LDS401 Bluetooth module User Manual

Bluetooth Emitter Board Model : BM-LDS401 Part No. : EBR76363001 September 2012 Table of Contents Table of Contents Bluetooth Emitter Board . 1 Introduction . 1 Features and Benefits . 2 Hardware Description . 2 Product Specifications . 3 i Bluetooth Emitter Board Introduction The module is an embedded Bluetooth module based on the BCM20705, standalone Bluetooth baseband processor with an integrated 2.4 GHz transceiver. The module is fully compliant with the Bluetooth radio specification and incorporates new modulation schemes to support 2M and 3 Mbps Enhanced Data Rates (EDRs). The module supports UART and is fully compatible with the host controller interface (HCI) Specification. The module includes serial flash memory, a crystal oscillator, and a Chip antenna. Introduction 1 Wireless Dual-band Network Adapter Features Programmable collaborative coexistence interface Class 1 output power capable Scatternet operation, with up to 4 active piconets

(with background scan and support for ScatterMode) 2M and 3 MBps EDR support High-speed HCI UART transport support

- H4 five-wire UART (four signal wires, one ground wire) Full support for power saving modes Firmware upgrades through runtime RAM, serial flash memory download. Hardware Description The Emitter Board can be built in Magic Remocon system and 3D Glasses system for PDP. Hardware Description 2 Product Specifications Product Specifications Bluetooth + EDR compliant Support for Bluetooth + EDR including the following options:

A whitelist size of 25. Enhanced Power Control HCI Read Encryption Key Size command Full support for Bluetooth 2.1 + EDR additional features:

Secure Simple Pairing (SSP) Encryption Pause Resume (EPR) Enhance Inquiry Response (EIR) Link Supervision Time Out (LSTO) Sniff SubRating (SSR) Erroneous Data (ED) Packet Boundary Flag (PBF) 1Mbit Flash Memory Standard HCI support ( UART ) Integrated RF section Single-ended, 50 ohm RF interface Built-in TX/RX switch functionality TX Class 1 output power capability RX sensitivity basic rate of .88 dBm 20MHz Crystal Oscilator Module is designed to fit following applications TV Blue-ray Disc Player ( BDP ) Set Top Box ( STB ) Monitor Projector Smart Box Product Specifications Physical Characteristics Pin Assignment Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 VCC (3.3V) RTS Uart RX Uart TX Reset CTS 3D Sync GND Dimensions 45(L)x15(W)x5.25(H) mm Weight 2.46 g RF Specification Part Bluetooth Spec Frequency Range Sensitivity Output Power Specification Bluetooth Specification V3.0 2.4 GHz ISM Band

-80 10dBm Max.(GFSK) 8.0dBm Max. (EDR) Support Bluetooth Profile HID , A2DP , AVRCP Input Power Current Consumption Operating Temperature Antenna Interface Crystal Frequency Frequency Channel 3.3V Max 75mA

-10 ~ 60 Chip Antenna UART 20 MHz 79 Approval Statements CE approval Hereby, we declare that this device is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. Restrictions of use: In France, this device must not be used outdoors. FCC approval This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesirable operation. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: BEJLDS401 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

IC approval This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opration est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interfrences, et (2) cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. The host device must be labeled to display the Industry Canada certification number of the module. Contains transmitter module IC: 2703H-LDS401 Le dispositif d'accueil doivent tre tiquets pour afficher le numro de certification d'Industrie Canada du module. Contient module metteur IC : 2703H-LDS401 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dea ler or an experienced radio/ TV technician for help. User information Caution: Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate this equipment. Attention: Toute chang ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'utilisateur `autorit de faire fonctionner cet quipement. IMPORTANT NOTE This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20cm is maintained between the antenna and users. 2) This module may not be co-located with any other transmitters or antennas. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC & IC authorizations. NOTE IMPORTANTE Cet appareil est conforme aux limites de la FCC et IC exposition aux radiations dans un environnement non contrl. Cet appareil doit tre install et utilis avec distance minimum de 20cm entre l'lment rayonnant de cet appareil et l'utilisateur. Cet appareil ne doit pas tre co-

localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes :

1) L 'antenne doit tre installe de telle sorte que 20cm est maintenue entre l'antenne et les utilisateurs 2) Ce module ne peut pas tre co-localiss avec les autres metteurs ou les antennes. Aussi longtemps que deux conditions prcites sont remplies, le test du transmetteur supplmentaires ne seront pas tenus. Toutefois, l'intgrateur OEM est toujours responsable de tester leurs produits finis pour toutes les exigences de conformit supplmentaires avec ce module install. Dans le cas o ces conditions ne peuvent pas tre remplies, alors la FCC et IC autorisations ne sont plus considrs comme valides et l'ID de la FCC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera responsable de rvaluer le produit final, y compris l'obtention de ce module et spare de la FCC et IC autorisations