain services or content, in any case and without notice or liability. LG expressly disclaims any responsibility or liability for any change, interruption, disabling, removal of or suspension of any content or service made available through this device. LG is neither responsible nor liable for customer service related to the content and services. Any question or request for service relating to the content or services should be made directly to the respective content and service providers. N E T W O R K 123 NETCAST NETCAST MENU These services are provided by separate Content Provider. Please visit the content providers web site for specific information on their services. (But, some content manual maybe not provide depending on Content Provider). NETCAST menu can differ by country. What is a NETCAST?
Stream movies, TV shows and video, and get up to the minute news, stock information and weather updates directly to your TV using Yahoo!, Netflix, YouTube and Vudu. 1 2 Select NETCAST menu option. ENTER Enjoy Yahoo!, NETFLIX, Vudu, Picasa, or YouTube. N E T C A S T 125 NETCAST YAHOO! TV WIDGETS You can enjoy the best of the Internet in perfect harmony with the simplicity and reliability of your TV. Yahoo! TV Widgets provide an integrated Internet TV experience powered by the Yahoo! Connected TV platform. You can monitor financial stocks, share photos with friends and family, track news and weather and much more, all through the Yahoo! TV Widgets service on your TV. Note that these services are provided by the Content Provider, using Yahoo! Widget Platform provided by Yahoo!. All the services are dependent on appropriate Content Provider. Please check about page of each widgets for Terms of service. Note If you have any question or need any help for the widgets which is not covered in this manual, please contact web site for further help which shall be listed in about page of each widget, or Yahoo!
help site http://conntectedtv.yahoo.com/help. What is a TV Widget?
A TV Widget is an Internet application designed to run on your TV. What is a Snippet?
A Snippet is a shortcut used to open a TV Widget, as a dynamic bookmark to TV Widget content. Using the Remote Control When Yahoo! TV Widgets are displayed, you can use the following remote control buttons. Begin using Yahoo! TV Widgets. Press it again to go back to just watching TV. Highlight and focus on buttons in the Yahoo! TV Widgets user interface. Move the focus selection up. ENTER Select the focused item. MENU RED Go to the TV Menu. Close the open widget and return to watching TV. Move the focus selection down. GREEN Change the open widgets settings. Move the focus selection to the left. YELLOW Add, move, or delete your snippets. Move the focus selection to the right. BLUE Resize the video to fit onscreen, or to make it fullscreen. Getting Started Out of the Box Once your television is powered up and your network is operational, the Yahoo! TV Widgets software guides you through its step-by-step on-screen wizard the first time you startup. These setup steps are designed to provide you with the information and settings youll need to start using the Yahoo! TV Widgets user interface. N E T C A S T 126 Dynamic Contrast
Adjusts the contrast to keep it at the best level according to the brightness of the screen. The picture is improved by making bright parts brighter and dark parts darker. Dynamic Color
Adjusts screen colors so that they look livelier, richer and clearer. This fea-
ture enhances hue, saturation and luminance so that red, blue, green and white look more vivid. Skin Color
(For LED LCD TV, LCD TV)
It detects the skin area of video and adjusts it to express a natural skin color. Noise Reduction
Reduces screen noise without compromising video quality. Digital Noise Reduction Gamma
(Advanced Control Low, Medium, High Expert Control 1.9, 2.2, 2.4) Black Level
Removes noise caused by compressing video.
You can adjust brightness of dark areas and middle gray level areas of the picture. Low or 1.9 : Make brighter and middle gray level areas of the picture brighter. Medium or 2.2 : Express original picture levels. High or 2.4: Make dark and middle gray level areas of the picture darker. Low: The reflection of the screen gets darker. High: The reflection of the screen gets brighter.
Set black level of the screen to proper level.
This function is available in the following modes: AV (NTSC-M), HDMI or Component. Clear White
Make the white area of screen brighter and more white. Eye Care
(For LED LCD TV, LCD TV) Real Cinema or Film Mode
Adjust the brightness of the screen to prevent the screen from being too bright. Dims extremely bright pictures.
This feature is disabled in Picture Mode-Vivid, Cinema, Intelligent Sensor
(For LED LCD TV/LCD TV).
Makes video clips recorded in film look more natural by eliminating judder effect.
DVD and Blu-ray movies are filmed at 24 frames per second (fps). With LG Real Cinema, every frame is consistently processed 5 times in 1/24 of a second producing 120 fps with TruMotion or 2 times in 1/24 of a second producing 48 fps without TruMotion, thus totally eliminating the judder effect.
This function can also work when TruMotion is off. Advanced Control Standard: Displays standard set of colors. Wide: Increase number of colors used.
Maximize the utilization of colors to increase color quality. Color Gamut Expert Control
Displays color domain of the signal. P I C T U R E C O N T R O L 143 PICTURE CONTROL Edge Enhancer
(For LED LCD TV, LCD TV)
Show clearer and distinctive yet natural edges in the video.
This function is enabled in "Picture mode - Cinema, Expert". xvYCC
*This feature is not available for all models.
This is produces richer colors.
This feature represents rich color as much as conventional video signal.
This function is enabled in "Picture mode - Cinema, Expert" when a xvYCC signal is inputted through HDMI. Color Filter
This function filters specific colors in the video. You can use the RGB filter to set color saturation and hue accurately. Expert Pattern
This is a pattern used for expert adjustment.
This function is enabled in "Picture mode - Expert" when you watch DTV. Color Temperature
Adjusts the overall color of the screen by changing the white baseline. a. Method : 2 Points
- Pattern: Inner, Outer
- Red/Green/Blue Contrast, Red/Green/Blue Brightness:
The adjustment range is -50 - +50. LED LCD TV, LCD TV b. Method : 10 Point IRE
- Pattern: Inner, Outer
- IRE (Institute of Radio Engineers) is the unit to display the size of the video signal and can be set among 10, 20, 30 - 100. You can adjust Red, Green or Blue according to each setting.
- Luminance: This function displays calculated luminance value for 2.2 gamma. You can input luminance value you want at 100 IRE, then the target luminance value for 2.2 gamma is displayed at every 10 steps from 10 IRE to 90 IRE.
- Red/Green/Blue: The adjustment range is -50 - +50. Plasma TV b. Method : 20 Point IRE
- IRE (Institute of Radio Engineers) is the unit to display the size of the video signal and can be set among 5, 10, 15 - 100 Plasma TV. You can adjust Red, Green or Blue according to each setting.
- Red/Green/Blue: The adjustment range is -50 - +50. Color Management System
A tool used by the experts to make adjustments by using the test patterns, this does not affect other colors but can be used to selectively adjust the 6 color areas (Red/Green/Blue/Cyan/Mgt/Yellow). Color difference may not be distinctive even when you make the adjust-
ments for the general video. Adjusts Red/Green/Blue/Yellow/Cyan, Magenta.
- Red/Green/Blue/Yellow/Cyan, Magenta Color: The adjustment range is
-30 - +30.
- Red/Green/Blue/Yellow/Cyan, Magenta Tint: The adjustment range is -30
- +30.
- This feature is disabled in RGB-PC and HDMI-PC mode. OPC
*This feature is not available for all models.
Reduces power consumption while keeping brightness and contrast. P I C T U R E C O N T R O L 144 APPENDIX TROUBLESHOOTING Abnormal Operation The remote control doesnt work
Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV.
Ensure that the batteries are installed with correct polarity (+ to +, - to -).
Ensure that the correct remote operating mode is set: TV, VCR etc.
Install new batteries.
*This feature is not available for all models. TV turns off suddenly
Is the sleep timer set?
Check the power control settings. Power interrupted.
If there is no signal, the TV turns off automatically in 15 minutes. Video Problems No picture &No sound
Check whether the product is turned on.
Try another channel. The problem may be with the broadcast.
Is the power cord inserted into wall power outlet?
Check your antenna direction and/or location.
Test the wall power outlet, plug another products power cord into the outlet where the products power cord was plugged in. Picture appears slowly after switching on
This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. No or poor color or poor picture
Adjust Color in menu option.
Keep a sufficient distance between the product and the VCR.
Try another channel. The problem may be with the broadcast.
Are the video cables installed properly?
Activate any function to restore the brightness of the picture. Horizontal/vertical bars
Check for local interference such as an electrical appliance or power or picture shaking tool. Poor reception on some channels Lines or streaks in pic-
tures No picture when con-
necting HDMI
Station or cable product experiencing problems, tune to another station.
Station signal is weak, reorient antenna to receive weaker station.
Check for sources of possible interference.
Check antenna (Change the direction of the antenna).
Check HDMI cable over version 1.3. The HDMI cables dont support HDMI version 1.3, it cause flickers or no screen display. In this case use the latest cables that support HDMI ver-
sion 1.3. A P P E N D I X 179 APPENDIX Audio Problems No output from one of the speakers Unusual sound from inside the product No sound when connecting HDMI/USB PC Mode Problems
Adjust Balance in menu option.
A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product.
Check HDMI cable over version 1.3.
Check USB cable over version 2.0.
Use normal MP3 file.
*This feature is not available for all models. The signal is out of range
Adjust resolution, horizontal frequency, or vertical frequency on the PC.
Check the input source. Vertical bar or stripe on background &
Horizontal Noise &
Incorrect position
Activate the Auto configure feature or adjust size, phase, or H/V position.
(Option) Screen color is unsta-
ble or single color
Check the signal cable.
Reinstall the PC video card. When connecting the HDMI cable to the PC, there is no audio.
Check the manual for the video card in the PC to see if it supports HDMI audio and how to set it up properly. A P P E N D I X 180 Movie List Problems The file does not appear on the Movie
Check whether the file extension is supported. List. Message is displayed saying This file is invalid or the audio is working normally but the video is not work-
ing normally. Message is displayed saying Unsupported Audio or the video is working normally but the audio is not work-
ing normally. Subtitle is not working.
Check whether the file is playing normally on a PC. (Check whether the file is damaged.)
Check whether the resolution is supported.
Check whether the video/audio codec is supported.
Check whether the frame rate is supported.
Check whether the file is playing normally on a PC. (Check whether the file is damaged.)
Check whether the audio codec is supported.
Check whether the bit rate is supported.
Check whether the sample rate is supported.
Check whether the file is playing normally on a PC. (Check whether the file is damaged.)
Check whether the video file and subtitle file name are the same.
Check whether the video file and subtitle file are located in the same folder.
Check whether the subtitle file is supported.
Check whether the language is supported. (When you open the subtitle file on a PC, you can check the language of the subtitle file.) Yahoo! TV Widgets Problems i w i t h n W d g e t i L a n g u a g e d s p a y e d i l i M s c
C a p t i o n
, Did the customer change Menu lan-
guage but Widget did not change its language.
Some Widgets do not fully support TV Menu options.
The help site for individual widget can be found in the settings panel of each widget by pressing the GREEN button on your remote after opening that widget from the Dock. A P P E N D I X 181 APPENDIX Yahoo! TV Widgets Problems Was the customer watching HDMI input?
If customer uses HDMI with Simplink ON, the WIDGETS button is blocked.
To use Yahoo! TV Widgets while using the HDMI input, turn off Simplink-on in the OPTION menu. Or change to another Input and press then press the WIDGETS button. Was the customer watching My Media?
Did the customer see Starting Yahoo! TV Widgets remain and TV Widget not dis-
played?
The WIDGETS button is blocked when using MY MEDIA.
Exit MY MEDIA by pressing the NETCAST button and then select Yahoo!
Press the NETCAST button and then select NETFLIX. Then press the WIDGETS button to enter Yahoo! TV Widgets. This re-starts Yahoo! TV Widgets. Nothing happens when pressing WIDGETS button
Turn off the TV and then turn it back on. Press the NETCAST button and then the BLUE button. Select Restore Yahoo!
Factory Settings to restore the Yahoo! Factory Settings.
For more help, visit the Yahoo! help site: http://connectedtv.yahoo. com/help. Is Loading mes-
sage displayed?
Check IP Address setting is OK?
Is Connection Unavailable icon (yel-
low triangle) dis-
played on snippet?
Some Widgets work properly while other s do not.
If the Loading message does not go away after a reasonable amount of time, delete that widget and re-install it.
Make sure the TV can connect to the internet.
If connection unavailable icon is displayed, the server may under maintenance or unreachable for other reasons. Try again later or visit the Yahoo! help site. http://connectedtv.yahoo.com/help
Try again later.
Try re-installing the Widget. Delete that widget by pressing the Yellow button when it's highlighted in the dock. Then press the Red button twice to delete that widget. Then open the Widget Gallery and browse to find that widget and select Add Widget to My Profile to install that widget and then try again.
If problem still exists, restore Yahoo! factory settings by pressing NETCAST button and BLUE button on your remote control. F a i l e d t o l a u n c h Y a h o o
T V W d g e t s i F a i l e d t o o p e n s o m e w d g e t s i A P P E N D I X 182 Yahoo! TV Widgets Problems i W d g e t i s s t u c k i f t h e r e m o t e c o n t r o l b u t t o n i s p r e s s e d
. i w d g e t f r o m g a l l e r y G a l l e r y
U n a b e t o i n s t a l l l i s a g e d s p a y e d l i a n y t h n g t o d s p a y i l m e s
F l i c k r
l W e c o u d n o t f i n d Press BACK button and try again later.
The error may only be temporary. Exit out and try again. Check IP Address
If not, connect Network Cable properly and set IP address from setting is OK?
Network menu and try again or contact Internet service provider. Press RED or WIDGETS button on remote control. Press NETCAST but-
ton.
Exits Yahoo! TV Widgets by pressing RED button on your remote and re-enter by WIDGETS button.
Exits Yahoo! TV Widgets by pressing NETCAST button and enter NETFLIX temporarily, and re-enter Yahoo! Widgets by pressing NETCAST button and select Yahoo!
If the problem still exists, re-install the Widget. Press the Yellow button with the Widget highlighted in the Dock. Press the Red button twice to delete that widget. Now open the Widget Gallery and browse to find that widget and select Add Widget to My Profile to install that widget and then try again.
If the problem still exists for all widgets, restore the Yahoo! Factory settings by pressing the NETCAST button and the Blue button on your remote control. Select Restore Yahoo! Factory Settings to reset. Check IP Address
If not, connect Network Cable properly and set IP address from setting is OK?
menu-Option and try again or contact Internet service provider. Is Lock Icon on right side of Add Widget to My Profile?
Install completed but it never worked. Is connection unavailable icon
(yellow triangle) displayed?
Need Owner PIN to install. If you forgot Owner PIN, contact Yahoo!
for further help. http://connectedtv.yahoo.com/help
Try to re-start Yahoo! TV Widgets after you enter MY MEDIA and exit from MY MEDIA.
Or Delete it and re-install it.
If yes, check network settings or contact internet service provider, or try later. Did you sign-in Yahoo! account?
If yes, you need to upload your photos to Flickr site to display.
If not, try again later. The Flickr server may be under mainte-
nance, or contact service provider. A P P E N D I X 183 APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1 Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. 2 Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
Please be sure not to use a wet cloth. Extended Absence CAUTION
If you expect to leave your TV dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges. A P P E N D I X 184 APPENDIX MODELS 42LE5400
(42LE5400-UC) 42LE5500
(42LE5500-UA) 47LE5400
(47LE5400-UC) 47LE5500
(47LE5500-UA) Dimensions
(Width x Height x Depth) With stand 1016.0 mm x 692.0 mm x 270.0 mm 1126.6 mm x 757.9 mm x 284.4 mm
(40.0 inch x 27.2 inch x 10.6 inch)
(44.3 inch x 29.8 inch x 11.1 inch) Without stand 1016.0 mm x 630.0 mm x 29.3 mm 1126.6 mm x 692.0 mm x 29.3 mm
(40.0 inch x 24.8 inch x 1.1 inch)
(44.3 inch x 27.2 inch x 1.1 inch) Weight With stand Without stand 19.5 kg (42.9 lbs) 16.7 kg (36.8 lbs) 22.6 kg (49.8 lbs) 19.6 kg (43.2 lbs) MODELS Dimensions
(Width x Height x Depth) With stand Without stand Weight With stand Without stand Power requirement Television System Program Coverage External Antenna Impedance Environment condition Operating Temperature Operating Humidity Storage Temperature Storage Humidity A P P E N D I X 55LE5400
(55LE5400-UC) 55LE5500
(55LE5500-UA) 1306.0 mm x 867.0 mm x 345.0 mm
(51.4 inch x 34.1 inch x 13.5 inch) 1306.0 mm x 797.0 mm x 30.7 mm
(51.4 inch x 31.3 inch x 1.2 inch) 34.5 kg (76.0 lbs) 28.8 kg (63.4 lbs) AC 120 V ~ 50 / 60 Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 0 to 40C (32 to 104F) Less than 80%
-20 to 60C (-4 to 140F) Less than 85%
The specifications shown above may be changed without prior notice for quality improvement. 188 MODELS 42LE7500
(42LE7500-UC) 47LE7500
(47LE7500-UC) Dimensions
(Width x Height x Depth) With stand 1018.2 mm x 693.5 mm x 269.8 mm 1128.6 mm x 758.9 mm x 284.4 mm
(40.0 inch x 27.3 inch x 10.6 inch)
(44.4 inch x 29.8 inch x 11.1 inch) Without stand 1018.2 mm x 630.7 mm x 29.3 mm 1128.6 mm x 693.3 mm x 29.8 mm
(40.0 inch x 24.8 inch x 1.1 inch)
(44.4 inch x 27.2 inch x 1.1 inch) Weight With stand 21.9 kg (48.2 lbs) Without stand 19.1 kg (42.1 lbs) 26.2 kg (57.7 lbs) 23.0 kg (50.7 lbs) MODELS Dimensions
(Width x Height x Depth) With stand Without stand Weight With stand Without stand 55LE7500
(55LE7500-UC) 1306.0 mm x 867.7 mm x 328.0 mm
(51.4 inch x 34.1 inch x 12.9 inch) 1306.0 mm x 797.4 mm x 31.2 mm
(51.4 inch x 31.3 inch x 1.2 inch) 38.4 kg (84.6 lbs) 32.8 kg (72.3 lbs) MODELS 47LE8500
(47LE8500-UA) 55LE8500
(55LE8500-UA) Dimensions
(Width x Height x Depth) With stand Without stand 1122.6 mm x 768.3 mm x 275.0 mm
(44.1 inch x 30.2 inch x 10.8 inch) 1292.6 mm x 874.4 mm x 311.9 mm
(50.8 inch x 34.4 inch x 12.2 inch) 1122.6 x 707.3 x 24.5 (max 39.7) mm
(44.1 x 27.8 x 0.9 (max 1.5) inches) 1292.6 mm x 802.9 mm x 24.5 mm (max 39.7 mm)
(50.8 inch x 31.6 inch x 0.9 inch (max 1.5 inch)) Weight With stand 31.6 kg (69.6 lbs) Without stand 26.9 kg (59.3 lbs) 43.8 kg (96.5 lbs) 35.8 kg (78.9 lbs) Power requirement Television System Program Coverage External Antenna Impedance Environment condition Operating Temperature Operating Humidity Storage Temperature Storage Humidity AC 120 V ~ 50 / 60 Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 0 to 40C (32 to 104F) Less than 80%
-20 to 60C (-4 to 140F) Less than 85%
The specifications shown above may be changed without prior notice for quality improvement. A P P E N D I X 189 APPENDIX IR CODES 1. How to Connect
Connect your wired remote control to the Remote Control port on the TV. 2. Remote Control IR Codes
Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz Tc T1 Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3
Configuration of frame 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Repeat frame
Lead code
Repeat code
Bit description Bit 0 Repeat code Tf 9 ms 4.5 ms 9 ms 2.25 ms 0.55 ms Bit 1 0.56ms 1.12 ms 0.56ms 2.24ms
Frame interval: Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz A P P E N D I X 190 Code
(Hexa) 00 01 02 03 06 07 08 09 0B 0F 10-19 1A 1E 28 30 40 41 43 44 45 4C 5B 58 59 61 63 71 72 79 7E 8E 8F 95 Function Note CH CH VOL +
VOL -
Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button
(Power On/Off) MUTE/DELETE Remote Control Button Remote Control Button INPUT TV Remote Control Button Remote Control Button Number Key 0-9 FLASHBK FAV/MARK BACK Remote Control Button Remote Control Button Remote Control Button AV MODE
MENU ENTER Q.MENU
- (Dash)/LIST EXIT WIDGETS NETCAST BLUE YELLOW GREEN RED RATIO SIMPLINK
Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button Remote Control Button
ENERGY SAVING Remote Control Button Remote Control Button AA INFO Remote Control Button Code
(Hexa) B0 B1 BA D6 C4 C5 5A D0 BF D4 D5 CE CC E9 DA 76 77 AF Function Note
TV Remote Control Button Remote Control Button Remote Control Button Discrete IR Code
(TV Input Selection) POWER ON Discrete IR Code POWER OFF AV1 AV2
(Only Power On) Discrete IR Code
(Only Power Off) Discrete IR Code
(AV1 Input Selection) Discrete IR Code
(AV2 Input Selection) COMPONENT1 Discrete IR Code
(Component1 Input Selection) COMPONENT2 Discrete IR Code
(Component2 Input Selection) RGB-PC Discrete IR Code HDMI1 HDMI2 HDMI3 HDMI4 Ratio 4:3 Ratio 16:9 Ratio Zoom
(RGB-PC Input Selection) Discrete IR Code
(HDMI1 Input Selection) Discrete IR Code
(HDMI2 Input Selection) Discrete IR Code
(HDMI3 Input Selection) Discrete IR Code
(HDMI4 Input Selection) Discrete IR Code
(Only 4:3 Mode) Discrete IR Code
(Only 16:9 Mode) Discrete IR Code
(Only Zoom Mode) A P P E N D I X 191 APPENDIX OPEN SOURCE LICENSE GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim cop-
ies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your free-
dom to share and change free software - to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other free software foundation software is cov-
ered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to free-
dom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute cop-
ies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to sur-
render the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the soft-
ware, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the origi-
nal authors' reputations. Finally, any free program is threatened constantly by soft-
ware patents. We wish to avoid the danger that redistribu-
tors of a free program will individually obtain patent licens-
es, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This license applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program"
means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modi-
fications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as
"you". Activities other than copying, distribution and modifica-
tion are not covered by this license; they are outside its scope. The act of running the Program is not restricted, and the output from the program is covered only if its contents constitute a work based on the program (inde-
pendent of having been made by running the program). Whether that is true depends on what the program does. 1. You may copy and distribute verbatim copies of the program's source code as you receive it, in any medium, provided that you conspicuously and appropriately pub-
lish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty;
and give any other recipients of the program a copy of this license along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty pro-
tection in exchange for a fee. 2. You may modify your copy or copies of the program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. A P P E N D I X 192 b) You must cause any work that you distribute or pub-
lish, that in whole or in part contains or is derived from the Program or any part there of, to be licensed as a whole at no charge to all third parties under the terms of this license. c) If the modified program normally reads commands interactively when run, you must cause it, when start-
ed running for such interactive use in the most ordi-
nary way, to print or display an announcement includ-
ing an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the pro-
gram under these conditions, and telling the user how to view a copy of this license. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably con-
sidered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distri-
bution of the whole must be on the terms of this license, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribu-
tion of derivative or collective works based on the pro-
gram. In addition, mere aggregation of another work not based on the program with the Program (or with a work based on the program) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. 3. You may copy and distribute the program (or a work based on it, under section 2) in object code or execut-
able form under the terms of sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be dis-
tributed under the terms of sections 1 and 2 above on a medium customarily used for software inter-
change; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange;
or, c) Accompany it with the information you received as to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an execut-
able work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major compo-
nents (compiler, kernel, and so on) of the operating system on which the executable runs, unless that com-
ponent itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this license. However, par-
ties who have received copies, or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the program (or any work based on the program), you indicate your acceptance of this license to do so, and all its terms and conditions for copying, distributing or modifying the program or works based on it. 6. Each time you redistribute the program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restric-
tions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this license. A P P E N D I X 193 APPENDIX 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not lim-
ited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distrib-
ute the program at all. For example, if a patent license would not permit royalty-free redistribution of the pro-
gram by all those who receive copies directly or indi-
rectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the program. If any portion of this section is held invalid or unenforce-
able under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free soft-
ware distribution system, which is implemented by pub-
lic license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent applica-
tion of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 8. If the distribution and/or use of the program is restrict-
ed in certain countries either by patents or by copy-
righted interfaces, the original copyright holder who places the program under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. 9. The Free Software Foundation may publish revised and/
or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the program specifies a version number of this license which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the program does not specify a version number of this license, you may choose any ver-
sion ever published by the Free Software Foundation. 10.If you wish to incorporate parts of the program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
"AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT IMPLIED WARRANTIES OF LIMITED TO, THE MERCHANTABILITY AND FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. FITNESS 12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. A P P E N D I X 194 END OF TERMS AND CONDITIONS How to apply these terms to your new programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redis-
tribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. one line to give the program's name and a brief idea of what it does. Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/
or modify it under the terms of the GNU General Public License as published by the Free Software Foundation;
either version 2 of the license, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY;
for details type show w. This is free software, and you are welcome to redistribute it under certain conditions; type show c for details. The hypothetical commands show w and show c should show the appropriate parts of the General Public License. Of course, the commands you use may be called some-
thing other than show w and show c; they could even be mouse-clicks or menu items-whatever suits your program. You should also get your employer (if you work as a pro-
grammer) or your school, if any, to sign a copyright dis-
claimer for the program, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program Gnomovision (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this license. A P P E N D I X 195 APPENDIX GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim cop-
ies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]
Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages - typically libraries - of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strat-
egy to use in any particular case, based on the explana-
tions below. When we speak of free software, we are referring to free-
dom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to dis-
tribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copy-
right the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or mod-
ify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the exis-
tence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free pro-
gram by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain des-
ignated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-
free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the origi-
nal library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over com-
peting non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advan-
tages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-
free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. A P P E N D I X 196 Although the Lesser General Public License is Less protec-
tive of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified ver-
sion of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the differ-
ence between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run. GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This license agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called this license). Each license is addressed as "you". A library means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The Library, below, refers to any such software library or work which has been distributed under these terms. A work based on the Library means either the Library or any derivative work under copyright law: that is to say, a work containing the library or a portion of it, either verba-
tim or with modifications and/or translated straightfor-
wardly into another language. (Hereinafter, translation is included without limitation in the term modification.) Source code for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface defi-
nition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modifica-
tion are not covered by this license; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the library does and what the program that uses the library does. 1. You may copy and distribute verbatim copies of the library's complete source code as you receive it, in any medium, provided that you conspicuously and appropri-
ately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and distribute a copy of this license along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty pro-
tection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions:
a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this license. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argu-
ment passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs what-
ever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined indepen-
dent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the library, and can be reasonably consid-
ered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the library, the distribu-
tion of the whole must be on the terms of this license, whose permissions for other licenses extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribu-
tion of derivative or collective works based on the library. In addition, mere aggregation of another work not based on the library with the library (or with a work based on the library) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. A P P E N D I X 197 APPENDIX 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irrevers-
ible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the library into a program that is not a library. 4. You may copy and distribute the library (or a portion or derivative of it, under Section 2) in object code or exe-
cutable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete cor-
responding machine-readable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software inter-
change. If distribution of object code is made by offering access to copy from a designated place, then offering equiva-
lent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a work that uses the Library. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this license. However, linking a work that uses the library with the Library creates an executable that is a derivative of the Library (because it contains portions of the library), rather than a work that uses the library. The executable is therefore covered by this license. Section 6 states terms for distribution of such executable. When a work that uses the library uses material from a header file that is part of the library, the object code for the work may be a derivative work of the library even though the source code is not. Whether this is true is especially significant if the work can be linked without the library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessories, and small mac-
ros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work.
(Executable containing this object code plus portions of A P P E N D I X 198 the library will still fall under Section 6.) Otherwise, if the work is a derivative of the library, you may distribute the object code for the work under the terms of Section 6. Any executable containing that work also fall under Section 6, whether or not they are linked directly with the library itself. 6. As an exception to the sections above, you may also combine or link a "work that uses the library" with the library to produce a work containing portions of the library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engi-
neering for debugging such modifications. You must give prominent notice with each copy of the work that the library is used in it and that the Library and its use are covered by this license. You must supply a copy of this license. If the work during execution dis-
plays copyright notices, you must include the copyright notice for the library among them, as well as a reference directing the user to the copy of this license. Also, you must do one of these things:
a) Accompany the work with the complete correspond-
ing machine-readable source code for the library including whatever changes were used in the work
(which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable work that uses the Library, as object code and/or source code, so that the user can modify the library and then relink to produce a modified executable containing the modified library. (It is understood that the user who changes the contents of definitions files in the library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the users computer system, rather than copying library functions into the executable, and (2) will oper-
ate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the "work that uses the library" must include any data and utility pro-
grams needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the library together in an executable that you distribute. 7. You may place library facilities that are a work based on the library side-by-side in a single library together with other library facilities not covered by this license, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or dis-
tribute the library except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the library is void, and will automatically terminate your rights under this license. However, parties who have received copies, or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to modify or distribute the library or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the library (or any work based on the library), you indicate your acceptance of this license to do so, and all its terms and conditions for copying, distribut-
ing or modifying the library or works based on it. 10.Each time you redistribute the library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this license. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not lim-
ited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distrib-
ute the library at all. For example, if a patent license would not permit royalty-free redistribution of the library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distri-
bution of the library. If any portion of this section is held invalid or unenforce-
able under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free soft-
ware distribution system which is implemented by pub-
lic license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent applica-
tion of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a license cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 12.If the distribution and/or use of the library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the library under this license may add an explicit geograph-
ical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. 13.The Free Software Foundation may publish revised and/
or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the library specifies a version number of this license which applies to it and any later version, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. A P P E N D I X 199 APPENDIX it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of war-
ranty; and each file should have at least the copyright line and a pointer to where the full notice is found. one line to give the library's name and a brief idea of what it does. Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the license, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a pro-
grammer) or your school, if any, to sign a copyright dis-
claimer for the library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library Frob (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice If the library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14.If you wish to incorporate parts of the library into other free programs whose distribution conditions are incom-
patible with these, write to the author to ask for permis-
sion. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserv-
ing the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. END OF TERMS AND CONDITIONS How to apply these terms to your new libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making A P P E N D I X 200 MOZILLA PUBLIC LICENSE Version 1.1
1.Definitions. 1.0.1. Commercial use means distribution or otherwise making the covered code available to a third party. Contributor means each entity that creates or con-
tributes to the creation of modifications. which, at the time of its release under this license is not already covered code governed by this license. 1.10.1. Patent claims means any patent claim(s), now owned or hereafter acquired, including without limi-
tation, method, process, and apparatus claims, in any patent licensable by grantor. Contributor version means the combination of the original code, prior modifications used by a contribu-
tor, and the modifications made by that particular contributor. 1.11. Covered code means the original code or modifi-
cations or the combination of the original code and modifications, in each case including portions there-
of. Electronic distribution mechanism means a mech-
anism generally accepted in the software develop-
ment community for the electronic transfer of data. 1.12. Executable means covered code in any form other than source code. Initial developer means the individual or entity identified as the initial Developer in the Source Code notice required by exhibit A. Larger work means a work which combines covered code or portions thereof with code not governed by the terms of this License. Source code means the preferred form of the cov-
ered code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an executable, or source code dif-
ferential comparisons against either the original code or another well known, available covered code of the contributor's choice. The source code can be in a compressed or archival form, provided the appropri-
ate decompression or de-archiving software is wide-
ly available for no charge. You (or Your) means an individual or a legal entity exercising rights under, and complying with all of the terms of, this license or a future version of this license issued under section 6.1. For legal entities, You includes any entity which controls, is controlled by, or is under common control with You. For purposes of this definition, control means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or ben-
eficial ownership of such entity. 1.1. 1.2. 1.3. 1.4. 1.5. 1.6. 1.7. 1.8. License means this document. 2. Source Code License. 1.8.1. Licensable means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein. 2.1. The initial developer grant. The initial developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims:
1.9. Modifications means any addition to or deletion from the substance or structure of either the original code or any previous modifications. When covered code is released as a series of files, a modification is:
A. Any addition to or deletion from the contents of a file containing original code or previous modifica-
tions. B. Any new file that contains any part of the original code or previous modifications. 1.10. Original code means source code of computer software code which is described in the source code notice required by exhibit as original code, and a) under intellectual property rights (other than pat-
ent or trademark) licensable by initial developer to use, reproduce, modify, display, perform, subli-
cense and distribute the original code (or portions thereof) with or without modifications, and/or as part of a larger work; and
(b) under patents claims infringed by the making, using or selling of original code, to make, have made, use, practice, sell, and offer for sale, and/
or otherwise dispose of the original code (or por-
tions there of). A P P E N D I X 201 APPENDIX
(c) the licenses granted in this section 2.1(a) and (b) are effective on the date Initial developer first distributes original code under the terms of this license.
(d) Notwithstanding section 2.1(b) above, no patent license is granted: 1) for code that You delete from the original Code; 2) separate from the original code; or 3) for infringements caused by:
i) the modification of the original code or ii) the combination of the original code with other soft-
ware or devices. 2.2. Contributor Grant. Subject to third party intellectual property claims, each contributor hereby grants You a world-wide, royalty-free, non-exclusive license
(a) under intellectual property rights (other than pat-
ent or trademark) licensable by contributor, to use, reproduce, modify, display, perform, subli-
cense and distribute the modifications created by such contributor (or portions thereof) either on an unmodified basis, with other modifications, as covered code and/or as part of a larger work; and
(b) under patent claims infringed by the making, using, or selling of modifications made by that contributor either alone and/or in combination with its contributor version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) modi-
fications made by that contributor (or portions thereof); and 2) the combination of modifications made by that contributor with its contributor ver-
sion (or portions of such combination).
(c) the licenses granted in sections 2.2(a) and 2.2(b) are effective on the date contributor first makes commercial use of the covered code.
(d) Notwithstanding section 2.2(b) above, no patent license is granted: 1) for any code that contributor has deleted from the contributor version; 2) separate from the contributor version; 3) for infringements caused by: i) third party modifica-
tions of contributor version or ii) the combination of modifications made by that contributor with other software (except as part of the contributor version) or other devices; or 4) under patent claims infringed by covered code in the absence of modifications made by that contributor. 3. Distribution Obligations. 3.1. Application of license. The modifications which You create or to which you contribute are governed by the terms of this license, including without limitation section 2.2. The source code version of covered code may be distributed only under the terms of this license or a future ver-
sion of this license released under section 6.1, and you must include a copy of this license with every copy of the source code you distribute. You may not A P P E N D I X 202 offer or impose any terms on any source code ver-
sion that alters or restricts the applicable version of this license or the recipients' rights hereunder. However, you may include an additional document offering the additional rights described in section 3.5. 3.2. Availability of source code. Any modification which you create or to which you contribute must be made available in source code form under the terms of this license either on the same media as an executable version or via an accepted electronic distribution mechanism to any-
one to whom you made an executable version avail-
able; and if made available via electronic distribution mechanism, must remain available for at least twelve
(12) months after the date it initially became avail-
able, or at least six (6) months after a subsequent version of that particular modification has been made available to such recipients. You are responsi-
ble for ensuring that the source code version remains available even if the electronic distribution mecha-
nism is maintained by a third party. 3.3. Description of modifications. You must cause all covered code to which you contrib-
ute to contain a file documenting the changes You made to create that covered code and the date of any change. You must include a prominent statement that the modification is derived, directly or indirectly, from original code provided by the initial developer and including the name of the initial developer in (a) the source code, and (b) in any notice in an executable version or related documentation in which you describe the origin or ownership of the covered code. 3.4. Intellectual property matters
(a) Third party claims. If contributor has knowledge that a license under a third party's intellectual property rights is required to exercise the rights granted by such contributor under sections 2.1 or 2.2, contributor must include a text file with the source code distribution titled "LEGAL"
which describes the claim and the party making the claim in sufficient detail that a recipient will know whom to contact. If contributor obtains such knowl-
edge after the modification is made available as described in section 3.2, contributor shall promptly modify the LEGAL file in all copies contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the covered code that new knowledge has been obtained.
(b) Contributor APIs. If contributor's modifications include an application programming interface and contributor has knowl-
edge of patent licenses which are reasonably neces-
sary to implement that API, contributor must also include this information in the LEGAL file.
(c) Representations. contributor represents that, except as disclosed pur-
suant to section 3.4(a) above, contributor believes that contributor's modifications are contributor's original creation(s) and/or contributor has sufficient rights to grant the rights conveyed by this license. 3.5. Required notices. You must duplicate the notice in exhibit A in each file of the source code. If it is not possible to put such notice in a particular source code file due to its struc-
ture, then You must include such notice in a location
(such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more modification(s), you may add your name as a contributor to the notice described in exhibit A. you must also duplicate this license in any documenta-
tion for the source code where You describe recipi-
ents' rights or ownership rights relating to covered code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obliga-
tions to one or more recipients of covered code. However, you may do so only on your own behalf, and not on behalf of the Initial developer or any contribu-
tor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by you alone, and You hereby agree to indemnify the Initial developer and every contributor for any liability incurred by the Initial developer or such contributor as a result of warranty, support, indemnity or liability terms you offer. 3.6. Distribution of executable versions. You may distribute covered code in executable form only if the requirements of section 3.1-3.5 have been met for that covered code, and if you include a notice stating that the source code version of the covered code is available under the terms of this license, including a description of how and where you have fulfilled the obligations of section 3.2. The notice must be conspicuously included in any notice in an executable version, related documentation or collat-
eral in which you describe recipients' rights relating to the covered code. You may distribute the execut-
able version of covered code or ownership rights under a license of your choice, which may contain terms different from this license, provided that you are in compliance with the terms of this license and that the license for the executable version does not attempt to limit or alter the recipient's rights in the source code version from the rights set forth in this license. If you distribute the executable version under a different license you must make it absolutely clear that any terms which differ from this license are offered by you alone, not by the Initial developer or any contributor. You hereby agree to indemnify the initial developer and every contributor for any liability incurred by the initial developer or such contributor as a result of any such terms You offer. 3.7. Larger works. You may create a larger work by combining covered code with other code not governed by the terms of this license and distribute the larger work as a single product. In such a case, you must make sure the requirements of this license are fulfilled for the cov-
ered code. 4. Inability to comply due to statute or regulation. If it is impossible for you to comply with any of the terms of this license with respect to some or all of the covered code due to statute, judicial order, or regulation then you must: (a) comply with the terms of this license to the maximum extent possible; and
(b) describe the limitations and the code they affect. Such description must be included in the LEGAL file described in section 3.4 and must be included with all distributions of the source code. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipi-
ent of ordinary skill to be able to understand it. 5. Application of this license. This license applies to code to which the initial devel-
oper has attached the notice in exhibit A and to related covered code. 6. Versions of the license. 6.1. New versions. Netscape communications corporation (Netscape) may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number. 6.2. Effect of new versions. Once covered code has been published under a particular version of the license, you may always con-
tinue to use it under the terms of that version. You may also choose to use such covered code under the terms of any subsequent version of the license published by netscape. No one other than netscape has the right to modify the terms applicable to cov-
ered code created under this license. 6.3. Derivative works.
"Mozilla",
"MOZILLAPL", If You create or use a modified version of this license
(which you may only do in order to apply it to code which is not already covered code governed by this license), You must (a) rename Your license so that the phrases
"MOZPL",
"Netscape", "MPL", "NPL" or any confusingly similar phrase do not appear in your license (except to note that your license differs from this license) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public license and netscape Public License. (Filling in the name of the initial developer, original code or contributor in the notice described in exhibit A shall not of themselves be deemed to be modifications of this license.) A P P E N D I X 203 APPENDIX 7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN AS IS BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER. 8. TERMINATION. 8.1. This license and the rights granted hereunder will terminate automatically if you fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All subli-
censes to the covered code which are properly granted shall survive any termination of this license. Provisions which, by their nature, must remain in effect beyond the termination of this license shall survive. 8.2. If you initiate litigation by asserting a patent infringe-
ment claim (excluding declatory judgment actions) against initial developer or a contributor (the initial developer or contributor against whom you file such action is referred to as Participant) alleging that:
(a) such participant's contributor version directly or indirectly infringes any patent, then any and all rights granted by such participant to you under sections 2.1 and/or 2.2 of this license shall, upon 60 days notice from Participant terminate pro-
spectively, unless if within 60 days after receipt of notice you either: (i) agree in writing to pay par-
ticipant a mutually agreeable reasonable royalty for your past and future use of modifications made by such participant, or (ii) withdraw your litigation claim with respect to the contributor version against such participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by participant to you under sec-
tions 2.1 and/or 2.2 automatically terminate at the expiration of the 60 day notice period specified above.
(b) any software, hardware, or device, other than such participant's contributor Version, directly or indi-
rectly infringes any patent, then any rights grant-
A P P E N D I X 204 ed to You by such participant under sections 2.1(b) and 2.2(b) are revoked effective as of the date you first made, used, sold, distributed, or had made, modifications made by that partici-
pant. 8.3. If you assert a patent infringement claim against participant alleging that such participant's contribu-
tor version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringe-
ment litigation, then the reasonable value of the licenses granted by such participant under sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license. 8.4. In the event of termination under sections 8.1 or 8.2 above, all end user license agreements (excluding dis-
tributors and resellers) which have been validly granted by you or any distributor hereunder prior to termination shall survive termination. 9. LIMITATION OF LIABILITY. INDIRECT, SPECIAL, UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR ANY INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU. 10. U.S. GOVERNMENT END USERS. The covered code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), con-
sisting of "commercial computer software" and "com-
mercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all U.S. Government end users acquire covered code with only those rights set forth herein. 11. MISCELLANEOUS. This license represents the complete agreement con-
cerning subject matter hereof. If any provision of this license is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise), excluding its conflict-of-law provisions. With respect to dis-
putes in which at least one party is a citizen of, or an entity chartered or registered to do business in the united states of america, any litigation relating to this License shall be subject to the jurisdiction of the federal courts of the northern district of california, with venue lying in santa clara county, california, with the losing party responsible for costs, including with-
out limitation, court costs and reasonable attorneys'
fees and expenses. The application of the united nations convention on contracts for the International sale of goods is expressly excluded. Any law or regu-
lation which provides that the language of a contract shall be construed against the drafter shall not apply to this license. 12. RESPONSIBILITY FOR CLAIMS. As between initial developer and the contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this license and you agree to work with initial developer and contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to constitute any admission of liability. 13. MULTIPLE-LICENSED CODE. Initial developer may designate portions of the cov-
ered code as "Multiple-Licensed". "Multiple-
Licensed" means that the initial developer permits you to utilize portions of the covered code under your choice of the NPL or the alternative licenses, if any, specified by the initial developer in the file described in exhibit A. EXHIBIT A -Mozilla Public License. The contents of this file are subject to the Mozilla Public License Version 1.1 (the license); you may not use this file except in compliance with the License. You may obtain a copy of the license at http://www.mozilla.org/MPL/
Software distributed under the license is distributed on an
"AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the license for the specific lan-
guage governing rights and limitations under the License. The Original Code is ______________________________________
. Initial Developer of The is___________________. Portions created by ______________________ are Copyright
(C) _______________________. All Rights Reserved. the Original Code Contributor(s): ______________________________________. Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in which case the provisions of [______] license are applicable instead of those above. If you wish to allow use of your version of this file only under the terms of the [____] license and not to allow others to use your version of this file under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provi-
sions required by the [___] license. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] license."
NOTE: The text of this exhibit A may differ slightly from the text of the notices in the source code files of the original code. You should use the text of this exhibit A rather than the text found in the original code/source code for Your modifications. A P P E N D I X 205 The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service. MODEL SERIAL Regulatory Information cont. FCC Compliance Statement This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. CE Conformity Notice (for Europe) Products with the CE Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive
(73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms :
EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 EN 60950-1
; Radio Frequency Interference
; Electromagnetic Immunity
; Power Line Harmonics
; Voltage Fluctuations
; Product Safety NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. TCO'99 (TCO'99 applied model only) Congratulations!
You have just purchased a TCO99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. 01 Regulatory Information cont. Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Electronic equipment in offices is often left running continuously, resulting in unnecessary consumption of large amounts of energy and additional power generation. From the standpoint of carbon dioxide emissions alone, it is vital to save energy. What does labelling involve?
The product meets the requirements for the TCO99 scheme which provides for international and environmental labelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen
(The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues:
ecology, ergonomics, emission of electrical and magnetical fields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, and other substances. The product must be prepared for recycling and the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered. Energy requirements include a demand that the system unit and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the system unit shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electrical and magnetical fields as well as work load and visual ergonomics. Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Developments website http://www.tcodevelopment.com or may be ordered from:
TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 Email : development@tco.se Information regarding TCO99 approved and labelled products may also be obtained at http://www.tcodevelopment.com Ecological requirements Flame retardants Flame retardants may be present in printed wiring board laminates, cables, and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30%
by weight of the plastic in a computer casing can consist of flame retardant substances. Many flame retardants contain bromine or chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls). Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects, including reproductive damage in fish-
eating birds and mammals, due to the bio-accumulative*
processes when not disposed of in accordance with strict standards for disposal. TCO99 requires that plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives. Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. TCO99 requires that batteries, the colour-generating layers of display screens, and the electrical or electronics components shall not contain any cadmium. Mercury**
Mercury is sometimes found in batteries, relays and switches. TCO99 requires that batteries shall not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one 02 Regulatory Information cont. exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available. Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. TCO99 permits the use of lead due to the lack of commercially available alternatives, but in future requirements TCO Development aims at restricting the use of lead. _____________________________________________
* Bio-accumulative is defined as substances which accumulate in living organisms.
**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative. TCO03 (TCO03 applied model only) Congratulations!
The display you have just purchased carries the TCO03 Displays label. This means that your display is designed,manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO03 Display requirements:
Ergonomics Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy Energy-saving mode after a certain time beneficial both for the user and the environment Electrical safety Emissions Electromagnetic fields 03 Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001 Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, please visit www.tcodevelopment.com English Information for Environmental Preservation LGE. announced the 'LG Declaration for a Cleaner Environment' in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects. We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly. We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our monitors. Information for recycling This monitor may contain parts which could be hazardous to the environment. It is important that this monitor be recycled after use. LGE. handles all waste monitors through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in Regulatory Information cont. operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG. We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our green policies. http://www.lge.com/about/environment/html/Recycling.jsp Deutsch Informationen zur Erhaltung der Umwelt Im Jahr 1994 verkndete LGE die 'LG Declaration for a Cleaner Environment' (LG Erklrung fr eine sauberere Umwelt). Seitdem dient dieses Ideal als fhrendes Prinzip des Unternehmens. Diese Erklrung war die Basis fr die Durchfhrung von umweltfreundlichen Aktivitten, wobei wirtschaftliche, umweltbezogene und soziale Aspekte in die berlegungen mit einbezogen wurden. Wir frdern Aktivitten zum Schutz der Umwelt und die Entwicklung unserer Produkte ist darauf ausgerichtet, unserem Konzept bezglich Umweltfreundlichkeit gerecht zu werden. Wir sind darauf bedacht, den Anteil der in unseren Produkten enthaltenen schdlichen Materialien zu minimieren. So ist in unseren Monitoren beispielsweise kein Kadmium zu finden. Informationen zum Thema Recycling Dieser Monitor enthlt Teile, die umweltschdlich sein knnen. Es ist unbedingt erforderlich, dass der Monitor recycelt wird, nachdem er auer Dienst gestellt wurde. Bei LGE. werden alle ausrangierten Monitore in einem unter umweltbezogenen Aspekten geeigneten Verfahren recycelt. Augenblicklich sind weltweit mehrere Rcknahme- und Recyclingsysteme im Einsatz. Viele Teile werden wieder verwendet und recycelt. Schdliche Substanzen und Schwermetalle werden durch umweltvertrgliche Verfahren behandelt. Falls Sie mehr ber unser Recyclingprogramm erfahren mchten, wenden Sie sich bitte an Ihren lokalen LG-
Hndler oder einen Unternehmensvertreter von LG. 04 Wir richten unsere Firmenpolitik auf eine sauberere Umwelt hin aus, indem wir umweltspezifische Aspekte als wichtigen Punkt in die Weiterentwicklung unseres Unternehmens einflieen lassen. Zustzliche Informationen ber unsere grne Firmenpolitik erhalten Sie auf unserer Website. http://www.lge.com/about/environment/html/Recycling.jsp Franais Information sur la protection delenvironnement LGE. a publi sa 'Dclaration en faveur dun environnement plus propre' en 1994 et celle-ci est reste, depuis lors, un principe directeur de notre entreprise. Cette dclaration a servi de base notre rflexion et nous a permis de prendre en compte la fois les aspects conomiques et sociaux de nos activits, tout en respectant lenvironnement. Nous encourageons les activits en faveur de la prservation de lenvironnement et cest dans cet esprit que nous dveloppons nos produits : nous rduisons au minimum les matires dangereuses qui entrent dans leur composition et lon ne trouve pas de cadmium, par exemple, dans nos moniteurs. Information sur le recyclage Ce moniteur peut contenir des composants qui prsentent un risque pour lenvironnement. Il est donc important que celui-ci soit recycl aprs usage. LGE. traite les moniteurs en fin de cycle conformment une mthode de recyclage respectueuse de lenvironnement. Nous reprenons nos produits et les recyclons dans plusieurs sites rpartis dans le monde entier. De nombreux composants sont rutiliss et recycls, et les matires dangereuses, ainsi que les mtaux lourds, sont traits selon un procd cologique. Si vous souhaitez plus de renseignements sur notre programme de recyclage, veuillez contacter votre revendeur LG ou un lun de nos reprsentants. Nous voulons agir pour un monde plus propre et croyons au rle de notre entreprise dans lamlioration de lenvironnement. Pour plus de renseignements sur notre politique verte, rendez visite notre site :
http://www.lge.com/about/environment/html/Recycling.jsp Regulatory Information cont. Italiano Informazioni per la tutela dellambiente La LGE. ha annunciato nel 1994 la cosiddetta 'LG Declaration for a Cleaner Environment' (Dichiarazione di LG a favore di un ambiente pi pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale. La dichiarazione rappresenta il fondamento che consente di intraprendere attivit a favore dell'ambiente tenendo conto degli aspetti economici, ambientali e sociali.Noi della LG, promuoviamo attivit a favore della tutela dell'ambiente sviluppando appositamente i nostri prodotti per cogliere il concetto del rispetto dellambiente riducendo i materiali dannosi presenti nei nostri prodotti. Ad esempio nei nostri monitor non presente il cadmio. Informazioni per il riciclaggio Il monitor pu presentare componenti che potrebbero risultare eventualmente dannosi per l'ambiente. importante che il monitor sia riciclato al termine del suo utilizzo. La LGE. gestisce tutti i monitor di rifiuto con un metodo di riciclaggio soddisfacente dal punto di vista ambientale. In tutto il mondo sono attualmente in funzione numerosi sistemi di riciclaggio e recupero. I diversi componenti sono riutilizzati e riciclati, mentre le sostanze dannose e i metalli pesanti vengono trattati con un metodo rispettoso dellambiente. Se si desiderano maggiori informazioni in merito al programma di riciclaggio, consigliabile rivolgersi al proprio rivenditore LG o ad un rappresentante aziendale della LG. Noi della LG impostiamo la nostra visione e le nostre politiche a favore di un mondo pi pulito ponendo la questione dell'ambiente dal punto di vista globale come una mansione rivolta al miglioramento della nostra azienda. Vi invitiamo a visitare il nostro sito internet per ulteriori informazioni sulla nostra politica verde. http://www.lge.com/about/environment/html/Recycling.jsp Espanl Informacin para la conservacin medioambiental LGE. present la 'Declaracin para un entorno ms limpio de LG' en 1994 y este ideal ha servido para guiar nuestros principios empresariales desde entonces. La Declaracin es la base que nos ha permitido llevar a cabo tareas que 05 respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, econmicos y medioambientales. Promocionamos actividades orientadas a la conservacin del medio ambiente y desarrollamos nuestros productos especficamente para que se ajusten a la filosofa que protege el entorno. Reducimos al mximo el uso de materiales de riesgo en nuestros productos. Un ejemplo de ello es la ausencia total de cadmio en nuestros monitores. Informacin para el reciclaje Este monitor puede contener piezas que entraen riesgos medioambientales. Es importante reciclar este monitor despus de su utilizacin. LGE. trata todos los monitores usados siguiendo un mtodo de reciclaje que no daa al entorno. Contamos con diversos sistemas de recuperacin y reciclaje que funcionan a nivel mundial en la actualidad. Es posible reciclar y reutilizar muchas de las piezas, mientras que las sustancias dainas y los metales pesados se tratan siguiendo un mtodo que no perjudique al medio ambiente. Si desea obtener ms informacin acerca del programa de reciclaje, pngase en contacto con su proveedor local de LG o con un representante empresarial de nuestra marca. Basamos nuestra visin y nuestras polticas en un mundo ms limpio y para ellos optamos por un entorno global como tarea principal de nuestra evolucin como empresa. Visite nuestra pgina Web para obtener ms informacin sobre nuestras polticas ecolgicas. http://www.lge.com/about/environment/html/Recycling.jsp Portugus Informaes relacionadas preservao ambiental A LGE. anunciou a 'LG Declaration for a Cleaner Environment' (Declarao da LG para um ambiente mais limpo) em 1994 e esse ideal tem servido desde ento como um princpio administrativo de orientao. A Declarao a base que nos tem permitido realizar atividades favorveis ao ambiente com considerao atenta aos aspectos econmicos, ambientais e sociais. Promovemos atividades de preservao ambiental e desenvolvemos nossos produtos para englobar Regulatory Information cont. especificamente o conceito de favorvel ao ambiente. Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, no h cdmio em nossos monitores. Informaes relacionadas reciclagem Este monitor pode conter peas que podem representar riscos ao ambiente. importante que ele seja reciclado aps o uso. A LGE. cuida de todos os monitores descartados atravs de um mtodo de reciclagem agradvel ao ambiente. H vrios sistemas de devoluo e reciclagem atualmente em operao no mundo. Muitas peas sero reutilizadas e recicladas e as substncias nocivas e os metais pesados passaro por tratamento atravs de um mtodo favorvel ao ambiente. Para obter mais informaes sobre nosso programa de reciclagem, entre em contato com seu fornecedor LG local ou com um representante corporativo da LG. Definimos nossa viso e nossas polticas relacionadas a um mundo mais limpo selecionando a questo do ambiente global como uma tarefa de aprimoramento corporativo. Visite nosso site para obter mais informaes sobre nossas polticas de meio ambiente. http://www.lge.com/about/environment/html/Recycling.jsp Nederlands Informatie met betrekking tot het behoud van het milieu LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner Environment' (de LG-verklaring met betrekking tot een schoner milieu). Deze verklaring en het ideaal van een schoner milieu fungeren sindsdien als een bestuurlijke leidraad voor onze onderneming. Op basis van deze verklaring ontplooien wij milieuvriendelijke activiteiten, waarbij er zowel met sociale en economische aspecten, als met milieuaspecten zorgvuldig rekening wordt gehouden. Wij ondersteunen activiteiten die zijn gericht op het behoud van het milieu en wij houden bij het ontwikkelen onze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen in onze producten. Er wordt bijvoorbeeld geen cadmium verwerkt in onze monitors. Informatie met betrekking tot recycling Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze monitor aan het einde van zijn levensduur wordt gerecycled. LGE. verwerkt alle afvalmonitors via een milieuvriendelijke recyclingmethode. Hiervoor worden er momenteel wereldwijd verscheidene inname- en recyclingsystemen gehanteerd. Een groot aantal onderdelen wordt opnieuw gebruikt en gerecycled, waarbij schadelijke stoffen en zware metalen volgens een milieuvriendelijke methode worden verwerkt. Voor meer informatie over ons recyclingprogramma kunt u contact opnemen met uw plaatselijke LG-
vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonere wereld vloeien voort uit het feit dat wij het milieu hebben aangemerkt als een onderwerp dat speciale aandacht verdient binnen onze onderneming. Bezoek onze website voor meer informatie over ons 'groene' beleid. http://www.lge.com/about/environment/html/Recycling.jsp Russian 1994 LGE
' LG ',
. 06 Regulatory Information cont. K LGE
. LG.
http://www.lge.com/about/environment/html/Recycling.jsp EPA (EPA applied model only) ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. NOM MARK (Mexico only) 07 Regulatory Information cont. WEEE (for Europe ) English Disposal of your old appliance 1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. French limination de votre ancien appareil 1.Ce symbole, reprsentant une poubelle sur roulettes barre d'une croix, signifie que le produit est couvert par la directive europenne 2002/96/EC. 2.Les lments lectriques et lectroniques doivent tre jets sparment, dans les vide-
ordures prvus cet effet par votre municipalit. 3.Une limination conforme aux instructions aidera rduire les consquences ngatives et risques ventuels pour l'environnement et la sant humaine. 4.Pour plus d'information concernant l'limination de votre ancien appareil, veuillez contacter votre mairie, le service des ordures mnagres ou encore la magasin o vous avez achet ce produit. Italian Smaltimento delle apparecchiature obsolete 1.Quando su un prodotto riportato il simbolo di 08 un bidone della spazzatura barrato da una croce significa che il prodotto coperto dalla direttiva europea 2002/96/EC. 2.Tutti i prodotti elettrici ed elettronici dovrebbero essere smaltiti separatamente rispetto alla raccolta differenziata municipale, mediante impianti di raccolta specifici designati dal governo o dalle autorit locali. 3.Il corretto smaltimento delle apparecchiature obsolete contribuisce a prevenire possibili conseguenze negative sulla salute umana e sull'ambiente. 4.Per informazioni pi dettagliate sullo smaltimento delle apparecchiature obsolete, contattare il comune, il servizio di smaltimento rifiuti o il negozio in cui stato acquistato il prodotto. Swedish Kassering av din gamla apparat 1.Nr den hr symbolen med en verkryssad soptunna p hjul sitter p en produkt innebr det att den regleras av European Directive 2002/96/EC. 2.Alla elektriska och elektroniska produkter br kasseras via andra vgar n de som finns fr hushllsavfall, helst via fr ndamlet avsedda uppsamlingsanlggningar som myndigheterna utser. 3.Om du kasserar din gamla apparat p rtt stt s bidrar du till att frhindra negativa konsekvenser fr miljn och mnniskors hlsa. 4.Mer detaljerad information om kassering av din gamla apparat kan fr av kommunen, renhllningsverket eller den butik dr du kpte produkten. Dutch Uw oude toestel wegdoen 1.Als het symbool met de doorgekruiste verrijdbare afvalbak op een product staat, betekent dit dat het product valt onder de Europese Richtlijn 2002/96/EC. 2.Elektrische en elektronische producten mogen niet worden meegegeven met het huishoudelijk afval, maar moeten worden ingeleverd bij speciale inzamelingspunten die door de lokale of landelijke overheid zijn aangewezen. 3.De correcte verwijdering van uw oude toestel helpt negatieve gevolgen voor het milieu en de menselijke gezondheid voorkomen. Regulatory Information cont. 4.Wilt u meer informatie over de verwijdering van uw oude toestel? Neem dan contact op met uw gemeente, de afvalophaaldienst of de winkel waar u het product hebt gekocht. Finnish Vanhojen laitteiden hvittminen 1.Tm merkki tuotteessa tarkoittaa, ett tuote kuuluu shk- ja elektroniikkalaiteromusta annetun EU-direktiivin 2002/96/EY soveltamisalaan. eller de lokale myndigheder. 3.Korrekt bortskaffelse af dit gamle apparat er med til at forhindre mulige skadevirkninger p miljet og menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse af dit gamle apparat kan fs ved at kontakte dit lokale kommunekontor, renovationsselskab eller den butik, hvor du kbte produktet. Greek 2.Kaikki elektroniset laitteet ovat ongelmajtett, 1. joten ne on toimitettava paikalliseen keryspisteeseen. 3.Vanhan laitteen asianmukainen hvittminen ehkisee mahdollisia ympristn ja terveyteen kohdistuvia haittavaikutuksia. 4.Listietoa vanhan laitteen hvittmisest saat ottamalla yhteyden paikallisiin viranomaisiin, kierrtyskeskukseen tai myymln, josta ostit laitteen. German Entsorgung von Altgerten 1.Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europischen Richtlinie 2002/96/EC. 2.Alle Elektro- und Elektronik-Altgerte mssen getrennt vom Hausmll ber dafr staatlich vorgesehenen Stellen entsorgt werden. 3.Mit der ordnungsgemen Entsorgung des alten Gerts vermeiden Sie Umweltschden und eine Gefhrdung der persnlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des alten Gerts erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt oder in dem Geschft, wo Sie das Produkt erworben haben. Danish Sdan smider du dit gamle apparat ud 1.Nr der er et tegn med et kryds over en skraldespand, betyder det, at produktet er omfattet af EU-direktiv 2002/96/EC. 2.Alle elektriske og elektroniske produkter skal smides ud et andet sted end gennem den kommunale affaldsordning ved hjlp af specielle indsamlingsfaciliteter, der er organiseret af staten
, E O 2002/96/EOK. 2.H
. 3.H
. 4.
. Spanish Cmo deshacerse de aparatos elctricos y electrnicos viejos 1.Si en un producto aparece el smbolo de un contenedor de basura tachado, significa que ste se acoge a la Directiva 2002/96/CE. 2.Todos los aparatos elctricos o electrnicos se deben desechar de forma distinta del servicio municipal de recogida de basura, a travs de puntos de recogida designados por el gobierno o las autoridades locales. 3.La correcta recogida y tratamiento de los dispositivos inservibles contribuye a evitar riesgos potenciales para el medio ambiente y la salud pblica. 4.Para obtener ms informacin sobre cmo deshacerse de sus aparatos elctricos y electrnicos viejos, pngase en contacto con su ayuntamiento, el servicio de recogida de basuras o el establecimiento donde adquiri el producto. 09 Regulatory Information cont. Portuguese Hungarian Polish 10 Slovak Czech Croatian Regulatory Information cont. Estonian Latvian Lithuanian 11
This product uses the FCC Data API but is not endorsed or certified by the FCC