| submitted | available | document details (if available) | source link |
|---|---|---|---|
| September 01 2007 | October 01 2007 |
| various | user manual | Users Manual | 228.26 KiB | September 01 2007 / October 01 2007 |
Wireless Kit OWNERS MANUAL MODEL: ACC97WK
(ACC97WK-T, ACC97WK-R) Before connecting, operating or adjusting this product, please read this owners manual carefully and completely. Call us and we will guide you through your first recording, for free. 1-800-243-0000 Specifications Wireless TX Dimensions (approx.)(w x h x d) . 149 X 79 X 151 mm (5.8 x 3.1 x 5.9 inches) Mass (approx.) . 0.15 kg (0.33 lbs) Transmission Output . 2.4GHz Power Supply . DC 7V Wireless RX Power requirements . AC 120 V, 60 Hz Power consumption . 50 W Dimensions (approx.)(w x h x d) . 111 X 266 X 180 mm (4.3 x 10.4 x 7.0 inches) Mass (approx.) . 1.3 kg (2.86 lbs) Reception Output . 2.4GHz Amplifier . 155W + 155W (Reated Output Power: 130W, 4, THD 10 %) IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNERS MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing. This product does not contain any parts that can be repaired by the user. DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL ONLY. 1. Read these instructions. - All these safety and operating instructions should be read before the product is operated. 2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the 3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to. 4. Follow all instructions. - All operating and use instructions should be followed. 5. Do not use this apparatus near water. For example:
near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water. 6. Clean only with dry cloth. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners. 7. Do not block any ventilation openings. Install in accor-
dance with the manufacturers instructions. - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over- heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ven-
tilation is provided or the manufacturers instructions have been adhered to. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-
over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate nor-
mally, or has been dropped. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION:
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface.This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedi-
cated circuit;
That is, a single outlet circuit which powers only that appli-
ance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, dis-
continue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is eas-
ily accessible. FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equip-
ment may cause harmful interference unless the modifica-
tions are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. REGULATORY INFORMATION: FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio com-
munications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this product does cause harmful interference to radio or television recep-
tion, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the product and receiver. Connect the product into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV techni-
cian for help.
- Labelling information: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- RF Exposure Statement: The antenna(s) used for this trans-
mitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be colocated or operating in conjunction with any antenna or transmitter other than those contained in this device. FCC COMPLIANCE: The responsible party for this products compliance is:
LG Electronics U.S.A., Inc.,1000 Sylvan Avenue, Englewood Cliffs, NJ. Phone: 1-201-816-2000. FCC Regulations Part 15 Declaration of Conformity
(DoC) LG Corporation declares that the equipment described in this document is within the requirements of the Code of Federal Regulations listed below:
Title 47 Part 15, Subpart B, Class B for a digital device. This declaration is based upon the compliance of the Audio data transceiver to the above standards. LG has determined that the models listed have been shown to comply with the applicable technical standards if no unauthorized change is made in the equipment and if the equipment is properly maintained and operated. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. LG Electronics, Inc. Limited Warranty - USA This LG Electronics product, will be repaired or replaced, at LGs option, if it proves to be defective in material or work-
manship, under normal use, during the warranty period (Warranty Period) listed below, effective from the date (Date of Purchase) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the United States, excluding U.S. Territories. WARRANTY PERIOD:
HOW SERVICE IS HANDLED:
LABOR: 90 days from the Date of Purchase. PARTS: One Year from the Date of Purchase.
* Parts replaced are warranted for the remaining portion of the original warranty period. Call 1-800-243-0000 for instructions on getting the defective unit repaired or replaced. Please retain dated sales receipt and your box to return the unit to LG for repair or replacement. Shipping both ways will be paid by LG during the Warranty Period. After the Warranty Period, you pay inbound ship-
ping charges and LG pays return shipping charges. Visit our website at: http://www.lgservice.com THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. LG ELECTRONICS WILL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES OF ANY NATURE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROF-
ITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that may vary from state to state. THIS LIMITED WARRANTY DOES NOT APPLY TO:
Damages or operating problems that result from shipping, installation, adjustment of user controls, calibration, maintenance or failure to maintain, or separate system components; and Damages or operating problems that result from normal wear and tear, misuse, abuse, operation outside environ-
mental specifications or contrary to the requirements or precautions in the Operating Guide, accident, lightning strikes or other natural causes, unauthorized modification or alteration, incorrect electrical current or voltage, reception problem caused by inadequate home antenna or faulty antenna connections, computer software, insti-
tutional or commercial use, or other causes not arising out of defect in material or workmanship. Therefore, the cost of repair or replacement of such defective product shall be borne by the consumer. CUSTOMER INTER-ACTIVE CENTER NUMBERS:
Setup Note:
If there is a product with a strong electromagnetic field near-
by, interference may occur.
(Ex : Micro wave oven) Wireless TX LED indicator Displays the operating status. LED indicator of Wireless TX
* LED indicator - BLUE The main set is turned on, everthing is connected and transmitting.
* LED indicator - OFF (No display) The main set is turned off. Wireless RX DC IN connector ID/CHANNEL (ID./CH.) button SOUND SIGNAL connector LED indicator Displays the operated status. LED indicator of Wireless RX
* LED indicator - BLUE The Wireless TX is receiving a signal of Wireless TX.
* LED indicator - RED The Wireless RX is in standby mode. ID. button (or ID button) Changing a channel of Wireless TX and Wireless RX If there is a similar wireless product nearby, interference may occur. In this case, change to another channel using ID/CHANNEL (ID./CH.) button of Wireless TX. Manual setting
Press ID/CHANNEL (ID./CH.) button for about 3 seconds. If the wireless TX and wireless RX signals do not match after operating as above, operate it again about three times. Auto setting 1 Disconnect the DC power cable from the Wireless TX. 2 Connect the DC power cable Wireless TX while you pressing the ID/CHANNEL (ID.CH.) button of Wiress TX.
- The blue LED indicator will flicker. 3 Disconnect the DC power cable from the Wireless TX and release the ID/CHANNEL (ID.CH.) button of Wiress TX. 4 Connect the DC power cable Wireless TX. Note:
The wireless speakers may not receive the changed channel of trans-
mitter. In this case set the ID as below. Setting an ID of Wireless TX and Wireless RX When the unit is manufactured,the ID is already set. If an interference occurs or you use a new Wireless RX, set a new ID. 1. Set the wireless TX and wireless RX within 50cm of eachother. 2. Turn the Wireless TX and Wireless RX on. 3. Press the ID/CHNNEL (ID./CH.) button of Wireless TX and ID button of Wireless RX at the same time for about 3 sec-
onds. 4. Release the ID/CHNNEL (ID./CH.) button of Wireless TX and ID button of Wireless RX.
- ID is set up. Notes:
If there is a product with a strong electromagnetic field nearby, interference may occur.
Do not operate a portable transmitter (such as a wireless network device) near this product. For nearest Authorized Service Center, Where to buy, Product Assistance, or Customer Assistance Call 1-800-243-0000 (24 hours a day, 365 days per year) and select appropriate options from the menu. Or visit our website at http://www.lgservice.com Wireless speaker connector Power cord LG ELECTRONICS U.S.A., INC. 1000 SYLVAN AVENUE ENGLEWOOD CLIFFS, NJ P/N : 3834RV0052F Issue O Printed in Indonesia Connection
Connect the speakers to the front (right, left) or center speaker connectors at the main set.
Connect the subwoofer to the woofer connector.
Connect the power cord of the Wireless RX to the outlet, then connect the Wireless RX and the rear speaker (right, left) with the speaker cable.
Connect the DC IN connector of the Wireless TX and the Wireless TX (DC 7V OUT) connector at the main set with the DC power cable.
Connect the SOUND SIGNAL connector of the Wireless TX and rear (right, left) speaker of connectors of the main set with the sound signal cable.
Set the distance between this unit and Wireless RX within 10m. Notes:
Optimum performance can be implemented only when the Wireless TX and the Wireless RX within distance of 2m to 10m is used since communication failure may occur if longer distance is used.
Be sure to match the speaker cable to the appropriate terminal on the components: + to + and to . If the cables are reversed, the sound will be distorted and will lack base.
It takes about a few seconds (and may take longer) for the Wireless TX and Wireless RX to communicate with each other.
When the unit is turned off, the Wireless RX is in standby mode
(off) automatically after about 10 seconds.
If the Wireless RX is turned off, the wireless speaker will not func-
tion. About Ferrite Core Be sure to attach the ferrite core to the speaker cables (for connecting to this unit). This ferrite core can reduce noises. How to attach the ferrite core 1 Press the stopper [a] of the ferrite core to open. 2 Wind the cable once on the ferrite core. 3 Close the ferrite core unitl it clicks. Note:
Attach the ferrite core near the unit (Refer to the fig.3 and com-
ment.). The length here is as short as possible. SIGNALID./CH.DC INFront speaker (Right)Front speaker (Left) Center speakerRear speakerRear speakerWireless TXWireless RXDC power cable (Right) (Left)SubwooferSIGNALID./CH.DC INSound signalBlackRedcable
This product uses the FCC Data API but is not endorsed or certified by the FCC