| submitted | available | document details (if available) | source link |
|---|---|---|---|
| October 01 2019 | March 30 2020 | Intel® WiFi Adapter Information Guide Acrobat Web Capture 11.0 |
| various | User Manual | Users Manual | 1.32 MiB | October 01 2019 / March 30 2020 | delayed release |
Intel WiFi Adapter Information Guide This version of Intel PROSet/Wireless WiFi Software is compatible with the adapters listed below. However, note that newer features provided in this software release are generally not supported for older, legacy adapters. The following adapters are supported on this release for Windows* 10:
Intel Dual Band Wireless-AC 7260 Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Intel Dual Band Wireless-AC 3160 Intel Dual Band Wireless-AC 7265 Intel Dual Band Wireless-N 7265 Intel Wireless-N 7265 Intel Dual Band Wireless-AC 3165 Intel Dual Band Wireless-AC 8260 (64-bit only) Intel Dual Band Wireless-AC 8265 Intel Wireless-AC 9260 Intel Wireless-AC 9461 Intel Wireless-AC 9462 Intel Wireless-AC 9560 Intel Wireless Gigabit 11000 Intel Wireless Gigabit 11100VR Intel Wireless Gigabit Sink W13100 Intel Wireless Gigabit Sink W13110VR Intel Tri-Band Wireless-AC 18265 Intel Wi-Fi 6 AX201/ 14T90N/ 14T90N Intel Centrino Wireless-N 100 Intel Centrino Wireless-N 130 Intel Centrino Wireless-N 1000 Intel Centrino Wireless-N 1030 Intel Centrino Advanced-N 6200 Intel Centrino Advanced-N 6230 Intel Centrino Wireless-N 105 Intel Centrino Wireless-N 135 Intel Centrino Wireless-N 2200 Intel Centrino Wireless-N 2230 Intel Centrino Wireless-N + WiMAX 6150 Intel Centrino Advanced-N 6205 Intel Centrino Advanced-N 6235 Intel Centrino Advanced-N + WiMAX 6250 Intel Centrino Ultimate-N 6300 Intel Dual Band Wireless-AC 7260 Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Intel Dual Band Wireless-AC 3160 Intel Dual Band Wireless-AC 3165 Intel Dual Band Wireless-AC 3168 Intel Dual Band Wireless-AC 7265 Intel Dual Band Wireless-N 7265 Intel Wireless-N 7265 Intel Dual Band Wireless-AC 8260 The following adapters are supported on this release for Windows* 8 and Windows* 8.1 with Windows* 7 drivers from Intel:
The following adapters are supported on this release for Windows* 8 with Windows* 8 drivers from Intel:
The following adapters are supported on this release for Windows* 8.1 with Windows* 8 drivers from Intel:
The following adapters are supported on this release for Windows* 8.1 with Windows* 8.1 drivers from Intel:
Intel Centrino Wireless-N 105 Intel Centrino Wireless-N 135 Intel Centrino Wireless-N 2200 Intel Centrino Wireless-N 2230 Intel Centrino Wireless-N + WiMAX 6150 Intel Centrino Advanced-N 6205 Intel Centrino Advanced-N 6235 Intel Centrino Advanced-N + WiMAX 6250 Intel Centrino Ultimate-N 6300 Intel Dual Band Wireless-AC 7260 Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Intel Dual Band Wireless-AC 3160 Intel Dual Band Wireless-AC 3165 Intel Dual Band Wireless-AC 3168 Intel Dual Band Wireless-AC 7265 Intel Dual Band Wireless-N 7265 Intel Wireless-N 7265 Intel Dual Band Wireless-AC 8260 Intel Tri-Band Wireless-AC 17265 Intel Tri-Band Wireless-AC 18260 Intel Wireless Gigabit 11000 Adapter Settings Regulatory Information Specifications Important Information Support Warranty Glossary With your WiFi network card, you can access WiFi networks, share files or printers, or even share your Internet connection. All of these features can be explored using a WiFi network in your home or office. This WiFi network solution is designed for both home and business use. Additional users and features can be added as your networking needs grow and change. This guide contains basic information about Intel adapters. It includes information about several adapter properties that you can set to control and enhance the performance of your adapter with your particular wireless network and environment. Intel wireless adapters enable fast connectivity without wires for desktop and notebook PCs. Depending on the model of your Intel WiFi adapter, your adapter is compatible with 802.11a, 802.11b, 802.11g, and 802.11n (draft 2.0) wireless standards. Operating at 5GHz or 2.4GHz frequency at data rates of up to 450 Mbps, you can now connect your computer to existing high-speed networks that use multiple access points within large or small environments. Your WiFi adapter maintains automatic data rate control according to the access point location and signal strength to achieve the fastest possible connection. All of your wireless network connections are easily managed by the WiFi connection utility. Profiles that are set up through the WiFi connection utility provide enhanced security measures with 802.1X network authentication. Information in this document is subject to change without notice. 20042014 Intel Corporation. All rights reserved. Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 USA The copying or reproducing of any material in this document in any manner whatsoever without the written permission of Intel Corporation is strictly forbidden. Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Intel disclaims any proprietary interest in trademarks and trade names other than its own. Microsoft and Windows are registered trademarks of Microsoft Corporation. Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
*Other names and brands may be claimed as the property of others. Intel Corporation assumes no responsibility for errors or omissions in this document. Nor does Intel make any commitment to update the information contained herein. IMPORTANT NOTICE FOR ALL USERS OR DISTRIBUTORS:
Intel wireless LAN adapters are engineered, manufactured, tested, and quality checked to ensure that they meet all necessary local and governmental regulatory agency requirements for the regions that they are designated and/or marked to ship into. Because wireless LANs are generally unlicensed devices that share spectrum with radars, satellites, and other licensed and unlicensed devices, it is sometimes necessary to dynamically detect, avoid, and limit usage to avoid interference with these devices. In many instances Intel is required to provide test data to prove regional and local compliance to regional and governmental regulations before certification or approval to use the product is granted. Intel's wireless LAN's EEPROM, firmware, and software driver are designed to carefully control parameters that affect radio operation and to ensure electromagnetic compliance (EMC). These parameters include, without limitation, RF power, spectrum usage, channel scanning, and human exposure. For these reasons Intel cannot permit any manipulation by third parties of the software provided in binary format with the wireless LAN adapters (e.g., the EEPROM and firmware). Furthermore, if you use any patches, utilities, or code with the Intel wireless LAN adapters that have been manipulated by an unauthorized party (i.e., patches, utilities, or code (including open source code modifications) which have not been validated by Intel), (i) you will be solely responsible for ensuring the regulatory compliance of the products, (ii) Intel will bear no liability, under any theory of liability for any issues associated with the modified products, including without limitation, claims under the warranty and/or issues arising from regulatory non-compliance, and (iii) Intel will not provide or be required to assist in providing support to any third parties for such modified products. Note: Many regulatory agencies consider Wireless LAN adapters to be "modules", and accordingly, condition system-
level regulatory approval upon receipt and review of test data documenting that the antennas and system configuration do not cause the EMC and radio operation to be non-compliant. July 9, 2018 Back to Contents Adapter Settings How to Access The Advanced tab displays the device properties for the WiFi adapter installed on your computer. At the Intel PROSet/Wireless WiFi Connection Utility, Advanced Menu click Adapter Settings. Select the Advanced tab. WiFi Adapter Settings Description Name Description 802.11ac Mode
(5GHz) The 802.11ac standard builds on 802.11n standard. 802.11ac Mode delivers up to 867Mbps
(theoretical) by increasing channel bandwidth to 80MHz and adding higher density modulation (256 QAM). Select Enabled or Disabled to set the 802.11ac mode of the WiFi adapter. Enabled is the default setting. This setting applies to 802.11ac capable adapters only. 802.11n Channel Width
(2.4 GHz) Set high throughput channel width to maximize performance. Set the channel width to Auto or 20MHz. Use 20MHz if 802.11n channels are restricted. This setting applies to 802.11n capable adapters only. NOTE: This setting does not apply to the Intel Wireless WiFi Link 4965AGN (uses 20 MHz channel width only). 802.11n Channel Width
(5.2 GHz) Set high throughput channel width to maximize performance. Set the channel width to Auto or 20MHz. Use 20MHz if 802.11n channels are restricted. This setting applies to 802.11n capable adapters only. NOTE: This setting does not apply to the following adapters:
Intel WiFi Link 1000 Intel Wireless WiFi Link 4965AGN 802.11n Mode The 802.11n standard builds on previous 802.11 standards by adding multiple-input multiple-output (MIMO). MIMO increases data throughput to improve transfer rate. Select Enabled or Disabled to set the 802.11n mode of the WiFi adapter. Enabled is the default setting. This setting applies to 802.11n capable adapters only. Ad Hoc Channel 802.11b/g Ad Hoc QoS Mode NOTE: To achieve transfer rates greater than 54 Mbps on 802.11n connections, WPA2*-
AES security must be selected. No security (None) can be selected to enable network setup and troubleshooting. An administrator can enable or disable support for high throughput mode to reduce power-
consumption or conflicts with other bands or compatibility issues. Select Enabled or Disabled. Quality of Service (QoS) control in ad hoc networks. QoS provides prioritization of traffic from the access point over a wireless LAN based on traffic classification. WMM (Wi-Fi Multimedia) is the QoS certification of the Wi-Fi Alliance (WFA). When WMM is enabled, the WiFi adapter uses WMM to support priority tagging and queuing capabilities for Wi-Fi networks. WMM Enabled WMM Disabled (Default) Bluetooth AMP Enable or disable Bluetooth AMP. AMP stands for alternate MAC/PHY and uses the 802.11
(Wi-Fi) as the high-speed transport. If disabled, Bluetooth HS is turned off. HT Mode/VHT Mode/Disabled This settings lets you select HT Mode (High Throughput mode), VHT Mode (Very High Throughput Mode) or to disable both modes. HT Mode supports 802.11n compatibility, whereas VHT Mode supports 802.11ac compatibility. Fat Channel Intolerant This setting communicates to access points that this WiFi adapter does not prefer 40MHz channels in the 2.4GHz band. The default setting is for this to be turned off (disabled), so that the adapter does not send this notification. If the access point continues to use 40MHz channels, the WiFi adapter will also use 40MHz channels if the 802.11n Channel Width
(2.4GHz) setting is AUTO. NOTE: This setting does not apply to the following adapters:
Intel Wireless WiFi Link 4965AG_ Intel PRO/Wireless 3945ABG Network Connection Mixed mode protection Use to avoid data collisions in a mixed 802.11b and 802.11g environment. Request to Send/Clear to Send (RTS/CTS) should be used in an environment where clients may not hear each other. CTS-to-self can be used to gain more throughput in an environment where clients are in close proximity and can hear each other. Preferred Band In an environment with other radiating devices nearby (such as microwave ovens, cordless telephones, access points, or client devices), in order to reduce interference you may prefer the 5GHz band over the 2.4GHz band, or vice-versa. Your choices are:
No Preference Prefer 2.4GHz band Prefer 5GHz band Here are the various Wi-Fi bands:
802.11 legacy - 2.4GHz 802.11a - 5GHz 802.11b - 2.4GHz 802.11g - 2.4GHz 802.11n - 2.4GHz and 5GHz 802.11ac - 5GHz 802.11ad - 60GHz Roaming Aggressiveness This setting lets you define how aggressively your wireless client roams to improve connection to an access point. There are five available settings. 3. Medium: This is the default. A balanced setting between not roaming and performance. 1. Lowest: Your wireless client will not roam. Only significant link quality degradation causes it to roam to another access point. 5. Highest: Your wireless client continuously tracks the link quality. If any degradation occurs, it tries to find and roam to a better access point. Transmit Power Default Setting: Highest power setting. Lowest: Minimum Coverage: Set the adapter to the lowest transmit power. Enables you to expand the number of coverage areas or confine a coverage area. Reduces the coverage area in high traffic areas to improve overall transmission quality and avoids congestion and interference with other devices. Highest: Maximum Coverage: Set the adapter to a maximum transmit power level. Select for maximum performance and range in environments with limited additional WiFi radio devices. NOTE: The optimal setting is for a user to always set the transmit power at the lowest possible level that is still compatible with the quality of their communication. This allows the maximum number of wireless devices to operate in dense areas and reduce interference with other devices that it shares the same radio spectrum with. NOTE: This setting takes effect when either Network (Infrastructure) or Device to Device
(ad hoc) mode is used. Wake on Magic Packet This setting, enabled, wakes the computer from a sleep state when it receives a "magic packet" from a sending computer. The magic packet contains the MAC address of the intended destination computer. Enabling turns on Wake on Magic Packet. Disabling turns off Wake on Magic Packet. Disabling this only disables the magic packet feature, not Wake on Wireless LAN. Wake on Pattern Match This feature wakes the computer from a sleep state when a particular wake pattern is received at the adapter. This feature is supported by the Window* 7 and Windows 8. Such patterns typically are:
Wake on new incoming TCP connection for IPv4 and IPv6 (TCP SYN IPv4 and TCP SYN IPv6). Wake on 802.1x re-authentication packets. Wireless Mode Select which mode to use for connection to a wireless network:
Disabling this only disables the pattern match feature, not Wake on Wireless LAN. 802.11a only: Connect the wireless WiFi adapter to 802.11a networks only. Not applicable for all adapters. 802.11b only: Connect the wireless WiFi adapter to 802.11b networks only. Not applicable for all adapters. 802.11g only: Connect the wireless WiFi adapter to 802.11g networks only. 802.11a and 802.11g: Connect the WiFi adapter to 802.11a and 802.11g networks only. Not applicable for all adapters. 802.11b and 802.11g: Connect the WiFi adapter to 802.11b and 802.11g networks only. Not applicable for all adapters. 802.11a, 802.11b, and 802.11g: (Default) - Connect to either 802.11a, 802.11b or 802.11g wireless networks. Not applicable for all adapters. OK Cancel Saves settings and returns to the previous page. Closes and cancels any changes. Back to Top Back to Contents Trademarks and Disclaimers Back to Contents Regulatory Information This section provides regulatory information for the following wireless adapters:
Intel Centrino Wireless-N 100 Intel Centrino Wireless-N 105 Intel Centrino Wireless-N 130 Intel Centrino Wireless-N 135 Intel Centrino Wireless-N 1000 Intel Centrino Wireless-N 1030 Intel Centrino Wireless-N 2200 Intel Centrino Wireless-N 2230 Intel Centrino Wireless-N + WiMAX 6150 Intel Centrino Advanced-N 6200 Intel Centrino Advanced-N 6205 Intel Centrino Advanced-N 6230 Intel Centrino Advanced-N 6235 Intel Centrino Advanced-N + WiMAX 6250 Intel Centrino Ultimate-N 6300 Intel Dual Band Wireless-AC 7260 Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Intel Dual Band Wireless-AC 3160 Intel Dual Band Wireless-AC 3165 Intel Dual Band Wireless-AC 3168 Intel Dual Band Wireless-AC 7265 Intel Dual Band Wireless-N 7265 Intel Wireless-N 7265 Intel Dual Band Wireless-AC 8260 Intel Dual Band Wireless-AC 8265 Intel Wireless-AC 9260 Intel Wireless-AC 9461 Intel Wireless-AC 9462 Intel Wireless-AC 9560 Intel Tri-Band Wireless-AC 17265 Intel Tri-Band Wireless-AC 18260 Intel Tri-Band Wireless-AC 18265 Intel Wireless Gigabit Sink W13100 Intel Wireless Gigabit 11000 Intel Wireless Gigabit Sink W13110VR Intel Wireless Gigabit 11100VR Intel Wi-Fi 6 AX201/ 14T90N NOTE: Due to the evolving state of regulations and standards in the wireless LAN field (IEEE 802.11 and similar standards), the information provided herein is subject to change. Intel Corporation assumes no responsibility for errors or omissions in this document. Intel WiFi/WiMAX Wireless Adapters Information in this section supports the following wireless adapters:
Intel Centrino Wireless-N + WiMAX 6150 Intel Centrino Advanced-N + WiMAX 6250 See Specifications for complete wireless adapter specifications. NOTE: In this section, all references to the "wireless adapter" refer to all adapters listed above. The following information is provided:
Information for the User Regulatory Information Regulatory ID Information for OEMs and Host Integrators INFORMATION FOR THE USER Safety Notices USA FCC Radio Frequency Exposure The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. The wireless adapter meets the Human Exposure requirements found in FCC Part 2, 15C, 15E along with guidance from KDB 447498, KDB 248227 and KDB 616217. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCCs recommended limits. The following safety precautions should be observed:
Do not touch or move antenna while the unit is transmitting or receiving. Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting. Do not operate the radio or attempt to transmit data unless the antenna is connected; this behavior may cause damage to the radio. Use in specific environments:
The use of wireless adapters in hazardous locations is limited by the constraints posed by the safety directors of such environments. The use of electronic devices equipped with wireless adapters on airplanes is governed by rules for each commercial airline operator. The use of wireless adapters in hospitals is restricted to the limits set forth by each hospital. Explosive Device Proximity Warning Warning: Do not operate a portable transmitter (including this wireless adapter) near unshielded blasting caps or in an explosive environment unless the transmitter has been modified to be qualified for such use. Antenna Warnings Use On Aircraft Caution Warning: The wireless adapter is not designed for use with high-gain directional antennas. Caution: Regulations of commercial airline operators may prohibit airborne operation of certain electronic devices equipped with radio-frequency wireless devices (wireless adapters) because their signals could interfere with critical aircraft instruments. Caution: 60 GHz/802.11ad equipment is not permitted on aircraft per FCC 15.255. OEM and host integrators should consider this FCC rule in host devices. Other Wireless Devices Safety Notices for Other Devices in the Wireless Network: See the documentation supplied with wireless adapters or other devices in the wireless network. Local Restrictions on 802.11a, 802.11b, 802.11d, 802.11g, 802.11n, 802.11ac, and 802.16e Radio Usage Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11d, 802.11g, 802.11n, 802.11ac, and 802.16e wireless LAN devices may not yet be harmonized in all countries, 802.11a, 802.11b, 802.11d, 802.11g, 802.11n, 802.11ac, and 802.16e products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. The device transmit power control (TPC) interface is part of the Intel PROSet/Wireless WiFi Connection Utility Software. Operational restrictions for Equivalent Isotropic Radiated Power (EIRP) are provided by the system manufacturer. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such. Wireless Interoperability The wireless adapter is designed to be interoperable with other wireless LAN products that are based on direct sequence spread spectrum (DSSS) radio technology and to comply with the following standards:
IEEE Std. 802.11b compliant Standard on Wireless LAN IEEE Std. 802.11g compliant Standard on Wireless LAN IEEE Std. 802.11a compliant Standard on Wireless LAN IEEE Std. 802.11n draft 2.0 compliant on Wireless LAN IEEE 802.16e-2005 Wave 2 compliant Wireless Fidelity certification, as defined by the Wi-Fi Alliance WiMAX certification as defined by the WiMAX Forum The Wireless Adapter and Your Health The wireless adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by the wireless adapter, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The wireless adapter operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of the wireless adapter may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations may include:
Using the wireless adapter on board airplanes, or Using the wireless adapter in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If you are uncertain of the policy that applies to the use of wireless adapters in a specific organization or environment (an airport, for example), you are encouraged to ask for authorization to use the adapter before you turn it on. REGULATORY INFORMATION USA - Federal Communications Commission (FCC) This wireless adapter is restricted to indoor use due to its operation in the 5.15 to 5.25 and 5.470 to 5.75GHz frequency ranges. No configuration controls are provided for Intel wireless adapters allowing any change in the frequency of operations outside the FCC grant of authorization for U.S. operation according to Part 15.407 of the FCC rules. Intel wireless adapters are intended for OEM integrators only. Intel wireless adapters cannot be co-located with any other transmitter unless approved by the FCC. This wireless adapter complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. Class B Device Interference Statement This wireless adapter has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This wireless adapter generates, uses, and can radiate radio frequency energy. If the wireless adapter is not installed and used in accordance with the instructions, the wireless adapter may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this wireless adapter does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:
Reorient or relocate the receiving antenna of the equipment experiencing the interference. Increase the distance between the wireless adapter and the equipment experiencing the interference. Connect the computer with the wireless adapter to an outlet on a circuit different from that to which the equipment experiencing the interference is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE: The adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Safety Approval Considerations This device has been safety approved as a component and is for use only in complete equipment where the acceptability of the combination is determined by the appropriate safety agencies. When installed, consideration must be given to the following:
It must be installed into a compliant host device meeting the requirement of UL/EN/IEC 60950-1 2nd edition including the general provisions of enclosure design 1.6.2 and specifically paragraph 1.2.6.2 (Fire Enclosure). The device shall be supplied by a SELV source when installed in the end-use equipment. A heating test shall be considered in the end-use product for meeting the requirement of UL/EN/IEC 60950-1 2nd edition. Applies only to brominated and chlorinated flame retardants (BFRs/CFRs) and PVC in the final product. Intel components as well as purchased components on the finished assembly meet JS-709 requirements, and the PCB /
substrate meet IEC 61249-2-21 requirements. The replacement of halogenated flame retardants and/or PVC may not be better for the environment. Low Halogen 5GHz Japan Korea Mexico
. 5150-5250MHz . La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Taiwan
, 5.25-5.35 Radio Approvals To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer's OEM Regulatory Guidance document. Modular Regulatory Certification Country Markings A list of countries requiring regulatory markings is available. Note that the lists include only countries requiring marking but not all certified countries. To find the regulatory country marking information for your adapter, perform these steps:
1. Open this web site: http://www.intel.com/content/www/us/en/support/network-and-i-o/wireless-
networking/000007443.html 2. Click on the link for your adapter. 3. Click on Regulatory Marking Document for your adapter. INFORMATION FOR OEMs and HOST INTEGRATORS The guidelines described within this document are provided to OEM integrators installing Intel wireless adapters in notebook and tablet PC host platforms. Adherence to these requirements is necessary to meet the conditions of compliance with FCC rules, including RF exposure. When all antenna type and placement guidelines described herein are fulfilled the Intel wireless adapters may be incorporated into notebook and tablet PC host platforms with no further restrictions. If any of the guidelines described herein are not satisfied it may be necessary for the OEM or integrator to perform additional testing and/or obtain additional approval. The OEM or integrator is responsible to determine the required host regulatory testing and/or obtaining the required host approvals for compliance. Intel wireless adapters are intended for OEMs and host integrators only. The Intel wireless adapter FCC Grant of Authorization describes any limited conditions of modular approval. The Intel wireless adapters must be operated with an access point that has been approved for the country of operation. Changes or modification to Intel wireless adapters by OEMs, integrators or other third parties is not permitted. Any changes or modification to Intel wireless adapters by OEMs, integrators or other third parties will void authorization to operate the adapter. Antenna Type and Gains Only antennas of the same type and with equal or less gains as shown below may be used with the Intel wireless adapters. Other types of antennas and/or higher gain antennas may require additional authorization for operation. Antenna Location
(Main/Aux) 2.4GHz Peak Gain in dBi*
2.6GHz Peak Gain in dBi*
5.2GHz Peak Gain in dBi*
5.5GHz Peak Gain in dBi*
5.7GHz Peak Gain in dBi*
3.24 3.47 3.73 4.77 4.77 Antenna Type PIFA Main Aux MIMO
*All antenna gains include cable loss. Antenna Placement Within the Host Platform To ensure RF exposure compliance the antenna(s) used with the Intel wireless adapters must be installed in notebook or tablet PC host platforms to provide a minimum separation distance from all persons, in all operating modes and orientations of the host platform, with strict adherence to the table below. The antenna separation distance applies to both horizontal and vertical orientation of the antenna when installed in the host system. Intel Wireless Adapter Minimum required antenna-to-user separation distance Intel Centrino Wireless-N + WiMAX 6150 Intel Centrino Wireless-N + WiMAX 6350 18 mm 17 mm Simultaneous Transmission of Intel Wireless Adapters with Other Integrated or Plug-In Transmitters Based upon FCC Knowledge Database publication number 616217 when there are multiple transmitting devices installed in a host device, an RF exposure transmitting assessment shall be performed to determine the necessary application and test requirements. OEM integrators must identify all possible combinations of simultaneous transmission configurations for all transmitters and antennas installed in the host system. This includes transmitters installed in the host as mobile devices (>20 cm separation from user) and portable devices (<20 cm separation from user). OEM integrators should consult the actual FCC KDB 616217 document for all details in making this assessment to determine if any additional requirements for testing or FCC approval is necessary. Information To Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating the Intel wireless adapter, in compliance with local regulations. Host system must be labeled with "Contains FCC ID: XXXXXXXX", FCC ID displayed on label. The Intel wireless adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Intel Corporation is not responsible for any radio or television interference caused by unauthorized modification of the devices included with the wireless adapter kit or the substitution or attachment of connecting cables and equipment other than that specified by Intel Corporation. The correction of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Intel Corporation and authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines. China:
Local Restriction of 802.11a, 802.11b, 802.11g, 802.11n, and 802.11e Radio Usage The following statement on local restrictions must be published as part of the compliance documentation for all 802.11a, 802.11b, 802.11g and 802.11n products. Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e wireless LAN devices may not yet be harmonized in all countries, 802.11a, 802.11b, 802.11g, 802.11n, and 802.16e products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such. Intel WiFi Adapters, 802.11n and 802.11ac Compliant The information in this section applies to the following products:
Intel Centrino Wireless-N 100 Intel Centrino Wireless-N 105 Intel Centrino Wireless-N 130 Intel Centrino Wireless-N 135 Intel Centrino Wireless-N 1000 Intel Centrino Wireless-N 1030 Intel Centrino Wireless-N 2200 Intel Centrino Wireless-N 2230 Intel Centrino Advanced-N 6200 Intel Centrino Advanced-N 6205 Intel Centrino Advanced-N 6230 Intel Centrino Advanced-N 6235 Intel Centrino Ultimate-N 6300 Intel Dual Band Wireless-AC 7260 Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Intel Dual Band Wireless-AC 3160 Intel Dual Band Wireless-AC 3165 Intel Dual Band Wireless-AC 3168 Intel Dual Band Wireless-AC 7265 Intel Dual Band Wireless-N 7265 Intel Wireless-N 7265 Intel Dual Band Wireless-AC 8260 Intel Dual Band Wireless-AC 8265 Intel Wireless-AC 9260 Intel Wireless-AC 9461 Intel Wireless-AC 9462 Intel Wireless-AC 9560 Intel Tri-Band Wireless-AC 17265 Intel Tri-Band Wireless-AC 18260 Intel Tri-Band Wireless-AC 18265 Intel Wireless Gigabit Sink W13100 Intel Wireless Gigabit 11000 Intel Wireless Gigabit Sink W13110VR Intel Wireless Gigabit 11100VR Intel Wi-Fi 6 AX201/ 14T90N See Specifications for complete wireless adapter specifications. NOTE: In this section, all references to the "wireless adapter" refer to all adapters listed above. The following information is provided:
Information for the User Regulatory Information Regulatory ID Information for OEMs and Host Integrators Statements of European Compliance INFORMATION FOR THE USER Safety Notices USA FCC Radio Frequency Exposure The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. The wireless adapter meets the Human Exposure requirements found in FCC Part 2, 15C, 15E along with guidance from KDB 447498, KDB 248227 and KDB 616217. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCCs recommended limits. The following safety precautions should be observed:
Do not touch or move antenna while the unit is transmitting or receiving. Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting. Do not operate the radio or attempt to transmit data unless the antenna is connected; this behavior may cause damage to the radio. Use in specific environments:
The use of wireless adapters in hazardous locations is limited by the constraints posed by the safety directors of such environments. The use of wireless adapters on airplanes is governed by the Federal Aviation Administration (FAA). The use of wireless adapters in hospitals is restricted to the limits set forth by each hospital. Explosive Device Proximity Warning Warning: Do not operate a portable transmitter (including this wireless adapter) near unshielded blasting caps or in an explosive environment unless the transmitter has been modified to be qualified for such use. Antenna Warnings Use On Aircraft Caution Warning: The wireless adapter is not designed for use with high-gain directional antennas. Caution: Regulations of commercial airline operators may prohibit airborne operation of certain electronic devices equipped with radio-frequency wireless devices (wireless adapters) because their signals could interfere with critical aircraft instruments. Caution: 60 GHz/802.11ad equipment is not permitted on aircraft per FCC 15.255. OEM and host integrators should consider this FCC rule in host devices. Other Wireless Devices Safety Notices for Other Devices in the Wireless Network: See the documentation supplied with wireless adapters or other devices in the wireless network. Local Restrictions on 802.11a, 802.11b, 802.11d, 802.11g, 802.11n, and 802.11ac Radio Usage Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11d, 802.11g, 802.11n, and 802.11ac wireless LAN devices may not yet be harmonized in all countries, 802.11a, 802.11b, 802.11d, 802.11g, 802.11n, and 802.11ac products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. The device transmit power control (TPC) interface is part of the Intel PROSet/Wireless WiFi Connection Utility Software. Operational restrictions for Equivalent Isotropic Radiated Power (EIRP) are provided by the system manufacturer. Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such. Wireless Interoperability The wireless adapter is designed to be interoperable with other wireless LAN products that are based on direct sequence spread spectrum (DSSS) radio technology and to comply with the following standards:
IEEE Std. 802.11b compliant Standard on Wireless LAN IEEE Std. 802.11g compliant Standard on Wireless LAN IEEE Std. 802.11a compliant Standard on Wireless LAN IEEE Std. 802.11n compliant Standard on Wireless LAN IEEE Std. 802.11ac draft compliant on Wireless LAN Wireless Fidelity certification, as defined by the Wi-Fi Alliance The Wireless Adapter and Your Health The wireless adapter, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by the wireless adapter, however, is less than the electromagnetic energy emitted by other wireless devices such as mobile phones. The wireless adapter operates within the guidelines found in radio frequency safety standards and recommendations. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of the wireless adapter may be restricted by the proprietor of the building or responsible representatives of the applicable organization. Examples of such situations may include:
Using the wireless adapter on board airplanes, or Using the wireless adapter in any other environment where the risk of interference with other devices or services is perceived or identified as being harmful. If you are uncertain of the policy that applies to the use of wireless adapters in a specific organization or environment (an airport, for example), you are encouraged to ask for authorization to use the adapter before you turn it on. REGULATORY INFORMATION USA - Federal Communications Commission (FCC) This wireless adapter is restricted to indoor use due to its operation in the 5.15 to 5.25 and 5.470 to 5.75GHz frequency ranges. No configuration controls are provided for Intel wireless adapters allowing any change in the frequency of operations outside the FCC grant of authorization for U.S. operation according to Part 15.407 of the FCC rules. Intel wireless adapters are intended for OEM integrators only. Intel wireless adapters cannot be co-located with any other transmitter unless approved by the FCC. This wireless adapter complies with Part 15 of the FCC Rules. Operation of the device is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference that may cause undesired operation. NOTE: The radiated output power of the adapter is far below the FCC radio frequency exposure limits. Nevertheless, the adapter should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, you should keep a distance of at least 20cm between you (or any other person in the vicinity), or the minimum separation distance as specified by the FCC grant conditions, and the antenna that is built into the computer. Details of the authorized configurations can be found at http://www.fcc.gov/oet/ea/
by entering the FCC ID number on the device. Class B Device Interference Statement This wireless adapter has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This wireless adapter generates, uses, and can radiate radio frequency energy. If the wireless adapter is not installed and used in accordance with the instructions, the wireless adapter may cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this wireless adapter does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:
Reorient or relocate the receiving antenna of the equipment experiencing the interference. Increase the distance between the wireless adapter and the equipment experiencing the interference. Connect the computer with the wireless adapter to an outlet on a circuit different from that to which the equipment experiencing the interference is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE: The adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any other installation or use will violate FCC Part 15 regulations. Safety Approval Considerations This device has been safety approved as a component and is for use only in complete equipment where the acceptability of the combination is determined by the appropriate safety agencies. When installed, consideration must be given to the following:
It must be installed into a compliant host device meeting the requirement of UL/EN/IEC 60950-1 2nd edition including the general provisions of enclosure design 1.6.2 and specifically paragraph 1.2.6.2 (Fire Enclosure). The device shall be supplied by a SELV source when installed in the end-use equipment. A heating test shall be considered in the end-use product for meeting the requirement of UL/EN/IEC 60950-1 2nd edition. Low Halogen Applies only to brominated and chlorinated flame retardants (BFRs/CFRs) and PVC in the final product. Intel components as well as purchased components on the finished assembly meet JS-709 requirements, and the PCB /
substrate meet IEC 61249-2-21 requirements. The replacement of halogenated flame retardants and/or PVC may not be better for the environment. Canada Industry Canada (IC) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil se conforme aux normes Canada d'Industrie de RSS permis-exempt. L'utilisation est assujetti aux deux conditions suivantes: (1) cet appareil ne peut pas causer d'interfrences, et (2) cet appareil doit accepter des interfrences , y compris des interfrences qui peuvent causer desoprations non dsires de l'appareil. Caution: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use due to its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15GHz to 5.25GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65 to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The maximum allowed antenna gain for use with this device is 6dBi in order to comply with the E.I.R.P limit for the 5.25- to 5.35 and 5.725 to 5.85GHz frequency range in point-to-point operation. To comply with RF exposure requirements all antennas should be located at a minimum distance of 20cm, or the minimum separation distance allowed by the module approval, from the body of all persons. Attention: l'utilisation d'un rseau sans fil IEEE802.11a est restreinte une utilisation en intrieur cause du fonctionnement dans la bande de frquence 5.15-5.25 GHz. Industry Canada requiert que ce produit soit utilis l'intrieur des btiments pour la bande de frquence 5.15-5.25 GHz afin de rduire les possibilits d'interfrences nuisibles aux canaux co-existants des systmes de transmission satellites. Les radars de puissances ont fait l'objet d'une allocation primaire de frquences dans les bandes 5.25-5.35 GHz et 5.65-5.85 GHz. Ces stations radar peuvent crer des interfrences avec ce produit et/ou lui tre nuisible. Le gain d'antenne maximum permissible pour une utilisation avec ce produit est de 6 dBi afin d'tre conforme aux limites de puissance isotropique rayonne quivalente (P.I.R.E.) applicable dans les bandes 5.25-5.35 GHz et 5.725-5.85 GHz en fonctionnement point--point. Pour se conformer aux conditions d'exposition de RF toutes les antennes devraient tre localises une distance minimum de 20 cm, ou la distance de sparation minimum permise par l'approbation du module, du corps de toutes les personnes. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication. Selon les rglements de Canada d'Industrie, cet metteur de radio peut seulement fonctionner en utilisant une antenne du type et de gain maximum (ou moindre) que le gain approuv pour l'metteur par Canada d'Industrie. Pour rduire lesinterfrences radio potentielles avec les autres utilisateurs, le type d'antenne et son gain devraient tre choisis de faon ce que la puissance isotrope rayonne quivalente(P.I.R.E.) ne soit pas suprieure celle qui est ncessaire pour une communication russie. European Union The low band 5.15 - 5.35GHz is for indoor use only. This equipment complies with the essential requirements of the European Union directive 2014/53/EU. See Statements of European Union Compliance. European Union Declarations of Conformity To view the European Union Declaration of Conformity for your adapter, perform these steps. 1. Open this web site: http://www.intel.com/content/www/us/en/support/network-and-i-o/wireless-
networking/000007443.html 2. Click on "User Guide."
3. Scroll to your adapter. To view additional regulatory information for your adapter, perform these steps:
1. Open this web site: http://www.intel.com/content/www/us/en/support/network-and-i-o/wireless-
networking/000007443.html 2. Click on the link for your adapter. 3. Click on Regulatory Marking Document for your adapter. Waste Electrical and Electronic Equipment Directive (WEEE) Restriction of Hazardous Substances Directive (RoHS) Compliant All products described herein are compliant with the European Union's RoHS Directive. For CE Mark-Related Questions related to the wireless adapter, contact:
Intel Corporation Attn: Corporate Quality 2200 Mission College Blvd. Santa Clara, CA 95054-1549 USA
. 5150-5250MHz . La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. The operation of this product in the radio channel 2 (2417 MHz) is not authorized in the following cities: Agadir, Assa-Zag, Cabo Negro, Chaouen, Goulmima, Oujda, Tan Tan, Taourirt, Taroudant and Taza. The operation of this product in the radio channels 4, 5, 6 et 7 (2425 - 2442 MHz) is not authorized in the following cities: Aroport Mohamed V, Agadir, Aguelmous, Anza, Benslimane, Bni Hafida, Cabo Negro, Casablanca, Fs, Lakbab, Marrakech, Merchich, Mohammdia, Rabat, Sal, Tanger, Tan Tan, Taounate, Tit Mellil, Zag. 5GHz Japan Korea Mexico Morocco Pakistan
"PTA APPROVED MODEL"
Taiwan
, 5.25-5.35 Singapore Radio Approvals To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer's OEM Regulatory Guidance document. Modular Regulatory Certification Country Markings A list of countries requiring regulatory markings is available. Note that the lists include only countries requiring marking but not all certified countries. To find the regulatory country marking information for your adapter, perform these steps:
1. Open this web site: http://www.intel.com/content/www/us/en/support/network-and-i-o/wireless-
networking/000007443.html 2. Click on the link for your adapter. 3. Click on Regulatory Marking Document for your adapter. Regulatory ID Europe: Models 3160HMW, 3160NGW, 3160SDW, 3165NGW, 7260SDW, 7260NGW, 7260HMW, 7265D2W, 7265NGW, 8260D2W, 8260NGW, 8260NGWH, 18260NGW Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions
(WiFi/BT) Intel Wireless Dock Manager 3.x and previous versions (WiGig) Maximum Power Output
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode
(2400 - 2483.5 MHz) BLE / Bluetooth
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode 20dBm EIRP max (100mW) 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category
(57 - 64 GHz) IEEE802.11 ad mode 2 receiver 25 dBm EIRP max This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Intel Dual Band Wireless-AC 3165 Due to the very small size of the 3165D2W/3165NGW (12x16), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 3165D2W, FCC ID: PD93165D2 Canada: Model 3165D2W, IC: 1000M-3165D2 Japan: Model 3165D2W:
Korea: Model 3165D2W, MSIP-CRM-INT-7265D2W Taiwan: Model 3165D2W, China: Model 3165D2W, CMIIT ID: 2015AJ3466 (M) Europe: Model 3165D2W Maximum Power Output 20dBm EIRP max (100mW)
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode
(2400 - 2483.5 MHz) Bluetooth/BLE 10dBm EIRP max (10mW)
(5150 - 5725 MHz) 23dBm EIRP max (200mW) Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Australia: Model 3165D2W Singapore: Model 3165D2W Argentina:
Model 3165D2W, Model 3165NGW, Intel Dual Band Wireless-AC 3168 Due to the very small size of the 3168NGW, the marking has been placed in this user manual because the product label on the device is considered too small to be readable. Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Maximum Power Output 20dBm EIRP max (100mW) 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Europe: Model 3168NGW
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode
(2400 - 2483.5 MHz) Bluetooth/BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode Argentina: Model 3168NGW, Intel Dual Band Wireless-AC 7265 Due to the very small size of the 7265D2W (12x16), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 7265D2W, FCC ID: PD97265D2 Canada: Model 7265D2W, IC: 1000M-7265D2 Japan: Model 7265D2W:
Korea: Model 7265D2W, MSIP-CRM-INT-7265D2W Taiwan: Model 7265D2W, China: Model 7265D2W, CMIIT ID: 2014AJ3467 (M) Australia: Model 7265D2W, Argentina: Model 7265D2W, Intel Wireless Gigabit Sink W13100 Due to the very small size of the 13100NGW, the marking has been placed in this user manual because the product label on the device is considered too small to be readable. Software Version Intel Wireless Dock Manager 3.x and previous versions Europe: Model 13100NGW Maximum Power Output
(57 - 64 GHz) IEEE802.11 ad mode 25 dBm EIRP max This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Singapore: Model 13100NGW Intel Tri-Band Wireless-AC 17265 Due to the very small size of the 17265NGW, the marking has been placed in this user manual because the product label on the device is considered too small to be readable. Europe: Model 17265NGW Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions
(WiFi/BT) Intel Wireless Dock Manager 3.x and previous versions (WiGig) Maximum Power Output 20dBm EIRP max (100mW) 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver 25 dBm EIRP max This equipment complies with the essential requirements of the European Union directive 2014/53/EU.
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode
(57 - 64 GHz) IEEE802.11 ad mode Singapore: Model 17265NGW Intel Dual Band Wireless-AC 8260 Due to the very small size of the 8260D2W (12x16), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 8260D2W, FCC ID: PD98260D2 (FCC ID without suffix "U" denotes factory installation only);
FCC ID: PD98260D2U (FCC ID with suffix U denotes user installation or replacement permitted and supported by bios locking feature) Canada: Model 8260D2W, IC: 1000M-8260D2 Japan: Model 8260D2W:
Korea: Model 8260D2W, MSIP-CRM-INT-8260D2W Taiwan: Model 8260D2W, China: Model 8260D2W, CMIIT ID: 2014AJ3467 (M) Australia: Model 8260D2W, Argentina: Model 8260D2W, Due to the very small size of the 8260NGWH/8260NGW, the marking has been placed in this user manual because the product label on the device is considered too small to be readable. Argentina: Model 8260NGWH, Argentina: Model 8260NGW, Intel Dual Band Wireless-AC 8265 Due to the very small size of the 8265NGW (22mm x 30mm x 2.4mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 8265NGW FCC ID: PD98265NG (FCC ID without suffix "U" denotes factory installation only) FCC ID: PD98265NGU (FCC ID with suffix U denotes user installation or replacement permitted and supported by BIOS locking feature) Canada: Model 8265NGW, IC: 1000M-8265NG Japan: Model 8265NGW:
RF 003-160104 TEL D160055003 Korea: Model 8265NGW, MSIP-CRM-INT-8265NGW, Taiwan: Model 8265NGW China: Model 8265NGW Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Europe: Models 8265NGW, 8265D2W Maximum Power Output
(2400 - 2483.5 MHz) 20dBm EIRP max (100mW) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode
(57 - 64 GHz) IEEE802.11 ad mode 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver 25 dBm EIRP max This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Australia: Model 8265NGW, Brazil: Model 8265NGW: ANATEL: XXXXXXXXXX, Argentina: Model 8265NGW, Singapore: Model 8265NGW:
Pakistan: Model 8265NGW
"PTA APPROVED MODEL"
Due to the very small size of the 8265D2W (12mm x 16mm x 1.8mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 8265D2W, FCC ID: PD98265D2 Canada: Model 8265D2W, IC: 1000M-8265D2 Japan: Model 8265D2W:
RF 003-160129 TEL D160076003 Korea: Model 8265D2W, MSIP-CRM-INT-8265D2W, Taiwan: Model 8265D2W China: Model 8265D2W Australia: Model 8265D2W, Brazil: Model 8265D2W: ANATEL: XXXXXXXXXX, Argentina: Model 8265D2W, Singapore: Model 8265D2W:
Due to the very small size of the 9260NGW (22mm x 30mm x 2.4mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. Pakistan: Model 8265D2W
"PTA APPROVED MODEL"
Intel Wireless-AC 9260 USA: Model 9260NGW, FCC ID: PD99260NG Canada: Model 9260NGW, IC: 1000M-9260NG Japan: Model 9260NGW:
RF 003-170125 TEL D170079003 Korea: Model 9260NGW, MSIP-CRM-INT-9260NGW Taiwan: Model 9260NGW China: Model 9260NGW Europe: Model 9260NGW Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Maximum Power Output
(2400 - 2483.5 MHz) IEEE802.11 b/g/n 20dBm EIRP max (100mW) mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Australia: Model 9260NGW Singapore: Model 9260NGW Intel Wireless-AC 9461 (Model 9461NGW) Due to the very small size of the 9461NGW (22mm x 30mm x 2.4mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 9461NGW, FCC ID: PD99461NG Canada: Model 9461NGW, IC: 1000M-9461NG Japan: Model 9461NGW:
RF 003-170204 TEL D170127003 Korea: Model 9461NGW MSIP-CRM-INT-9461NGW Taiwan: Model 9461NGW China: Model 9461NGW Europe: Model 9461NGW
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Maximum Power Output 20dBm EIRP max (100mW) 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Intel Wireless-AC 9461 (Model 9461D2W) Due to the very small size of the 9461D2W (12mm x 16mm x 1.8mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 9461D2W, FCC ID: PD99461D2 Canada: Model 9461D2W, IC: 1000M-9461D2 Japan: Model 9461D2W:
RF 003-170203 TEL D170126003 Australia: Model 9461NGW Singapore: Model 9461NGW Korea: Model 9461D2W MSIP-CRM-INT-9461D2W Taiwan: Model 9461D2W Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Maximum Power Output 20dBm EIRP max (100mW) 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. China: Model 9461D2W Europe: Model 9461D2W
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode Australia: Model 9461D2W Singapore: Model 9461D2W Intel Wireless-AC 9462 (Model 9462NGW) Due to the very small size of the 9462NGW (22mm x 30mm x 2.4mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 9462NGW, FCC ID: PD99462NG Canada: Model 9462NGW, IC: 1000M-9462NG Japan: Model 9462NGW:
RF 003-170245 TEL D170151003 Korea: Model 9462NGW R-CRM-INT-9462NGW Taiwan: Model 9462NGW China: Model 9462NGW Europe: Model 9462NGW Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Maximum Power Output 20dBm EIRP max (100mW)
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE 10dBm EIRP max (10mW)
(5150 - 5725 MHz) 23dBm EIRP max (200mW) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Intel Wireless-AC 9462 (Model 9462D2W) Due to the very small size of the 9462D2W (12mm x 16mm x 1.8mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. Australia: Model 9462NGW Singapore: Model 9462NGW USA: Model 9462D2W, FCC ID: PD99462D2 Canada: Model 9462D2W, IC: 1000M-9462D2 Japan: Model 9462D2W:
RF 003-170243 TEL D170149003 Korea: Model 9462D2W Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Maximum Power Output 20dBm EIRP max (100mW) 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. R-CRM-INT-9462D2W Taiwan: Model 9462D2W China: Model 9462D2W Europe: Model 9462D2W
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode Australia: Model 9462D2W Singapore: Model 9462D2W Intel Wireless-AC 9560 (Model 9560NGW) Due to the very small size of the 9560NGW (22mm x 30mm x 2.4mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 9560NGW, FCC ID: PD99560NG Canada: Model 9560NGW, IC: 1000M-9560NG Japan: Model 9560NGW:
RF 003-170126 TEL D170080003 Korea: Model 9560NGW, MSIP-CRM-INT-9560NGW Taiwan: Model 9560NGW and 9560NGW R:
China: Model 9560NGW Europe: Model 9560NGW Maximum Power Output
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions 20dBm EIRP max (100mW)
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Australia: Model 9560NGW Singapore: Model 9560NGW Intel Wireless-AC 9560 (Model 9560D2W) Due to the very small size of the 9560D2W (12mm x 16mm x 1.8mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 9560D2W, FCC ID: PD99560D2 Canada: Model 9560D2W, IC: 1000M-9560D2 Japan: Model 9560D2W:
RF 003-170244 TEL D170150003 Korea: Model 9560D2W R-CRM-INT-9560D2W Taiwan: Model 9560D2W China: Model 9560D2W Europe: Model 9560D2W
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Maximum Power Output 20dBm EIRP max (100mW) 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Intel Wireless-AC 9560 (Model 9560D2WL) Due to the very small size of the 9560D2WL (12mm x 16mm x 1.8mm), the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 9560D2WL, FCC ID: PD99560D2L Canada: Model 9560D2WL, IC: 1000M-9560D2L Japan: Model 9560D2WL:
RF 003-180060 TEL D180033003 Australia: Model 9560D2W Singapore: Model 9560D2W Korea: Model 9560D2WL R-CRM-INT-9560D2WL Taiwan: Model 9560D2WL Software Version Intel PROSet/Wireless WiFi Software 20.x and subsequent versions Maximum Power Output 20dBm EIRP max (100mW) 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver This equipment complies with the essential requirements of the European Union directive 2014/53/EU. China: Model 9560D2WL Europe: Model 9560D2WL
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode Australia: Model 9560D2WL Singapore: Model 9560D2WL Intel Tri-band Wireless AC 18265 Due to the very small size of the 18265NGW module, the regulatory marking has been placed in this user manual because the product label on the device is considered too small to be readable USA: Model 18265NGW, FCC ID: PD918265NG (This module is for factory installation only) Canada: Model 18265NGW, IC : 1000M-18265NG Japan: Model 18265NGW Korea: Model 18265NGW, MSIP-CRM-INT-18265NGW Taiwan: Model 18265NGW China: Model 18265NGW, CMIIT ID: 2016AJ7066 (M) Europe: Model 18265NGW, Software Version Maximum Power Output 20dBm EIRP max (100mW) Intel PROSet/Wireless WiFi Software 20.x and subsequent versions
(WiFi/BT) Intel Wireless Dock Manager 3.x and previous versions (WiGig)
(2400 - 2483.5 MHz) IEEE802.11 b/g/n mode Bluetooth
(2400 - 2483.5 MHz) BLE
(5150 - 5725 MHz) IEEE802.11 a/n/ac mode
(5725 - 5875 MHz) IEEE802.11 a/n/ac mode 10dBm EIRP max (10mW) 23dBm EIRP max (200mW) The low band 5.15 - 5.35 GHz is for indoor use only 13.98 dBm EIRP Max (25mW) For the standard EN 300 440, the device operating in 5.8 GHz is considered a category 2 receiver
(57 - 64 GHz) IEEE802.11 ad mode 25 dBm EIRP max This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Australia: Model 18265NGW, Brazil: Model 18265NGW, ANATEL: XXXXXXXXXXXXX Singapore: Model 18265NGW, Intel Wireless Gigabit 11000 Due to the very small size of the 11000D2W/11000D2W LC, the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 11000D2W and 11000D2W LC, FCC ID: PD911000D2 Canada: Model 11000D2W, IC: 1000M-11000D2 Japan: Model 11000D2W:
Korea: Model 11000D2W, MSIP-CRM-INT-11000D2W Taiwan: Model 11000D2W and 11000D2W LC, China: Model 11000D2W, CMIIT ID: 2016DJ0267 (M); Model 11000D2W LC, CMIIT ID: 2016DJ0268 (M) Software Version Intel Wireless Dock Manager 3.x and previous versions Europe: Model 11000D2W Maximum Power Output
(57 - 64 GHz) IEEE802.11 ad mode 25 dBm EIRP max Australia: Model 11000D2W, Singapore: Model 11000D2W/11000D2W LC:
Intel Wireless Gigabit Sink W13110VR Due to the very small size of the 13110NGW, the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 13110NGW, FCC ID: PD913110NG Canada: Model 13110NGW, IC: 1000M-13110NG Korea: Model 13110NGW, R-CRM-INT-13110NGW Taiwan: Model 13110NGW Europe: Model 13110NGW Software Version Intel Wireless VR dashboard 4.x Maximum Power Output
(57 - 64 GHz) IEEE802.11ad mode 25 dBm EIRP max This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Singapore: Model 13110NGW Intel Wireless Gigabit 11100VR Due to the very small size of the 11100D2W, the marking has been placed in this user manual because the product label on the device is considered too small to be readable. USA: Model 11100D2W, FCC ID: PD911100D2 Canada: Model 11100D2W, IC: 1000M-11100D2 Korea: Model 11100D2W, R-CRM-INT-11100D2W Taiwan: Model 11100D2W Europe: Model 11100D2W Software Version Intel Wireless VR Dashboard 4.x Maximum Power Output
(57 - 64 GHz) IEEE802.11ad mode 26 dBm EIRP max This equipment complies with the essential requirements of the European Union directive 2014/53/EU. Australia: Model 11100D2W Singapore: Model 11100D2W Intel Wi-Fi 6 AX201/ 14T90N Models:
AX201NGW (M.2 2230) AX201D2W (M.2 1216) AX201D2WL (M.2 1216, LTE coex)
(Details TBD) INFORMATION FOR OEMS and HOST INTEGRATORS The guidelines described within this document are provided to OEM integrators installing Intel wireless adapters in notebook and tablet PC host platforms. Adherence to these requirements is necessary to meet the conditions of compliance with FCC rules, including RF exposure. When all antenna type and placement guidelines described herein are fulfilled the Intel wireless adapters may be incorporated into notebook and tablet PC host platforms with no further restrictions. If any of the guidelines described herein are not satisfied it may be necessary for the OEM or integrator to perform additional testing and/or obtain additional approval. The OEM or integrator is responsible to determine the required host regulatory testing and/or obtaining the required host approvals for compliance. Intel wireless adapters are intended for OEMs and host integrators only. The Intel wireless adapter FCC Grant of Authorization describes any limited conditions of modular approval. The Intel wireless adapters must be operated with an access point that has been approved for the country of operation. Changes or modification to Intel wireless adapters by OEMs, integrators or other third parties is not permitted. Any changes or modification to Intel wireless adapters by OEMs, integrators or other third parties will void authorization to operate the adapter. Antenna Type and Gains Only antennas of the same type and with equal or less gains as shown below may be used with the Intel wireless adapters. Other types of antennas and/or higher gain antennas may require additional authorization for operation. Antenna Location
(Main/Aux) 2.4GHz Peak Gain in dBi*
2.6GHz Peak Gain in dBi*
5.2GHz Peak Gain in dBi*
5.5GHz Peak Gain in dBi*
5.7GHz Peak Gain in dBi*
3.24 3.47 3.73 4.77 4.77 Antenna Type PIFA Main Aux MIMO
*All antenna gains include cable loss. Antenna Placement Within the Host Platform To ensure RF exposure compliance the antenna(s) used with the Intel wireless adapters must be installed in notebook or tablet PC host platforms to provide a minimum separation distance from all persons, in all operating modes and orientations of the host platform, with strict adherence to the table below. The antenna separation distance applies to both horizontal and vertical orientation of the antenna when installed in the host system. Wireless Adapter Minimum required antenna-to-user separation distance Intel Centrino Wireless-N 100 Intel Centrino Wireless-N 105 Intel Centrino Wireless-N 130 Intel Centrino Wireless-N 135 Intel Centrino Wireless-N 1000*
Intel Centrino Wireless-N 1030 Intel Centrino Wireless-N 2200 Intel Centrino Wireless-N 2230 Intel Centrino Advanced-N 6200*
Intel Centrino Advanced-N 6205 Intel Centrino Advanced-N 6230 Intel Centrino Advanced-N 6235 Intel Centrino Ultimate-N 6300 Intel Dual Band Wireless-AC 7260 Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Intel Dual Band Wireless-AC 3160 Intel Dual Band Wireless-AC 3165 Intel Dual Band Wireless-AC 7265 Intel Dual Band Wireless-N 7265 Intel Wireless-N 7265 Intel Dual Band Wireless-AC 8260 Intel Dual Band Wireless-AC 8265 Intel Wireless-AC 9260 Intel Wireless-AC 9461 (9161NGW) Intel Wireless-AC 9461 (9161D2W) Intel Wireless-AC 9462 (9162NGW) Intel Wireless-AC 9462 (9162D2W) Intel Wireless-AC 9560 (9560NGW) Intel Wireless-AC 9560 (9560D2W) 9 mm 9 mm 8 mm 9 mm 20 mm 8 mm 9 mm 6 mm 20 mm 12 mm 12 mm 8 mm 13 mm 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 14 mm 19 mm 12 mm 14 mm 15 mm 18 mm 15 mm Intel Wireless-AC 9560 (9560D2WL) Intel Tri-Band Wireless-AC 17265 Intel Tri-Band Wireless-AC 18260 Intel Tri-Band Wireless-AC 18265 Intel Wireless Gigabit Sink W13100 Intel Wireless Gigabit 11000 Intel Wireless Gigabit Sink W13110VR Intel Wireless Gigabit 11100VR Intel Wi-Fi 6 AX201/ 14T90N TBD 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm TBD
* This wireless adapter may be installed in mobile devices only (requires > 20 cm antenna separation from the body of user). For WiFi/Bluetooth combination adapters it is recommended that a 5 cm separation distance between transmitting antennas be provided within the host system to maintain an adequate separation ratio for simultaneous WiFi and Bluetooth transmission. For less than 5 cm separation the separation ratio must be verified according to FCC publication KDB 447498 for the specific adapter. Additional regulatory authorization process may be required if wishing to place the 60 GHz/802.11ad RFEM (antenna array) closer than 20 cm to the user. Simultaneous Transmission of Intel Wireless Adapters with Other Integrated or Plug-In Transmitters Based upon FCC Knowledge Database publication number 616217, when there are multiple transmitting devices installed in a host device, an RF exposure transmitting assessment shall be performed to determine the necessary application and test requirements. OEM integrators must identify all possible combinations of simultaneous transmission configurations for all transmitters and antennas installed in the host system. This includes transmitters installed in the host as mobile devices (>20 cm separation from user) and portable devices (<20 cm separation from user). OEM integrators should consult the actual FCC KDB 616217 document for all details in making this assessment to determine if any additional requirements for testing or FCC approval is necessary. Information To Be Supplied to the End User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating the Intel wireless adapter, in compliance with local regulations. Host system must be labeled with "Contains FCC ID: XXXXXXXX", FCC ID displayed on label. The wireless adapter must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. For country-specific approvals, see Radio Approvals. Intel Corporation is not responsible for any radio or television interference caused by unauthorized modification of the devices included with the wireless adapter kit or the substitution or attachment of connecting cables and equipment other than that specified by Intel Corporation. The correction of interference caused by such unauthorized modification, substitution or attachment is the responsibility of the user. Intel Corporation and authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from the user failing to comply with these guidelines. China:
Local Restriction of 802.11a, 802.11b, 802.11g, 802.11n, and 802.11ad Radio Usage The following statement on local restrictions must be published as part of the compliance documentation for all 802.11a, 802.11b, 802.11g, 802.11n, and 802.11ad products. Caution: Due to the fact that the frequencies used by 802.11a, 802.11b, 802.11g, 802.11n, and 802.11ad wireless LAN devices may not yet be harmonized in all countries, 802.11a, 802.11b, 802.11g and 802.11n products are designed for use only in specific countries, and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use. Any deviation from permissible settings and restrictions in the country of use could be an infringement of national law and may be punished as such. Statements of European Compliance Each of the adapters listed below comply with the essential requirements of the European Union directive 2014/53/EU. Intel Centrino Wireless-N 100 Intel Centrino Wireless-N 105 Intel Centrino Wireless-N 130 Intel Centrino Wireless-N 135 Intel Centrino Wireless-N 1000 Intel Centrino Wireless-N 1030 Intel Centrino Wireless-N 2200 Intel Centrino Wireless-N 2230 Intel Centrino Advanced-N 6200 Intel Centrino Advanced-N 6205 Intel Centrino Advanced-N 6230 Intel Centrino Advanced-N 6235 Intel Centrino Ultimate-N 6300 Intel Dual Band Wireless-AC 7260 Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Intel Dual Band Wireless-AC 3160 Intel Dual Band Wireless-AC 3165 Intel Dual Band Wireless-AC 7265 Intel Dual Band Wireless-N 7265 Intel Wireless-N 7265 Intel Dual Band Wireless-AC 8260 Intel Dual Band Wireless-AC 8265 Intel Wireless-AC 9260 Intel Wireless-AC 9560 Intel Tri-Band Wireless-AC 17265 Intel Tri-Band Wireless-AC 18260 Intel Tri-Band Wireless-AC 18265 Intel Wireless Gigabit Sink W13100 Intel Wireless Gigabit 11000 Intel Wireless Gigabit Sink W13110VR Intel Wireless Gigabit 11100VR Intel Wi-Fi 6 AX201/ 14T90N Back to Top Back to Contents Trademarks and Disclaimers Back to Contents Specifications This section provides specification information for the family of Intel wireless adapters. The following list may not be all inclusive. Intel Centrino Wireless-N 100 Intel Centrino Wireless-N 105 Intel Centrino Wireless-N 130 Intel Centrino Wireless-N 135 Intel Centrino Wireless-N 1000 Intel Centrino Wireless-N 1030 Intel Centrino Wireless-N 2200 Intel Centrino Wireless-N 2230 Intel Centrino Wireless-N + WiMAX 6150 Intel Centrino Advanced-N 6200 Intel Centrino Advanced-N 6205 Intel Centrino Advanced-N 6230 Intel Centrino Advanced-N 6235 Intel Centrino Advanced-N + WiMAX 6250 Intel Centrino Ultimate-N 6300 Intel Dual Band Wireless-AC 7260 Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Intel Dual Band Wireless-AC 3160 Intel Dual Band Wireless-AC 3165 Intel Dual Band Wireless-AC 3168 Intel Dual Band Wireless-AC 7265 Intel Dual Band Wireless-N 7265 Intel Wireless-N 7265 Intel Dual Band Wireless-AC 8260 Intel Dual Band Wireless-AC 8265 Intel Wireless-AC 9260 Intel Wireless-AC 9461 Intel Wireless-AC 9462 Intel Wireless-AC 9560 Intel Tri-Band Wireless-AC 17265 Intel Tri-Band Wireless-AC 18260 Intel Tri-Band Wireless-AC 18265 Intel Wireless Gigabit Sink W13100 Intel Wireless Gigabit 11000 Intel Wireless Gigabit Sink W13110VR Intel Wireless Gigabit 11100VR Intel Wi-Fi 6 AX201/ 14T90N Intel Centrino Wireless-N 100, Intel Centrino Wireless-N 105, Intel Centrino Wireless-N 130 and Intel Centrino Wireless-N 135 Form Factor Dimensions Antenna Interface Connector PCI Express* Half-Mini Card Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5 mm) Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity Connector 52-pin Mini Card edge connector 3.3 V 0 to +80 degrees Celsius 2.4 GHz (802.11b/g/n) 50% to 95% non-condensing (at temperatures of 25 C to 35 C) Frequency band 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK Wireless Medium 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. MIMO Configuration: 1X1 Tx/Rx: 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Intel Centrino Wireless-N 100: None Intel Centrino Wireless-N 105: None Intel Centrino Wireless-N 130: Bluetooth 2.1, 2.1 + EDR, 3.0, 3.0+HS Intel Centrino Wireless-N 135: Bluetooth 4.0 (Bluetooth Low-Energy and Bluetooth 3.0 +HS) Interface Voltage Operating Temperature Humidity WiFi Frequency Modulation IEEE 802.11n Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth Support General Operating Systems Windows* 7 (32-bit and 64-bit), Windows* 8 (32-bit and 64-bit), Windows* 8.1 (32-bit and 64-bit) Wi-Fi Alliance*
certification Wi-Fi* certification for 802.11b, 802.11g, 802.11n, WPA-Personal, WPA-Enterprise, WPA2-
Personal, WPA2-Enterprise, WMM, WPS Cisco Compatible Extensions certification Cisco Compatible Extensions, v4.0 IEEE Feature Sets IEEE 802.11b, 802.11g, 802.11n, 802.11e, 802.11i, 802.11d, 802.11h Architecture Infrastructure or ad hoc (peer-to-peer) operating modes Security WPA-Personal, WPA2-Personal, WPA-Enterprise, WPA2-Enterprise, AES-CCMP 128-bit, WEP 128-bit and 64-bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-AKA Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Centrino Wireless-N 1000 Form Factor SKUs Dimensions PCI Express* Mini Card and Half-Mini Card Intel Centrino Wireless-N 1000 - 1X2 MC/HMC Mini Card: Width 2.0 in x Length 1.18 in x Height 0.18 in (50.80 mm x 30 mm x 4.5 mm) Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5 mm) Antenna Interface Connector Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity Connector Interface 52-pin Mini Card edge connector Voltage 3.3 V Operating Temperature 0 to +80 degrees Celsius Humidity WiFi 50% to 90% non-condensing (at temperatures of 25 C to 35 C) Frequency Modulation 2.4 GHz (802.11b/g/n) Frequency band 2.41-2.474 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, CCK, DQPSK, DBPSK Wireless Medium 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates General Operating Systems 300, 270, 243, 240, 180, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Microsoft Windows* XP (32 and 64 bit) and Windows Vista* (32 and 64 bit), Ubuntu Linux*
Wi-Fi Alliance*
certification Wi-Fi* certification for 802.11b, 802.11g, 802.11n, WPA-Personal, WPA-Enterprise, WPA2-Personal, WPA2-Enterprise, WMM, WPS Cisco Compatible Extensions certification Cisco Compatible Extensions, v4.0 WLAN Standard IEEE 802.11g, 802.11b, 802.11n, 802.11d, 802.11e, 802.11i, Architecture Security Infrastructure or ad hoc (peer-to-peer) operating modes WPA-Personal, WPA2-Personal, WPA-Enterprise, WPA2-Enterprise, 802.1X: EAP-SIM, LEAP, PEAP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-AKA Encryption AES-CCMP 128-bit, WEP 128-bit and 64-bit, CKIP, TKIP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Centrino Wireless-N 2200 and Intel Centrino Wireless-N 2230 PCI Express* Half-Mini Card Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5 mm) Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Form Factor Dimensions Antenna Interface Connector Connector Interface Voltage Operating Temperature Antenna Diversity On-board diversity 52-pin Mini Card edge connector 3.3 V 0 to +80 degrees Celsius 50% to 95% non-condensing (at temperatures of 25 C to 35 C) 2.4 GHz (802.11b/g/n) Frequency band 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK Wireless Medium 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. MIMO Configuration: 2X2 Tx/Rx: 300, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Intel Centrino Wireless-N 2200: None Intel Centrino Wireless-N 2230: Bluetooth 4.0 (Bluetooth Low-Energy and Bluetooth 3.0 +HS) Humidity WiFi Frequency Modulation IEEE 802.11n Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth Support General Operating Systems Windows* 7 (32-bit and 64-bit), Windows* 8 (32-bit and 64-bit), Windows* 8.1 (32-bit and 64-bit) Wi-Fi Alliance*
certification Wi-Fi* certification for 802.11b, 802.11g, 802.11n, WPA-Personal, WPA-Enterprise, WPA2-
Personal, WPA2-Enterprise, WMM, WPS Cisco Compatible Extensions certification Cisco Compatible Extensions, v4.0 IEEE Feature Sets IEEE 802.11b, 802.11g, 802.11n, 802.11e, 802.11i, 802.11d, 802.11h Architecture Infrastructure or ad hoc (peer-to-peer) operating modes Security WPA-Personal, WPA2-Personal, WPA-Enterprise, WPA2-Enterprise, AES-CCMP 128-bit, WEP 128-bit and 64-bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-AKA Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Centrino Wireless-N 1030 and Intel Centrino Advanced-N 6230 Form Factor PCI Express* Half-Mini Card Dimensions Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5 mm) Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Interface Connector Antenna Diversity Network Standards Connector Interface On-board diversity 802.11a/b/g/n (varies by adapter) and Bluetooth 3.0 + HS 52-pin Mini Card edge connector Voltage 3.3 V 0 to +80 degrees Celsius Humidity 50% to 95% non-condensing (at temperatures of 25 C to 35 C) Intel Centrino Wireless-N 1030: 802.11b/g/n Intel Centrino Advanced-N 6230: 802.11a/g/n 5 GHz (802.11a/n) 2.4 GHz (802.11b/g/n) 5.15 GHz - 5.85 GHz (dependent on country) 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK 5 GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) All channels as defined by the relevant specification and country rules. Intel Centrino Advanced-N 6230:
Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Intel Centrino Wireless-N 1030:
Rx (Mbps): 300, 270, 243, 240, 180 Tx/Rx (Mbps): 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Bluetooth Version 3.0 + HS Microsoft Windows* XP (32-bit and 64-bit) Windows Vista* (32-bit and 64-bit) Windows* 7 (32-bit and 64-bit) Windows* 8 (32-bit and 64-bit) Windows* 8.1 (32-bit and 64-bit) Wi-Fi* certification for 802.11b, 802.11g, 802.11a, 802.11h, 802.11d, WPA-Personal, WPA-
Enterprise, WPA2-Personal, WPA2-Enterprise, WPS, WMM, WMM Power Save, EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-AKA, P2P Cisco Compatible Extensions, v4.0 IEEE 802.11g, 802.11b, 802.11a, 802.11n Architecture Infrastructure or ad hoc (peer-to-peer) operating modes WPA-Personal, WPA2-Personal, WPA-Enterprise, WPA2-Enterprise, AES-CCMP 128-bit, WEP 128-bit and 64-bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-
AKA UL, C-UL, CB (IEC/EN 60950-1) Operating Temperature WiFi Network Standards Frequency Modulation Frequency band Wireless Medium Channels IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Operating Systems Wi-Fi Alliance*
certification Cisco Compatible Extensions certification WLAN Standard Security Product Safety Intel Centrino Advanced-N 6235 Form Factor PCI Express* Half-Mini Card Dimensions Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5 mm) Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 On-board diversity 802.11a/b/g/n and Bluetooth 4.0 52-pin Mini Card edge connector 3.3 V 0 to +80 degrees Celsius 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Bluetooth Version 4.0 (3.0 +HS ) Antenna Interface Connector Antenna Diversity Network Standards Connector Interface Voltage Operating Temperature Frequency Modulation Frequency band Wireless Medium Channels IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Operating Systems Wi-Fi Alliance*
certification Cisco Compatible Extensions certification WLAN Standard Humidity 50% to 95% non-condensing (at temperatures of 25 C to 35 C) 5 GHz (802.11a/n) 2.4 GHz (802.11b/g/n) 5.15 GHz - 5.85 GHz (dependent on country) 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK 5 GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) All channels as defined by the relevant specification and country rules. IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Windows* 7 (32-bit and 64-bit), Windows* 8 (32-bit and 64-bit), Windows* 8.1 (32-bit and 64-bit) Wi-Fi* certification for 802.11b, 802.11g, 802.11a, 802.11h, 802.11d, WPA-Personal, WPA-
Enterprise, WPA2-Personal, WPA2-Enterprise, WPS, WMM, WMM Power Save, EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-AKA, P2P Cisco Compatible Extensions, v4.0 IEEE 802.11g, 802.11b, 802.11a, 802.11n Architecture Infrastructure or ad hoc (peer-to-peer) operating modes Security WPA-Personal, WPA2-Personal, WPA-Enterprise, WPA2-Enterprise, AES-CCMP 128-bit, WEP 128-bit and 64-bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-
AKA Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Centrino Advanced-N + WiMAX 6250 and Intel Centrino Wireless-N + WiMAX 6150 Form Factor PCI Express* Half-Mini Card Dimensions Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5 mm) Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Interface Connector Antenna Diversity Connector Interface Voltage Operating Temperature WiFi Frequency Modulation Wireless Medium Channels IEEE 802.11n Data Rates On-board diversity 52-pin Mini Card edge connector 3.3 V 0 to +80 degrees Celsius Humidity 50% to 95% non-condensing (at temperatures of 25 C to 35 C) Intel Centrino Advanced-N + WiMAX 6250 2.4 GHz (802.11b/g/n), 5 GHz (802.11a/n) Intel Centrino Wireless-N + WiMAX 6150 2.4 GHz (802.11b/g/n) Frequency band 5.15 GHz - 5.85 GHz (dependent on country) 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK 5 GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) All channels as defined by the relevant specification and country rules. Intel Centrino Wireless-N + WiMAX 6150 MIMO Configuration: 1X2 Rx: 300, 270, 243, 240, 180 Mbps Rx/Tx: 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps Intel Centrino Advanced-N + WiMAX 6250 MIMO Configuration: 2X2 Tx/Rx: 300, 270, 243, 240, 180, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps General Operating Systems Cisco Compatible Extensions certification WiMAX General Operating Systems Standard Compliance WiMAX System Profile Feature set Microsoft Windows* XP (32-bit and 64-bit) Windows Vista* (32-bit and 64-bit) Windows* 7 (32-bit and 64-bit) Windows* 8 (32-bit and 64-bit) Windows* 8.1 (32-bit and 64-bit) Wi-Fi Alliance*
certification Wi-Fi* certification for 802.11b, 802.11g, 802.11a, 802.11h, 802.11d, WPA-Personal, WPA-
Enterprise, WPA2-Personal, WPA2-Enterprise, WMM, WMM Power Save, EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-AKA Cisco Compatible Extensions, v4.0 IEEE Feature Sets Intel Centrino Wireless-N + WiMAX 6150:
IEEE 802.11b, 802.11g, 802.11n, 802.11e, 802.11i, 802.11h, 802.11d Intel Centrino Advanced-N + WiMAX 6250:
802.11a, IEEE 802.11b, 802.11g, 802.11n, 802.11e, 802.11i, 802.11h, 802.11d Architecture Infrastructure or ad hoc (peer-to-peer) operating modes Security WPA-Personal, WPA2-Personal, WPA-Enterprise, WPA2-Enterprise, AES-CCMP 128-bit, WEP 128-bit and 64-bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-
AKA Product Safety UL, C-UL, CB (IEC/EN 60950-1) Microsoft Windows* XP (32-bit and 64-bit) Windows Vista* (32-bit and 64-bit) Windows* 7 (32-bit and 64-bit) Windows* 8 (32-bit and 64-bit) Windows* 8.1 (32-bit and 64-bit) 802.16e-2005 Corrigenda 2 (D4) Intel Centrino Wireless-N + WiMAX 6150:
Mobile WiMAX release 1, Wave II. Supports 3A and 1A/B profiles Intel Centrino Advanced-N + WiMAX 6250:
Mobile WiMAX release 1, Wave II. Supports 3A, 5A/C, 1A/B, and 5BL profiles Security Key Management Protocol (PKMv2) Encryption 128-bit CCMP (Counter-Mode/CBC-MAC) based on AES encryption Intel Centrino Wireless-N + WiMAX 6150: 2.3-2.4 GHz / 2.496-2.690 GHz Intel Centrino Advanced-N + WiMAX 6250: 2.3-2.4 GHz / 2.496-2.690 GHz / 3.4-3.8 GHz WiMAX Frequency band Wireless Medium Modulation UL - QPSK, 16 QAM DL - QPSK, 16 QAM, 64 QAM Duplex mode: TDD operations sub-carrier permutation: PUSC Scalable OFDMA (SOFDMA): 512 and 1024 FFT Intel Centrino Wireless-N + WiMAX 6150:
Channel bandwidths: 5 and 10 MHz Intel Centrino Advanced-N + WiMAX 6250:
Channel bandwidths: 5, 7, 8.75 and 10 MHz WiMAX Network Release Feature set Rate Performance RF Transmitter Output Power SPWG/NWG Release 1.5 Intel Centrino Wireless-N + WiMAX 6150:
Up to 10 Mbps DL and 4 Mbps UL @ peak rate
(OTA performance, 10MHz channel) Intel Centrino Advanced-N + WiMAX 6250:
Up to 20 Mbps DL and 6 Mbps UL @ peak rate
(OTA performance, 10MHz channel) Compliance with Power class 2 Intel Centrino Advanced-N 6200, Intel Centrino Advanced-N 6205 and Intel Centrino Ultimate-N 6300 Form Factor Intel Centrino Advanced-N 6200, Intel Centrino Ultimate-N 6300:
PCI Express* Full-Mini Card and Half-Mini Card. Intel Centrino Advanced-N 6205: PCI Express* Half-Mini Card. Dimensions Full-Mini Card: Width 2.00 in x Length 1.18 in x Height 0.18 in (50.95 mm x 30 mm x 4.5 mm) Half-Mini Card: Width 1.049 in x Length 1.18 in x Height 0.18 in (26.64 mm x 30 mm x 4.5 mm) Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 On-board diversity 52-pin Mini Card edge connector 3.3 V 0 to +80 degrees Celsius Antenna Interface Connector Antenna Diversity Connector Interface Voltage Operating Temperature Frequency Modulation Frequency band Wireless Medium Channels IEEE 802.11n Data Rates Humidity 50% to 95% non-condensing (at temperatures of 25 C to 35 C) 5 GHz (802.11a/n) 2.4 GHz (802.11b/g/n) 5.15 GHz - 5.85 GHz (dependent on country) 2.400 - 2.4835 GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK 5 GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4 GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) All channels as defined by the relevant specification and country rules. Intel Centrino Ultimate-N 6300:
Tx/Rx: 450, 405, 360, 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps Intel Centrino Advanced-N 6200, Intel Centrino Advanced-N 6205:
Tx/Rx: 300, 270, 243, 240, 180, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Microsoft Windows* XP (32-bit and 64-bit) Windows Vista* (32-bit and 64-bit) Windows* 7 (32-bit and 64-bit) Windows* 8 (32-bit and 64-bit) Windows* 8.1 (32-bit and 64-bit) IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates General Operating Systems Cisco Compatible Extensions certification WLAN Standard Security Antenna Interface Connector IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation Frequency band Wi-Fi Alliance*
certification Wi-Fi* certification for 802.11b, 802.11g, 802.11a, 802.11h, 802.11d, WPA-Personal, WPA-
Enterprise, WPA2-Personal, WPA2-Enterprise, WMM, WMM Power Save, EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-AKA Cisco Compatible Extensions, v4.0 IEEE 802.11g, 802.11b, 802.11a, 802.11n Architecture Infrastructure or ad hoc (peer-to-peer) operating modes WPA-Personal, WPA2-Personal, WPA-Enterprise, WPA2-Enterprise, AES-CCMP 128-bit, WEP 128-bit and 64-bit; 802.1X: EAP-SIM, LEAP, PEAP, TKIP, EAP-FAST, EAP-TLS, EAP-TTLS, EAP-
AKA Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-AC 7260 Form Factors Half-Mini Card and M.2 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe and USB 2.0 for both form factors Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity Intel Dual Band Wireless-AC 7260 Model 7260HMW - 802.11agn, ac, 2x2, Bluetooth 4.0, PCIe, USB, HMC Model 7260NGW - 802.11agn, ac, 2x2, Bluetooth 4.0, PCIe, USB, M.2 0 to +80 degrees Celsius 50% to 95% non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. Spatial streams Intel Dual Band Wireless-AC 7260: 2 X 2 Data Rates All data rates are theoretical maximums. Intel Dual Band Wireless-AC 7260: Up to 867 Mbps Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 IEEE 802.11ac Data Rates IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Operating Systems Wi-Fi Alliance*
certification Architecture Cisco Compatible Extensions certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Model 7260HMW Model 7260NGW Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) supported by the following adapters Windows* 7 (32-bit and 64-bit), Windows* 8 (32-bit and 64-bit), Windows* 8.1 (64-
bit) Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, TKIP WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-N 7260 Intel Wireless-N 7260 Form Factors Half-Mini Card, M.2 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe, USB 2.0 for both form factors Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Interface Connector Antenna Diversity On-board diversity IEEE 802.11 Networking Standards Intel Dual Band Wireless-N 7260 Model 7260HMW AN - 802.11agn, 2x2, Bluetooth 4.0, PCIe, USB, HMC Model 7260NGW AN - 802.11agn, 2x2, Bluetooth 4.0, PCIe, USB, M.2 Model 7260HMW NB - 802.11agn, 2x2, PCIe, USB, HMC Model 7260NGW NB - 802.11agn, 2x2, PCIe, USB, M.2 Intel Wireless-N 7260 Model 7260HMW BN - 802.11agn, 2x2, Bluetooth 4.0, PCIe, USB, M.2 Model 7260NGW BN - 802.11bgn, 2x2, Bluetooth 4.0, PCIe, USB, M.2 Operating Temperature 0 to +80 degrees Celsius Humidity 50% to 95% non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11a/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. 802.11n spatial streams All adapters: 2 X 2 spatial streams Data Rates All data rates are theoretical maximums. Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Frequency Modulation
(See above, not all bands supported by all adapters) Frequency band Modulation Wireless Medium IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) supported by the following adapters 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Model 7260HMW AN Model 7260NGW AN Model 7260HMW BN Model 7260NGW BN Windows* 7 (32-bit and 64-bit), Windows 8 (32-bit and 64-bit), Windows* 8.1 (64-
bit) Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Architecture Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 General Operating Systems Wi-Fi Alliance*
certification Cisco Compatible Extensions certification Security Authentication WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-
AKA Authentication Protocols PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 Encryption 64-bit and 128-bit WEP, AES-CCMP, TKIP Wi-Fi Direct* Encryption and Authentication WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-AC 3160 Form Factors Half-Mini Card and M.2 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe and USB 2.0 for both form factors Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity Intel Dual Band Wireless-AC 3160 Antenna Interface Connector IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation Frequency band IEEE 802.11ac Data Rates IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Model 3160HMW - 802.11agn, ac, 1x1, Bluetooth 4.0, PCIe, USB, HMC Model 3160NGW - 802.11agn, ac, 1x1, Bluetooth 4.0, PCIe, USB, M.2 0 to +80 degrees Celsius 50% to 90% non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. Spatial streams Intel Dual Band Wireless-AC 3160: 1 X 1 Data Rates All data rates are theoretical maximums. Intel Dual Band Wireless-AC 3160: Up to 433 Mbps Tx/Rx (Mbps): 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Model 3160HMW Model 3160NGW Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) supported by the following adapters Operating Systems Windows* 7 (32-bit and 64-bit), Windows 8 (32-bit and 64-bit), Windows* 8.1 (64-bit) Wi-Fi Alliance*
certification Architecture Cisco Compatible Extensions certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, TKIP WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-AC 3165 (Model 3165NGW) Form Factors M.2 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe and USB 2.0 Antenna Interface Connector Antenna Diversity On-board diversity Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 802.11abgn, 802.11ac, 802.11d, 802.11e, 802.11i, 802.11h, 802.11w 0 to +80 degrees Celsius 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) Frequency band 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. Spatial streams Intel Dual Band Wireless-AC 3165: 1 X 1 Data Rates All data rates are theoretical maximums. Intel Dual Band Wireless-AC 3165: Up to 433 Mbps Tx/Rx (Mbps): 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 IEEE 802.11ac Data Rates IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) Windows* 7 (32-bit and 64-bit), Windows* 8 (32-bit and 64-bit), Windows* 8.1 (64-
bit) Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, TKIP WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-AC 3168 Form Factors M.2 2230 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe and USB 2.0 Antenna Interface Connector Antenna Diversity On-board diversity Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 802.11abgn, 802.11ac, 802.11d, 802.11e, 802.11i, 802.11h, 802.11w 0 to +80 degrees Celsius 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) Frequency band 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. Spatial streams Intel Dual Band Wireless-AC 3168: 1 X 1 Data Rates All data rates are theoretical maximums. Intel Dual Band Wireless-AC 3168: Up to 433 Mbps Tx/Rx (Mbps): 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps Bluetooth General Operating Systems Wi-Fi Alliance*
certification Architecture Cisco Compatible Extensions certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation IEEE 802.11ac Data Rates IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Wi-Fi Alliance*
certification Architecture Cisco Compatible Extensions certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.2 (BLE) Operating Systems Linux, Windows* 8.1 (64-bit), Windows* 10 (64-bit) Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, TKIP WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-AC 7265 (Model 7265NGW) Form Factors M.2 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe and USB 2.0 Antenna Interface Connector Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity Intel Dual Band Wireless-AC 7265 Model 7265NGW - 802.11agn, ac, 2x2, Bluetooth 4.0, PCIe, USB, M.2 0 to +80 degrees Celsius 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) Frequency band 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. Spatial streams Intel Dual Band Wireless-AC 7265: 2 X 2 Data Rates All data rates are theoretical maximums. IEEE 802.11ac Data Rates Intel Dual Band Wireless-AC 7265: Up to 867 Mbps IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Operating Systems Wi-Fi Alliance*
certification Architecture Cisco Compatible Extensions certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) supported by the following adapters Model 7265NGW Windows* 7 (32-bit and 64-bit), Windows* 8 (32-bit and 64-bit), Windows* 8.1 (64-
bit) Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, TKIP WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-N 7265 (Models 7265NGW AN and 7265NGW NB) Intel Wireless-N 7265 (Model 7265NGW BN) Form Factors M.2 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe, USB 2.0 Antenna Interface Connector Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity IEEE 802.11 Networking Standards Intel Dual Band Wireless-N 7265 Model 7265NGW AN - 802.11agn, 2x2, Bluetooth 4.0, PCIe, USB, M.2 Model 7265NGW NB - 802.11agn, 2x2, PCIe, USB, M.2 Intel Wireless-N 7265 Model 7265NGW BN - 802.11bgn, 2x2, Bluetooth 4.0, PCIe, USB, M.2 Operating Temperature 0 to +80 degrees Celsius Frequency Modulation
(See above, not all bands supported by all adapters) Frequency band Modulation Wireless Medium IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Operating Systems Wi-Fi Alliance*
certification Cisco Compatible Extensions certification Security Authentication Humidity 50% to 90% non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11a/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM CCK, DQPSK, DBPSK 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. 802.11n spatial streams All adapters: 2 X 2 spatial streams Data Rates All data rates are theoretical maximums. Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Model 7265NGW AN Model 7265NGW NB Model 7265NGW BN Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) supported by the following adapters Windows* 7 (32-bit and 64-bit), Windows 8 (32-bit and 64-bit), Windows* 8.1 (64-
bit) Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Architecture Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-
AKA Authentication Protocols PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 Encryption 64-bit and 128-bit WEP, AES-CCMP, TKIP Wi-Fi Direct* Encryption and Authentication WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-AC 8260 Form Factors Half-Mini Card and M.2 (Next Generation Form Factor - NGFF) Electrical interfaces PCIe and USB 2.0 for both form factors Antenna Interface Connector Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity Intel Dual Band Wireless-AC 8260 Model 8260NGW - 802.11agn, ac, 2x2, Bluetooth 4.0, PCIe, USB, M.2 0 to +80 degrees Celsius 50% to 95% non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) Frequency band 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. Spatial streams Intel Dual Band Wireless-AC 8260: 2 X 2 Data Rates All data rates are theoretical maximums. Intel Dual Band Wireless-AC 8260: Up to 867 Mbps Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) supported by the following adapters Model 8260NGW Windows* 7 (32-bit and 64-bit), Windows* 8 (32-bit and 64-bit), Windows* 8.1 (64-
bit) Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, TKIP WPA2, AES-CCMP IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation IEEE 802.11ac Data Rates IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Operating Systems Wi-Fi Alliance*
certification Architecture Cisco Compatible Extensions certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Dual Band Wireless-AC 8265 (Models 8265NGWH/8265NGW/8265D2W) General Dimensions (H x W x D) Weight M.2 2230: 22 mm x 30 mm x 2.4 mm M.2 1216: 12 mm x 16 mm x 1.8 mm M.2 2230: 2.6g M.2 1216: 0.6g Antenna Diversity Supported Radio ON/OFF Control Supported Connector Interface M.2: PCIe, USB, or UART (M.2 1216 only) 0 to +80 degrees Celsius 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Operating Systems Microsoft Windows 7*, Microsoft Windows 8.1*, Microsoft Windows 10*, Linux* (limited feature support), Android Wi-Fi CERTIFIED* a/b/g/n/ac, WMM*, WMM-PS*, WPA*, WPA2*, WPS2*, Protected Management Frames, Wi-Fi Direct* for peer to peer device connections, Wi-Fi Miracast*
as Source. IEEE 802.11a/b/g/n/ac, 802.11d, 802.11e, 802.11h, 802.11i, 802.11w; 802.11r, 802.11k, 802.11v pending OS support; Fine Timing Measurement based on 802.11REVmc Supports seamless roaming between access points Dual Mode Bluetooth* 4.2, BLE WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 Encryption 64-bit and 128-bit WEP, 128-bit AES-CCMP WPA2-PSK, AES-CCMP Operating Temperature Humidity Wi-Fi Alliance*
certification IEEE WLAN Standard Roaming Bluetooth Security Authentication Authentication Protocols Wi-Fi Direct*
Encryption and Authentication Compliance Product Safety UL, C-UL, CB (IEC 60950-1) Model Numbers Models Model 8265NGWH Model 8265NGW 802.11ac, 2x2, Bluetooth* 4.2, PCIe, USB, LTE Coexistence, eFEM, M.2 2230 HE 802.11ac, 2x2, Bluetooth* 4.2, PCIe, USB, M.2 2230 MS Model 8265D2W 802.11ac, 2x2, Bluetooth* 4.2, PCIe, LTE Frequency Modulation Frequency band Modulation 5GHz (802.11ac/n) 5.15GHz - 5.85GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM Coexistence, M.2 1216 SD 2.4GHz (802.11b/g/n) 2.400 - 2.4835GHz (dependent on country) CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. Spatial streams Intel Dual Band Wireless-AC 8265: 2 X 2 Data Rates All data rates are theoretical maximums. IEEE 802.11ac Data Rates Intel Dual Band Wireless-AC 8265: Up to 867 Mbps IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Intel Wireless-AC 9260 (Model 9260NGW) M.2 2230: 22 mm x 30 mm x 2.4 mm General Dimensions (H x W x D) Weight M.2 2230: 2.6g Antenna Diversity Supported Radio ON/OFF Control Supported Connector Interface M.2: PCIe, USB 0 to +80 degrees Celsius Operating Temperature Humidity Operating Systems Microsoft Windows 10*, Linux* (limited feature support), Chrome*
50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Wi-Fi Alliance*
certification Wi-Fi CERTIFIED* a/b/g/n/ac with wave 2 features, WMM*, WMM-PS*, WPA*, WPA2*, WPS2*, Protected Management Frames, Wi-Fi Miracast* as Source, and Wi-Fi Direct*. IEEE WLAN Standard IEEE 802.11a/b/g/n/ac, 802.11d, 802.11e, 802.11h, 802.11i, 802.11w; 802.11r, 802.11k, 802.11v pending OS support; Fine Timing Measurement based on 802.11REVmc Supports seamless roaming between access points Bluetooth* 5 WPA* and WPA2*, 802.1X (EAP-TLS, TTLS, PEAP, EAP-SIM, EAP-AKA, EAP-AKA) PAP, CHAP, TLS, MS-CHAP*, MS-CHAPv2*
Roaming Bluetooth Security Authentication Authentication Protocols Encryption 64-bit and 128-bit WEP, 128-bit AES-CCMP WPA2-PSK, AES-CCMP Wi-Fi Direct*
Encryption and Authentication Compliance Frequency Modulation Frequency band US Government FIPS, FISMA Product Safety UL, C-UL, CB (IEC 60950-1) Model Numbers Model 9260NGW 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 802.11ac wave 2, 2x2, Bluetooth* 5, PCIe, USB, M.2 2230 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Spatial streams Intel Wireless-AC 9260: 2 X 2 Data Rates All data rates are theoretical maximums. IEEE 802.11ac Data Rates 1.73 Gbps when using 160MHz channels IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Intel Wireless-AC 9461 (Models 9461NGW/9461D2W) General Dimensions (H x W x D) Weight M.2 2230: 22 mm x 30 mm x 2.4 mm M.2 1216: 12 mm x 16 mm x 1.57 (+-0.08) mm M.2 2230: 2.7g M.2 1216: 0.7g Antenna Diversity Supported Radio ON/OFF Control Supported Connector Interface M.2: CNVio 0C to +80C Operating Temperature Humidity Operating Systems Microsoft Windows 10*, Linux* (limited feature support), Chrome 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Wi-Fi Alliance*
certification Wi-Fi CERTIFIED* a/b/g/n/ac with wave 2 features, WMM*, WMM-PS*, WPA*, WPA2*, WPS2*, Protected Management Frames, Wi-Fi Miracast* as Source, and Wi-Fi Direct IEEE WLAN Standard IEEE 802.11a/b/g/n/ac, 802.11d, 802.11e, 802.11h, 802.11i, 802.11w; 802.11r, 802.11k, 802.11v pending OS support; Fine Timing Measurement based on 802.11REVmc Supports seamless roaming between access points Bluetooth 5 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, EAP-SIM, EAP-AKA) PAP, CHAP, TLS, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, 128-bit AES-CCMP WPA2-PSK, AES-CCMP Roaming Bluetooth Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication Compliance Regulatory For a list of country approvals, please contact your local Intel representatives. US Government FIPS, FISMA Product Safety UL, C-UL, CB (IEC 60950-1) Model Numbers Models 9461NGW 9461D2W 802.11ac wave 2, 1x1, Bluetooth* 5, PCIe, USB, M.2 2230, Single Antenna 802.11ac wave 2, 1x1, Bluetooth* 5, PCIe, USB, M.2 1216, Single Antenna Frequency Modulation Frequency band Modulation 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM 2.400 - 2.4835GHz (dependent on country) CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Spatial streams Intel Wireless-AC 9461: 1 X 1 Data Rates All data rates are theoretical maximums. IEEE 802.11ac Data Rates 433 Mbps when using 80MHz channels IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Intel Wireless-AC 9462 (Models 9462NGW/9462D2W) General Dimensions (H x W x D) Weight M.2 2230: 22 mm x 30 mm x 2.4 mm M.2 1216: 12 mm x 16 mm x 1.57 (+-0.08) mm M.2 2230: 2.7g M.2 1216: 0.7g Antenna Diversity Supported Radio ON/OFF Control Supported Connector Interface M.2: CNVio 0C to +80C Operating Temperature Humidity Operating Systems Microsoft Windows 10*, Linux* (limited feature support), Chrome 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Wi-Fi Alliance*
certification Wi-Fi CERTIFIED* a/b/g/n/ac with wave 2 features, WMM*, WMM-PS*, WPA*, WPA2*, WPS2*, Protected Management Frames, Wi-Fi Miracast* as Source, and Wi-Fi Direct IEEE WLAN Standard IEEE 802.11a/b/g/n/ac, 802.11d, 802.11e, 802.11h, 802.11i, 802.11w; 802.11r, 802.11k, 802.11v pending OS support; Fine Timing Measurement based on 802.11REVmc Supports seamless roaming between access points Bluetooth 5 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, EAP-SIM, EAP-AKA) PAP, CHAP, TLS, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, 128-bit AES-CCMP WPA2-PSK, AES-CCMP Roaming Bluetooth Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication Compliance Regulatory For a list of country approvals, please contact your local Intel representatives. US Government FIPS, FISMA Product Safety UL, C-UL, CB (IEC 60950-1) Model Numbers Models 9462NGW 9462D2W 802.11ac wave 2, 1x1, Bluetooth* 5, PCIe, USB, M.2 2230, Diversity Antenna 802.11ac wave 2, 1x1, Bluetooth* 5, PCIe, USB, M.2 1216, Diversity Antenna Frequency Modulation Frequency band Modulation 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM 2.400 - 2.4835GHz (dependent on country) CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 Intel Wireless-AC 9560 (Models 9560NGW/9560D2W) Spatial streams Intel Wireless-AC 9462: 1 X 1 Data Rates All data rates are theoretical maximums. IEEE 802.11ac Data Rates 433 Mbps when using 80MHz channels IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps M.2 2230: 22 mm x 30 mm x 2.4 mm M.2 1216: 12 mm x 16 mm x 1.8 mm Antenna Diversity Supported M.2 2230: 2.6g M.2 1216: 0.6g Supported M.2: CNVio 0 to +80 degrees Celsius 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Microsoft Windows 10*, Linux* (limited feature support), Chrome*
Wi-Fi CERTIFIED* a/b/g/n/ac with wave 2 features, WMM*, WMM-PS*, WPA*, WPA2*, WPS2*, Protected Management Frames, Wi-Fi Miracast* as Source, and Wi-Fi Direct* (For Microsoft Windows* only). IEEE 802.11a/b/g/n/ac, 802.11d, 802.11e, 802.11h, 802.11i, 802.11w; 802.11r, 802.11k, 802.11v pending OS support; Fine Timing Measurement based on 802.11-2016 Supports seamless roaming between access points Bluetooth* 5 Authentication WPA* and WPA2*, 802.1X (EAP-TLS, TTLS, PEAP, EAP-SIM, EAP-AKA, EAP-AKA) PAP, CHAP, TLS, MS-CHAP*, MS-CHAPv2*
Encryption 64-bit and 128-bit WEP, 128-bit AES-CCMP WPA2-PSK, AES-CCMP General Dimensions (H x W x D) Weight Radio ON/OFF Control Connector Interface Operating Temperature Humidity Operating Systems Wi-Fi Alliance*
certification IEEE WLAN Standard Roaming Bluetooth Security Authentication Protocols Wi-Fi Direct*
Encryption and Authentication Compliance US Government FIPS, FISMA Product Safety UL, C-UL, CB (IEC 60950-1) Model Numbers Models 9560NGW 9560D2W Frequency Modulation Frequency band 802.11ac wave 2, 2x2, Bluetooth* 5, PCIe, USB, M.2 2230 802.11ac wave 2, 2x2, Bluetooth* 5, PCIe, USB, M.2 1216 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) Modulation BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK Wireless Medium 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing (OFDM) Channels All channels as defined by the relevant specification and country rules. Spatial streams Intel Wireless-AC 9560: 2 X 2 Data Rates All data rates are theoretical maximums. 1.73 Gbps when using 160MHz channels Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Intel Tri-Band Wireless-AC 17265 (17265NGW/17265NGW LC) Form Factors M.2 Type 3030 Electrical interfaces M.2 Key 1-DP: 2xPCIe, USB, DP. Interface to Intel Wireless Gigabit-Antenna M10041 Module using X-FL, and one dedicated for Bluetooth X.FL; Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity 802.11ac, 802.11ad, 802.11abgn, 802.11a, 802.11d, 802.11e, 802.11i, 802.11h, 802.11w 0 to +80 degrees Celsius 60GHz
(802.11ad) 57GHz - 64GHz
(dependent on country) DPSK, BPSK, QPSK, 16 QAM, 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz
(dependent on country) 2.400 - 2.4835GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM CCK, DQPSK, DBPSK IEEE 802.11ac Data Rates IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Antenna Interface Connector IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation Frequency band Modulation IEEE 802.11ac Data Rates IEEE 802.11ad Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Cisco Compatible Extensions certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication Wireless Medium Channels DMG control PHY, DMG SC PHY 1, 2 and 3, subject to country rules 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) 2.4GHz ISM: Orthogonal Frequency Division Multiplexing
(OFDM) All channels as defined by the relevant specification and country rules. Spatial streams N/A Intel Tri-Band Wireless-AC 17265 Data Rates All data rates are theoretical maximums. Intel Tri-Band Wireless-AC 17265: Up to 867 Mbps 4620, 3850, 3080, 2503, 2310, 1925, 1540, 1251, 1155, 963, 770, 385 Mbps IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) Operating Systems Microsoft Windows 7*, Microsoft Windows 8.1* with connected standby Wi-Fi Alliance*
certification Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Architecture Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, AES-GCMP, TKIP WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Tri-Band Wireless-AC 17265 (17265NGW/17265NGW LC) Form Factors M.2 Type 3030 Electrical interfaces M.2 Key 1-DP: 2xPCIe, USB, DP. Interface to Intel Wireless Gigabit-Antenna M10041 Module using X-FL, and one dedicated for Bluetooth Antenna Interface Connector Antenna Diversity On-board diversity X.FL; Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 IEEE 802.11 Networking 802.11ac, 802.11ad, 802.11abgn, 802.11a, 802.11d, 802.11e, 802.11i, 802.11h, 802.11w Standards Operating Temperature Humidity Frequency Modulation Frequency band Modulation Wireless Medium Channels IEEE 802.11ac Data Rates IEEE 802.11ad Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General Cisco Compatible Extensions certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication 0 to +80 degrees Celsius 60GHz
(802.11ad) 57GHz - 64GHz
(dependent on country) DPSK, BPSK, QPSK, 16 QAM, DMG control PHY, DMG SC PHY 1, 2 and 3, subject to country rules 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz
(dependent on country) 2.400 - 2.4835GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) CCK, DQPSK, DBPSK 2.4GHz ISM: Orthogonal Frequency Division Multiplexing
(OFDM) All channels as defined by the relevant specification and country rules. Spatial streams N/A Intel Tri-Band Wireless-AC 17265 Data Rates All data rates are theoretical maximums. Intel Tri-Band Wireless-AC 17265: Up to 867 Mbps 4620, 3850, 3080, 2503, 2310, 1925, 1540, 1251, 1155, 963, 770, 385 Mbps IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) Operating Systems Microsoft Windows 7*, Microsoft Windows 8.1* with connected standby Wi-Fi Alliance*
certification Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Architecture Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions, v4.0 WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, AES-GCMP, TKIP WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Tri-Band Wireless-AC 18260 (18260NGW) Form Factors M.2 Type 2230 Electrical interfaces M.2 Key 1-DP: 2xPCIe, USB, DP. Interface to Intel Wireless Gigabit-Antenna M10041 or M10042 Module using X-FL (single coax cable to carry power, IF and control) Dimensions 22 mm x 30 mm x S3 [1.5mm Max (Top Side)/ 0.1mm max (bottom side)]
X.FL; Hirose U.FL-R-SMT mates with cable connector U.FL-LP-066 Antenna Diversity On-board diversity IEEE 802.11abgn, 802.11ac, 802.11ad, 802.11d, 802.11e, 802.11i, 802.11h, 802.11w Antenna Interface Connector IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation Frequency band Modulation Wireless Medium Channels IEEE 802.11ac Data Rates IEEE 802.11ad Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Bluetooth General 0 to +80 degrees Celsius 60GHz
(802.11ad) 57GHz - 64GHz
(dependent on country) DPSK, BPSK, QPSK, 16 QAM, DMG control PHY, DMG SC PHY 1, 2 and 3, subject to country rules 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 5.15GHz - 5.85GHz
(dependent on country) 2.400 - 2.4835GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) CCK, DQPSK, DBPSK 2.4GHz ISM: Orthogonal Frequency Division Multiplexing
(OFDM) All channels as defined by the relevant specification and country rules. Spatial streams N/A Intel Tri-Band Wireless-AC 18260 Data Rates All data rates are theoretical maximums. Intel Tri-Band Wireless-AC 18260: Up to 867 Mbps 4620, 3850, 3080, 2503, 2310, 1925, 1540, 1251, 1155, 963, 770, 385 Mbps IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Dual Mode Bluetooth* 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE), 4.1 Operating Systems Microsoft Windows 7*, Microsoft Windows 8.1* with connected standby Wi-Fi Alliance*
certification Wi-Fi CERTIFIED* for 802.11ac, a/b/g, n, WMM*, WPA*, WPA2*, and WPS, WPS 2.0, Protected Management Frames. Wi-Fi Direct* for peer-to-peer device connections. Architecture Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions Cisco Compatible Extensions, v4.0 certification Security Authentication Authentication Protocols Encryption Wi-Fi Direct*
Encryption and Authentication General Radio ON/OFF Control Connector interface Operating Temperature
(Adapter Shield) Humidity Non-
Operating Operating Systems Wi-Fi Alliance IEEE WLAN Standard Roaming Bluetooth Frequency Modulation Frequency band Modulation Wireless Medium Channels WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP, LEAP, EAP-FAST), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 64-bit and 128-bit WEP, AES-CCMP, AES-GCMP, TKIP WPA2, AES-CCMP Product Safety UL, C-UL, CB (IEC/EN 60950-1) Intel Tri-Band Wireless-AC 18265 (18265NGW) Dimensions (H x W x D) M.2 2230: 22 mm x 30 mm x 2.4 mm [1.5mm Max (Top Side)/ 0.1mm Max (Bottom Side)]
Weight M.2 2230: 2.4g Antenna Diversity Supported Supported M.2: PCIe, USB Interface to Intel Wireless Gigabit-Antenna M10101 Module using X-FL
(single coax cable to carry power, IF and control) 0 to +80 C 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Microsoft Windows 7*, Microsoft Windows 8.1*, Microsoft Windows 10, Linux* (limited feature support), Android Wi-Fi CERTIFIED* a/b/g/n/ac, WMM*, WMM-PS*, WPA*, WPA2*, WPS2, Protected Management Frames, Wi-Fi Direct* for peer to peer device connections, Wi-Fi Miracast as Source IEEE 802.11a/b/g/n/ac, 802.11d, 802.11e, 802.11h, 802.11i, 802.11w; 802.11r, 802.11k, 802.11v pending OS support; Fine Timing Measurement based on 802.11REVmc Supports seamless roaming between respective access points Dual Mode Bluetooth* 4.2, BLE 5GHz (802.11ac/n) 2.4GHz (802.11b/g/n) 60GHz
(802.11ad) 57GHz - 64GHz
(dependent on country) DPSK, BPSK, QPSK, 16 QAM, DMG control PHY, DMG SC PHY 1, 2 and 3, subject to country rules 5.15GHz - 5.85GHz
(dependent on country) 2.400 - 2.4835GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM 5GHz UNII: Orthogonal Frequency Division Multiplexing (OFDM) CCK, DQPSK, DBPSK 2.4GHz ISM: Orthogonal Frequency Division Multiplexing
(OFDM) All channels as defined by the relevant specification and country rules. Spatial streams N/A Intel Tri-Band Wireless-AC 18265 Data Rates All data rates are theoretical maximums. Up to 867 Mbps IEEE 802.11ac Data Rates IEEE 802.11ad Data Rates 4620, 3850, 3080, 2503, 2310, 1925, 1540, 1251, 1155, 963, 770, 385 Mbps IEEE 802.11n Data Rates Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps Authentication WPA and WPA2, 802.1X (EAP-TLS, TTLS, PEAP), EAP-SIM, EAP-AKA PAP, CHAP, TLS, GTC, MS-CHAP*, MS-CHAPv2 Encryption 64-bit and 128-bit WEP, AES-CCMP WPA2-PSK, AES-CCMP IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Security Authentication Protocols Wi-Fi Direct*
Encryption and Authentication Compliance Product Safety UL, C-UL, CB (IEC 60950-1) Intel Wireless Gigabit Sink W13100 Form Factors M.2 Type 3030 Antenna Interface Connector X.FL Antenna Diversity On-board diversity Electrical interfaces M.2 Key 1-DP: 2xPCIe, USB, DP. Interface to Intel Wireless Gigabit-Antenna M10041 Module using X-FL, and one dedicated for Bluetooth IEEE 802.11 Networking Standards 802.11ac, 802.11ad, 802.11abgn, 802.11a, 802.11d, 802.11e, 802.11i, 802.11h, 802.11w Operating Temperature 0 to +80 degrees Celsius Humidity Frequency Modulation 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 60GHz (802.11ad) Frequency band 57GHz - 64GHz (dependent on country) Modulation DPSK, BPSK, QPSK, 16 QAM, Wireless Medium DMG control PHY, DMG SC PHY Channels 1, 2 and 3, subject to country rules Spatial streams Intel Wireless Gigabit Sink W13100 Data Rates All data rates are theoretical maximums. IEEE 802.11ad Data Rates Over-the-Air Security 4620, 3850, 3080, 2503, 2310, 1925, 1540, 1251, 1155, 963, 770, 385 Mbps Authentication WPA2-Personal (WSC - WiFi Simple Configuration) Encryption 128-bit AES-GCMP Additional Crypto Functions Public Key Decrypt RSA-2048 General Operating Systems Microsoft Windows 7*, Microsoft Windows 8.1* with connected standby Architecture Infrastructure and SoftAP; Supports simultaneous Client and SoftAP modes Cisco Compatible Extensions certification Cisco Compatible Extensions, v4.0 Intel Wireless Gigabit 11000 Dimensions 20.5 mm x 14.2 mm x 1.8 mm (shield included) Soldered module has a proprietary land plan. Interface to Intel Wireless Gigabit Antenna-M 10042R using X-FL (single coax cable to carry power, IF and control) Weight Electrical interfaces 2 grams Antenna Interface Connector X.FL Antenna Diversity On-board diversity 802.11ad IEEE 802.11 Networking Standards Operating Temperature Humidity Frequency Modulation IEEE 802.11ad Data Rates Over-the-Air Security Encryption 128-bit AES-GCMP Additional Crypto Functions RSA-2048 Public Key Decrypt General Operating Systems 0 to +80 degrees Celsius 60GHz (802.11ad) 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Frequency band 57GHz - 64GHz (dependent on country) Modulation Channels DPSK, BPSK, QPSK, 16 QAM, 1, 2 and 3, subject to country rules Data Rates All data rates are theoretical maximums. 4620, 3850, 3080, 2503, 2310, 1925, 1540, 1251, 1155, 963, 770, 385 Mbps Authentication WPA2-Personal (WSC - WiFi Simple Configuration) Microsoft Windows 7*, Microsoft Windows 8.1* with connected standby, Microsoft Windows 10* with connected standby Intel Wireless Gigabit Sink W13110VR Dimensions (H x W x D) M.2 4230: 42 mm x 30 mm x 2.6 mm [1.5 mm Max (Top Side)/ 0.1 mm Max (Bottom Side)]
Weight Radio ON/OFF Control 5.16 grams Hardware Support Electrical interfaces M.2 Key G (User Defined). Interface to Intel Wireless Gigabit Antenna-M 10101 Module using X-FL (single coax cable to carry power, IF and control), up to 2 modules LEDs & GPIO Support Driving 2 LEDs or Multicolor LED with 4 states, Recovery button, Activity button with configurable action 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 4620, 3850, 3080, 2503, 2310, 1925, 1540, 1251, 1155, 963, 770, 385 Mbps Antenna Diversity On-board diversity 802.11ad IEEE 802.11 Networking Standards Operating Temperature
(Adapter Shield) Humidity Non-
Operating Frequency Modulation 0 to +80 degrees Celsius 60GHz (802.11ad) Frequency band 57GHz - 64GHz (dependent on country) Modulation Channels DPSK, BPSK, QPSK, 16 QAM, 1, 2 and 3, subject to country rules Data Rates All data rates are theoretical maximums. IEEE 802.11ad Data Rates Operating Systems None Wi-Fi Alliance*
certification N/A Over-the-Air Security Authentication WPA2-Personal (WSC - WiFi Simple Configuration) Encryption 128-bit AES-GCMP Additional Crypto Functions Public Key Decrypt RSA-2048 Intel Wireless Gigabit Antenna-M 10101R Module 7 mm x 19.3 mm x 1.8 mm Dimensions (H x W x D) Weight Antenna Connector Interface Operating Temperature
(Adapter Shield) Humidity Non-
Operating 1 gram X.FL 0 to +80 degrees Celsius Intel Wireless Gigabit 11100VR Dimensions (H x W x D) Weight 2 grams 20.5 mm x 14.2 mm x 1.8 mm (shield included) 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Supported in both hardware and software Soldered module has a proprietary land plan. Interface to Intel Wireless Gigabit Antenna-M 10042 Module using X-FL (single coax cable to carry power, IF and control) 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) 4620, 3850, 3080, 2503, 2310, 1925, 1540, 1251, 1155, 963, 770, 385 Mbps Radio ON/OFF Control Electrical interfaces LED Output IEEE 802.11 Networking Standards Operating Temperature
(Adapter Shield) Humidity Non-
Operating Frequency Modulation On/Off 802.11ad 0 to +80 degrees Celsius 60GHz (802.11ad) Frequency band 57GHz - 64GHz (dependent on country) Modulation Channels DPSK, BPSK, QPSK, 16 QAM, 1, 2 and 3, subject to country rules Data Rates All data rates are theoretical maximums. IEEE 802.11ad Data Rates Over-the-Air Security Operating Systems Microsoft Windows 10* with connected standby Authentication WPA2-Personal (WSC - WiFi Simple Configuration) Encryption 128-bit AES-GCMP Additional Crypto Functions Public Key Decrypt RSA-2048 Intel Wireless Gigabit Antenna-M 10042R Module 7.5 mm x 24.5 mm x 1.8 mm 1 gram X.FL 0 to +80 degrees Celsius Dimensions (H x W x D) Weight Antenna Connector Interface Operating Temperature
(Adapter Shield) Humidity Non-
Operating General Dimensions
(H x W x D) 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Intel Wi-Fi 6 AX201/ 14T90N (Models AX201NGW/AX201D2W/
AX201D2WL) M.2 2230: 22 mm x 30 mm x 2.4 mm [1.5 mm max (top side)/ 0.1 mm max (bottom side)]
M.2 1216: 12 mm x 16 mm x 1.65 (0.05) mm Weight M.2 2230: 2.33 (0.3) g M.2 1216: 0.61 (0.1) g Supported M.2: CNVio2 0 to +80 degrees Celsius Radio ON/OFF Control Connector Interface Operating Temperature Humidity Operating Systems Wi-Fi Alliance*
certification IEEE WLAN Standard Compliance US Government Product Safety Frequency Modulation Frequency band Modulation Wireless Medium Channels IEEE 802.11ax Data Rates IEEE 802.11ac Data Rates 50% to 90% RH non-condensing (at temperatures of 25 C to 35 C) Microsoft Windows 10*, Linux*, Chrome OS*
Wi-Fi CERTIFIED* a/b/g/n/ac with wave 2 features, WMM*, WMM-PS*, WPA*, WPA2*, WPS*, PMF*, Wi-Fi Direct*, Wi-Fi Miracast*, Wi-Fi Agile Multiband*, Wi-Fi Optimized Connectivity*, Wi-Fi Location*, Passpoint*, Wi-Fi Aware*, and Wi-Fi TimeSync*
IEEE 802.11-2016 and select amendments (selected feature coverage) IEEE 802.11a, b, g, n, ac, ax, d, e, h, i, k, r, u, v, w, ai; Fine Timing Measurement based on 802.11-2016 Bluetooth Security Bluetooth* 5 Authentication WPA* and WPA2* Personal and Enterprise; WPA3* (pending OS support) Authentication Protocols 802.1X EAP-TLS, EAP-TTLS/MSCHAPv2, PEAPv0/EAP-MSCHAPv2 (EAP-SIM, EAP-AKA, EAP-
AKA') Encryption 64-bit and 128-bit WEP, TKIP, 128-bit AES-CCMP, 256-bit AES-GCMP Regulatory For a list of country approvals, please contact your local Intel representatives. FIPS 140-2, FISMA UL, C-UL, CB (IEC 60950-1) Model Numbers Models Model AX201NGW Model AX201D2W Model AX201D2WL 802.11ax, 2x2, Bluetooth* 5, M.2 2230 802.11ax, 2x2, Bluetooth* 5, M.2 1216 802.11ax, 2x2, Bluetooth* 5, M.2 1216; LTE Coexistence 5GHz (802.11a/n/ac/ax) 2.4GHz (802.11b/g/n/ax) 5.15GHz - 5.85GHz (dependent on country) 2.400 - 2.4835GHz (dependent on country) BPSK, QPSK, 16 QAM, 64 QAM, 256 QAM, 1024 QAM CCK, DQPSK, DBPSK, 16 QAM, 64 QAM, 256 QAM, 1024 QAM 5GHz UNII: Orthogonal Frequency Division Multiple Access (OFDMA) 2.4GHz ISM: Orthogonal Frequency Division Multiple Access (OFDMA) All channels as defined by the relevant specification and country rules. Data Rates All data rates are theoretical maximums. Up to 2.4 Gbps Up to 867 Mbps Tx/Rx (Mbps): 300, 270, 243, 240, 216.7, 195, 180, 173.3, 150, 144, 135, 130, 120, 117, 115.5, 90, 86.667, 72.2, 65, 60, 57.8, 45, 43.3, 30, 28.9, 21.7, 15, 14.4, 7.2 54, 48, 36, 24, 18, 12, 9, 6 Mbps 54, 48, 36, 24, 18, 12, 9, 6 Mbps 11, 5.5, 2, 1 Mbps IEEE 802.11n Data Rates IEEE 802.11a Data Rates IEEE 802.11g Data Rates IEEE 802.11b Data Rates Back to Top Back to Contents Trademarks and Disclaimers Back to Contents Important Information Safety Information Third Party Software Notices Safety Information It is important that you read the safety information regarding your WiFi adapter. Please see the User's Guide for safety and regulatory notices. Third Party Software Notices Portions of Intel PROSet/Wireless WiFi Connection Utility include software under the following terms:
OpenSSL License Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-
core@openssl.org. 5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project. 6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com). Original SSLeay License Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved. This package is an SSL implementation written by Eric Young (eay@cryptsoft.com). The implementation was written so as to conform with Netscape's SSL. This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com). Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: "This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)"
The word 'cryptographic' can be left out if the routines from the library being used are not cryptographic related. 4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: "This product includes software written by Tim Hudson
(tjh@cryptsoft.com)"
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS:' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License.]
zlib.h -- interface of the 'zlib' general purpose compression library, version 1.2.3, July 18th, 2005 Copyright (C) 1995-2005 Jean-loup Gailly and Mark Adler This software is provided 'as-is', without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software. Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. 2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software. 3. This notice may not be removed or altered from any source distribution. Jean-loup Gailly jloup@gzip.org Mark Adler madler@alumni.caltech.edu Adapter Driver WPA Supplicant Portions of the driver include software under the following terms:
Copyright (c) 2003-2007, Jouni Malinen <jkmaline@cc.hut.fi> and contributors. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. Neither the name of Jouni Malinen nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Copyright (c) 2001, Dr Brian Gladman <brg@gladman.me.uk>, Worcester, UK. All rights reserved. The free distribution and use of this software in both source and binary form is allowed (with or without changes) provided that:
1. Distributions of this source code include the above copyright notice, this list of conditions and the following 2. distributions in binary form include the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other associated materials;
3. the copyright holder's name is not used to endorse products built using this software without specific written __________ LICENSE TERMS disclaimer;
permission. DISCLAIMER This software is provided 'as is' with no explicit or implied warranties in respect of its properties, including, but not limited to, correctness and fitness for purpose. Issue Date: 29/07/2002 This file contains the definitions required to use AES (Rijndael) in C. Portions Licensed from Devicescape Software, Inc. Intel PROSet/Wireless WiFi Connection Utility contains software licensed from Devicescape Software, Inc. Copyright
(c) 2004 - 2008 Devicescape Software, Inc. All rights reserved.
"Odd Button" Artistic License Portions of this software contain the standard version of "Odd Button" licensed under the Artistic License. The source code for "Odd Button" may be found online at http://sourceforge.net/projects/oddbutton. Back to Top Back to Contents Trademarks and Disclaimers Intel support is available online or by telephone. Available services include the most up-to-date product information, installation instructions about specific products, and troubleshooting tips. Back to Contents Customer Support Online Support Technical Support: http://www.intel.com/support Network Product Support: http://www.intel.com/network Corporate Web Site: http://www.intel.com Back to Top Back to Contents Trademarks and Disclaimers Back to Contents Warranty Information One-Year Limited Hardware Warranty Limited Warranty In this warranty statement, the term "Product" applies to the wireless adapters listed in Specifications. Intel warrants to the purchaser of the Product that the Product, if properly used and installed, will be free from defects in material and workmanship and will substantially conform to Intels publicly available specifications for the Product for a period of one (1) year beginning on the date the Product was purchased in its original sealed packaging. SOFTWARE OF ANY KIND DELIVERED WITH OR AS PART OF THE PRODUCT IS EXPRESSLY PROVIDED "AS IS", SPECIFICALLY EXCLUDING ALL OTHER WARRANTIES, EXPRESS, IMPLIED (INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE), provided however, that Intel warrants that the media on which the software is furnished will be free from defects for a period of ninety (90) days from the date of delivery. If such a defect appears within the warranty period, you may return the defective media to Intel for replacement or alternative delivery of the software at Intel's discretion and without charge. Intel does not warrant or assume responsibility for the accuracy or completeness of any information, text, graphics, links or other items contained within the software. If the Product which is the subject of this Limited Warranty fails during the warranty period for reasons covered by this Limited Warranty, Intel, at its option, will:
REPAIR the Product by means of hardware and/or software; OR REPLACE the Product with another product, OR, if Intel is unable to repair or replace the Product, REFUND the then-current Intel price for the Product at the time a claim for warranty service is made to Intel under this Limited Warranty. THIS LIMITED WARRANTY, AND ANY IMPLIED WARRANTIES THAT MAY EXIST UNDER APPLICABLE STATE, NATIONAL, PROVINCIAL OR LOCAL LAW, APPLY ONLY TO YOU AS THE ORIGINAL PURCHASER OF THE PRODUCT. Extent of Limited Warranty Intel does not warrant that the Product, whether purchased stand-alone or integrated with other products, including without limitation, semi-conductor components, will be free from design defects or errors known as "errata." Current characterized errata are available upon request. Further, this Limited Warranty does NOT cover: (i) any costs associated with the replacement or repair of the Product, including labor, installation or other costs incurred by you, and in particular, any costs relating to the removal or replacement of any Product soldered or otherwise permanently affixed to any printed circuit board or integrated with other products; (ii) damage to the Product due to external causes, including accident, problems with electrical power, abnormal, mechanical or environmental conditions, usage not in accordance with product instructions, misuse, neglect, accident, abuse, alteration, repair, improper or unauthorized installation or improper testing, or (iii) any Product which has been modified or operated outside of Intels publicly available specifications or where the original product identification markings (trademark or serial number) have been removed, altered or obliterated from the Product; or (iv) issues resulting from modification
(other than by Intel) of software products provided or included in the Product, (v) incorporation of software products, other than those software products provided or included in the Product by Intel, or (vi) failure to apply Intel-supplied modifications or corrections to any software provided with or included in the Product. How to Obtain Warranty Service To obtain warranty service for the Product, you may contact your original place of purchase in accordance with its instructions or you may contact Intel. To request warranty service from Intel, you must contact the Intel Customer Support ("ICS") center in your region (http://www.intel.com/support/wireless/) within the warranty period during normal business hours (local time), excluding holidays and return the Product to the designated ICS center. Please be prepared to provide: (1) your name, mailing address, email address, telephone numbers and, in the USA, valid credit card information; (2) proof of purchase; (3) model name and product identification number found on the Product; and (4) an explanation of the problem. The Customer Service Representative may need additional information from you depending on the nature of the problem. Upon ICS's verification that the Product is eligible for warranty service, you will be issued a Return Material Authorization ("RMA") number and provided with instructions for returning the Product to the designated ICS center. When you return the Product to the ICS center, you must include the RMA number on the outside of the package. Intel will not accept any returned Product without an RMA number, or that has an invalid RMA number, on the package. You must deliver the returned Product to the designated ICS center in the original or equivalent packaging, with shipping charges pre-paid (within the USA), and assume the risk of damage or loss during shipment. Intel may elect to repair or replace the Product with either a new or reconditioned Product or components, as Intel deems appropriate. The repaired or replaced product will be shipped to you at the expense of Intel within a reasonable period of time after receipt of the returned Product by ICS. The returned Product shall become Intels property on receipt by ICS. The replacement product is warranted under this written warranty and is subject to the same limitations of liability and exclusions for ninety (90) days or the remainder of the original warranty period, whichever is longer. If Intel replaces the Product, the Limited Warranty period for the replacement Product is not extended. WARRANTY LIMITATIONS AND EXCLUSIONS THIS WARRANTY REPLACES ALL OTHER WARRANTIES FOR THE PRODUCT AND INTEL DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, COURSE OF DEALING AND USAGE OF TRADE. Some states (or jurisdictions) do not allow the exclusion of implied warranties so this limitation may not apply to you. ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD. Some states (or jurisdictions) do not allow limitations on how long an implied warranty lasts, so this limitation may not apply to you. LIMITATIONS OF LIABILITY INTELS RESPONSIBILITY UNDER THIS OR ANY OTHER WARRANTY, IMPLIED OR EXPRESS, IS LIMITED TO REPAIR, REPLACEMENT OR REFUND, AS SET FORTH ABOVE. THESE REMEDIES ARE THE SOLE AND EXCLUSIVE REMEDIES FOR ANY BREACH OF WARRANTY. TO THE MAXIMUM EXTENT PERMITTED BY LAW, INTEL IS NOT RESPONSIBLE FOR ANY DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY (INCLUDING WITHOUT LIMITATION, LOST PROFITS, DOWNTIME, LOSS OF GOODWILL, DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY, AND ANY COSTS OF RECOVERING, REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH A SYSTEM CONTAINING THE PRODUCT), EVEN IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states (or jurisdictions) do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY BY STATE OR JURISDICTION. ANY AND ALL DISPUTES ARISING UNDER OR RELATED TO THIS LIMITED WARRANTY SHALL BE ADJUDICATED IN THE FOLLOWING FORUMS AND GOVERNED BY THE FOLLOWING LAWS: FOR THE UNITED STATES OF AMERICA, CANADA, NORTH AMERICA AND SOUTH AMERICA, THE FORUM SHALL BE SANTA CLARA, CALIFORNIA, USA AND THE APPLICABLE LAW SHALL BE THAT OF THE STATE OF DELAWARE. FOR THE ASIA PACIFIC REGION (EXCEPT FOR MAINLAND CHINA), THE FORUM SHALL BE SINGAPORE AND THE APPLICABLE LAW SHALL BE THAT OF SINGAPORE. FOR EUROPE AND THE REST OF THE WORLD, THE FORUM SHALL BE LONDON AND THE APPLICABLE LAW SHALL BE THAT OF ENGLAND AND WALES IN THE EVENT OF ANY CONFLICT BETWEEN THE ENGLISH LANGUAGE VERSION AND ANY OTHER TRANSLATED VERSION(S)OF THIS LIMITED WARRANTY (WITH THE EXCEPTION OF THE SIMPLIFIED CHINESE VERSION), THE ENGLISH LANGUAGE VERSION SHALL CONTROL. IMPORTANT! UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS SOLD HEREUNDER ARE NOT DESIGNED, OR INTENDED FOR USE IN ANY MEDICAL, LIFE SAVING OR LIFE SUSTAINING SYSTEMS, TRANSPORTATION SYSTEMS, NUCLEAR SYSTEMS, OR FOR ANY OTHER MISSION CRITICAL APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR. WEEE Back to Top Back to Contents Trademarks and Disclaimers Back to Contents Glossary Term 802.11 802.11a 802.11b 802.11g 802.11n 802.1X AAA Server AES-CCMP Available network BER Bit Rate BSSID Definition The 802.11 standard refers to a family of specifications developed by the IEEE for wireless LAN technology. The 802.11 specifies an over-the-air interface between a wireless client and a base station or between two wireless clients and provides 1 or 2 Mbps transmission in the 2.4 GHz band using either frequency hopping spread spectrum (FHSS) or direct sequence spread spectrum (DSSS). The 802.11a standard specifies a maximum data transfer rate of 54 Mbps and an operating frequency of 5 GHz. The 802.11a standard uses the Orthogonal Frequency Division Multiplexing (OFDM) transmission method. Additionally, the 802.11a standard supports 802.11 features such as WEP encryption for security. 802.11b is an extension to 802.11 that applies to wireless networks and provides 11 Mbps transmission (with a fallback to 5.5, 2 and 1 Mbps) in the 2.4 GHz band. 802.11b uses only DSSS. Throughput data rate 5+ Mbps in the 2.4 GHz band. The 802.11g standard specifies a maximum data transfer rate of 54 Mbps, an operating frequency of 2.4GHz, and WEP encryption for security. 802.11g networks are also referred to as Wi-Fi* networks. A task group of the IEEE 802.11 committee has defined a new draft specification that provides for increased throughput speeds of up to 540 Mbps. The specification provides for Multiple-Input-Multiple-Output (MIMO) technology, or using multiple receivers and multiple transmitters in both the client and access point, to achieve improved performance. 802.1X is the IEEE Standard for Port-Based Network Access Control. This is used in conjunction with EAP methods to provide access control to wired and wireless networks. Authentication, Authorization and Accounting Server. A system to control access to computer resources and track user activity. Access Point
(AP) A device that connects wireless devices to another network. For example, a wireless LAN, Internet modem or others. Ad Hoc Network A communication configuration in which every computer has the same capabilities, and any computer can initiate a communication session. Also known as a peer-to-peer network, a device to device network or a computer-to-computer network. Advanced Encryption Standard - Counter CBC-MAC Protocol is the new method for privacy protection of wireless transmissions specified in the IEEE 802.11i standard. AES-CCMP provides a stronger encryption method than TKIP. The AES algorithm is capable of using cryptographic keys of 128, 192, and 256 bits to encrypt and decrypt data in 128-bit blocks. AES-CCMP uses the AES block cipher, but restricts the key length to 128 bits. AES-CCMP incorporates two sophisticated cryptographic techniques (counter mode and CBC-MAC) to provide improved security between the mobile client and the access point. Authentication Verifies the identity of a user logging onto a network. Passwords, digital certificates, smart cards and biometrics are used to prove the identity of the client to the network. Passwords and digital certificates are also used to identify the network to the client. One of the networks listed under Available networks on the Wireless Networks tab of the Wireless Network Connection Properties (Windows* XP environment). Any wireless network that is broadcasting and is within receiving range of the WiFi adapter appears on the list. Bit Error Rate. The ratio of errors to the total number of bits being sent in a data transmission from one location to another. The total number of bits (ones and zeros) per second that a network connection can support. Note that this bit rate will vary, under software control, with different signal path conditions. Broadcast SSID Used to allow an access point to respond to clients on a wireless network by sending probes. A unique identifier for each wireless client on a wireless network. The Basic Service Set Identifier (BSSID) is the Ethernet MAC address of each adapter on the network. CCX (Cisco Compatible eXtension) Certificate CKIP DSSS EAP EAP-AKA EAP-GTC EAP-OTP EAP-SIM CA (Certificate Authority) A corporate certification authority implemented on a server. In addition, Internet Explorer's certificate can import a certificate from a file. A trusted CA certificate is stored in the root store. Cisco Compatible Extensions Program ensures that devices used on Cisco wireless LAN infrastructure meet the security, management and roaming requirements. Used for client authentication. A certificate is registered on the authentication server (for example, RADIUS server) and used by the authenticator. Cisco Key Integrity Protocol (CKIP) is a Cisco proprietary security protocol for encryption in 802.11 media. CKIP uses a key message integrity check and message sequence number to improve 802.11 security in infrastructure mode. CKIP is Cisco's version of TKIP. Client computer The computer that gets its Internet connection by sharing either the host computer's connection or the access point's connection. EAP-FAST EAP-FAST, like EAP-TTLS and PEAP, uses tunneling to protect traffic. The main difference is that EAP-FAST does not use certificates to authenticate. Direct Sequence Spread Spectrum. Technology used in radio transmission. Incompatible with FHSS. Short for Extensible Authentication Protocol, EAP sits inside of Point-to-Point Protocol's (PPP) authentication protocol and provides a generalized framework for several different authentication methods. EAP is supposed to head off proprietary authentication systems and let everything from passwords to challenge-response tokens and public-key infrastructure certificates all work smoothly. EAP-AKA (Extensible Authentication Protocol Method for UMTS Authentication and Key Agreement) is an EAP mechanism for authentication and session key distribution, using the Universal Mobile Telecommunications System (UMTS) Subscriber Identity Module (USIM). The USIM card is a special smart card used with cellular networks to validate a given user with the network. Provisioning in EAP-FAST is negotiated solely by the client as the first communication exchange when EAP-FAST is requested from the server. If the client does not have a pre-
shared secret Protected Access Credential (PAC), it can request to initiate a provisioning EAP-FAST exchange to dynamically obtain one from the server. EAP-FAST documents two methods to deliver the PAC: manual delivery through an out-of-
band secure mechanism, and automatic provisioning. Manual delivery mechanisms can be any delivery mechanism that the administrator of the network feels is sufficiently secure for their network. Automatic provisioning establishes an encrypted tunnel to protect the authentication of the client and the delivery of the PAC to the client. This mechanism, while not as secure as a manual method may be, is more secure than the authentication method used in LEAP. The EAP-FAST method can be divided into two parts: provisioning, and authentication. The provisioning phase involves the initial delivery of the PAC to the client. This phase only needs to be performed once per client and user. The EAP-GTC (Generic Token Card) is similar to the EAP-OTP except with hardware token cards. The request contains a displayable message, and the response contains the string read from the hardware token card. EAP-OTP (One-Time Password) is similar to MD5, except it uses the OTP as the response. The request contains a displayable message. The OTP method is defined in RFC 2289. Extensible Authentication Protocol-Subscriber Identity Module (EAP-SIM) authentication can be used with:
Network Authentication types: Open, Shared, and WPA*-Enterprise, WPA2*-
Enterprise. Data Encryption types: None, WEP and CKIP. A SIM card is a special smart card that is used by Global System for Mobile Communications
(GSM) based digital cellular networks. The SIM card is used to validate your credentials with the network A type of authentication method that uses EAP and a security protocol called the Transport Layer Security (TLS). EAP-TLS uses certificates that use passwords. EAP-TLS authentication supports dynamic WEP key management. A type of authentication method that uses EAP and Tunneled Transport Layer Security
(TTLS). EAP-TTLS uses a combination of certificates and another security method such as passwords. Scrambling data so that only the authorized recipient can read it. Usually a key is needed to interpret the data. Frequency-Hop Spread Spectrum. Technology used in radio transmission. Incompatible with DSSS. File and printer sharing A capability that allows a number of people to view, modify, and print the same file(s) from different computers. Fragmentation threshold The threshold at which the wireless adapter breaks the packet into multiple frames. This determines the packet size and affects the throughput of the transmission. A unit of frequency equal to 1,000,000,000 cycles per second. Host computer The computer that is directly connected to the Internet via a modem or network adapter. A wireless network centered around an access point. In this environment, the access point not only provides communication with the wired network, but also mediates wireless network traffic in the immediate neighborhood. Institute of Electrical and Electronics Engineers (IEEE) is an organization involved in defining computing and communications standards. The address of a computer that is attached to a network. Part of the address designates which network the computer is on, and the other part represents the host identification. A high-speed, low-error data network covering a relatively small geographic area. A version of Extensible Authentication Protocol (EAP). LEAP is a proprietary extensible authentication protocol developed by Cisco that provides a challenge-response authentication mechanism and dynamic key assignment. A hardwired address applied at the factory. It uniquely identifies network hardware, such as a wireless adapter, on a LAN or WAN. Transmission speed of 1,000,000 bits per second. EAP-TLS EAP-TTLS Encryption FHSS GHz
(Gigahertz) Infrastructure network IEEE Internet Protocol (IP) address LAN (Local Area Network) LEAP (Light Extensible Authentication Protocol) MAC (Media Access Control) Address Mbps
(Megabits-per-
second) MHz
(Megahertz) MS-CHAP A unit of frequency equal to 1,000,000 cycles per second. MIC (Michael) Message Integrity Check (commonly called Michael). An EAP mechanism used by the client. Microsoft Challenge Authentication Protocol (MS-
CHAP) Version 2, is used over an encrypted channel to enable server validation. The challenge and response packets are sent over a non-exposed TLS encrypted channel. ns(Nanosecond) 1 billionth (1/1,000,000,000) of a second. OFDM Orthogonal Frequency Division Multiplexing. Open authentication Allows any device network access. If encryption is not enabled on the network, any device that knows the Service Set Identifier (SSID) of the access point can gain access to the network. PEAP Peer-to-Peer mode Power save mode Preferred network RADIUS
(Remote Authentication Dial-In User Service) RF (Radio Frequency) Roaming RTS threshold SIM (Subscriber Identity Module) Silent mode SSID (Service Set Identifier) stealth Protected Extensible Authentication Protocol (PEAP) is an Internet Engineering Task Force
(IETF) draft protocol sponsored by Microsoft, Cisco, and RSA Security. PEAP creates an encrypted tunnel similar to the tunnel used in secure web pages (SSL). Inside the encrypted tunnel, a number of other EAP authentication methods can be used to perform client authentication. PEAP requires a TLS certificate on the RADIUS server, but unlike EAP-TLS there is no requirement to have a certificate on the client. PEAP has not been ratified by the IETF. The IETF is currently comparing PEAP and TTLS (Tunneled TLS) to determine an authentication standard for 802.1X authentication in 802.11 wireless systems. PEAP is an authentication type designed to take advantage of server-side EAP-Transport Layer Security
(EAP-TLS) and to support various authentication methods, including user passwords and one-time passwords, and Generic Token Cards. A wireless network structure that allows wireless clients to communicate directly with each other without using an access point. The state in which the radio is periodically powered down to conserve power. When the portable computer is in Power Save mode, received packets are stored in the access point until the wireless adapter wakes up. One of the networks that has been configured. Such networks are listed under Preferred networks on the Wireless Networks tab of the Wireless Network Connection Properties
(Windows* XP environment). RADIUS is an authentication and accounting system that verifies user's credentials and grants access to requested resources. The international unit for measuring frequency is Hertz (Hz), which is equivalent to the older unit of cycles per second. One MegaHertz (MHz) is one million Hertz. One GigaHertz (GHz) is one billion Hertz. For reference: the standard US electrical power frequency is 60 Hz, the AM broadcast radio frequency band is 0.55 -1.6 MHz, the FM broadcast radio frequency band is 88-108 MHz, and microwave ovens typically operate at 2.45 GHz. Movement of a wireless node between two micro cells. Roaming usually occurs in infrastructure networks built around multiple access points. Current wireless network roaming is only supported in the same subnet of a network. The number of frames in the data packet at or above which an RTS/CTS (request to send/clear to send) handshake is turned on before the packet is sent. The default value is 2347. Shared key An encryption key known only to the receiver and sender of data. This is also referred to as a pre-shared key. A SIM card is used to validate credentials with the network. A SIM card is a special smart card used by GSM-based digital cellular networks. Silent Mode Access Points or Wireless Routers have been configured to not broadcast the SSID for the wireless network. This makes it necessary to know the SSID in order to configure the wireless profile to connect to the access point or wireless router. Single Sign On Single Sign On feature set allows the 802.1X credentials to match your Windows log on user name and password credentials for wireless network connections. SSID or network name is a value that controls access to a wireless network. The SSID for your wireless network card must match the SSID for any access point that you want to connect with. If the value does not match, you are not granted access to the network. Each SSID may be up to 32 alphanumeric characters long and is case-sensitive. A stealth access point is one that has the capability and is configured to not broadcast its SSID. This is the WiFi network name that appears when a DMU (Device Management Utility, such as Intel PROSet/Wireless WiFi Connection Utility) scans for available wireless networks. Although this can enhance wireless network security, it is commonly considered a weak security feature. To connect to a stealth access point, a user must specifically know the SSID and configure their DMU accordingly. The feature is not a part of the 802.11 specification, and is known by differing names by various vendors: closed mode, private network, SSID broadcasting. Temporal Key Integrity protocol improves data encryption. Wi-Fi Protected Access* uses its TKIP. TKIP provides important data encryption enhancements including a re-keying method. TKIP is part of the IEEE 802.11i encryption standard for wireless networks. TKIP is the next generation of WEP, the Wired Equivalency Protocol, which is used to secure 802.11 wireless networks. TKIP provides per packet key mixing, a message integrity check and a re-keying mechanism, thus fixing the flaws of WEP. A type of authentication method using the Extensible Authentication Protocol (EAP) and a security protocol called the Transport Layer Security (TLS). EAP-TLS uses certificates which use passwords. EAP-TLS authentication supports dynamic WEP key management. The TLS protocol is intended to secure and authenticate communications across a public network through data encryption. The TLS Handshake Protocol allows the server and client to provide mutual authentication and to negotiate an encryption algorithm and cryptographic keys before data is transmitted. These settings define the protocol and the credentials used to authenticate a user. In TTLS, the client uses EAP-TLS to validate the server and create a TLS-encrypted channel between the client and server. The client can use another authentication protocol. Typically password-
based protocols challenge over this encrypted channel to enable server validation. The challenge and response packets are sent over a non-exposed TLS encrypted channel. TTLS implementations today support all methods defined by EAP, as well as several older methods
(CHAP, PAP, MS-CHAP and MS-CHAP-V2). TTLS can easily be extended to work with new protocols by defining new attributes to support new protocols. Wired Equivalent Privacy, 64- and 128-bit (64-bit is sometimes referred to as 40-bit). This is a low-level encryption technique designed to give the user about the same amount of privacy that he would expect from a LAN. WEP is a security protocol for wireless local area networks (WLANs) defined in the 802.11b standard. WEP is designed to provide the same level of security as that of a wired LAN. WEP aims to provide security by data over radio waves so that it is protected as it is transmitted from one end point to another. Either a pass phrase or hexadecimal key. The pass phrase must be 5 ASCII characters for 64-bit WEP or 13 ASCII characters for 128-
bit WEP. For pass phrases, 0-9, a-z, A-Z, and ~!@#$%^&*()_+|`-={}|[]\:";'<>?,./ are all valid characters. The hex key must be 10 hexadecimal characters (0-9, A-F) for 64-bit WEP or 26 hexadecimal characters (0-9, A-F) for 128-bit WEP. Is meant to be used generically when referring of any type to 802.11 network, whether 802.11b, 802.11a, or dual-band. WiMAX, the Worldwide Interoperability for Microwave Access, is a telecommunications technology aimed at providing wireless data over long distances in a variety of ways, from point-to-point links to full mobile cellular type access. It is based on the IEEE 802.16 standard. The name WiMAX was created by the WiMAX Forum, which was formed in June 2001 to promote conformance and interoperability of the standard. The forum describes WiMAX as "a standards-based technology enabling the delivery of last mile wireless broadband access as an alternative to cable and DSL."
A stand-alone wireless hub that allows any computer that has a wireless network adapter to communicate with another computer within the same network and to connect to the Internet. A type of local-area network that uses high-frequency radio waves rather than wires to communicate between nodes. TKIP (Temporal Key Integrity Protocol) TLS (Transport Layer Security) TTLS (Tunneled Transport Layer Security) WEP (Wired Equivalent Privacy) WEP Key Wi-Fi*
(Wireless Fidelity) WiMAX Wireless router WLAN (Wireless Local-Area Network) WPA* (Wi-Fi Protected Access) This is a security enhancement that strongly increases the level of data protection and access control to a wireless network. WPA is an interim standard that will be replaced with the IEEE's 802.11i standard upon its completion. WPA consists of RC4 and TKIP and provides support for BSS (Infrastructure) mode only. WPA and WPA2 are compatible. WPA2* (Wi-Fi This is the second generation of WPA that complies with the IEEE TGi specification. WPA2 Protected Access 2) consists of AES encryption, pre-authentication and PMKID caching. It provides support for BSS (Infrastructure) mode and IBSS (ad hoc) mode. WPA and WPA2 are compatible. WPA-Enterprise Wi-Fi Protected Access-Enterprise applies to corporate users. A new standards-based, interoperable security technology for wireless LAN (subset of IEEE 802.11i draft standard) that encrypts data sent over radio waves. WPA is a Wi-Fi standard that was designed to improve upon the security features of WEP as follows:
Improved data encryption through the temporal key integrity protocol (TKIP). TKIP uses a hashing algorithm to scramble the encryption keys and adds an integrity-
checking feature to ensure that the keys have not been tampered with. User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP regulates access to a wireless network based on a computer's hardware-specific MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized network users can access the network. WPA is an interim standard that will be replaced with the IEEE's 802.11i standard upon its completion. WPA-Personal Wi-Fi Protected Access-Personal provides a level of security in the small network or home environment. WPA-PSK (Wi-Fi Protected-
Access Pre-
Shared Key) WPA-PSK mode does not use an authentication server. It can be used with the data encryption types WEP or TKIP. WPA-PSK requires configuration of a pre-shared key (PSK). You must enter a pass phrase or 64 hex characters for a pre-shared key of length 256-bits. The data encryption key is derived from the PSK. Back to Top Back to Contents Trademarks and Disclaimers Label and compliance information FCC:
The host product must be labeled in a visible area with the following "
Contains FCC ID: BEJNT-14T90N". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ISED:
The final end product must be labeled in a visible area with the following: Contains transmitter module IC: 2703H-14T90N. Contient le module d'mission IC: 2703H-14T90N The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online.
This product uses the FCC Data API but is not endorsed or certified by the FCC