19 LCD Monitor Users Manual

 

FCC ID : BEJM1940AB APPENDIX F :

USERS MANUAL 1 / 50 Regulatory Information FCC Compliance Statement This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. CE Conformity Notice (for Europe) Products with the CE Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive

(73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms :

EN 55022:1998 ; Radio Frequency Interference EN 55024:1998 EN 61000-3-2 ; Power Line Harmonics EN 61000-3-3 ; Voltage Fluctuations EN 60950 ; Product Safety

; Electromagnetic Immunity NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. TCO95 Congratulations!

You have just purchased a TCO95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products. Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem as far as computers and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic- and climatic-influencing emissions, radioactive waste, etc.), it is vital to conserve energy. Electronic equipment in offices consumes as enormous amount of energy, since it is often routinely left running continuously. What does the environmenal labelling involve?

This product meets the requirements for the TCO95 1 Regulatory Information cont. scheme, which provides for international environmental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Naturckyddsfreningen (The Swedish Society for Nature Conservation), and NUTEK (The National Board for Industrial and Technical Development in Sweden), and SEMKO AB (an international certification agency). The requirements cover a wide range of issues:

environment, ergonomics, usability, emission of electrical and magnetic fields, energy consumption and electrical and fire safety. The environmental demands concern, among other things, restriction on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs

(freons), and chlorinated solvents. The product must be prepared for recycling, and the manufacturer is obliged to have an environmental plan, which must be adhered to in each country where the company implements its operational policy. The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level, in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, along with physical and visual ergonomics and good usability. The following is a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from:

TCO Development Unit Linnegatan 14, S-11494 Stockholm, Sweden FAX +46-8 782 92 07 E-mail (Internet): development@tco.se Current information regarding TCO95 approved and labelled products may also be obtained on the Internet using the address: http://www.tco-info.com/

TCO95 is a co-operative project between:

NUTEK SEMKO Nrings- och teknikutvecklingsverket Naturskydds freningen Environmental requirements Brominated flame retardants are present in printed circuit boards, cabling, casings, and housings, and are added to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame-retardant substances. These are related to another group of environmental toxins, PCBs, and are suspected of giving rise to similar harm, including reproductive damage in fish-eating birds and mammals. Flame retardants have been found in human blood, and researchers fear that they can disturb fetus development. Bio-accumulative1 TCO95 demands require that plastic components weighing more than 25 grams must not contain flame retardants with organically bound chlorine or bromine. Lead can be found in picture tubes, display screens, solder, and capacitors. Lead damages the nervous system and in higher doses causes lead poisoning. The relevant bio-

accumulative TCO95 requirement permits the inclusion of lead, as no replacement has yet been developed. Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant bio-accumulative TCO95 requirement states that batteries may not contain more than 25 ppm

(parts per million) of cadmium. The color-generating layers of display screens must not contain any cadmium. Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic in high doses. The relevant bio-accumulative TCO95 requirement states that batteries may not contain more than 25 ppm of mercury and that no mercury is present in any of the electrical or electronic components concerned with the display unit. CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacture of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the atmosphere, causing increased reception on Earth of ultra-violet light with consequent increased risks of skin cancer (malignant melanoma). The relevant TCO95 requirement: Neither CFCs nor HCFCs may be used during the manufacture of the product or its packaging. 1 Bio-accumulative means that the substance accumulates within living organisms. Shipping Package The packaging material can be recycled, or you can save it to return the monitor to a service center for repair or disposal. CFC Compounds in Distribution Packaging Cushioning material used for shipping finished monitors are not manufactured with nor do they contain any CFC compounds. Design for Disassembly/Recycling These monitors have been designed for easy end-of-life disassembly and recycling. Fasteners are generally of the same type for efficient disassembly. Components made of different materials can be easily separated and plastics have been identified using intermational symbols to aid in recycling. Monitor Disposal WARNING If you need to dispose of a monitor, ask a qualified service representative for the proper procedure. Improper disposal could result in personal injury from implosion. 2 Regulatory Information cont. TCO99 Congratulations!

You have just purchased a TCO99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work

(internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g. acidic and climate-

influencing emissions, radioactive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy. What does labelling involve?

This product meets the requirements for the TCO99 scheme which provides for international and environmental labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet

(The Swedish National Energy Administration). Approval requirements cover a wide range of issues:

environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety. The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy. 3 The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability. Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from:

TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/

Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-

accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium**

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO99 requirement states that batteries, the colour-

generating layers of display screens and the electrical or electronics components must not contain any cadmium. Regulatory Information cont. Mercury**

Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. CFCs (freons) The relevant TCO99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs

(freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO99 requirement permits the inclusion of lead since no replacement has yet been developed.

* Bio-accumulative is defined as substances which accumulate within living organisms

** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative. EPA (U.S.A only) ENERGYSATR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LG Electronics U.S.A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. EPA POLLUTION PREVENTER NOM MARK (Mexico only) GOST MARK Internet Address:http://www.lg.ru LG Electronics (095)742-77-77 BZ03 4 M1740A/M1940A/M2040A User's Guide http://www.lge.com P/NO. : 3828TUL289S(0412-REV00) Printed in Korea Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. Table of Contents Installation and Connection Safety Precautions Accessories Before Connecting to the PC Name and Function of the Parts Connecting to External Devices Connecting to your PC Watching Video Watching TV Input Selection and Tracking Selecting and Adjusting the Screen OSD (On Screen Display) Screen Tracking Order Set/Selects the channel when using the TV Adjusting Screen Color Adjusting the audio function Adjusting the timer function Selecting the options Setting a password To adjust the CAPTION&VCHIP function Closed Captions Adjusting Screen CLOCK/PHASE and Position(only PC) Miscellaneous Troubleshooting Specifications i H S I L G N E A1 A4 A5 A9 A11 A11 A13 A14 A15 A18 A19 A21 A22 A23 A24 A26 A27 A29 A30 A31 A34 Safety Precautions Please read these safety precautions carefully before using Warning Caution If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. If you ignore the caution message, you may be slightly injured or the product may be damaged Precautions in installing the Monitor Warning Keep away from heat sources like electrical heaters.

- Electrical shock, fire, malfunction or deformation may occur. Keep the packing anti-moisture material or vinyl packing out of the reach of children.

- Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children. Do not put heavy objects on the monitor or sit upon it.

- If the monitor collapses or is dropped, you may be injured. Children must pay particular attention. Do not leave the power or signal cable unattended on the pathway.

- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury. Install the monitor in a neat and dry place.

- Dust or moisture can cause electrical shock, fire or product damage. If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the service center.

- If you continue to use without taking proper measures, electrical shock or fire can occur. If you dropped the monitor or the case is broken, turn off the monitor and unplug the power cord.

- If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service center. Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the monitor, or inflammable objects such as paper and matches. Children must pay particular attention.

- Electrical shock, fire or injury can occur. If a foreign object is dropped into the monitor, unplug the power cord and contact the service center. Caution Make sure the monitor ventilation hole is not blocked. Install the monitor in a suitably wide place (more than 10cm from the wall)

- If you install the monitor too close to the wall, it may be deformed or fire can break out due to internal heat. Do not block the ventilation hole of the monitor by a tablecloth or curtain.

- The monitor can be deformed or fire can break out due to overheating inside the monitor. Install the monitor on a flat and stable place that has no risk of dropping the monitor.

- If the monitor is dropped, you may be injured or the monitor may be broken. Install the monitor where no EMI occurs. Keep the monitor away from direct sunlight.

- The monitor can be damaged. A1 H S I L G N E Electrical Power Related Precautions Warning Make sure to connect the power cable to the grounded current.

- You may be electrocuted or injured. Use the rated voltage only.

- The monitor can be damaged, or you may be electrocuted. During a thunder or lightning storm, unplug the power cable or signal cable.

- You may be electrocuted or a fire can break out. Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet. Use a power bar with a grounding terminal designed for exclusive use with the computer.

- A fire can break out due to overheating. Do not touch the power plug with wet hands. Additionally, it the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off.

- You may be electrocuted due to excess moisture. If you dont intend to use the monitor for a long time, unplug the power cable from the monitor.

- Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire. Fix the power cable completely.

- If the power cable is not fixed completely, a fire can break out. Hold the plug when pulling out the power cable. Do not bend the power cord with excessive force or put heavy objects on the power cord.

- The power line can be damaged, which may cause electric shock or fire. Do not insert a conductor (like a metal chopstick) into one end of the power cable while the other end is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into the wall input terminal.

- You may be electrocuted. Caution Do not unplug the power cord while the monitor is in use.

- Electrical shock can damage the monitor. Precautions in Moving the Monitor Warning Make sure to turn off the monitor.

- You may be electrocuted or the monitor can be damaged. Make sure to remove all cables before moving the monitor.

- You may be electrocuted or the monitor can be damaged. A2A2 Safety Precautions Caution Do not shock the monitor when moving it.

- You may be electrocuted or the monitor can be damaged Do not dispose the product-packing box. Use it when you move. Make the panel face forward and hold it with both hands to move.

- If you drop the monitor, the damaged monitor can cause electric shock or fire. Contact with the service center for repair. Precautions in Using the Monitor Warning Do not disassemble, repair or modify the monitor at your own discretion.

- Fire or electric shock accident can occur.

- Contact the service center for check, calibration or repair. Do not spray water on the monitor or scrub with an inflammable substance (thinner or benzene). Fire or electric shock accident can occur Keep the monitor away from water.

- Fire or electric shock accident can occur. Caution Do not put or store inflammable substances near the monitor.

- There is a danger of explosion or fire due careless handling of the inflammable substances. When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent scratching. Do not clean with a wet cloth.

- The water can sink into the monitor, which can cause electric shock or serious malfunction. Take a rest from time to time to protect your vision. Keep the monitor clean at all times. Take a comfortable and natural position when working with a monitor to relax the muscles. Take a regular break when working with a monitor for a long time. Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it. Keep the proper distance from the monitor.

- Your vision may be impaired if you look at the monitor too closely. Set the appropriate resolution and clock by referring to the Users Manual.

- Your vision can be impaired. Use authorized detergent only when cleaning the monitor. (Do not use benzene, thinner or alcohol.)

- Monitor can be deformed. A3 Accessories Please check the accessories in the product package.

* The monitor and the accessories can be different from the figures shown here. H S I L G N E Remote Control

/Batteries (AAA x 2) Power Cord Users Manual/

Cards/Driver Diskette D-SUB Signal Cable DVI-D Signal Cable Audio Cable (PC) Back cap Inserting batteries into remote controller. 1. Take out the battery cap. 2. Insert the battery with correct polarity (+/-). 3. Close the battery cap. You can use a remote controller 7 meter distance and 30 degree (left/right) within the receiving unit scope. Dispose of used batteries in the recycle bin to prevent environmental pollution. A4A4 Before Connecting to the PC Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Unfolding the stand base Place the product with its front facing downward on a cushion or soft cloth. Hold down the release button inside the stand and strongly pull out the stand with your two hands. The stand won't move if you don't press release button. A5 To arrange the cables After connecting the cables neatly, arrange the cables to the Cable Holder as shown in the following figure. H S I L G N E A u d i o R L Y P b P r A N T I N D A u d A u d i o R L Y P b P r A N T I N D P C A u d i o Cable Holder Push the back cap shown in the following figure. Back Cap N o t e For remove the back cap, Pull it shown in the following figure. A6 Name and Function of the Parts Name of the Remote Controller Buttons Mute button Input Select Button TV/AV Button

(See next page) Menu Button Exit Button Volume Button Set Button Channel Number Select Button Operational at the TV mode only Sound Mode Select Select the sound mode

: MONO/STEREO/SAP Video Operation Button Applicable for LG products only Power On/Off Button Sleep Button When watching AV//TV

- The monitor will be automatically turned off after a certain period of time. Press this button repetitively to select an appropriate time duration PSM Button When watching AV/HDTV/TV

- Automatically adjusts the image. Press this button repetitively to set the intended screen. (See A27) Channel Up/Down Button Auto Channel Button TV: Automatic TV channel setup PC: Automatic adjustment function

(Operational for the analog signal only) CAPTION Button

(See A33) A7A7 H S I L G N E TV/AV Button This button will be enabled only when you selected the TV/AV signal. The signal type will be changed with the following order. Set the signal type you want. TV AV S-Video Component Input Select Button If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the button. INPUT SELECT TV AV S-Video Component RGB DVI 1. PIP (Picture in Picture) Button The sub-screen moves to the next mode whenever you press this button.

: Small -> Medium -> Large -> Off 2. POP (Picture out Picture) Button The sub-screen moves to the next mode whenever you press this button.

: POP ON -> PBP(FULL) -> PBP(4:3) -> OFF POP ON PBP (FULL) PBP (4:3) A8 Name and Function of the Parts 3. Swap Button You can swap the main screen and the sub-screen when the PIP/POP/PBP function is used.. SWAP SWAP When 'Input Signal 1' comes on in the main screen, only 'Input Signal 2' can be displayed on the sub-screen. On the contrary, if the main screen displays 'Input Signal 2', the sub-screen can display 'Input Signal 1' only. You can swap 'Input Signal 1' and 'Input Signal 2' using the SWAP button.

<Table of PIP/POP/PBP Function Support>

DVI RGB TV AV1 AV2 S-Video DVI RGB TV AV1 AV2 S-Video Inserting batteries into remote controller. 1. Take out the battery cap. 2. Insert the battery with correct polarity (+/-). 3. Close the battery cap. You can use a remote controller 7 meter distance and 30 degree (left/right) within the receiving unit scope. Dispose of used batteries in the recycle bin to prevent environmental pollution. A9 Rear View Audio R L Y Pb Pr ANT IN D PC Audio Audio R Audio L S-Video H S I L G N E Audio L R Y Pb Pr ANT IN D PC Audio Theft prevention locking device Power Cord Connector : Connect the power cord AV Input Terminal TV Tuner Jack: Connect the antenna. DVI Signal Connector D-SUB Analogue Signal Connector Audio Jack :Connect to the jack in the PC sound card. A10 Name and Function of the Parts AV Input Terminal Audio R Audio L S-Video AV(CVBS) Input Terminal(Audio) AV(CVBS) Input Terminal(Video) S-Video Input Terminal Headphone/Earphone Connection Terminal Connecting the sound card output terminal Make sure to check the sound card connection terminal in the PC before connecting to the monitor. If the PC sound card supports both Speaker Out and Line Out, change it to Line Out by setting the jumper or the PC application. (For more details, refer to the sound card users manual.)

- Speaker Out : The terminal connected to the speaker that is not equipped with an amplifier.

- *Line Out : The terminal connected to the speaker equipped with an amplifier. If Audio Out in the PC sound card has only Speaker Out, reduce the PC volume. This monitor is integrated with an amplifier. A11 Connecting to External Devices When Connecting to your PC First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable. A B C When connecting with the DVI signal input cable. When connecting with the D-SUB signal input cable. (IBM compatible PC) When connecting with the D-SUB signal input cable. (Macintosh) Rear side of the product ud o Audio L S-Video Audio R L Y Pb Pr ANT IN D PC Audio H S I L G N E ANT IN PC Audio A B PC C MAC Macintosh Adapter (Optional) Use the standard Macintosh adapter since an incompatible adaptor is available in the market. (Different signaling system) Connect the power cord. Audio R Audio L S-Video ANT IN D PC Audio Rear side of the product

* When connecting to a wall outlet. A12 Connecting to External Devices Turn on power by touching the Power On/Off sensor on the product. Power On/Off sensor Turn on the PC. Select an input signal. Press the Input Select button on the remote controller to select the input signal. Or, press the SOURCE button at the front side of the monitor. A B When connecting with a DVI signal input cable. Select DVI When connecting with a D-SUB signal input cable. Select RGB INPUT SELECT TV AV S-Video Component RGB DVI How to connect to two computers. N o t e Connect the signal cables (DVI and D-Sub) to each computer. Press the SOURCE button in a remote controller to select the computer to use. Directly connect to a grounded power outlet on the wall or a power bar with a ground wire. A13A13 When watching VCR Connect the video cable as shown in the below figure and then connect the power cord

(See page A12). A When connecting with an RCA cable. Connect the input terminal with a proper color match. (Video Yellow, Sound (left) White, Sound (right) Red) H S I L G N E Red White Yellow Audio R Audio L S-Video RCA Cable

(Not included) Side of the Product R W Y AUDIO OUT VIDEO OUT VCR B When connecting with an S-Video cable. Connect to the S-Video input terminal to watch high image quality movies. Red White Audio R Audio L S-Video RCA Cable

(Not included) S-Video Cable

(Not included) R W Side of the Product Select an input signal. Press the SOURCE button on the remote controller to select the input signal. Or, press the SOURCE button at the front side of the monitor. AUDIO OUT VIDEO OUT VCR A B When connecting with a RCA cable. Select AV When connecting with a S-Video cable. Select S-Video INPUT SELECT TV AV S-Video Component RGB DVI A14 Connecting to External Devices When watching DVD Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page A12). A When connecting with an Comonent cable. Connect the input terminal with a proper color match. Audio R L Y Pb Pr Back of the Product R e d W h i t e G r e e n l B u e R e d Video Cable

(optional) Audio Cable

(optional) DVD B When connecting with an S-Video cable. Connect to the S-Video input terminal to watch high image quality movies. Red White Audio R Audio L S-Video RCA Cable

(Not included) S-Video Cable

(Not included) AUDIO OUT R W VIDEO OUT Side of the Product DVD Select an input signal. Press the SOURCE button on the remote controller to select the input signal. Or, press the SOURCE button at the front side of the monitor. INPUT SELECT TV AV S-Video Component RGB DVI A B When connecting with a Component cable. Select Component When connecting with a S-Video cable. Select S-Video A15 When watching TV See if the antenna cable is connected at the rear side of the monitor and then, connect the power cord . H S I L G N E Audio R Audio L S-Video Audio R L Y Pb Pr ANT IN D PC Audio Rear side of the Product Audio R L Y Pb Pr ANT IN PC Audio Antenna Cable

(Not Included) Select an input signal. Press the SOURCE button on the remote controller to select the input signal. Or, press the SOURCE button at the front side of the product. INPUT SELECT TV AV S-Video Component RGB DVI Select TV A16 Selecting and Adjusting the Screen Name of the Buttons in the Screen Adjustment Unit SOURCE MENU PR <<

< VOL >

AUTO/SELECT CH Power LED This indicator lights up blue when the display operates normally. If the display is in DPM (Energy Saving) mode, this indicator color changes to amber. Power On/Off sensor Touch the button to turn on the power. Touch the button again to turn it off. MENU Button Use this button to show/hide the OSD (On Screen Display) menu screen. OSD Select /

Adjust Button Use these buttons to select an icon or adjust the setting in the OSD screen.

Use these buttons to directly control brightness and contrast of the PC signal

(RGB, DVI) Use these buttons to control the channel for the TV signal.

Adjust the volume. A17 Name of the Buttons in the Screen Adjustment Unit AUTO/SELECT Button

[For PC Analogue signal-RGB]

Auto In progress

[For TV]

Auto In progress 0

50%

H S I L G N E

[Other signals]

The current signal and mode information will be displayed. SOURCE Button

Select the input signal TV AV S-Video Component RGB DVI Television Composite video Separate Video Component signal D-SUB analog signal DVI digital signal INPUT SELECT TV AV S-Video Component RGB DVI The unit that receives the signal from the remote controller. A18 Selecting and Adjusting the Screen OSD Menu Icon Function Description Set/Selects the channel. STATION PICTURE SOUND TIMER SPECIAL SCREEN PIP/POP/PBP Adjusts screen brightness, contrast and color that you prefer. Adjusts the audio function. Adjusts the timer function. Adjusts the screen status according to the circumstances. Adjusts the screen video. Adjusts PIP/POP/PBP mode function. Note OSD(On Screen Display) The OSD function enables you to adjust the screen status conveniently since it provides graphical presentation. A19 How to adjust the OSD (On Screen Display) screen. H S I L G N E Pops up the menu screen Move where you want to adjust Select a menu icon Adjust the status Save/Select adjustment Exit from the menu screen. Use the remote controller to adjust the OSD screen. 1 2 3 4 5 6 Press the MENU Button, then the main menu of the OSD appears. To access a control, use the DD/ EE Buttons. When the icon you want becomes highlighted, press the SET Button. Use the DD/ EE/ FF / GG Buttons to adjust the item to the desired level. Accept the changes by pressing the SET Button. Exit the OSD by pressing the EXIT Button. How to adjust the screen automatically. You need to adjust the screen display when connecting the product to a new computer or changing the mode. Refer to the following section to set an optimal product screen. Press the AUTO/SELECT button (AUTO button in a remote controller) in the PC analog signal. Then, an optimal screen status will be selected that fits into the current mode. If adjustment is not satisfactory, you need to adjust screen position, clock and phase in the OSD menu. A20 Auto In progress Selecting and Adjusting the Screen Set/Selects the channel when using the TV STATION EZ Scan Manual Prog MENU Prev EZ Scan STATION EZ Scan Manual Prog G To start To automatically search the available TV channels. MENU Prev To Start Press G button to start automatic programming. all available TV channels are searched and stored automatically. To stop auto CH progess, press the MENU button. Wait for auto CH progess to complete the channel search cycle before choosing a channel. The TV scans for over-the-air channels and then channels provided by a cable service. Manual Prog. STATION EZ Scan Manual Prog MENU Prev G CH 3 Memory Channel Memory /

Erase Press G button and then use F / G button to select the channel. User can do manual channel selection and store or erase individual channels. Press DD / EE button and then use G button to select a channel you want to add to memory or erase. Press the E button and then use F / G button to select Memory(add) or Erase(delete). A21 Adjusting the picture function EZ Video PICTURE EZ Video ACC G

Dynamic Standard Mild Game User H S I L G N E TV/AV1/AV2/S-Video input only MENU Prev The EZ Video function automatically adjusts the screen image quality depending on the AV/TV usage environment. Dynamic : Select this option to display with a sharp image. Standard : The most general and natural screen display status. Mild : Select this option to display with a mild image. Game : Select this option to enjoy dynamic image when playing a game. User : Select this option to use the user-defined settings. PICTURE EZ Video ACC Contrast Brightness Color Sharpness Tint Dynamic Standard Mild Game User

66 80 55 54 G MENU Prev Contrast To adjust the contrast of the screen. Brightness To adjust the brightness of the screen. Color To adjust the color to desired level. Sharpness To adjust the cleaness of the screen. Tint To adjust the tint to desired level. (only 60Hz signal) ACC PICTURE EZ Video ACC G

Warm Normal Cool MENU Prev Selecting a factory setting color set. Warm : Slightly reddish white. Normal : Slightly bluish white. Cool : Slightly purplish white. Note If the input is RGB PC(D-Sub analogue)/DVI PC(DVI Digital), the adjustable items in the ACC function are color temp (9300K / 6500K). If the PSM' setting in the Picture menu is set to Dynamic, Standard, Mild or Game the subsequent menus will be automatically set. A22 Selecting and Adjusting the Screen Adjusting the picture function CSM PICTURE RGB PC / DVI PC input only EZ Video ACC G

6500K 9300K User MENU Prev PICTURE EZ Video ACC Contrast Brightness Red Green Blue 6500K 9300K User<

G 72 58 99 100 100 MENU Prev 6500K/9300K Selecting a factory setting color set. 6500K: Slightly reddish white. 9300K: Slightly bluish white. User : Select this option to use the user-defined settings. Contrast To adjust the contrast of the screen. Brightness To adjust the brightness of the screen. Red / Green / Blue Set your own color levels. A23 Adjusting the sound function EZ Audio SOUND EZ Audio Balance AVL SRS WOW MENU Prev G

Flat Music Movie Speech User H S I L G N E Flat The most commanding and natural audio. Music Select this option to enjoy the original sound when listening to the music. Movie Select this option to enjoy sublime sound. Speech Select this option to watch sports broadcasting. The best sound tone quality will be selected automatically depending on the video type that you're currently watching. SOUND EZ Audio Balance AVL SRS WOW MENU Prev Flat Music Movie Speech User

Equalizer G 0.1 0.5 1.5 5.0 10.0 kHz Equalizer 1) Press the MENU button and then use DD / EE button to select the SOUND menu. 2) Press the GG button and then use DD / EE button to select the EZ Audio menu. 3) Press GG button and then use DD / EE button to select User. 3) Press GG button and then use F / G button to select the band. Then press the DD / EE button to adjust the band level. Balance AVL SRS WOW Use this function to balance sound from the left and right speakers. To adjust uneven sound volumes across all channels or signals automatically to the most appropriate level. To use this feature, select ON. (It is adjustble to the TV input signal only.) Set the SRS WOW menu on. The SRS WOW function plays back the mono or stereo sound input with the dynamic surround effects. It will provide rich and profound sound tone. If you set the SRS WOW on, user audio setting can not be adjusted. Note When connected to your computer and the 'EZ Audio' setting in the audio menu is one of Flat, Movie, Music or Speech, the available menus are Balance, SRS WOW . A24 Selecting and Adjusting the Screen Adjusting the timer function Clock TIMER Clock Off timer On timer Auto off MENU Prev Auto Clock Setup This function is used to set up of current time. You must set the time correctly before using on/off timer function. 1) Press the MENU button and then use DD / EE button to select the TIMER menu. 2) Press the GG button and then use DD / EE button to select the Clock menu. 3) Press GG button and then use DD / EE button to select Auto. 4) Press GG button and then use FF / GG button to select the time zone for your viewing area. Your choices are : AUTO, E.S.T(Eastern Standard Time), C.S.T(Central Standard Time), M.S.T(Mountain Standard Time), P.S.M(Pacific Standard Time), Alaska and Hawaii. 5) Press EE button and then use FF / GG button to set PBS channel. 6) Press EE button and then use FF / GG button to set D.ST (Daylight Savings Time) Auto, off or On, depending in whether or not your viewing area observes Daylight Savings Time. 7) Press SET button to save. Manual Clock Setup You must set the time correctly before using on/off timer function. 1) Press the MENU button and then use DD / EE button to select the TIMER menu. 2) Press the GG button and then use DD / EE button to select the Clock menu. 3) Press GG button and then use DD / EE button to select Manual. 3) Press GG button and then use DD / EE button to set the hour(01~12). 4) Press GG button and then use DD / EE button to set the minutes(00~59). 5) Press GG button and then use DD / EE button to set the morning(AM) or afternoon(PM). 6) The default value is __:__. Off / On Timer The off timer automatically switches the set to Off Mode at the pre-set time. 1) Press the MENU button and then use DD / EE button to select the TIMER menu. 2) Press the GG button and then use DD / EE button to select Off Timer or On Timer. 3) Press the GG button and then use DD / EE button to set the hour(01~12). 4) Press the GG button and then use DD / EE button to set the minutes(00~59). 5) Press GG button and then use DD / EE button to set the morning(AM) or afternoon(PM). 6) Press the GG button and then use DD / EE button to select On or Off. 7) Only ON Timer function; Press the GG button and then DD / EE button to adjust volume level and channel number. 8) Press the SET/MENU button to save. Auto Off

(TV input only) If Auto Off is active and there is no input signal, the TV swithchs to off mode automatically after 10 minutes. 1) Press the MENU button and then useDD / EE button to select the Auto Off menu. 2) Press the GG button and then useDD / EE button to select On or Off. 3) Press the SET/MENU button to save . N o t e In the event of power interruption (disconnection or power failure), the clock must be reset. Two hours after the set is switched on by the on time function it will automatically switch back to off mode unless a button has been pressed. Once the on or off time is set, these functions operate daily at the preset time. Off Timer function overrides On Timer function if they are set to the same time. The set must be in Off Mode mode for the On timer to work. A25 Adjusting the special function SPECIAL Input Key lock language Power indicator Transparency Zoom Reset E MENU Prev G

TV Video S-Video Component RGB DVI H S I L G N E If you press the ?? button once, the following Input Signal Window will appear. Select the signal type you want using the DD / EE button. key lock Use the DD / EE buttons to select ON or OFF. It can be set up so that it can only be used with the remote control. This feature can prevent unauthorized viewing. In order to lock the OSD screen adjustment, set the Key lock tab to the 'on' position. In order to unlock it, do the following :

1) Push the MENU button on the remote control and set Key lock to the 'off' position. Language To choose the language in which the control names are displayed. Power Indicator Use this function to set the power indicator on the front side of the monitor to ON or OFF. If you set OFF, it will go off after 15 seconds when the power is turned on. If you set ON at any time, the power indicator will automatically be turned on. Transparency Use this function to adjust the transparency of the OSD menu screen. Zoom SPECIAL Input Key lock language Power indicator Transparency Zoom Reset E MENU Prev Zoom 0 H Position 0 V Position 0 G Use this function to zoom in the screen. When you turn the product off and on again, the default screen size will be restored. Press the GG button to display the submenu for Zoom.

* If the zooming value is set to

'0', vertical and horizontal positioning cannot be adjusted. Reset Use this function to reset the monitor to the factory default. However, language selection and Volume will not be initialized. A26 Selecting and Adjusting the Screen Closed Captions Closed captioning is a process which converts the audio portion of a television program into written words which then appear as subtitles on the television screen. Closed captions allow viewers to read the dialogue and narration of television programs. Using Closed Captions Captions are the subtitles of the dialogue and narration of television programs. For prerecorded programs, program dialogue can be arranged into captions in advance. It is possible to caption a live program by using a process called real-time captioning, which creates captions instantly. Real-time captioning is normally done by professional reporters using a machine shorthand system and computer for translation into English. Captioning is an effective system for the hearing-impaired, and it can also aid in teaching language skills. Caption Tips 1. Not all TV broadcasts include closed caption signals. 2. Sometimes TV stations broadcasts four different caption signals on the same channel. By selecting From CC1 ~ CC4, TEXT1 ~ TEXT4 you can choose which signal you view CC1 is usually the signal with the captions, while Another mode might show demonstration or programmimg information. 3. Your TV might not receive caption signals normally in the following situations. Poor reception conditions are encountered :

- IGNITION :

Picture may flutter, drift, suffer from black spots, or horizontal streaking. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances.

- GHOSTS :

Ghosts are caused when the TV signal splits and follows two paths. One is the direct path and the other is reflected off tall buildings, hills or other objects. Changing the direction or position of the antenna may improve reception.

- SNOW :

If your receiver is located at the weak, fringe area of a TV signal, your picture may be marred by small dots. It may be necessary to install a special antenna to improve the picture. An old, bad or illegally recorded tape is playing. Strong, random signals from a car or airplane interfere with the TV signal. The signal from the antenna is weak. The program wasn't captioned when it was produced, transmitted, or taped. Captions

(only TV mode) Use the DD / EE buttons to select captions.

[Remote Control]

Press the CC button repeatedly to display the caption option as shown below. Press the SET button to select the caption option. Off On EZ Mute

* EZ Mute Caption / Text If sound is on, the caption will be off. On the contrary, if sound is off, the caption will be on. Use the DD / EE buttons to select caption mode. Text services give a wide variety of information on all kind of subjects(ex. captioned program lists, weather forecasts, stock exchange topics, news for hearing-impaired....) on up to half of the TV screen. But not all stations offer text services, even though they might offer captioning. In the event you are receiving a poor signal, an empty black box may appear and disappear, even when the text mode is selected. This is a normal when receiving a poor signal. This TV is programmed to remember the CAPTION / TEXT mode it was last set to, when you turn the power off. A27 V-CHIP rating and categories

- Rating guidelines are provided by broadcast station. Most television programs and television movies can be blocked by TV rating and/or individual categories. Movies that have been shown at the theaters or direct-to-video movies use the Movies Rating System(MPAA) only. For movies previously shown in theaters. H S I L G N E G

Unblocked G & above PG & above PG-13 & above R & above NC-17 & above X G

General Children PARENTAL MPAA Age block Content block Set password Lock on/off Canadian MENU Prev PARENTAL MPAA Age block Content block Set password Lock on/off Canadian MENU Prev MPAA

: General audience

: Parental guidance suggested MOVIE Ratings :

- Unblocked

- G&above

- PG&above

- PG-13&above : 13 years and up

- R&above

- NC-17&above : 17 years and up

- X If you set PG-13&above, G and PG movies will be available : PG-13, R, NC-17, and X will be blocked.

: Restricted

: Adult Age Block GENERAL TV Rating :

- Unblocked

- TV-G&above : General audience / Individual categories do not apply.

- TV-PG&above : Parental guidance suggested

- TV-14&above : 14 years and up

- TV-MA

: Mature audience CHILDREN TV Rating :

- Unblocked

- TV-Y&above : Youth/Individual content

- TV-Y7 categories do not apply.

: Youth, 7 years and up. PARENTAL MPAA Age block Content block Set password Lock on/off Canadian MENU Prev G

Dialoge Language Sex scene Violence F Violence No rating Content Block CONTENT Categories :

- Dialogue(sexual dialogue)

: Applies to TV-PG&above, TV-14.

- Language(adult language)

: Applies to TV-PG&above, TV-14&above, TV-MA.

- Sex (sexual situations)

: Applies to TV-PG&above, TV-14&above, TV-MA.

- Violence

: Applies to TV-PG&above, TV-14&above, TV-MA.

- F Violence(fantasy violence)

: Applies only to TV-PG&above. A28 Selecting and Adjusting the Screen Selecting the options

(To adjust the CAPTION & VCHIP function) PARENTAL MPAA Age block Content block Set password Lock on/off Canadian MENU Prev Enter code

G Set Password This menu is to be used to change password. Once the correct current password is entered using the number panel in a remote control, the window for new password will appear. Enter your choice of new four-digit password. Setting a password You control access to the parental controls with a password. The default password is '0000'. You can change the password to any four-digit number. 1. Open the OSD. -> Press the DD / EE buttons to select the Special menu, then press the GG button to open the menu. -> Press the DD / EE buttons to select the Parental sub-menu, then press the GG button to open the sub-menu. 2. Use the number pad to enter your password when prompted. If you have not set a passwod, enter 0000. If you are unable to correct the problem yourself, contact the service center. 3. Press the DD / EE buttons to select the Set Password sub-menu, then press the GG button to change the setting. Use the number button pad to enter a new four-digit password when prompted. 4. Re-enter the new four-digit password when prompted. Enter code

Enter new code

Enter new code

Re-enter code

Lock On/Off To select the VCHIP function ON/OFF. PARENTAL MPAA Age block Content block Set password Lock on/off Canadian MENU Prev G

Off On A29 Selecting the options

(To adjust the CAPTION & VCHIP function - Canadian Only) V-CHIP rating and categories (Optional) - Canadian Rating System

- Rating guidelines are provided by broadcast station. Most television programs and television movies can be blocked by TV rating and/or individual categories. H S I L G N E Canadian PARENTAL MPAA Age block Content block Set password Lock on/off Canadian MENU Prev G

English Franais English MOVIE Ratings :

- Unblocked

- C&Above

- C8&Above

- G&Above

- PG&Above

- 14+&Above : 14 years and up

- 18+

: Under 8 years

: 8 years and up

: General audience

: Parental guidance suggested

: Adult Franais MOVIE Ratings :

- Unblocked

- G&Above

- 8 ans +

- 13 ans +

- 16 ans +

- 18 ans +

: General audience

: 8 years and up

: 13 years and up

: 16 years and up

: 18 years and up A30 Selecting and Adjusting the Screen Adjusting Screen CLOCK/PHASE and Position(only PC) SCREEN ARC Auto-configure Clock Phase Position ARC Auto-

Configure Clock Phase Position SCREEN ARC Auto-configure Clock Phase Position MENU Prev G

Auto Full 4:3 Spectacle Zoom1 Zoom2 To select the image size of the screen. Full / 4:3 / 16:9 / Zoom In only TV/AV1/AV2/S-Video 4:3 aspect ratios is not available in 20 inches model. FULL/1:1 in DVI/RGB This function is suitable for analoge singnal input only. This button is for the automatic adjustment of the screen position, clock and phase. To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. SCREEN ARC Auto-configure Clock Phase Position G MENU Prev F D E G Horizontal Vertical 40 53 To adjust position of the screen. Press the GG button to display the submenu for position. Moving the screen position horizontally. FF Left GG Right DD Up EE Down Moving the screen position vertically. A31 PIP/POP/PBP Mode (Multiple Screen) Functions PIP/POP/PBP On/Off Source Size Image Sound Position Swap MENU Prev G

Off PIP POP PBP On/Off PIP After selecting PIP/POP/PBP in the PIP On/Off menu, the following menu items can be adjusted. H S I L G N E POP After selecting PIP/POP/PBP in the POP On/Off menu, the following menu items can be adjusted. PBP After selecting PIP/POP/PBP in the PBP On/Off menu, the following menu items can be adjusted. Source Size Image To select an input signal for PIP/POP/PBP. To adjust the size of the PIP/POP/PBP screen. (PIP : Small, Medium, Large / PBP : Full, 4:3) To adjust the image of the PIP/POP/PBP screen; Press the G button to display the submenu for PIP/POP/PBP image. Use the F / G buttons to adjust the item to the desired level. The items of the sub-menu may vary depending on the type of the source. PIP/POP/PBP On/Off Source Size Image Sound Position Swap MENU Prev G Contrast 30 Brightness 50 50 Color Contrast Adjust PIP/POP/PBP screen contrast. Brightness Adjust PIP/POP/PBP screen brightness. Colour Adjust the PIP/POP/PBP screen colour.

* The sub-menu can differ according to the type of the input signal. Sound To turn the PIP/POP/PBP sound on/off. A32 Selecting and Adjusting the Screen PIP/POP/PBP Mode (Multiple Screen) Functions Position PIP/POP/PBP On/Off Source Size Image Sound Position Swap MENU Prev Swap PIP/POP/PBP On/Off Source Size Image Sound Position Swap MENU Prev

Off On G G To adjust the position to PIP screen. To switch the main-

screen and sub-screen in PIP/POP/PBP mode. PIP POP PBP SWAP SWAP A33 H S I L G N E Troubleshooting No image is displayed Is the product power cord connected?

See if the power cord is properly connected to the outlet. Does the power LED is turned on?

See if the power switch is turned on. Power is on, power LED is green but the screen appears extremely dark. Does the power LED look amber?

Does the 'Out of Range' message appear?

Does the 'Check Signal Cable'

message appear?

Adjust brightness ( ) and contrast ( ) again. If the product is in power saving mode, move the mouse or press any key. The signal from the PC (video card) is out of the vertical or horizontal frequency range of the product. Adjust the frequency range by referring to the Specifications in this manual.

* Maximum resolution 17, 19 inches : 1280 x 1024 @75Hz 20.1 inches : 1600 x 1200 @60Hz The signal cable between PC and product is not connected. Check the signal cable. Press the 'SOURCE' button in the remote controller to check the input signal.

'Unknown Product' message appears when the product is connected. Install the product driver, which is provided with Did you install the driver?

the product, or download it from the web site.

(http://www.lge.com) See if the plug&play function is supported by referring to the video card user manual.

'Controls Locked' message appears. The Controls locked message appears when pressing local key. The control locking function prevents unintentional OSD setting change due to careless usage. To unlock the controls.(You can only set this function using the remote controller.) N o t e

* Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second. The unit is Hz.

* Horizontal frequency: The horizontal interval is the time to display one vertical line. When the 1 is divided by horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal frequency. The unit is kHz. A34 Troubleshooting The screen image looks abnormal. Is the screen position wrong?

Do thin lines appear on the background screen?

Horizontal noise appears or the characters look blurred. D-SUB analog signal Press the AUTO button in the remote controller to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Position menu in OSD . See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the Control Panel Display Setting menu. D-SUB analog signal Press the AUTO button in the remote controller to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Clock menu in OSD. D-SUB analog signal Press the AUTO button in the remote controller to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Phase menu in OSD. Unable to adjust the horizontal /

vertical position in the Zoom menu. See if the Zoom value is set to 0. If it is, you cannot adjust the H/V Position value. Screen size is automatically adjusted when connected to the PC. If the screen size is not full when connected to the PC, execute the PIP/POP/PBP to change to full screen mode. No sound appears in the TV channel display window. See if the TV sound is set to mono. If it is, the sound will not be displayed. Brightness differs in the main and sub screen when connected to the PC. The screen is displayed abnormally. You cannot adjust brightness in the PIP/POP/PBP Screen menu for the sub-screen among PIP/POP/PBP menus. Therefore, brightness can be different for the sub-screen. The proper input signal is not connected to the signal port. Connect the signal cable that matches with the source input signal. No sound appears in the TV channel display window. See if the TV sound is set to mono. if it is, the sound will not be displayed. A35 The audio function does not work. No sound?

See if the audio cable is connected properly. Adjust the volume. See if the sound is set properly. No sound is available when the PIP/POP/PBP mode is engaged. See if the sound is set to On in the PIP/POP/PBP menu. Sound is too dull. Sound is too low. Select the appropriate equalize sound. Adjust the volume. H S I L G N E The TV function does not work. The TV signal is not being received. See if you have selected the proper channel mode. Use the automatic channel setup function. See if the TV antenna is properly connected. Screen color is abnormal. Screen has poor color resolution (16 colors). Set the number of colors to more than 24 bits (true color) Select Control Panel Display Settings Color Table menu in Windows. Screen color is unstable or mono-

colored. Check the connection status of the signal cable. Or, re-insert the PC video card. Do black spots appear on the screen?

Several pixels (red, green, white or black color) may appear on the screen, which can be attributable to the unique characteristics of the LCD panel. It is not a malfunction of the LCD. After-image appears on the product. After-image appears when the product is turned off. If you use a fixed image for a long time, the pixels may be damaged quickly. Use the screensaver function. A36 Specifications

[17 inches]

LCD Panel Screen Type Pixel Pitch 17 inches (431.8mm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size: 431.8mm 0.264mm Video Signal Max. Resolution 1280X1024 @75Hz Recommended Resolution 1280X1024 @60Hz Horizontal Frequency D-SUB : 30 - 83 kHz DVI-D : 30 - 71 kHz Vertical Frequency 56 - 75 Hz Input Connector Power Tilt Synchronization Type Separate/Composite/SOG (Sync On Green)/Digital Rated Voltage Power Consumption 15-pin D-Sub type, DVI-D (digital), S-Video, composite video, Scart AC 100-240V~ 50/60Hz 1.0A Normal operation: 55W Power saving preparation state: 4W Power saving state: 4W Power switch off: 2W Tilt Range Tilt Stand

-5~25 Attached Dimension/Weight Size (WxLxH) Weight (excl. package) 6.65 kg (14.66 lbs) 501.5mm x 158.2 mm x 500.3 mm Environmental Conditions Operational Condition Temperature: 10C ~ 35C , Humidity: 10% ~ 80%

Storage Condition Temperature: -20C ~ 60C , Humidity: 5% ~ 95%

A37

[19 inches]

LCD Panel Screen Type Pixel Pitch 19 inches (482.6mm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size: 482.6mm 0.294mm Video Signal Max. Resolution 1280X1024 @75Hz H S I L G N E Recommended Resolution 1280X1024 @60Hz Horizontal Frequency D-SUB : 30 - 83 kHz DVI-D : 30 - 71 kHz Vertical Frequency 56 - 75 Hz Input Connector Power Tilt Synchronization Type Separate/Composite/SOG (Sync On Green)/Digital Rated Voltage Power Consumption 15-pin D-Sub type, DVI-D (digital), S-Video, composite video, Scart AC 100-240V~ 50/60Hz 1.0A Normal operation: 60W Power saving preparation state: 4W Power saving state: 4W Power switch off: 2W Tilt Range Tilt Stand

-5~25 Attached Dimension/Weight Size (WxLxH) Weight (excl. package) 7.75 kg (17.09 lbs) 542.5mm x 222.8 mm x 541.4 mm Environmental Conditions Operational Condition Temperature: 10C ~ 35C , Humidity: 10% ~ 80%

Storage Condition Temperature: -20C ~ 60C , Humidity: 5% ~ 95%

A38 Specifications

[20.1 inches]

LCD Panel Screen Type Pixel Pitch 20.1 inches (510mm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel Visible diagonal size: 510mm 0.2805mm Video Signal Max. Resolution 1600X1200 @60Hz Recommended Resolution 1600X1200 @60Hz Horizontal Frequency D-SUB : 30 - 92 kHz DVI-D : 30 - 80 kHz Vertical Frequency 56 - 85 Hz Input Connector Power Tilt Synchronization Type Separate/Composite/SOG (Sync On Green)/Digital Rated Voltage Power Consumption 15-pin D-Sub type, DVI-D (digital), S-Video, composite video, Scart AC 100-240V~ 50/60Hz 1.2A Normal operation: 70W Power saving preparation state: 4W Power saving state: 4W Power switch off: 2W Tilt Range Tilt Stand

-5~25 Attached Dimension/Weight Size (WxLxH) Weight (excl. package) 8.7 kg (19.18 lbs) 575.1mm x 221.1 mm x 557.5 mm Environmental Conditions Operational Condition Temperature: 10C ~ 35C , Humidity: 10% ~ 80%

Storage Condition Temperature: -20C ~ 60C , Humidity: 5% ~ 95%

A39 H S I L G N E Preset mode 8 9 10 11 12 13 VESA VESA MAC MAC VESA VESA 1024 x 768 1024 x 768 1152 x 870 1152 x 900 1280 x 1024 1280 x 1024 Horizontal Frequency

(kHz) 48.363 60.123 68.681 61.805 63.981 79.980 Vertical Frequency

(Hz) 60 75 75 66 60 75 Preset mode 11 12 13 14 15 16 17 18 19 VESA VESA MAC MAC VESA VESA VESA VESA VESA 1024 x 768 1024 x 768 1152 x 870 1152 x 900 1280 x 1024 1280 x 1024 1600 x 1024 1600 x 1200 1600 x 1200 Horizontal Frequency

(kHz) 60.020 68.680 68.680 61.800 63.980 79.980 62.110 75.000 73.530 Vertical Frequency

(Hz) 75 85 75 66 60 75 60 60 60 PC Mode Preset Mode

[17, 19 inches]

Preset mode 1 2 3 4 5 6 7 VGA VGA VGA VESA VESA VESA MAC 640 x 350 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 Horizontal Frequency

(kHz) 31.469 31.468 31.469 37.500 37.879 46.875 49.725 Vertical Frequency

(Hz) 70 70 60 75 60 75 75

[20.1 inches]

Preset mode 1 2 3 4 5 6 7 8 9 10 VGA VGA VGA VGA VGA VESA VESA VESA MAC VESA 640 x 350 640 x 480 640 x 480 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 Horizontal Frequency

(kHz) 31.469 31.469 37.500 43.270 31.469 37.880 46.880 53.670 49.720 48.360 Vertical Frequency

(Hz) 70 60 75 85 70 60 75 85 75 60 Mode 18 : Analogue only Mode 19 : Digital only Power LED Mode Normal Operation Pre-power Saving State Power Saving State Power Switch Off Product Blue Amber Amber

A40 Specifications VESA wall mounting VESA wall mounting Connected to another object (stand type and wall-mounted type. This monitor accepts a VESA-compliant mounting interfacepad.optional) For further information, refer to the VESA Wall Mounting Instruction Guide. Theft prevention locking device Audio R Audio L S-Video ANT IN D PC Audio Locking Device Use this locking cable (optional) to prevent theft. A41 H S I L G N E A42 M1740A/M1940A/M2040A User's Guide http://www.lge.com P/NO. : 3828TUL289S(0412-REV00) Printed in Korea Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.