52LG50UG LCD TV/MONITOR User manual 1 of 2

 

LCD TV OWNERS MANUAL PLASMA TV PLASMA TV MODELS 42PG25 50PG25 50PG60 60PG60 50PG70 60PG70 LCD TV MODELS 37LG50 32LG30 37LG30 42LG50 47LG50 42LG30 42LGX 52LG50 32LG70 42LG70 47LG70 52LG70 32LG60 37LG60 42LG60 47LG60 52LG60 47LG90 Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. P/NO : SAC30708020 (0804-REV05) www.lgusa.com / www.lg.ca ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner LG Electronics USA, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. FCC NOTICE Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera-

ture accompanying the appliance. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE TO CABLE/TV INSTALLER CAUTION This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the users authority to operate this product 1 SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled Important Safety Instructions. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturers option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction:

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. 1 2 3 Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers)that produce heat. When mounting a TV it on the wall, make sure not to install TV by the hanging power and sig-

nal cables on the back of the TV. 4 5 2 6 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 7 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 8 Only use attachments/accessories specified by the manufacturer. 9 Unplug this apparatus during lighting storms or when unused for long periods of time. 10 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Never touch this apparatus or antenna during a thunder or lighting storm. 15 11 12 13 14 Do not allow a impact shock or any objects to fall into the product, and do not drop onto the screen with something. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates dam-

age or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Outdoor use marking :

WARNING - To reduce the risk of fire or elec-

tric shock, do not expose this appliance to rain or moisture. 16 Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on or over apparatus. 17 GGRROOUUNNDDIINNGG Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker 18 DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS Mains plug is the disconnecting device. The plug must remain readily operable. 3 CONTENTS WARNING / CAUTION . 1 Channel Setup SAFETY INSTRUCTIONS . 2 FEATURE OF THIS TV . 6 PREPARATION Accessories . 7 Front Panel Information . 8 Back Panel Information . 10 Stand Instruction . 13 VESA Wall Mounting . 17 Cable Management . 18 Desktop Pedestal Installation . 20 Swivel Stand . 20 Attaching the TV to a Desk . 20 Securing the TV to the wall to prevent falling . 21 Antenna or Cable Connection . 22 EXTERNAL EQUIPMENT SETUP HD Receiver Setup . 23 DVD Setup . 29 VCR Setup . 33 Other A/V Source Setup . 36 PC Setup . 37 USB Connection . 46 Audio Out Connection . 47 WATCHING TV / CHANNEL CONTROL Remote Control Functions . 48 Turning On the TV . 50 Channel Selection . 50 Volume Adjustment . 50 Quick Menu . 51 Initial Setting . 52 On-Screen Menus Selection . 54

- Auto Scan (Auto Tuning) . 56

- Add / Delete Channel (Manual Tuning) . 57

- Channel Editing . 58 Input List . 59 Input Label . 60 AV Mode . 61 SIMPLINK . 62 USB Entry Modes . 64 Photo List . 65 Music List . 69 PICTURE CONTROL Picture Size (Aspect Ratio) Control . 72 Preset Picture Settings

- Picture Mode - Preset . 74

- Color Tone - Preset . 75 Manual Picture Adjustment

- Picture Mode - User Mode . 76

- Picture Mode - Expert Control . 77 Picture Improvement Technology . 78 Advanced Control - Black (Darkness) Level . 79 Advanced Control - Eye Care . 80 Advanced Control - Real Cinema/Film Mode . 81 Advanced Control - TruMotion . 82 TruMotion Demo . 82 Local Dimming . 83 Local Dimming Demo . 83 Picture Reset . 84 Power Indicator . 85 Image Sticking Minimization (ISM) Method . 86 Power Saving Picture Mode . 87 4 SOUND & LANGUAGE CONTROL APPENDIX Troubleshooting . 118 Maintenance . 120 Product Specifications . 121 Programming the Remote Control . 124 IR Codes . 127 External Control Through RS-232C . 129 Open Source License . 136 Auto Volume Leveler (Auto Volume) . 88 Preset Sound Settings (Sound Mode) . 89 Sound Setting Adjustment - User Mode . 90 Clear Voice . 91 Balance . 92 TV Speakers On/Off Setup . 93 Audio Reset . 94 Stereo/SAP Broadcast Setup . 95 Audio Language . 96 On-Screen Menus Language Selection . 97 Caption Mode

- Analog Broadcasting System Captions . 98

- Digital Broadcasting System Captions . 99

- Caption Option . 100 TIME SETTING Clock Setting

- Auto Clock Setup . 101

- Manual Clock Setup . 102 Auto On/Off Time Setting . 103 Sleep Timer Setting . 104 Auto Shut-off Setting . 105 PARENTAL CONTROL / RATINGS Set Password & Lock System . 106 Channel Blocking . 109 Movie & TV Rating . 110 Downloadable Rating . 115 External Input Blocking . 116 Key lock . 117 5 FEATURE OF THIS TV is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. FOR LCD TV I If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal, there is nothing wrong with TV. I Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. I Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. On Disposal (Only Hg lamp used LCD TV) The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 6 PREPARATION ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. T V S T B Q. M E N U P O W E R D V D V C R IN P U T M E N U E N T E R R E T U R N V O L F A V A V M O D E 1 MUTE 4 2 C H P A G E 7 5 3 8 6 0 9 FLASHBK 1.5V 1.5V Remote Control, Batteries OOppttiioonn EExxttrraass D-sub 15 pin Cable Power Cord When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.

(Only 50PG25, 50/60PG60, 50/60PG70) Copyright 2007 LGE, All Rights Reserved. Owners Manual CD Manual

* Wipe spots on the exterior only with the polishing cloth.

* Do not wipe roughly when removing stain. Excessive pressure may cause scratch or discoloration. Polishing Cloth

(This feature is not available for all models.) FFoorr PPllaassmmaa TTVV mmooddeellss

(Only 42PG25) x 4 Bolts for stand assembly

(Refer to P.13) FFoorr LLCCDD TTVV mmooddeellss Cable Holder Cable Management Clip Protection Cover 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90

(Only 32/37/42LG30, 37/42LG50, 32/42LG70) x 4 x 4

(Only 32LG30/70, 42LG30/50) or Bolts for stand assembly Screw for stand fixing Protection Cover

(Refer to P.16)

(Refer to P.20) 32/37/42/47/52LG60, 42LGX

(Only 32/37LG60)

(Only 42LG60, 42LGX) or 32LG60: 3EA 37LG60: 4EA 4EA 2EA 1EA 4EA Bolts for stand assembly

(Refer to P.14) Protection Cover Cable Management Clip P R E P A R A T O N I 7 PREPARATION FRONT PANEL INFORMATION I Image shown may differ from your TV. I NOTE: If your TV has a protection tape attached, remove the tape. And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it). Plasma TV Models P R E P A R A T O N I Remote Control Sensor POWER Button Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. INPUT MENU ENTER VOL CH INPUT MENU ENTER VOL INPUT MENU INPUT Button ENTER MENU Button VOL ENTER Button CH CH VOLUME

(-, +) Buttons CHANNEL

(EE,DD)Buttons LCD TV Models 32/42/47/52LG70, 47LG90 Intelligent Sensor Adjusts picture according to the surrounding conditions Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on.

(Can be adjusted using PPoowweerr IInnddiiccaattoorr in the OPTION menu. GG pp..8855) Remote Control Sensor POWER Button 8 CH CHANNEL (

Buttons

) VOL ENTER MENU INPUT VOLUME (+, -) Buttons ENTER Button MENU Button INPUT Button LCD TV Models 32/37/42LG30, 37/42/47/52LG50 Intelligent Sensor (Except 32/37/42LG30) Adjusts picture according to the surrounding conditions Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on.

(Can be adjusted using PPoowweerr IInnddiiccaattoorr in the OPTION menu. GG pp..8855) Remote Control Sensor POWER Button 32/37/42/47/52LG60, 42LGX Intelligent Sensor Adjusts picture according to the surrounding conditions. POWER Button Remote Control Sensor Power/Standby Indicator Illuminates red in standby mode. Illuminates white when the set is switched on.

(Can be adjusted using PPoowweerr IInnddiiccaattoorr in the OPTION menu. GG pp..8855) CH VOL ENTER MENU INPUT CH VOL ENTER MENU INPUT CHANNEL (

Buttons

) VOLUME (+, -) Buttons ENTER Button MENU Button INPUT Button CHANNEL (

Buttons

) VOLUME (+, -) Buttons ENTER Button MENU Button INPUT Button P R E P A R A T O N I 9 PREPARATION BACK PANEL INFORMATION I Image shown may differ from your TV. Plasma TV Models 12 3 1 HDMI/DVI IN RGB(PC) RGB IN 5 4 ANTENNA/

CABLE IN AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL 3 2 1 2 1 COMPONENT IN RS-232C IN

(CONTROL & SERVICE) AUDIO OUT O E D V S

I AUDIO VIDEO

( ) MONO VIDEO AUDIO 2 R R 6 7 1 N I V A 8 9

( ) 10 1 9 N I B S U 4 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 1 2 3 4 5 6 HDMI/DVI IN, HDMI IN Digital Connection. Supports HD video and Digital audio. Doesnt support 480i. Accepts DVI video using an adapter or HDMI to DVI cable (not included). COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red and white for audio. RGB (PC) Analog PC Connection. Uses a D-sub 15 pin cable

(VGA cable). AUDIO (RGB/DVI) 1/8 headphone jack for analog PC audio input. REMOTE CONTROL IN PORT For a wired remote control. RS-232C IN (CONTROL & SERVICE) PORT Used by third party devices. ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack. 7 8 9 10 11 12 DIGITAL AUDIO OUT Digital audio output for use with amps and home theater systems. Includes an optical and/or coaxial connection. Note: In standby mode, these ports do not work. AUDIO OUT Analog audio output for use with amps and home theater systems.

( ) AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i). S-VIDEO Better quality than standard composition. Supports standard definition video only (480i). USB INPUT Used for viewing photos and listening to MP3s. USB SERVICE ONLY or RS-232C IN (SERVICE ONLY) Used for software updates. Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. P R E P A R A T O N I 10 LCD TV Models R 12 32/37/42LG30 1 HDMI/DVI IN 2 1 2 1 3 RGB IN RGB(PC) 5 4 ANTENNA/

CABLE IN 6 AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL 7 RS-232C IN

(CONTROL & SERVICE) AUDIO OUT R VIDEO COMPONENT IN AUDIO S-VIDEO VIDEO MONO

( ) AUDIO 1 N I V A 2 8 9

( ) 37/42/47/52LG50, 32LG70 1 HDMI/DVI IN 2 1 2 1 3 RGB IN RGB(PC) 5 4 ANTENNA/

CABLE IN 6 AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL RS-232C IN

(CONTROL & SERVICE) AUDIO OUT 7 1 N I V A 8 9

( ) VIDEO COMPONENT IN AUDIO S-VIDEO VIDEO MONO

( ) AUDIO 2 R P R E P A R A T O N I B S U Y L N O E C U V R E S 3 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 N I B S U 3 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 11 1 9 10 1 9 11 PREPARATION I Image shown may differ from your TV. LCD TV Models P R E P A R A T O N I 12 42/47/52LG70, 47LG90 R R 1 HDMI/DVI IN 3 RGB IN RGB(PC) 5 4 ANTENNA/

CABLE IN 6 AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL 7 3 2 1 RS-232C IN

(CONTROL & SERVICE) AUDIO OUT 8 1 N I V A S-VIDEO VIDEO MONO

( ) AUDIO

( ) 9 R 2 1 VIDEO COMPONENT IN AUDIO 2 10 1 9 N I B S U 4 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 12 32/37/42/47/52LG60, 42LGX 21 N I T N E N O P M O C O E D V I I O D U A 2 11 RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 4 1 2 DIGITAL AUDIO OUT COAXIAL 3 AUDIO

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN 7 6 12 N I I V D

I M D H N I B G R 1 3 R N I B S U 4 N I I M D H R I O D U A O N O M L

O E D V I AV IN 10

( ) 1 9 STAND INSTRUCTION I Image shown may differ from your TV. Plasma TV models INSTALLATION (Only 42PG25) DETACHMENT 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. P R E P A R A T O N I 2 Assemble the TV as shown. 2 Loose the bolts from TV. 42PG25 50PG25/60/70 60PG60/70 3 Fix the 4 bolts securely using the holes in the back of the TV. 3 Detach the stand from TV. PROTECTION COVER After removing the stand, install the included pprrootteeccttiioonn ccoovveerr over the hole for the stand. Press the PPRROOTTEECCTTIIOONN CCOOVVEERR into the TV until you hear it click.

NOTE GG When assembling the desk type stand, check whether the bolt is fully tightened. (If not tight-

ened fully, the product can tilt forward after the product installation). If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. 13 PREPARATION 32/37/42/47/52LG60, 42LGX I Image shown may differ from your TV. INSTALLATION (Only 32/37/42LG60, 42LGX) 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. P R E P A R A T O N I 2 Assemble the parts of the SSTTAANNDD BBOODDYY with CCOOVVEERR BBAASSEE of the TV. 32LG60 37LG60 42LG60, 42LGX SSTTAANNDD BBOODDYY SSTTAANNDD BBOODDYY SSTTAANNDD BBOODDYY CCOOVVEERR BBAASSEE CCOOVVEERR BBAASSEE CCOOVVEERR BBAASSEE 3 Assemble the TV as shown. 4 Fix the 4 bolts securely using the holes in the back of the TV.

NOTE GG When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation). If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. 14 DETACHMENT PROTECTION COVER 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. After removing the stand, install the included pp rr oo--

tteeccttiioonn ccoovveerr over the hole for the stand. 2 Loose the bolts from TV. 3 Detach the stand from TV. After removing the protection paper from the protection cover, adhere it to the TV as shown. P R E P A R A T O N I 15 PREPARATION 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 I Image shown may differ from your TV. INSTALLATION

(Only 32/37/42LG30, 37/42LG50, 32/42LG70) 1 Carefully place the TV screen side down on a cush-

ioned surface to protect the screen from damage. DETACHMENT 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Assemble the parts of the SSTTAANNDD BBOODDYY with CCOOVVEERR BBAASSEE of the TV. 2 Loose the bolts from TV. SSTTAANNDD BBOODDYY CCOOVVEERR BBAASSEE 3 Detach the stand from TV. 3 Assemble the TV as shown. 4 Fix the 4 bolts securely using the holes in the back of the TV. PROTECTION COVER After removing the stand, install the included pprrootteeccttiioonn ccoovveerr over the hole for the stand. Press the PPRROOTTEECCTTIIOONN CCOOVVEERR into the TV until you hear it click. NOTE

GG When assembling the desk type stand, check whether the bolt is fully tightened. (If not tight-

ened fully, the product can tilt forward after the product installation). If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. P R E P A R A T O N I 16 VESA WALL MOUNTING Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. AA BB Product Model 32LG30, 32LG60, 32LG70 37LG30, 37LG60, 37LG50 VESA

(A * B) 200 * 100 LCD TV 42LG30, 42LG50, 42LG60, 42LG70, 42LGX 47LG50, 47LG60, 47LG70, 47LG90 200 * 200 52LG50, 52LG60, 52LG70 42PG25 50PG25, 50PG60, 50PG70 60PG60, 60PG70 800 * 400 400 * 400 600 * 400 PLASMA TV

NOTE Standard Screw Quantity M4 M6 M6 M6 M8 4 4 4 4 4 GG Screw length needed depends on the wall mount used. For further information, refer to the instruc-

tions included with the mount. GG Standard dimensions for wall mount kits are shown in the table. GG When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided. GG Do not use screws longer then the standard dimen-

sion, as they may cause damage to the inside to the TV. GG For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifica-

tions. GG Do not use screws that do not comply with the VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents. GG LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa-

tion instructions. CAUTION GG Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock. P R E P A R A T O N I 17 PREPARATION CABLE MANAGEMENT I Image shown may differ from your TV. Plasma TV Models 1 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. P R E P A R A T O N I 2 Install the CABLE MANAGEMENT CLIP as shown. If your TV has the CABLE HOLDER, install it as shown and bundle the cables. CABLE HOLDER CABLE MANAGEMENT CLIP How to remove the CABLE MANAGEMENT CLIP 42PG25 50PG25, 50/60PG60, 50/60PG70 GG First, press the cable management. Hold the CCAABBLLEE MMAANNAAGGEEMMEENNTT CCLLIIPP with both hands and pull it upward. GG Hold the CABLE MAN-

AGEMENT CLIP with both hands and pull it upward. GG Separate CCAABBLLEE MMAANN--

AAGGEEMMEENNTT CCLLIIPP from TV by pressing two latches. NOTE

GG Do not hold the CABLE MANAGEMENT CLIP when moving the TV.

- If the TV is dropped, you may be injured or the product may be broken. 18 LCD TV Models 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 1 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. 32/37/42/47/52LG60, 42LGX 1 Align the hole with the tab on the CCAABBLLEE MMAANNAAGGEEMMEENNTT CCLLIIPP. Turn the CCAABBLLEE MMAANNAAGGEEMMEENNTT CCLLIIPP as shown. Note: This cable management clip can be bro-

ken by excessive pressure. P R E P A R A T O N I 2 Install the CABLE MANAGEMENT CLIP as shown. CABLE MANAGEMENT CLIP 3 Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed. 2 Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. 19 PREPARATION DESKTOP PEDESTAL INSTALLATION I Image shown may differ from your TV. For proper ventilation, allow a clearance of 4 inches on all four sides from the wall. 4 inches 4 inches 4 inches 4 inches CAUTION GG Ensure adequate ventilation by following the clearance recommendations. GG Do not mount near or above any type of heat source. SWIVEL STAND After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position. ATTACHING THE TV TO A DESK (Only 32LG30/70, 42LG30/50) The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Stand Desk 1-Screw

(provided as parts of the product) WARNING GG To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury. P R E P A R A T O N I 20 SECURING THE TV TO THE WALL TO PREVENT FALLING I You should purchase necessary components to prevent TV from falling off of the stand. I Image shown may differ from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children dont climb on or hang from the TV. P R E P A R A T O N I I Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. I Use a sturdy rope (not provided as parts of the product, must pur-

chase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. NOTE

GG Use a platform or cabinet strong enough and large enough to support the size and weight of the TV. GG To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same. 21 PREPARATION I To prevent damage do not connect to the power outlet until all connections are made between the devices. ANTENNA OR CABLE CONNECTION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection. For optimum picture quality, adjust the antenna direction if needed. P R E P A R A T O N I R R ANTENNA/

CABLE IN Wall Antenna Socket Outdoor Antenna

(VHF, UHF) 2. Cable Cable TV Wall Jack Multi-family Dwellings/Apartments

(Connect to wall antenna socket) RF Coaxial Wire (75 ohm) Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the copper wire when connecting the antenna.

( ) ANTENNA/

CABLE IN RF Coaxial Wire (75 ohm) I To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. I If the antenna needs to be split for two TVs, install a 2-Way Signal Splitter. I If the antenna is not installed properly, contact your dealer for assistance.

( ) 22 EXTERNAL EQUIPMENT SETUP I To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. I Image shown may differ from your TV. HD RECEIVER SETUP This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device. Component Connection 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the digital set-

top box to the CCOOMMPPOONNEENNTT IINN VVIIDDEEOO 11 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 Connect the audio output of the digital set-top box to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO 11 jacks on the TV. 2. How to use I Turn on the digital set-top box.

(Refer to the owners manual for the digital set-top box. operation) I Select the CCoommppoonneenntt 11 input source on the TV using the IINNPPUUTT button on the remote control. I If connected to CCOOMMPPOONNEENNTT IINN22 input, select the CCoommppoonneenntt 22 input source on the TV. Supported Resolutions Signal 480i 480p 720p 1080i 1080p Component HDMI Yes Yes Yes Yes Yes No Yes Yes Yes Yes Y, CB/PB, CR/PR Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480i 720x480p 1280x720p 1920x1080i 1920x1080p 15.73 15.73 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 59.94 60.00 59.94 60.00 59.94 60.00 59.94 60.00 23.976 24.00 29.97 30.00 59.94 60.00 E X T E R N A L E Q U I P M E N T S E T U P 23 EXTERNAL EQUIPMENT SETUP Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 Y PB PR L R E X T E R N A L E Q U I P M E N T S E T U P 24 1 2 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGI OPT RS-232

(CONTROL &

2 1 Y PB PR L R VIDEO COMPONENT IN AUDIO S-VIDEO 32/37/42/47/52LG60, 42LGX 21 O E D V I I O D U A 1 2 DIGITAL AUDIO OUT COAXIAL N I T N E N O P M O C N I I V D

I I B G R M D 3 H AUDIO N

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 1 2 L R Y PB PR HDMI Connection 1. How to connect 1 2 Connect the digital set-top box to HHDDMMII//DDVVII IINN11, 22, 33, or 44 jack on the TV. No separate audio connection is necessary. HDMI supports both audio and video. 2. How to use I Turn on the digital set-top box.

(Refer to the owners manual for the digital set-top box.) I Select the HHDDMMII11, HHDDMMII22, HHDDMMII33, or HHDDMMII44 input source on the TV using the IINNPPUUTT button on the remote control. HDMI-DTV Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480p 1280x720p 1920x1080i 1920x1080p 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 59.94 60.00 59.94 60.00 59.94 60.00 23.976 24.00 29.97 30.00 59.939 60.00 E X T E R N A L E Q U I P M E N T S E T U P 25 EXTERNAL EQUIPMENT SETUP 32/37/42LG30, 37/42/47/52LG50, 32LG70 Plasma TV, 42/47/52LG70, 47LG90 RGB IN RGB(PC) A

(RG 2 1 Y PB PR VIDEO COMPONENT HDMI/DVI IN 2 1 HDMI/DVI IN RGB IN RGB(PC) 3 2 1 Y PB PR VIDEO COMPON 1 1 HDMI-DTV OUTPUT HDMI-DTV OUTPUT 32/37/42/47/52LG60, 42LGX N I T N E N O P M O C 21 O E D V I I O D U A 1 2 DIGITAL AUDIO OUT COAXIAL 3 AUDIO

(RGB/DVI) OPTICAL RGB(PC) N I I V D

I M D H N I B G R ANTENNA/

CABLE IN RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 1 HDMI-DTV OUTPUT E X T E R N A L E Q U I P M E N T S E T U P 26 DVI to HDMI Connection 1. How to connect 1 2 32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV

- Connect the DVI output of the digital set-top box to the HHDDMMII//DDVVII IINN 11, 22, or 33 jack on the TV. 32/37/42/47/52LG60, 42/47/52LG70, 42LGX, 47LG90

- Connect the DVI output of the digital set-top box to the HHDDMMII//DDVVII IINN 11, 22, 33, or 44 jack on the TV. Connect the PC audio output to the AAUUDDIIOO ((RRGGBB//DDVVII)) jack on the TV. 2. How to use I Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) I 32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV

- Select the HHDDMMII11, HHDDMMII22, or HHDDMMII33 input source on the TV using the IINNPPUUTT button on the remote control. I 32/37/42/47/52LG60, 42/47/52LG70, 42LGX, 47LG90

- Select the HHDDMMII11, HHDDMMII22, HHDDMMII33, or HHDDMMII44 input source on the TV using the IINNPPUUTT button on the remote control.

NOTE GG A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary. E X T E R N A L E Q U I P M E N T S E T U P 27 EXTERNAL EQUIPMENT SETUP 32/37/42LG30, 37/42/47/52LG50, 32LG70 Plasma TV, 42/47/52LG70, 47LG90 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN HDMI/DVI IN R

(CONT Y PB PR L R VIDEO COMPONENT IN AUDIO S 3 2 1 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOT CONTROL Y PB PR 2 1 L R VIDEO COMPONENT IN AUDIO

1 N I V A

( ) 2 1 2 HDMI/DVI IN 2 1 2 1 1 E X T E R N A L E Q U I P M E N T S E T U P DVI-DTV OUTPUT L R DVI-DTV OUTPUT L R 32/37/42/47/52LG60, 42LGX 1 N I T N E N O P M O C 21 O E D V I 2 I O D U A 1 2 3 DIGITAL AUDIO OUT COAXIAL AUDIO

(RGB/DVI) OPTICAL RGB(PC) N I I V D

I M D H N I B G R ANTENNA/

CABLE IN RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN DVI-DTV OUTPUT L R 28 DVD SETUP Component Connection 1. How to connect 1 Connect the video outputs (Y, PB, PR) of the DVD to the CCOOMMPPOONNEENNTT IINN VVIIDDEEOO11 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). 2 Connect the audio outputs of the DVD to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO11 jacks on the TV. 2. How to use I Turn on the DVD player, insert a DVD. I Select the CCoommppoonneenntt 11 input source on the TV using the IINNPPUUTT button on the remote control. I If connected to CCOOMMPPOONNEENNTT IINN 22 input, select the CCoommppoonneenntt 22 input source on the TV. I Refer to the DVD player's manual for operating instructions. Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Video output ports on DVD player Y Y Y Y Y PB PB B-Y Cb Pb PR PR R-Y Cr Pr E X T E R N A L E Q U I P M E N T S E T U P 29 EXTERNAL EQUIPMENT SETUP Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 Y PB PR L R E X T E R N A L E Q U I P M E N T S E T U P 30 1 2 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITA OPTICA RS-232C I

(CONTROL & SER 2 1 Y PB PR L R VIDEO COMPONENT IN AUDIO S-VIDEO V 32/37/42/47/52LG60, 42LGX 21 O E D V I I O D U A 1 2 DIGITAL AUDIO OUT COAXIAL N I T N E N O P M O C N I I V D

I I B G R M D 3 H AUDIO N

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN 1 2 L R Y PB PR S-Video Connection (Except 32/37/42/47/52LG60, 42LGX) 1. How to connect 1 2 Connect the S-VIDEO output of the DVD to the SS --VVIIDDEEOO input on the TV. Connect the audio outputs of the DVD to the AAUUDDIIOO input jacks on the TV. 2. How to use I Turn on the DVD player, insert a DVD. I Select the AA VV 11 input source on the TV using the IINNPPUUTT button on the remote control. I Refer to the DVD player's manual for operating instructions. S-VIDEO AUDIO L R ANTENNA/

CABLE IN UDIO B/DVI) REMOTE CONTROL IN 2 1 DIGITAL AUDIO OUT OPTICAL COAXIAL RS-232C IN

(CONTROL & SERVICE) AUDIO OUT L R AUDIO N S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A E X T E R N A L E Q U I P M E N T S E T U P 31 EXTERNAL EQUIPMENT SETUP HDMI Connection 1. How to connect 1 2 Connect the HDMI output of the DVD to the HHDDMMII//DDVVII IINN11, 22, 33 or 44 jack on the TV. No separate audio connection is necessary. HDMI supports both audio and video. 2. How to use I Select the HHDDMMII11, HHDDMMII22, HHDDMMII33, or HHDDMMII44 input source on the TV using the IINNPPUUTT button on the remote control. I Refer to the DVD player's manual for operating instructions. 32/37/42LG30, 37/42/47/52LG50, 32LG70 RGB(PC) AUDIO

(RGB/D 2 1 Y PB PR L VIDEO COMPONENT IN A HDMI/DVI IN 2 1 1 HDMI-DVD OUTPUT Plasma TV, 42/47/52LG70, 47LG90 32/37/42/47/52LG60, 42LGX HDMI/DVI IN RGB IN RGB(PC) 3 2 1 Y PB PR

(R 2 1 VIDEO COMPONENT 1 HDMI-DVD OUTPUT 21 O E D V I I O D U A 1 2 DIGITAL AUDIO OUT COAXIAL 3 AUDIO

(RGB/DVI) N I I V D

I M D H N I B G R N I T N E N O P M O C

( ) OPTICAL RGB(PC) ANTENNA/

CABLE IN RS-232C IN

(SERVICE ONLY) 1 REMOTE CONTROL IN HDMI-DVD OUTPUT E X T E R N A L E Q U I P M E N T S E T U P 32 VCR SETUP I To avoid picture noise (interference), leave an adequate distance between the VCR and TV. I Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period of time (Plasma TV models only). If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty. Antenna Connection 1. How to connect Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 1 2 Connect the RF antenna out socket of the VCR to the AANNTTEENNNNAA//CCAABBLLEE IINN sock-

et on the TV. ANTENNA/

CABLE IN UDIO OUT COAXIAL 1 Connect the antenna cable to the RF antenna in socket of the VCR. AUDIO OUT E) 2. How to use I Set VCR output switch to 3 or 4 and then EO L

(MONO) AUDIO R tune TV to the same channel number. I Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) 1 N I V A ANT OUT S-VIDEO VIDEO L R ANT IN OUTPUT SWITCH Wall Jack 2 Antenna 32/37/42/47/52LG60, 42LGX P M O C I O D U A COAX OPTIC 1 ANTENNA/

CABLE IN RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN S-VIDEO VIDEO L R ANT OUT OUTPUT SWITCH ANT IN 2 Wall Jack Antenna E X T E R N A L E Q U I P M E N T S E T U P 33 EXTERNAL EQUIPMENT SETUP Composite (RCA) Connection 1. How to connect 1 Connect the AAUUDDIIOO/VVIIDDEEOO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left

= white, and Audio Right = red) Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 ANT IN S-VIDEO VIDEO L R 2. How to use I Insert a video tape into the VCR and press PLAY on the VCR.

(Refer to the VCR owners manual.) I Select the AA VV 11 input source on the TV using the IINNPPUUTT button on the remote control. I If connected to AAVV IINN22, select AAVV22 input source on the TV. NOTE

GG If you have a mono VCR, connect the audio cable from the VCR to the AAUUDDIIOO LL//MMOONNOO jack of the TV. ANT OUT OUTPUT SWITCH 1 ANTENNA/

CABLE IN AUDIO

(RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL RS-232C IN

(CONTROL & SERVICE) AUDIO OUT L R AUDIO NT IN S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A N I B S U 4 N I I M D H R I O D U A O N O M L

O E D V I AV IN 32/37/42/47/52LG60, 42LGX 1 ANT IN S-VIDEO VIDEO L R ANT OUT OUTPUT SWITCH E X T E R N A L E Q U I P M E N T S E T U P 34 S-Video Connection (Except 32/37/42/47/52LG60, 42LGX) 1. How to connect 1 2 Connect the S-VIDEO output of the VCR to the SS --VVIIDDEEOO input on the TV. ANT IN S-VIDEO VIDEO L R Connect the audio outputs of the VCR to the AAUUDDIIOO input jacks on the TV. ANT OUT OUTPUT SWITCH ANTENNA/

CABLE IN AUDIO

(RGB/DVI) REMOTE CONTROL IN 2 1 DIGITAL AUDIO OUT OPTICAL COAXIAL RS-232C IN

(CONTROL & SERVICE) AUDIO OUT L R AUDIO NT IN S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A 2. How to use I Insert a video tape into the VCR and press PLAY on the VCR.

(Refer to the VCR owners manual.) I Select the AA VV 11 input source on the TV using the IINNPPUUTT button on the remote control.

NOTE GG S-Video provides better quality than composite. Use it when available. CAUTION GG Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. E X T E R N A L E Q U I P M E N T S E T U P 35 Camcorder Video Game Set VIDEO L R 1 N I B S U 3 N I I M D H R I O D U A O N O M L

O E D V I EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP 1. How to connect 1 Connect the AAUUDDIIOO/VVIIDDEEOO jacks between TV and external equipment. Match the jack colors.

(Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use I Select the AA VV 22 input source on the TV using the IINNPPUUTT button on the remote control. I If connected to AAVV IINN11 input, select the AA VV 11 input source on the TV. I Operate the corresponding external equipment. E X T E R N A L E Q U I P M E N T S E T U P 36 PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) Connection Plasma TV, 32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90 32/37/42/47/52LG60, 42LGX N 2 1 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN

(CO Y PB PR L R VIDEO COMPONENT IN AUDIO 1 2 N I T N E N O P M O C O E D V I I O D U A 1 2 DIGITAL AUDIO OUT COAXIAL D

I M D 3 H AUDIO N I B G R

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN 2 1 RS-232C IN

(SERVICE ONLY) REMOTE CONTROL IN RGB OUTPUT AUDIO RGB OUTPUT AUDIO 1. How to connect 1 2 Connect the VGA output of the PC to the RR GG BB ((PP CC)) jack on the TV. Connect the PC audio output to the AAUUDDIIOO ((RRGGBB//DDVVII)) jack on the TV. 2. How to use I Turn on the PC and the TV. I Select the RRGGBB--PPCC input source on the TV using the IINNPPUUTT button on the remote control. E X T E R N A L E Q U I P M E N T S E T U P 37 EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection 1. How to connect 1 2 32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV

- Connect the DVI output of the PC to the HHDDMMII//DDVVII IINN 11, 22, or 33 jack on the TV. 32/37/42/47/52LG60, 42/47/52LG70, 42LGX, 47LG90

- Connect the DVI output of the PC to the HHDDMMII//DDVVII IINN 11, 22, 33, or 44 jack on the TV. Connect the PC audio output to the AAUUDDIIOO ((RRGGBB//DDVVII)) jack on the TV. 2. How to use I Turn on the PC and the TV. I 32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV

- Select the HHDDMMII11, HHDDMMII22, or HHDDMMII33 input source on the TV using the IINNPPUUTT button on the remote control. I 32/37/42/47/52LG60, 42/47/52LG70, 42LGX, 47LG90

- Select the HHDDMMII11, HHDDMMII22, HHDDMMII33, or HHDDMMII44 input source on the TV using the IINNPPUUTT button on the remote control.

NOTES GG 32/37/42LG30, 42/50PG25: To get the the best picture quality, adjust the PC graphics card to 1360x768. GG 37/42/47/52LG50, 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90, 50/60PG60, 50/60PG70: To get the the best picture quality, adjust the PC graphics card to 1920x1080. the resolution, vertical pattern, contrast or bright-

ness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. GG Avoid keeping a fixed image on the screen for a long period of time. The fixed image could become permanently imprinted on the screen. GG Depending on the graphics card, DOS mode may GG The synchronization input form for Horizontal and not work if a HDMI to DVI Cable is in use. Vertical frequencies is separate. GG In PC mode, there may be noise associated with E X T E R N A L E Q U I P M E N T S E T U P 38 32/37/42LG30, 37/42/47/52LG50, 32LG70 Plasma TV, 42/47/52LG70, 47LG90 HDMI/DVI IN 2 1 2 1 1 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN HDMI/DVI IN R

(CONT Y PB PR L R VIDEO COMPONENT IN AUDIO S 3 2 1 RGB IN RGB(PC) AUDIO

(RGB/DVI) REMOTE CONTROL IN

(CO Y PB PR 2 1 L R VIDEO COMPONENT IN AUDIO 1 N I V A 2 1 2 DVI-PC OUTPUT AUDIO DVI-PC OUTPUT AUDIO N I I V D

I M D H N I B G R 32/37/42/47/52LG60, 42LGX 21 1 2 DIGITAL AUDIO OUT COAXIAL 3 AUDIO

(RGB/DVI) OPTICAL RGB(PC) ANTENNA/

CABLE IN N I T N E N O P M O C O E D V I I O D U A 1 RS-232C IN 2

(SERVICE ONLY) REMOTE CONTROL IN DVI-PC OUTPUT AUDIO

( ) E X T E R N A L E Q U I P M E N T S E T U P 39 EXTERNAL EQUIPMENT SETUP Supported Display Specifications (RGB-PC, HDMI-PC)

NOTE GG Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly. GG If there are overscan in HDMI-PC 1920x1080, change aspect ratio to JJuusstt ssccaann. For 32/37/42LG30 For 37/42/47/52LG50, 32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90 Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 31.468 640x350 31.469 720x400 640x480 800x600 1024x768 1280x768 1360x768 1366x768 31.469 31.469 37.879 48.363 47.776 47.720 47.130 70.08 70.08 59.94 60.31 60.00 59.87 59.799 59.65

* Only RGB-PC mode 70.09 70.08 59.94 75.00 72.80 56.25 60.31 75.00 72.18 60.00 70.06 75.02 59.87 74.893 60.02 75.025 60.015 60.00 31.469 31.469 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 47.776 60.289 63.981 79.976 47.712 75.00 720x400 640x480 800x600 1024x768 1280x768 1280x1024 1360x768 1600x1200 1920x1080 RGB-PC 1920x1080 HDMI-PC 66.587 59.934 67.5 60.00

* Only RGB-PC mode E X T E R N A L E Q U I P M E N T S E T U P 40 For 42/50PG25, 50/60PG60, 50/60PG70 Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 31.468 720x400 640x480 800x600 1024x768 1280x768 1280x1024 1360x768 1600x1200 31.469 31.469 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 47.776 60.289 63.981 79.976 47.712 75.00 70.09 70.08 59.94 75.00 72.80 56.25 60.31 75.00 72.18 60.00 70.06 75.02 59.87 74.893 60.02 75.025 60.015 60.00 1920x1080 66.587 59.934

* Only RGB-PC mode E X T E R N A L E Q U I P M E N T S E T U P 41 EXTERNAL EQUIPMENT SETUP Screen Setup for PC mode Selecting Resolution You can choose the resolution in RGB-PC mode. The PPoossiittiioonn, PPhhaassee, and SSiizzee can also be adjusted. PICTURE Move Enter SCREEN Move MENU Prev. E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo 1024 x 768 1280 x 768 1360 x 768 1366 x 768 Resolution G Auto config. Position Size Phase Reset Only for 32/37/42LG30 Select PPIICCTTUURREE. Select SSccrreeeenn ((RRGGBB--PPCC)). Select RReessoolluuttiioonn. Select the desired resolution. 1 MENU 2 3 4 5 ENTER ENTER ENTER ENTER E X T E R N A L E Q U I P M E N T S E T U P 42 Auto Configure Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC. PICTURE Move Enter SCREEN Move MENU Prev. E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo Resolution Auto config. G Position Size Phase Reset To Set Yes No 1 MENU Select PPIICCTTUURREE. 2 3 4 5 ENTER ENTER Select SSccrreeeenn ((RRGGBB--PPCC)). Select AAuuttoo ccoonnffiigg... ENTER Select YY ee ss. ENTER Start Auto Configuration. If the position of the image is still not correct, try Auto adjustment again. If picture needs to be adjusted again after Auto adjustment in RGB-PC, you can adjust the PP oo ss ii tt ii oo nn, SS ii zz ee or PPhhaassee. E X T E R N A L E Q U I P M E N T S E T U P 43 EXTERNAL EQUIPMENT SETUP Adjustment for screen Position, Size, and Phase If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This feature operates only in RGB-PC mode. PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo SCREEN Move MENU Prev. Resolution Auto config. Position G Size Phase Reset F D E G 1 MENU 2 3 4 5 ENTER ENTER ENTER ENTER Select PPIICCTTUURREE. Select SSccrreeeenn ((RRGGBB--PPCC)). Select PPoossiittiioonn, SS ii zz ee, or PPhhaassee. Make appropriate adjustments. I PPoossiittiioonn: This function is to adjust pic-

ture to left/right and up/down as you prefer. I SS ii zz ee: This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. I PP hh aa ss ee: This function allows you to remove any horizontal noise and clear or sharpen the image of characters. E X T E R N A L E Q U I P M E N T S E T U P 44 Screen Reset (Reset to original factory values) Returns PPoossiittiioonn, SS ii zz ee, and PPhhaassee to the default factory settings. This feature operates only in RGB-PC mode. PICTURE Move Enter E 50 60 60 0 Brightness Sharpness Color Tint Advanced Control Reset R G Screen (RGB-PC) TruMotion Demo SCREEN Move MENU Prev. Resolution Auto config. Position Size Phase Reset G To Set Yes No Select PPIICCTTUURREE. Select SSccrreeeenn ((RRGGBB--PPCC)). Select RReesseett. Select YY ee ss. 1 MENU 2 3 4 5 ENTER ENTER ENTER ENTER E X T E R N A L E Q U I P M E N T S E T U P 45 EXTERNAL EQUIPMENT SETUP USB CONNECTION (Except 32/37/42LG30) i.e) or 1 N I B S U 3 N I I M D H R I O D U A O N O M L

O E D V I AV IN 2 1. How to connect 1 Connect the USB device to the UUSSBB II NN jack on the side of TV. 2. How to use I After connecting the UUSSBB II NN jack, you use the USB func-

tion. (GG pp..6644) E X T E R N A L E Q U I P M E N T S E T U P 46 AUDIO OUT CONNECTION Send the TVs audio to external audio equipment via the Audio Output port. Analog (Except 32/37/42/47/52LG60, 42LGX) 1. How to connect 1 2 Connect audio outputs to the TVs AAUUDDIIOO OOUUTT jacks. Set the TV Speaker option - Off in the AUDIO menu.

(GG pp..9933). See the external audio equipment instruction manual for operation. Digital 1. How to connect RS-232C IN

(CONTROL & SERVICE) AUDIO OUT R AUDIO S-VIDEO VIDEO L

(MONO) AUDIO R 1 L R AUDIO 1 N I V A 1 2 3 Connect one end of the optical or coaxial cable to the TVs OOPPTTIICCAALL or CCOOAAXXIIAALL (Except 32/37/42LG30) port of DDIIGGIITTAALL AAUUDDIIOO OOUUTT. Connect the other end of the optical or coaxial cable to the digital audio input on the audio equipment. ANTENNA/

CABLE IN UDIO B/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL COAXIAL Set the TV Speaker option - Off in the AUDIO menu. (GG pp..9933). See the external audio equipment instruction manu-

al for operation. RS-232C IN 1

(CONTROL & SERVICE) AUDIO OUT L R AUDIO N S-VIDEO VIDEO L

(MONO) AUDIO R 1 N I V A 2

NOTE GG When connecting with external audio equipments, such as amplifiers or speakers, you can turn the TV speakers off in the menu. (GG pp .. 99 33) CAUTION G Do not look into the optical output port. Looking at the laser beam may damage your vision. GG Block the SPDIF out (optical/coaxial) about the contents with ACP(Audio Copy Protection) function. E X T E R N A L E Q U I P M E N T S E T U P 47 WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS When using the remote control, aim it at the remote control sensor on the TV. TV/STB/DVD/VCR Select the remote operating mode: TV, STB, DVD, or VCR. POWER Turns your TV or any other programmed equipment on or off, depending on the mode. Q.MENU Select the desired quick menu source. GG pp..5511 TV POWER DVD STB Q. MENU MENU VCR INPUT MENU Displays the main menu. Clear all on-screen displays and return to TV viewing from any menu. ENTER INPUT External input modes rotate in regular sequence. VOLUME UP

/DOWN Increase/decrease the sound level. FAV Scroll through the programmed Favorite channels. GG pp..5511 MUTE Switch the sound on or off. GG pp..5500 CHANNEL UP/DOWN PAGE UP/DOWN NUMBER button

(DASH) Select available channels. Move from one full set of screen information to the next one. Used to enter a program number for multiple program channels such as 2-1, 2-2, etc. FLASHBK Tune to the last channel viewed. RETURN AV MODE VOL 1 4 7 FAV MUTE 2 5 8 0 CH P A G E 3 6 9 FLASHBK VCR/DVD, USB, SIMPLINK Control buttons Control video cassette recorders or DVD players. Control USB menu (PHOTO LIST and MUSIC LIST.) Control the SIMPLINK compatible devices. W A T C H I N G T V

C H A N N E L C O N T R O L 48 THUMBSTICK

(Up/Down/Left Right/ENTER) Navigate the on-screen menus and adjust the system settings to your preference. RETURN Allows the user to move return one step in an interactive application or other user interaction function. SIMPLINK See a list of AV devices connected to TV. When you toggle this button, the SIMPLINK menu appears at the screen. GG pp..6622--6633 AV MODE It helps you select and set images and sounds. GG pp..6611 Installing Batteries I Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +,-with -). I Install two 1.5V AAA batteries. Dont mix old or used batteries with new ones. I Close cover. W A T C H I N G T V

C H A N N E L C O N T R O L 49 WATCHING TV / CHANNEL CONTROL TURNING ON THE TV 1 2 3 First, connect power cord correctly. At this moment, the TV switches to standby mode. I In standby mode to turn TV on, press the button on the TV or press the PPOOWWEERR, IINNPPUUTT, CCHH((

((00~99)) button on the remote control. or

, IINNPPUUTT, CCHH ((DDEE or

)), NNuummbbeerr Select the viewing source by using the IINNPPUUTT button on the remote control. I This TV is programmed to remember which power state it was last set to, even if the power cord is out. When finished using the TV, press the PPOOWWEERR button on the remote control. The TV reverts to standby mode.

NOTE GG If you intend to be away on vacation, disconnect the power plug from the wall power outlet. CHANNEL SELECTION 1 Press the CCHH ((

or

)) or NNUUMMBBEERR buttons to select a channel number. VOLUME ADJUSTMENT Adjust the volume to suit your personal preference. 1 2 3 Press the VVOOLL ((++ or --)) button to adjust the volume. If you want to switch the sound off, press the MMUUTTEE button. You can cancel the Mute function by pressing the MMUUTTEE or VVOOLL ((++ or --)) button. W A T C H I N G T V

C H A N N E L C O N T R O L 50