| submitted | available | document details (if available) | source link |
|---|---|---|---|
| May 11 2003 | May 11 2003 |
| various | User Manual | Users Manual | 1.15 MiB | May 11 2003 |
PLASMA MONITOR OWNERS MANUAL MODEL : MU-50PZ90MQ Please read this owners manual thoroughly before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and relate this information to your dealer if you ever require service. Model Number :
Serial Number :
P/NO : 3828VA0410H (RF03GB) Warning WWarning arning WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli-
ance. WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compli-
ance could void the users authority to operate the equipment. WARNING TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 2 Plasma Monitor Safety Instructions Safety Instructions Safety Instructions Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential elec-
trical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product. This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association. 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 9. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. 2. Follow Instructions All operating and use instructions should be followed. 3. Retain Instructions The safety and operating instructions should be retained for future reference. 4. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Water and Moisture Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet base-
ment, or near a swimming pool. 7. Accessories, Carts, and Stands Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manu-
facturer, or sold with the product. Any mounting of the prod-
uct should follow the manufacturers instructions, and should use a mounting accessory recommended by the manufac-
turer. 8. Transporting Product A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by plac-
ing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is pro-
vided or the manufacturers instructions have been adhered to. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Power-Cord Polarization This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety fea-
ture. If you are unable to insert the plug into the outlet, con-
tact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. PORTABLE CART WARNING Owners Manual 3 Safety Instructions Safety Instructions continued Safety Instructions continued 19. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service per-
sonnel. 20. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. b. If the power-supply cord or plug is damaged. If liquid has been spilled, or objects have fallen into the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or the cabinet has been damaged. If the product exhibits a distinct change in performance. c. d. e. f. 21. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the man-
ufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to deter-
mine that the product is in proper operating condition. 23. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. 24. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat. 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting struc-
ture, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-dis-
charge unit, connection to grounding electrodes, and requirements for the grounding electrode. Example of Grounding According to National Electrical Code Instructions Ground Clamp Antenna Lead in Wire Electric Service Equipment NEC - National Electrical Code Antenna Discharge Unit
(NEC Section 810-20) Grounding Conductor
(NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) 15. Lightning For added protection for this product (receiver) during a light-
ning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 4 Plasma Monitor Contents Contents Warnings . 2 Safety Instructions . 3~4 Introduction Controls and Connection Options . 7 Remote Control Key Functions . 8 Installation Installation Instruction . 9~10 External Equipment Connections . 11~14 VCR Setup . 11 Cable TV Setup . 11 External A/V Source Setup . 12 DVD Setup . 12 DTV Setup . 12 PC Setup . 13~14 Operation Turning on the Monitor . 15 Menu Language Selection . 15 Video Menu Options APC (Auto Picture Control) . 16 Manual Picture Control . 16 Auto Color Temperature Control . 16 Manual Color Temperature Control . 16 Audio Menu Options DASP (Digital Auto Sound Processing) . 17 Manual Sound Control . 17 AVL (Auto Volume Leveler) . 17 Time Menu Options Clock Setup . 18 On/Off Timer Setup . 18 Auto Off . 18 Sleep Timer . 18 Security PIP Time Setup . 19 Security Active . 19 Special Menu Options Key Lock . 20 ISM Method . 20 Contents Low power . 20 Security PIP Operation . 21 Menu Rotation For Vertical Viewing . 21 Screen Menu Options Auto Adjustment . 22 Setting Picture Format . 22 Picture Size Zoom . 22 Split Zoom . 23 Screen Position . 23 Manual Configure . 23 Screen Adjustments . 24 Initializing . 24 Selecting Wide VGA/XGA mode . 24 Luminance Noise Reduction . 24 PIP (Picture-in-Picture) Feature Watching PIP . 25 PIP Size . 25 PIP Aspect Ratio . 25 Swapping PIP . 25 Moving PIP . 25 Selecting an Input Signal Source for PIP . 25 Twin Picture Setup Options Watching Twin Picture . 26 Sub Picture Size Adjustment . 26 Swapping the Twin Picture . 26 Selecting a Source for the Twin Picture . 26 External Control Device Setup . 27~32 IR Code . 33~34 Troubleshooting Checklist . 35 Maintenance . 36 Specifications . 37 Setup and Operation Checklist Setup and Operation Checklist Setup and Operation Checklist
(See pages 11~13 for available connection and operational setup options.) 1. Unpack Monitor and all accessories. 5. Turn video source equipment on. 2. Connect all external video and audio equipment. 6. Select viewing source for Monitor. see pages 11 ~ 14. See page 8. 3 Install batteries in remote control. See page 8. 4. Turn Monitor on. See page 15. 7. Fine-tune source image and sound to personal preference or as required by source. See pages 16 ~ 17. 8. Additional features Setup See Contents above. After reading this manual, keep it handy for future reference. Owners Manual 5 Introduction Introduction Introduction What is a Plasma Display Panel (PDP)?
If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160 - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room. Wide Screen The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater. Multimedia Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously. Versatile The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would not fit. The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be accept-
able. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects during the manufacture and operation of this product. Cooling Fan Noise In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operat-
ing and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not suffi-
cient cause for the PDP to be exchanged or returned. 6 Plasma Monitor Controls Controls
- This is a simplified representation of front panel. Here shown may be somewhat different from your monitor. Front Panel Controls Front Panel Controls Introduction ON/OFF I N P U T S E L E C T M E N U V O L . Main Power Button INPUT SELECT Button E, D Buttons VOLUME (F,G) Buttons Remote Control Sensor MENU Button Power Standby Indicator Illuminates red in standby mode, Illuminates green when the Monitor is turned on. Connection Options Connection Options
- Connection panels shown may be somewhat different from your monitor. Back Connection Panel Back Connection Panel
( ) R
( ) L
( ) R AUDIO L Y PB PR R AUDIO L
(MONO) EXTERNAL SPEAKER RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT REMOTE CONTROL AUDIO INPUT COMPONENT INPUT ALARM S-VIDEO VIDEO INPUT AUDIO INPUT AC INPUT 1 2 3 4 5 6 7 8 9 1. EXTERNAL SPEAKER (8 ohm output) Connect to optional external speaker(s).
* For further information, refer to Speaker & Speaker Stand manual. 2. RS-232C INPUT (CONTROL/SERVICE) PORT Connect to the RS-232C port on a PC. 3. DVI (Digital Visual Interface) INPUT/
RGB INPUT/AUDIO INPUT JACKS Connect the monitor output connector from a PC to the appropriate input port. 4. RGB OUTPUT PORT You can watch the RGB signal on another monitor, connect RGB OUTPUT to another monitors PC input port. 5. REMOTE CONTROL Connect your wired remote control to the remote control port on the Monitor. 6. COMPONENT INPUT/AUDIO INPUT JACKS Connect a component video/audio device to these jacks. 7. ALARM JACK Connect your alarm sensor to this jack. Detailed installation instruction is included in the alarm sensor owners manual. 8. S-VIDEO INPUTS Connect S-Video out from an S-VIDEO VCR to the S-VIDEO input. AUDIO/VIDEO INPUT JACKS Connect audio/video out from external equipment to these jacks. 9. POWER CORD SOCKET This Monitor operates on an AC power. The voltage is indi-
cated on the Specifications page. Never attempt to operate the Monitor on DC power. Owners Manual 7 Introduction Remote Control Key Functions Remote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the monitor.
- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary. POWER Switches the Monitor between ON and STANDBY. SECURITY Turn on the security PIP. APC Adjusts the factory preset picture according to the room.
(Refer to p.16) ARC Changes the picture format.
(Refer to p.22) PIP Switches the sub picture on or off.
(Refer to p.25) SWAP Exchanges main and sub picture images. (Refer to p.25, 26) MENU Displays on screen menus one by one. Exits the current menu. NUMBER buttons WIN. SIZE Adjusts the sub picture size. WIN.POSITION Moves the sub picture. SPLIT ZOOM Enlarges the picture. ZOOM-/ZOOM+
Enlarges or reduces the main picture size. Installing Batteries Installing Batteries 8 Plasma Monitor POWER SECURITY INPUT SELECT APC ARC PIP DASP PIP ARC TWIN PICTURE SWAP SUB INPUT MENU MUTE VOL OK VOL 1 4 7 2 5 8 0 3 6 9 POWER STOP P/STILL REW PLAY FF REC WIN.SIZE WIN.POSITION SPLIT ZOOM ZOOM -
ZOOM +
SLEEP INPUT SELECT Selects source: Video, S-Video, RGB, DVI, or Component mode. DASP To select the sound appropriate to your viewing program character:
Flat, Music, Cinema, Sports, or User (Refer to p.17) PIP ARC Changes the PIP picture format.
(Refer to p.25) TWIN PICTURE
(Refer to p.26) SUB INPUT Selects the input source for the sub picture. MUTE Switches the sound on or off. OK D / E Selects menu option. Memorizes menu changes. F / G (Volume button) Increases/decreases sound level. Adjusts menu settings. VCR BUTTONS Control some video cassette recorders. SLEEP Sets the Sleep Timer.
(Refer to p.18) Open the battery compartment cover on the back side and insert the batteries with correct polarity. Install two 1.5V batteries of AAA type. Dont mix used batteries with new batteries. Installation Installation Installation Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. 1.5V 1 . 5 V POWER SECURITY INPUT SELECT APC ARC PIP DASP PIP ARC TWIN PICTURE SWAP SUB INPUT MENU MUTE VOL OK VOL 1 4 7 2 5 8 0 3 6 9 POWER STOP P/STILL REW PLAY FF REC WIN.SIZE WIN.POSITION SPLIT ZOOM ZOOM -
ZOOM +
SLEEP Owners Manual Batteries BNC-RCA Adapter Remote Control D-sub 15 pin Cable Power Cord DVI-D Cable Installation Instructions Installation Instructions The Monitor can be installed in various ways such as on a wall, or on a desktop etc. The plasma display is designed to be mounted horizontally or vertically. The speakers shown are optional. GROUNDING Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker WWall Mount: Horizontal installation all Mount: Horizontal installation For proper ventilation, allow a clearance of 4 on each side and 2 from the wall. Detailed installation instruc-
tions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide. 4 inches 2 inches 4 inches 4 inches 4 inches Owners Manual 9 Installation Installation Instructions continued Installation Instructions continued Desktop Pedestal Installation Desktop Pedestal Installation For proper ventilation, allow a clearance of 4 on each side and the top, 2.36 on the bottom, and 2 from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer. 4 inches 2 inches 4 inches 4 inches 2.36 inches Detailed installation instructions are included in the optional Vertical Wall Mounting Bracket Installation and Setup Guide available from your dealer. NOTE: When installing the monitor vertically, the front panel controls must be in the left side position. When installing the monitor vertically, you have to change the OSD display mode so that the menus will appear correctly and also to protect the monitor from overheating
(Refer to P. 21). WWall Mount: V all Mount: Vertical installation ertical installation 10 Plasma Monitor External Equipment Connections External Equipment Connections NOTE: Not all cables shown are included with the plasma display. Installation VCR Setup VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor
- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen. How to connect 1. Connect the provided BNC-RCA adapter to the monitors VIDEO INPUT. 2. Connect the audio and video cables from the VCR's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to VCR, match the jack colors (Video
= yellow, Audio Left = white, and Audio Right = red). Mono VCR: Connect the video output cable from the VCR to the VIDEO input on the monitor. S-VIDEO VCR: Connect the S-Video output cable from the VCR to the S-VIDEO input on the monitor. (Note that S-Video offers higher quality). How to use 1. Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owners manual.) 2. Use the INPUT SELECT button on the remote control to select Video.
(If connected to S-VIDEO, select the S-Video input source.) R AUDIO L Y PB PR R AUDIO L
(MONO) AUDIO INPUT COMPONENT INPUT ALARM S-VIDEO VIDEO INPUT AUDIO INPUT VCR S-VIDEO OUT IN
(R) AUDIO (L) VIDEO Cable TV Setup TV Setup Cable
- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. The monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor.
- For further information regarding cable TV service, contact your local cable TV service provider(s). How to connect 1. Connect the provided BNC-RCA adapter to the monitors VIDEO INPUT. 2. Connect the audio and video cables from the Cable Box's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to a Cable Box, match the jack colors
(Video = yellow, Audio Left = white, and Audio Right = red). How to use 1. Use the INPUT SELECT button on the remote control to select Video. 2. Select your desired channel with the remote control for cable box. R AUDIO L Y PB PR R AUDIO L
(MONO) AUDIO INPUT COMPONENT INPUT ALARM S-VIDEO VIDEO INPUT AUDIO INPUT
(R) AUDIO (L) VIDEO TV VCR RF Cable Cable Box Owners Manual 11 Installation External A/V Source Setup A/V Source Setup External How to connect 1. Connect the provided BNC-RCA adapter to the monitors VIDEO INPUT. 2. Connect the audio and video cables from the external equipment's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). How to use 1. Use the INPUT SELECT button on the remote control to select Video. 2. Operate the corresponding external equipment. Refer to external equipment operating guide. DVD Setup DVD Setup R AUDIO L Y PB PR R AUDIO L
(MONO) AUDIO INPUT COMPONENT INPUT ALARM S-VIDEO VIDEO INPUT AUDIO INPUT Camcorder Video Game Set R AUDIO L VIDEO R AUDIO L Y PB PR R AUDIO L
(MONO) AUDIO INPUT COMPONENT INPUT ALARM S-VIDEO VIDEO INPUT AUDIO INPUT
(R) AUDIO (L) B R
(R) AUDIO (L) S-VIDEO or DVD DTV Setup DTV Setup
- To watch digitally broadcast programs, purchase and connect a digital set-top box.
- This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for DVI DTV
(480p,720p,1080i) mode. How to connect Use the monitors COMPONENT (Y, PB, PR) INPUT, RGB or DVI jack for video connections, depending on your set-top box connector. Then, make the corre-
sponding audio connections. How to use 1. Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) 2. Use INPUT SELECT on the remote control to select Component, RGB, or DVI. 12 Plasma Monitor How to connect 1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR) INPUT jacks and connect the DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the monitor and connect the DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure. How to use 1. Turn on the DVD player, insert a DVD. 2. Use the INPUT SELECT button on the remote control to select Component. (If connected to S-VIDEO, select the S-Video exter-
nal input source.) 3. Refer to the DVD player's manual for operating instructions. Component Input ports To get better picture quality, connect a DVD player to the compo-
nent input ports as shown below. Component ports of the Monitor Video output ports of DVD player Y Y Y Y Y PB PR Pb B-Y Cb PB Pr R-Y Cr PR DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT REMOTE CONTROL AUDIO INPUT COMPONENT INPUT ALARM S-VIDEO VIDEO INPUT AUDIO INPUT R AUDIO L Y PB PR R AUDIO L
(MONO) DVI-DTV OUTPUT
(R) AUDIO (L) or RGB-DTV OUTPUT
(R) AUDIO (L) or
(R) AUDIO (L) B R Digital Set-top Box PC Setup PC Setup
- This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel
(DDC) protocol.
- The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning rate for the graphic card. Installation
( ) R
( ) L
( ) EXTERNAL SPEAKER RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT REMOTE CONTROL How to connect 1. To get the best picture quality, adjust the PC graphics card to a 1024x768, 60Hz. Resolutions over UXGA cannot be displayed. 2. Use the monitors RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector. If the graphic card on the PC does not output ana-
log and digital RGB simultaneously, connect only one of either RGB INPUT or DVI INPUT to display the PC on the monitor. If the graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB or DVI; (the other mode is set to Plug and Play automatically by the monitor.) 3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required. How to use 1. Turn on the PC and the monitor. 2. Turn on the display by pressing the POWER button on the monitor's remote control. 3. Use the INPUT SELECT button on the remote control to select RGB or DVI. 4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. NOTES: Depending on the graphics card, DOS mode may not work if you use a DVI-I cable. Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible. The synchronization input form for Horizontal and Vertical frequencies is separate. Owners Manual 13 Installation Monitor Display Specifications (RGB-PC / DVI-PC Mode) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 720x400 640x480 800x600 832x624 848x480 31.468 37.861 31.469 37.927 31.469 35.000 37.861 37.500 43.269 35.156 37.879 46.875 53.674 49.725 31.500 35.000 37.500 70.09 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 56.25 60.31 75.00 85.06 74.55 60.00 70.00 75.00 852x480 1024x768 1152x864 1280x960 1280x1024 1360x768 1366x768 31.500 35.000 37.500 48.363 56.476 60.023 54.348 63.995 67.500 60.000 63.981 47.700 59.625 47.700 59.625 60.00 70.00 75.00 60.00 70.06 75.02 60.05 70.01 75.00 60.00 60.02 60.00 75.02 60.00 75.02 14 Plasma Monitor Operation Operation Operation TTurning on the Monitor urning on the Monitor Turning on the Monitor just after installation 1. Connect power cord correctly. 2. Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control and then the Monitor will switch on. Turning on the Monitor (power cord is still connected) 1. If the Monitor was turned off with the Press the ON/OFF button on the Monitor to turn the Monitor on. ON/OFF button on the Monitor 2. If the Monitor was turned off with the remote control and then the ON/OFF button on the Monitor Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control to turn the Monitor on. Menu Language Selection Menu Language Selection
- The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use D / E button to select the SPECIAL menu. 2. Press the G button and then use D / E button to select Language. 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice. 4. Press the OK button to save. English Espaol Portugus Franais VIDEO AUDIO TIME SPECIAL SCREEN TWIN Language G Key lock ISM Method Low power Set ID Security OSD Rotate MENU Prev. Owners Manual 15 Operation VVideo Menu Options ideo Menu Options
- Video menu adjustment are unique to each input source. Readjust Video menu settings for each following input source as preferred. RGB (PC) / DVI (PC), RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i) Video / S-Video / Component (480i) APC (Auto Picture Control) APC (Auto Picture Control)
- APC adjusts the Monitor for the best picture appearance.
- When adjusting Video menu options (contrast, brightness, color, sharpness, and tint) manually, APC automatically changes to User. 1. Press the APC button repeatedly to select the picture appearance setup option as shown below. Clear Optimum Soft User You can also adjust APC in the VIDEO menu. Clear, Optimum, and Soft settings are preset for optimum picture quality at the factory and cannot be changed. Manual Picture Control (User option) option) Manual Picture Control (
- You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select the desired picture option
(Contrast, Brightness, Color, Sharpness, or Tint). 3. Press the G button and then use F / G button to make appropriate adjustments. 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN TWIN APC ACC Color temp. Contrast 85 G Brightness Color Sharpness Tint 60 50 50 0 MENU Prev. Auto Color TTemperature Control emperature Control Auto Color
- To initialize values (reset to default settings), select the Normal option.
- When adjusting color temperature options (red, green, and blue) manually, ACC automatically changes to User. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select ACC . 3. Press the G button and then use D / E button to select either Normal (Default), Cool
(Preset), Warm (Preset), or User (Manual Adjustment). 4. Press the OK button to save. Manual Color TTemperature Control (
Manual Color emperature Control (User option) option)
- You can adjust red, green, and blue to any color temperature you prefer. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select the Color temp . 3. Press the G button and then use D / E button to select Red, Green, or Blue. 4. Use the F / G button to make appropriate adjustments. The adjustment range for Red, Green, and Blue is -20 ~ +20. 5. Press the OK button to save. VIDEO APC AUDIO TIME SPECIAL SCREEN TWIN VIDEO AUDIO TIME SPECIAL SCREEN TWIN Normal Cool Warm User ACC G Color temp. Contrast Brightness Color Sharpness Tint 85 60 50 50 0 MENU Prev. APC ACC Color temp. G Red Contrast Brightness Color Sharpness Tint 85 60 50 50 0 Green Blue 0 0 0 MENU Prev. 16 Plasma Monitor Audio Menu Options Audio Menu Options Operation DASP (Digital DASP
(Digital Auto Sound Processing) Auto Sound Processing)
- DASP lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate sound options based on the program content.
- When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to User. 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below. Flat Music Cinema Sports User You can also adjust DASP in the AUDIO menu. Flat, Music, Cinema and Sports are preset for good sound quality at the factory and cannot be changed. Manual Sound Control (User option) option) Manual Sound Control (
1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select the desired sound option
(Balance, Treble, or Bass). 3. Press the G button and then use F / G button to make appropriate adjustments. 4. Press the OK button to save. AAVLVL (Auto V
(Auto Volume Leveler) olume Leveler)
- This feature maintains an equal volume level; even if you change channels. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select AVL. 3. Press the G button and then use D / E button to select On or Off. 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN TWIN DASP AVL Balance Treble Bass 0 50 G 50 MENU Prev. VIDEO AUDIO TIME SPECIAL SCREEN TWIN DASP AVL Balance Treble Bass On Off G 0 50 50 MENU Prev. Owners Manual 17 Operation TTime Menu Options ime Menu Options Clock Setup Clock Setup
If current time setting is wrong, reset the clock. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Clock. 3. Press the G button and then use D / E button to set the hour. 4. Press the G button and then use D / E button to set the minutes. 5. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Clock G
Off timer On timer Auto off Security set Security active MENU Prev. On/Off f TTimer Setup imer Setup On/Of
- Timer function operates only if current time has been already set.
- Off-Timer function overrides On-Timer function if they are set to the same time. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Off timer or On timer. 3. Press the G button and then use D / E button to select On. To cancel On/Off timer function, select Off. 4. Press the G button and then use D / E button to set the hour. 5. Press the G button and then use D / E button to set the minutes. 6. For only On timer function; Press the G button and then use D / E button to set volume level. 7. Press the OK button to save. Auto Offf Auto Of
If there is no input signal, the Monitor turns off automatically after 10 minutes. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Auto off. 3. Press the G button and then use D / E button to select On or Off. 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Clock Off timer On timer G Auto off Security set Security active MENU Prev. On Off 12 00
Vol. 30 VIDEO AUDIO TIME SPECIAL SCREEN TWIN Clock Off timer On timer Auto off G Security set Security active MENU Prev. On Off Sleep TTimer imer Sleep
- The sleep timer turns the Monitor off at a preset time. Note that this setting is cleared when the monitor is turned off. 1. Press the SLEEP button repeatedly to select the number of minutes. First the --- Min option appears on the zz screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes. 2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to count down from the number of minutes selected. 3. To check the remaining minutes before the monitor turns off, press the SLEEP or OK button once. 4. To cancel the Sleep Timer, press the SLEEP button repeatedly until zz
--- Min appears. 18 Plasma Monitor Operation VIDEO AUDIO TIME Clock Off timer On timer Auto off Security set G SPECIAL Security active SCREEN TWIN MENU Prev. Always Time set From 23 : 00 To 07 : 30 Security PIP TTime Setup ime Setup Security PIP
- This is the function to set the time for security PIP operation. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Security set. 3. Press the G button and then use D / E button to select Always or Time set. Select Always, if you want to operate the security PIP at all times. Select Time set, if you want to set the desired time for security PIP operation. 4. When selecting Time set a. Press the G button and then use D / E button to set the desired beginning hour. b. Press the G button and then use D / E button to set the desired beginning minutes. c. Press the G button and then use D / E button to set the desired end hour. d. Press the G button and then use D / E button to set the desired end minutes. 5. Press the OK button to save. Security Active Active Security
- Set the time to keep on operating when turning the security PIP on. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Security active. 3. Press the G button and then use D / E button to set the desired setting time. The setting time range is 5 ~ 60 seconds. 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Clock Off timer On timer Auto off Security set Security active G 10 Sec. MENU Prev. Owners Manual 19 Operation Special Menu Options Special Menu Options Key Lock Key Lock
- The monitor can be set up so that it can only be used with the remote control.
- This feature can be used to prevent unauthorized viewing by disabling the front panel controls.
- This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. 1. Press the MENU button and then use D / E button to select the SPECIAL menu. 2. Press the G button and then use D / E button to select Key lock. 3. Press the G button and then use D / E button to select On or Off. When you select On, the display Key lock appears on the screen if any button on the front panel is pressed. 4. Press the OK button to save. G On Off VIDEO AUDIO TIME SPECIAL SCREEN TWIN Language Key lock ISM Method Low power Set ID Security OSD Rotate MENU Prev.
-In setting Key lock On, if the monitor is turned off with the remote control, press the INPUT SELECT button on the monitor or POWER, INPUT SELECT on the remote control to turn the monitor on. ISM (Image Sticking Minimization) Method ISM (Image Sticking Minimization) Method
- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time. 1. Press the MENU button and then use D / E button to select the SPECIAL menu. 2. Press the G button and then use D / E button to select ISM Method. 3. Press the G button and then use D / E button to select either Normal, White wash, VIDEO AUDIO TIME SPECIAL Language Key lock ISM Method G Low power Set ID Security OSD Rotate Normal White wash Orbiter Inversion Orbiter, or Inversion. Normal If image sticking is never a problem, ISM is not necessary - set to Normal. White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button. Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move every 1 minutes: Right Right Downside Downside Left Left Upside Upside. Inversion Inversion will automatically invert the plasma display panel color every 30 minutes. MENU Prev. SCREEN TWIN 4. Press the OK button to save. Low Power Low Power
- Low power reduces the plasma display's power consumption. 1. Press the MENU button and then use D / E button to select the SPECIAL menu. 2. Press the G button and then use D / E button to select Low power. 3. Press the G button and then use D / E button to select On or Off. When you select On, the screen darkens. 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Language Key lock ISM Method Low power G Set ID Security OSD Rotate On Off MENU Prev. 20 Plasma Monitor Operation Security PIP Operation Operation Security PIP 1. Press the MENU button and then use the D / E button to select the SPECIAL menu. 2. Press the G button and then use the D / E button to select Security. 3. Press the G button and then use the D / E button to select On, Standby or Off. On: The security PIP operates when turning the monitor on. Standby: The monitor switches on from standby mode, then the security PIP operates. Off: The security PIP doesnt work. 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL Language Key lock ISM Method Low power Set ID Security G SCREEN OSD Rotate TWIN MENU Prev. On Standby Off Menu Rotation for Vertical V Menu Rotation for V ertical Viewing iewing 1. Press the MENU button and then use the D / E button to select the SPECIAL menu. 2. Press the G button and then use the D / E button to select OSD Rotate. 3. Press the G button and then use the D / E button to select Normal or Rotate. Select Normal, if the monitor was installed horizontally. Select Rotate, if the monitor was installed vertically. 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Language Key lock ISM Method Low power Set ID Security OSD Rotate G MENU Prev. Normal Rotate Owners Manual 21 Operation Screen Menu Options Screen Menu Options Auto Adjustment Adjustment Auto
- RGB (PC) mode only; This function doesnt work for RGB-DTV.
- Automatically adjusts picture position and minimizes image shaking.
- After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.
- The Auto config. and Manual config. are not active in DVI mode. 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select Auto config.. 3. Press the G button to run Auto configure. When Auto config. has finished, OK will be shown on screen. If the position of the image is still not correct, try Auto adjustment again. 4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto config., you can make further adjustments with the Manual config. option. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Auto config. G To set ARC Zoom in/out Position Manual config. Screen adj. Reset XGA Mode MENU Prev. Setting Picture Format Setting Picture Format
- Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible.
- Set every aspect ratio for RGB 480p, DVI 480p, Component 480i/480p, Video, and S-Video sources.
- Use 4:3, or 16:9 for other input sources. 1. Press the ARC button repeatedly to select the desired picture format. You can also adjust ARC in the SCREEN menu. 4:3
- Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. 16:9
- Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. Horizon
- Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view. Zoom
- Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. Picture Size Zoom Picture Size Zoom
- When enlarging or reducing the picture, the image may become distorted. 1. Use ZOOM+/ZOOM- button to enlarge or reduce the picture size. Zoom adjustment range is 100~300. 2. Adjust the main picture position using the D / E / F / G buttons while in enlarged picture mode. Zoom out 100%
F D E G 22 Plasma Monitor Operation Split Zoom Split Zoom
- Enlarges the picture in correct proportions.
- Split Zoom can be used for all input sources.
In 2-Split Zoom mode, you can only move the image up or down. If a screen is enlarged, a screen can move without selecting section of screen Split Zoom. Its not available to use this function if OSD Rotate is set to the Rotate option. 1. Press the SPLIT ZOOM button repeatedly to select either 2, 4 , or 9 Split Zoom. 2-Split zoom 1 4 4-Split zoom 1 4 2 5 9-Split zoom 1 4 7 2 5 8 3 6 9 2. Press the number button corresponding to the section you wish to enlarge. You can move within the enlarged image with the D / E / F / G button. To return to normal viewing, press the SPLIT ZOOM button again. 9-Split zoom 1 4 7 2 5 8 3 6 9 Example of choosing 5. Section 5 is enlarged to fill the screen. Screen Position Screen Position
- This function works in the following mode:
RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i). 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select Position. 3. Press the G button and then use D / E / F / G button to adjust the position. 4. Press the OK button to save. Manual Configure (RGB-PC mode only) Manual Configure (RGB-PC mode only) VIDEO AUDIO TIME SPECIAL SCREEN TWIN Auto config. ARC Zoom in/out Position G Manual config. Screen adj. Reset XGA Mode MENU Prev.
If the image still isnt clear after auto adjustment and especially if characters are still jittery, adjust the picture Phase manually.
- To correct the screen size, adjust Clock. 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select Manual config.. 3. Press the G button and then use D / E button to to select Phase or Clock. 4. Use the F / G button to make appropriate adjustments. The Phase adjustment range is 0 ~ 31. The Clock adjustment range is -50 ~ +50. 5. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Auto config. ARC Zoom in/out Position Manual config. G Phase Clock Screen adj. Reset XGA Mode MENU Prev. 0 0 Owners Manual 23 Operation Screen Menu Options continued Screen Menu Options continued Screen Adjustments (V Screen Adjustments (Video, S-V ideo, S-Video and Component 480i mode only) ideo and Component 480i mode only)
- Use this function to correct jittering or picture instability while viewing a video tape. 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select Screen adj.. 3. Press the G button and then use D / E button to to select TV or VCR. Select the VCR option if watching a VCR. Select the TV option for other equipment.(Except VCR) 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL SCREEN Auto config. ARC Zoom in/out Position Manual config. Screen adj. G Reset YNR TWIN MENU Prev. TV VCR Initializing (Reset to original factory value) Initializing (Reset to original factory value)
- This function operates in every mode.
- To initialize the adjusted value 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select Reset. 3. Press the G button. You can initialize Zoom In/Out, Manual config., Position, Split zoom, PIP size, PIP posi-
tion and sub picture size for twin picture. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Auto config. ARC Zoom in/out Position Manual config. Screen adj. Reset G To set XGA Mode MENU Prev. Selecting Wide VGA/XGA Selecting W ide VGA/XGA mode (RGB-PC, DVI-PC mode only) mode (RGB-PC, DVI-PC mode only)
- To see a normal picture, match the resolution of RGB XGA mode (1024x768, 1360x768, 1366x768) with the selection for XGA mode and the resolution of RGB VGA mode (640x480, 848x480, 852x480) with the selection for VGA mode in the SCREEN menu. If the input source is RGB VGA mode, the screen menu option is changed from XGA mode to VGA mode automatically.
1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select VGA mode/XGA mode. 3. Press the G button and then use D / E button to select the desired VGA/XGA resolution. 4. Press the OK button to save. Luminance Noise Reduction (Video, S-V Luminance Noise Reduction (V ideo, S-Video and Component 480i modes only) ideo and Component 480i modes only)
- Use YNR to reduce the picture noise which may appear on the screen. 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select YNR. 3. Press the G button and then use D / E button to select On or Off. 4. Press the OK button to save. 24 Plasma Monitor VIDEO AUDIO TIME SPECIAL SCREEN TWIN Auto config. ARC Zoom in/out Position Manual config. Screen adj. Reset XGA Mode G MENU Prev. 1024x768 1360x768 1366x768 VIDEO AUDIO TIME SPECIAL SCREEN TWIN Auto config. ARC Zoom in/out Position Manual config. Screen adj. Reset YNR G MENU Prev. On Off PIPPIP (Picture-In-Picture) Feature
(Picture-In-Picture) Feature
- PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. Operation WWatching PIP atching PIP PIPPIP SizeSize Press the PIP button repeatedly to turn PIP on or off. Press the WIN.SIZE button and then use F / G button to change the sub picture size. Component Video 10 : 30 Win.size F G PIPPIP Aspect Ratio Aspect Ratio Swapping the PIP Swapping the PIP Press the PIP ARC button. The sub picture appears as shown. Press the SWAP button to switch the main and sub pictures. Component Video 10 : 30 Video Component 10 : 30 4 : 3 16 : 9 Main Picture Sub Picture Moving the PIP Moving the PIP Press the WIN.POSITION button. Press the D / E / F / G button repeatedly until desired position is achieved. The sub picture moves up/down/left/right. Win.position Selecting an Input Signal Source for the PIP Selecting an Input Signal Source for the PIP Use the SUB INPUT button to select the input source for the sub picture. Main Picture Source Available Sub Picture Sources Video S-Video Component 480i Component 480p/720p/1080i RGB and DVI S-Video, Component 480i/480p/720p/1080i, RGB, and DVI Video, Component 480i/480p/720p/1080i, RGB, and DVI Video,S-Video, RGB, and DVI Video and S-Video Component 480i, Video, and S-Video Owners Manual 25 Operation TTwin Picture Setup Option win Picture Setup Option
- As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time. Each source is given half the screen. WWatching atching TTwin Picture win Picture Press the TWIN PICTURE button repeatedly to select one of the Twin Picture options. DW 1 DW 2 Sub Picture Size Adjustment Adjustment Sub Picture Size Press the WIN.SIZE button and then use F / G button to change the sub picture size. Using the WIN.SIZE function in Twin Picture mode, main and sub picture sizes are changed simultaneously. Using the WIN.SIZE function in PIP mode, sub picture size is changed. WIN.POSITION is not functional in Twin Picture mode. Win.size F G Swapping the TTwin Picture win Picture Swapping the Use the SWAP button to switch the main and sub pictures in twin picture mode. Component Video 10 : 30 Video Component 10 : 30 Main Picture Sub Picture Selecting a Source for the TTwin Picture win Picture Selecting a Source for the Use the SUB INPUT button to select the input source for the sub picture. Main Picture Source Available Sub Picture Sources Video S-Video Component 480i Component 480p/720p/1080i RGB and DVI S-Video, Component 480i/480p/720p/1080i, RGB, and DVI Video, Component 480i/480p/720p/1080i, RGB, and DVI Video,S-Video, RGB, and DVI Video and S-Video Component 480i, Video, and S-Video 26 Plasma Monitor External Control Device Setup External Control Device Setup External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitors functions externally.
- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
- RS-232C connection cables are not supplied with the Monitor.
( ) R
( ) L
( ) R AUDIO L Y PB PR R AUDIO L
(MONO) EXTERNAL SPEAKER RS-232C INPUT
(CONTROL/SERVICE) DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT REMOTE CONTROL AUDIO INPUT COMPONENT INPUT ALARM S-VIDEO VIDEO INPUT AUDIO INPUT AC INPUT TType of Connector: D-Sub 9-pin Male ype of Connector: D-Sub 9-pin Male No. Pin Name 1 2 3 4 5 6 7 8 9 No Connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations RS-232C Configurations 1 5 9 6 7-Wire Configuration
(Standard RS-232C cable) 3- Wire Configuration
(Not standard) PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS PDP 3 2 5 6 4 8 7 TXD RXD GND DSR DTR CTS RTS PC 2 3 5 4 6 7 8 RXD TXD GND DTR DSR RTS CTS PDP 3 2 5 4 6 7 8 TXD RXD GND DTR DSR RTS CTS D-Sub 9 D-Sub 9 D-Sub 9 D-Sub 9 Owners Manual 27 External Control Device Setup Set ID Set ID
- Use this function to specify a monitor ID number.
- Refer to Real Data Mapping 1. See page 29. 1. Press the MENU button and then use the D / E button to select the SPECIAL menu. 2. Press the G button and then use D / E button to select Set ID. 3. Press the G button and then use F / G button to adjust Set ID to choose the desired monitor ID number. The adjustment range of Set ID is 1 ~ 99. VIDEO AUDIO TIME SPECIAL SCREEN TWIN Language Key lock ISM Method Low power Set ID G 1 Security OSD Rotate MENU Prev. Communication Parameters Communication Parameters Baud rate : 115200 bps (UART) Data length : 8 bits Parity : None Command Reference List Command Reference List Stop bit : 1 bit Communication code : ASCII code TTransmission / Receiving Protocol ransmission / Receiving Protocol COMMAND 1 COMMAND 2 DATA
(Hexadecimal) Transmission 01. Power k 02. Input Select k 03. Aspect Ratio k 04. Screen Mute k 05. Volume Mute k 06. Volume Control k 07. Contrast k 08. Brightness k 09. Color k 10. Tint k 11. Sharpness k 12. OSD Select k 13. Remote Control Lock Mode k k 14. PIP/Twin k 15. PIP Aspect Ratio 16. Split Zoom k k 17. PIP Position k 18. Treble k 19. Bass k 20. Balance 21. Color Temperature k k 22. Red Adjustment k 23. Green Adjustment k 24. Blue Adjustment 25. PIP Input Source k k 26. Abnormal State j 27. ISM Method j 28. Low Power j 29. Orbiter Time Setting 30. Orbiter Pixel Setting j j 31. Picture Size Setting for Twin Picture mode a b c d e f g h i j k l m n o p q r s t u v w
y z p q r s t 0 ~ 1 0 ~ 4 0 ~ 3 0 ~ 1 0 ~ 1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 1 0 ~ 1 0 ~ 3 0 ~ 1 21 ~99 0 ~ 3 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 3 0 ~ C8 0 ~ C8 0 ~ C8 0 ~ 4 0 ~ a 0 ~ 3 0 ~ 1 1 ~ FE 0 ~9 0 ~64 32. Auto Configure Menu doesnt display on screen when setting the 4, u 1 j 12, 13, and 26 ~ 32. 28 Plasma Monitor
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: k, j
* [Command 2]: To control PDP set.
* [Set ID]: You can adjust the set ID to choose desired moni-
tor ID number in Special menu. Adjustment range is 1 ~ 99. When selecting Set ID 0, every con-
nected PDP set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data. Transmit FF data to read status of command.
* [Cr]: Carriage Return ASCII code 0x0D
* [ ]: ASCII code space (0x20) OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement
[Command2][ ][Set ID][ ][NG][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data 1: Illegal Code 2: Not supported function 3: Wait more time 01. Power (Command2:a) G To control Power On/Off of the Monitor. Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off. Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Data 0 : Power Off Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
1 : Power On 1 : Power On
* In a like manner, if other functions transmit FF data based on this format, Acknowledgement data feedback presents status about each function. 02. Input Select (Command2:b) (Main Picture Input) G To select input source for the Monitor. You can also select an input source using the INPUT SELECT button on the Monitor's remote control. Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 0 : RGB 1 : Component 2 : Video Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
3 : S-video 4 : DVI 03. Aspect Ratio (Command2:c) (Main picture format) G To adjust the screen format. You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the Special menu. Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 0 : Wide screen (16:9) 1 : Normal screen (4:3) 2 : Full screen (Zoom) 3 : Horizon Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
* You select either 16:9 or 4:3 screen aspect ratio using the PC, DTV 720p/1080i. External Control Device Setup 04. Screen Mute (Command2:d) G To select screen mute on/off. Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
05. Volume Mute (Command2:e) G To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute on (Volume off) 1 : Volume mute off (Volume on) Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
06. Volume Control (Command2:f) G To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64 Refer to Real data mapping1 as shown below. Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
07. Contrast (Command2:g) G To adjust screen contrast. You can also adjust contrast in the Video menu. Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64 Refer to Real data mapping1 as shown below. Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
* Real data mapping 1 0 : Step 0 A : Step 10 (SET ID 10) F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) 64 : Step 100 Owners Manual 29 External Control Device Setup 08. Brightness (Command2:h) G To adjust screen brightness. You can also adjust brightness in the Video menu. Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64 Refer to Real data mapping 1. See page 29. Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
09. Color (Command2:i) G To adjust the screen color. You can also adjust color in the Video menu. Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64 Refer to Real data mapping 1. See page 29. Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
10. Tint (Command2:j) G To adjust the screen tint. You can also adjust tint in the Video menu. Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0 ~ Green : 64 Refer to Real data mapping 1. See page 29. Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
11. Sharpness (Command2:k) G To adjust the screen sharpness. You can also adjust sharpness in the Video menu. Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Refer to Real data mapping 1. See page 29. Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
12. OSD Select (Command2:l) G To select OSD (On Screen Display) on/off. Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD off 1: OSD on Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
30 Plasma Monitor 13. Remote Control Lock Mode (Command2:m) G To lock the remote control and front panel controls on the monitor Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0: Lock off Acknowledgement 1: Lock on
[m][ ][Set ID][ ][OK][Data][x]
If youre not using the remote control and front panel con-
trols on the monitor, use this mode. When main power is on/off, remote control lock is released. 14. PIP / Twin (Command2:n) G To control the PIP (Picture-in-Picture) or Twin Picture. You can also control the PIP/Twin picture mode using the PIP or TWIN PICTURE button on the remote control or in the Twin menu. Transmission
[k][n][ ][Set ID][ ][Data][Cr]
Data 0: PIP/DW off 1: PIP Acknowledgement
[n][ ][Set ID][ ][OK][Data][x]
2: DW1 3: DW2 15. PIP Aspect Ratio (Command2:o) G To select the PIP picture format. You can also select the PIP picture format using PIP ARC on the remote control. Transmission
[k][o][ ][Set ID][ ][Data][Cr]
Data 0: 4:3 Acknowledgement
[o][ ][Set ID][ ][OK][Data][x]
1: 16:9 16. Split Zoom (Command2:p) G To operate split zoom function and select the split zoom section number. Transmission
[k][p][ ][Set ID][ ][Data][Cr]
Data Min: 21 ~ Max: 99 Refer to Real data mapping 2. Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
* Real data mapping 2 21: Selection 1 of 2 split zoom 24: Selection 4 of 2 split zoom 41: Selection 1 of 4 split zoom 42: Selection 2 of 4 split zoom 44: Selection 4 of 4 split zoom 45: Selection 5 of 4 split zoom 91: Selection 1 of 9 split zoom 99: Selection 9 of 9 split zoom 17. PIP Position (Command2:q) G To select sub picture position for PIP. You can also adjust the sub picture position using Win.position on the remote control or in the Twin menu. Transmission
[k][q][ ][Set ID][ ][Data][Cr]
Data 0: Right down on screen 1: Left down on screen 2: Left up on screen 3: Right up on screen Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
18. Treble (Command2:r) G To adjust treble. You can also adjust treble in the Audio menu. Transmission
[k][r][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Refer to Real data mapping 1. See page 29. Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
19. Bass (Command2:s) G To adjust bass. You can also adjust bass in the Audio menu. Transmission
[k][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Refer to Real data mapping 1. See page 29. Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
20. Balance (Command2:t) G To adjust balance. You can also adjust balance in the Audio menu. Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Refer to Real data mapping 1. See page 29. Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
External Control Device Setup 21. Color Temperature (Command2:u) G To adjust color temperature. You can also adjust ACC in the Video menu. Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0: Normal 1: Cool 2: Warm 3: User Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
22. Red Adjustment (Command2:v) G To adjust red in color temperature. Transmission
[k][v][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: C8 Refer to Real data mapping 3 as shown below. Acknowledgement
[v][ ][Set ID][ ][OK][Data][x]
23. Green Adjustment (Command2:w) G To adjust green in color temperature. Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: C8 Refer to Real data mapping 3 as shown below. Acknowledgement
[w][ ][Set ID][ ][OK][Data][x]
24. Blue Adjustment (Command2:$) G To adjust blue in color temperature. Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: C8 Refer to Real data mapping 3 as shown below. Acknowledgement
[$][ ][Set ID][ ][OK][Data][x]
* Real data mapping 3 0 : -20 5 : -19 A : -18 5F: -1 64: 0 69: +1 C3: +19 C8: +20 Owners Manual 31 External Control Device Setup 25. PIP Input Select (Command2:y) 29. Orbiter Time Setting (Command2:r) G To select input source for sub picture in PIP mode. Transmission
[k][y][ ][Set ID][ ][Data][Cr]
Data 0: RGB 2: Video 1: Component 3: S-video 4: DVI Acknowledgement
[y][ ][Set ID][ ][OK][Data][x]
G To adjust orbiter operation time term. Transmission
[j][r][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: FE Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
30. Orbiter Pixel Setting (Command2:s) G To adjust pixel number in orbiter function. Transmission
[j][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 9 Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
31. Picture Size Setting for Twin Picture mode
(Command2:t) G To adjust main picture size in twin picture mode. Transmission
[j][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64 Refer to Real data mapping1. See page 29. Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
32. Auto Configure (Command2:u) G To adjust picture position and minimize image shaking automatically. Auto Configure only works in RGB-PC mode. Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 1: To set Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
26. Abnormal State (Command2:z) G To recognize an abnormal state. Transmission
[k][z][ ][Set ID][ ][FF][Cr]
Data FF:Read Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
Data 0: Normal (Power on and signal exist) 1: No signal (Power on) 2: Turn the monitor off by remote control 3: Turn the monitor off by sleep time function 4: Turn the monitor off by RS-232C function 5: 5V down 6: AC down 7: Turn the monitor off by Fan Alarm function 8: Turn the monitor off by off time function 9: Turn the monitor off by auto off function a: Turn the monitor off by AV board detect 27. ISM Method (Command2:p) G To avoid having a fixed image remain on screen. Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 0: Normal 2: Orbiter 3: Inversion 1: White wash Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
28. Low Power (Command2:q) G To control the low power function on/off. Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data 0: Low power off 1: Low power on Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
32 Plasma Monitor IR Code IR Code IR Code How to Connect How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code Remote Control IR Code G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz TC T1 Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 G Configuration of frame 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Repeat frame G Lead code Repeat code Tf 9 ms 4.5 ms G Repeat code 0.55 ms G Bit description Bit 0 9 ms 0.56 ms 1.12 ms 2.25 ms Bit 1 G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz 0.56 ms 2.24 ms Owners Manual 33 IR Code Code (Hexa) Function Note 00H 01H 02H 03H 08H C4H C5H 09H 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 0BH D5H C6H 5AH D8H BFH 0EH 44H 43H 52H 4DH 60H 61H 63H 64H 6BH 40H 41H 69H 6AH 7BH 79H 76H 77H AFH 99H UP (D) DOWN (E) VOL+ (G) VOL- (F) POWER On/Off POWER ON POWER OFF MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 AII INPUT SELECT RGB DVI VIDEO S-VIDEO COMPONENT SLEEP OK () MENU DASP APC PIP SUB INPUT SWAP PIP ARC TWIN PICTURE ZOOM +
ZOOM -
Window Size Window Position Split Zoom ARC ARC (4:3) ARC (16:9) ARC (ZOOM) Auto configure R/C Button R/C Button R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (RGB/DVI/Video/S-video/Component) Discrete IR Code (Input RGB Selection) Discrete IR Code (Input DVI Selection) Discrete IR Code (Input Video Selection) Discrete IR Code (Input S-video Selection) Discrete IR Code (Input Component Selection) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (PIP/TWIN Exchange) R/C Button (4:3/16:9) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button(4:3/16:9/Zoom Mode Selection) Discrete IR Code (Only 4:3 mode) Discrete IR Code (Only 16:9 mode) Discrete IR Code (Only ZOOM mode) Discrete IR Code (Only RGB-PC mode) 34 Plasma Monitor TTroubleshooting Checklist roubleshooting Checklist Troubleshooting Checklist Check whether the Monitor is turned on. Power cord inserted into wall outlet?
No picture &
No sound Test the wall power outlet, plug other products power cord into the wall outlet where the Monitors power cord was plugged in. Picture OK &
No sound Press the VOLUME (G) button. Sound muted? Press MUTE button. Check to see if there is any object between the Plasma Display and the remote control causing obstruction. The remote control doesnt work Are batteries installed with correct polarity (+ to +, - to -)?
(Refer to p.8) Install new batteries. (Refer to p.8) Picture appears slowly after switching on This is normal, the image is muted during the plasma display startup process. Please contact your service center, if the picture has not appeared after five minutes. Select Color in the VIDEO menu and press the VOLUME (G) button.
(Refer to p.16) No or Poor color or Poor picture Keep a sufficient distance between the Monitor and the VCR. Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the screen gets dark.) Horizontal/vertical bars or picture shaking Check for local interference such as an electrical appliance or power tool. No output from one of the speakers Adjust Balance in the AUDIO menu. (Refer to p.17) Unusual sound from inside the monitor A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the monitor. Owners Manual 35 Maintenance Maintenance Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen Cleaning the Screen 1. Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor. Cleaning the Cabinet Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence Absence Extended If you expect to leave your Monitor dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges. 36 Plasma Monitor Product Specifications Product Specifications Specification MODELS Width (inches / mm) Height (inches / mm) Depth (inches / mm) Weight (pounds / kg) Power requirement Resolution Color MU-50PZ90MQ 48.2 / 1223 28.9 / 734 4.1 / 105 95.2 / 43.2 AC120V, 60Hz 1366 x 768 (Dot) 16,770,000 (256 steps of each R, G and B) Operating Temperature Range Operating Humidity Range Maximum Elevation 32 ~ 104F (0 ~ 40C) Less than 80%
6561 feet (2000m) The specifications shown above may be changed without notice for quality improvement. Owners Manual 37 Notes Notes Notes 38 Plasma Monitor Notes Notes Notes Owners Manual 39 PLASMA MONITOR OWNERS MANUAL MODEL : MU-50PZ90MQ Please read this owners manual thoroughly before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and relate this information to your dealer if you ever require service. Model Number :
Serial Number :
P/NO : 3828VA0410H (RF03GB)
This product uses the FCC Data API but is not endorsed or certified by the FCC