WPSM54G Wireless-G PrintServer W/ Multifunction User Manual

 

2.4802.11g GHz WIRELESS Wireless-G PrintServer with Multifunction Printer Support User Guide Model No. WPSM54G Wireless-G PrintServer with Multifunction Printer Support Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. This product contains chemicals, including lead, known WARNING:

to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. How to Use this User Guide The user guide to the Wireless-G PrintServer with Multifunction Printer Support has been designed to make understanding networking with the PrintServer easier than ever. Look for the following items when reading this User Guide:

This checkmark means there is a note of interest and is something you should pay special attention to while using the PrintServer. This exclamation point means there is a caution or warning and is something that could damage your property or the PrintServer. This question mark provides you with a reminder about something you might need to do while using the PrintServer. In addition to these symbols, there are definitions for technical terms that are presented like this:

word: definition. Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:

Figure 0-1: Sample Figure Description Figure numbers and descriptions can also be found in the List of Figures section. WPSM54G-UG-60801NC JL Wireless-G PrintServer with Multifunction Printer Support Table of Contents Chapter 1: Introduction Welcome Whats in this Guide?

Chapter 2: Getting to Know the PrintServer The Bottom Panel The Front Panel Chapter 3: Connecting the PrintServer Overview Connecting the PrintServer to Your Network Placement Options Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation Chapter 5: Windows Driver Installation Overview Installation Configuration of the PrintServer Driver Chapter 6: Configuring the PrintServer Using the Web-based Utility Overview The Setup Tab The Protocol Tab - TCP/IP The Protocol Tab - AppleTalk The Protocol Tab - NetBEUI The Protocol Tab - SNMP The Wireless Tab - Basic The Wireless Tab - Security The Printer Tab - Internet Printing The Printer Tab - Logical Port The Status Tab - Device The Status Tab - Printer The Status Tab - Wireless The Exit Tab 1 1 2 4 4 5 6 6 6 7 8 8 20 20 20 22 25 25 26 27 28 29 30 31 32 33 34 35 36 36 36 Wireless-G PrintServer with Multifunction Printer Support Chapter 7: Bi-Admin Management Overview Bi-Admin Installation Starting the Bi-Admin Management Utility The Bi-Admin Management Utility Chapter 8: Internet Printing Protocol (IPP) Overview Windows IPP Client Setup Appendix A: Troubleshooting Common Problems and Solutions Appendix B: Wireless Security Security Precautions Security Threats Facing Wireless Networks Appendix C: About Bi-Directional Printing Appendix D: Upgrading Firmware Appendix E: Windows Help Appendix F: Glossary Appendix G: Specifications Appendix H: Warranty Information Appendix I: Regulatory Information Appendix J: Contact Information 37 37 37 39 40 51 51 51 56 56 58 58 58 61 62 63 64 69 70 71 73 Wireless-G PrintServer with Multifunction Printer Support List of Figures Figure 2-1: PrintServers Bottom Panel Figure 2-2: PrintServers Front Panel Figure 3-1: Connect to the USB Port Figure 3-2: Connect to the Ethernet Port Figure 3-3: Desktop Placement Figure 4-1: Welcome Figure 4-2: Set up PrintServer Figure 4-3: Disconnect the USB Printer cable and power Figure 4-4: Connect the PrintServer to the Printer Figure 4-5: Connect the PrintServer Figure 4-6: Connect the PrintServer Figure 4-7: Reconnect the Printer Figure 4-8: Choose PrintServer Figure 4-9: Password Figure 4-10: Configure IP Settings Figure 4-11: Set PrintServer Password Figure 4-12: Select Wireless Network Figure 4-13: Configure Wireless Settings - SSID Figure 4-14: Select Wireless Network Figure 4-15: Wireless Security Settings - Disabled Figure 4-16: Wireless Security - WEP Figure 4-17: Wireless Security - WPA-Pre-Shared Figure 4-18: Confirm New Settings Figure 4-19: Disconnect power to the PrintServer Figure 4-20: Disconnect Network Figure 4-21: Reconnect the PrintServer Figure 4-22: PrintServer connection complete Figure 4-23: Continue to Set up Computer Figure 5-1: Welcome Figure 5-2: Set up Computer Figure 5-3: Select Printer 4 5 6 6 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 17 17 18 18 19 21 21 22 Wireless-G PrintServer with Multifunction Printer Support Figure 5-4: Check Print Driver Figure 5-5: Wireless-G PrintServer Diagnostic - Check Printer Driver Installation Figure 5-6: Printer Driver Not Installed Figure 5-7: Print Test Page Figure 5-8: PrintServer Diagnostic Icon Figure 5-9: PrintServer Info Figure 5-10: Right-click Icon Figure 6-1: Setup Tab Figure 6-2: Protocol Tab - TCP/IP Figure 6-3: Protocol Tab - AppleTalk Figure 6-4: Protocol Tab - NetBEUI Figure 6-5: Protocol Tab - SNMP Figure 6-6: Wireless Tab - Basic Figure 6-7: Wireless Tab - Security (WEP) Figure 6-8: Wireless Tab - Security (WPA) Figure 6-9: Printer - Internet Printing Figure 6-10: Printer - Logical Port Figure 6-11: Status Tab - Device Figure 6-12: Firmware Upgrade Figure 6-13: Status Tab - Printer Figure 6-14: Status Tab - Wireless Figure 6-15: Exit Figure 7-1: Welcome Figure 7-2: Bi-Admin Setup Welcome Figure 7-3: Choose Destination Location Figure 7-4: Select Program Folder Figure 7-5: Connected Protocol Figure 7-6: Searching for Device Figure 7-7: Bi-Admin Management Utility Figure 7-8: Device Information Figure 7-9: Printer Status Figure 7-10: Configuration - System Figure 7-11: Configuration - TCP/IP 22 23 23 23 24 24 24 26 27 28 29 30 31 32 32 33 34 35 35 36 36 36 37 37 38 38 39 39 40 40 41 42 43 Wireless-G PrintServer with Multifunction Printer Support Figure 7-12: Configuration - AppleTalk Figure 7-13: Configuration - NetBEUI Figure 7-14: Configuration - Internet Printing Figure 7-15: Configuration - Port Figure 7-16: Configuration - Wireless Figure 7-17: Configuration - SNMP Figure 7-18: Upgrade Figure 7-19: Detected LAN Cards Figure 7-20: BIN File Information Figure 7-21: Add Cross Segment PrintServer Figure 8-1: Windows XP - Local or Network Printer Figure 8-2: Windows XP - Specify a Printer Figure 8-3: Windows 2000 - Locate Your Printer Figure D-1: Status Tab - Device Figure D-2: Firmware Upgrade 44 45 46 47 48 49 50 50 50 50 53 54 54 62 62 Wireless-G PrintServer with Multifunction Printer Support Chapter 1: Introduction Welcome Thank you for choosing the Linksys Wireless-G PrintServer with Multifunction Printer Support. The PrintServer lets you connect a USB printer directly to your network, eliminating the need to dedicate a PC to print sharing chores. Using a PrintServer frees up your print share PC so you dont have to leave it on all the time. It also removes the printing bottleneck, and sets your PC free to do more useful work. The USB port is compatible with USB 1.1 printers, as well as printers that support the new high-speed USB 2.0 specification for even faster throughput. How does the PrintServer do all of this? A print server is a device that allows multiple computers to share a printer over a network. You can connect the PrintServer directly to your network using an Ethernet network cable, or you can connect the PrintServer over Wireless-G (802.11g) at up to 54Mbps. The wireless option lets you put your printer wherever you want to, without having to run a cable. Whichever way the PrintServer is attached to your network, both your wireless and wired PCs will have access to it and its USB printer. But what does all of this mean?

Networks are useful tools for sharing Internet access and computer resources. Multiple computers can share Internet access, so you dont need more than one high-speed Internet connection. Using the PrintServer, you can access one printer from different computers. Plus, you can access data located on another computers hard drive and play multi-player video games. So, networks not only are useful in homes and offices, but also can be fun. PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is why the network is called wired. PCs equipped with wireless cards or adapters can communicate without cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a wireless network. This is sometimes called a WLAN, or Wireless Local Area Network. Your network router bridges wireless networks of both 802.11b and 802.11g standards and wired networks, allowing them to communicate with each other. To guide you through the process of installing the PrintServer, run the Setup Wizard on the Setup CD-ROM (you can use the instructions in the Quick Installation or User Guide to help you). After you have installed the PrintServer, you can change its settings using its browser-based utility, which is described in this User Guide. These instructions should be all you need to get the most out of the Wireless-G PrintServer. Chapter 1: Introduction Welcome mbps: one million bits per second; a unit of measurement for data transmission lan (local area network): the computers and networking products that make up the network in your home or office ethernet: an IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium 802.11b: an IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz 802.11g: an IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices browser: an application program that provides a way to look at and interact with all the information on the World Wide Web 1 Wireless-G PrintServer with Multifunction Printer Support Whats in this Guide?

This user guide covers the steps for setting up and using the PrintServer.

Chapter 1: Introduction This chapter describes the PrintServers applications and this User Guide.

Chapter 2: Getting to Know the PrintServer This chapter describes the physical features of the PrintServer.

Chapter 3: Connecting the PrintServer This chapter instructs you on how to connect the PrintServer to your network.

Chapter 4: Configuring the PrintServer using the Setup Wizard This chapter instructs you on how to use the Setup Wizard to install your PrintServer.

Chapter 5: Windows Driver Installation This chapter explains how to install the Windows driver for the PrintServer.

Chapter 6: Configuring the PrintServer Using the Web-based Utility This chapter explains use the web-based utility to change the PrintServers settings.

Chapter 7: Bi-Admin Management This chapter explains how to use the Bi-Admin Management utility, which is for advanced users only.

Chapter 8: Internet Printing Protocol (IPP) This chapter instruct you on how to use the PrintServer as an IPP server so you can run remote print jobs.

Appendix A: Troubleshooting This appendix describes some potential problems and solutions regarding use of the PrintServer.

Appendix B: Wireless Security This appendix explains the security risks in wireless networking and how you can help protect your network

Appendix C: About Bi-Directional Printing This appendix describes bi-directional printing.

Appendix D: Upgrading Firmware This appendix instructs you on how to upgrade the firmware on the PrintServer should you need to do so. Chapter 1: Introduction Whats in this Guide?

2 Wireless-G PrintServer with Multifunction Printer Support

Appendix E: Windows Help This appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.

Appendix F: Glossary This appendix gives a brief glossary of terms frequently used in networking.

Appendix G: Specifications This appendix provides the technical specifications for the PrintServer.

Appendix H: Warranty Information This appendix supplies the warranty information for the PrintServer.

Appendix I: Regulatory Information This appendix supplies the regulatory information regarding the PrintServer.

Appendix J: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support. Chapter 1: Introduction Whats in this Guide?

3 Wireless-G PrintServer with Multifunction Printer Support Chapter 2: Getting to Know the PrintServer The Bottom Panel The PrintServers ports and Reset button are located on the bottom panel. Power Ethernet Figure 2-1: PrintServers Bottom Panel The Power port is where you will connect the power adapter. The Ethernet port is where you will connect the PrintServer to your wired network. (This is optional.) USB Printer The USB Printer port is where you will connect the USB printer to the PrintServer. The USB icon (right) designates a USB port. The PrintServer comes with a USB cable. One end has a rectangular connector called Type A. The other end has a square connector called Type B. The USB cables Type A end connects to the PrintServer, and the Type B end connects to the printer. USB Connector-Type A USB Connector-Type B Reset Button Use the Reset Button to reset the PrintServer to its factory defaults or print a test page. The instructions are provided on the right side of this page. Chapter 2: Getting to Know the PrintServer The Bottom Panel IMPORTANT: Resetting the PrintServer will delete all of your settings and replace them with the factory defaults. Do not reset the PrintServer if you want to retain the settings. To reset the factory default settings 1. Unplug the PrintServer. 2. Press and hold the Reset button. While pressing the 3. button, plug in the PrintServer. If you continue pressing the button for 10 seconds, the PrintServer will be reset to factory defaults. To generate a diagnostic print-out 1. Ensure that both the PrintServer and the printer attached to the Printer port are ON. 2. Press the Reset button, and hold it in for 2 seconds. 3. The test page, which lists the current settings, will be printed. PostScript printers are unable to print this page. If you have a PostScript printer on the USB Printer port, the test page will not be printed. 4 Wireless-G PrintServer with Multifunction Printer Support The Front Panel The PrintServers LEDs are located on the front panel. Figure 2-2: PrintServers Front Panel USB Wireless Ethernet Power Green/Orange. The USB LED lights up green when there is a printer connected to the USB port. The LED flashes green when the PrintServer is sending data through the USB port. It lights up orange when there is a problem with the USB printer. Green. The Wireless LED serves two purposes. If the LED is continuously lit, the PrintServer is successfully connected to the wireless network. If the LED is flashing, the PrintServer is actively sending or receiving data from the wireless network. Green/Orange. If the Ethernet LED is continuously lit green, the PrintServer is successfully connected to a device through the Ethernet port. The LED flashes green when the PrintServer is actively sending or receiving data from the wired network. It flashes orange when there are collisions detected on the Ethernet port. Green/Orange. If the Power LED is continuously lit green, then the PrintServer is ready for use. The LED flashes green when the PrintServer is booting up, a system self-test is running, or the firmware is being upgraded. It lights up orange when there is an error. Chapter 2: Getting to Know the PrintServer The Front Panel 5 Wireless-G PrintServer with Multifunction Printer Support Chapter 3: Connecting the PrintServer Overview Before starting the physical installation, note the PrintServers default name, which starts with LK (for example, LK71107). The default name is shown in the Server field on the PrintServers sticker, which is located on the PrintServers back panel. During the PrintServer driver installation, this name is used to identify the PrintServer you are currently installing. Connecting the PrintServer to Your Network 1. Use the USB cable to connect your USB printer to the PrintServers USB Printer port. Plug the Type A connector end into the PrintServer and the Type B connector end into the printer. 2. If you are connecting the PrintServer to your wired network, then plug one end of the Ethernet network cable into the PrintServers Ethernet port. Then connect the other end of the cable to your router or switch. The distance between the PrintServer and the other device should not exceed 328 feet (100 meters). Figure 3-1: Connect to the USB Port 3. Power on your printer. 4. Plug the power adapter into the PrintServers Power port. Then plug the other end into an electrical outlet. IMPORTANT: Make sure you use the power adapter supplied with the PrintServer. Use of a different power adapter could damage the PrintServer. NOTE: The PrintServer does not have an on/off power switch. Whenever its power adapter is plugged into a power supply, the PrintServer is powered on. The PrintServer can be powered on before, during, or after your network is powered on. Proceed to the next section, Placement Options. Figure 3-2: Connect to the Ethernet Port Chapter 3: Connecting the PrintServer Overview 6 Wireless-G PrintServer with Multifunction Printer Support Placement Options There are different ways to place the PrintServer. The first way is to place the PrintServer horizontally on a surface, so it sits on four small rubber pads. You can also use the included velcro to mount the PrintServer on a wall or underneath a shelf. To use the velcro, follow these instructions:

1. Separate the included velcro into its two sides, the hook side and the loop side. You will use the tape on the backs of the velcro sides to attach them to the PrintServer and surface you want to use. 2. For the first velcro side, peel off the cover protecting the tape, and attach it to the recessed area on the back panel of the PrintServer. 3. For the other velcro side, peel off the cover, and attach it to the location you have chosen for the PrintServer. 4. Attach the velcro sides to each other, and make sure the PrintServer is securely mounted on the wall or underneath the shelf. 5. Adjust the position of the antenna so that it is positioned as high as possible. Usually, the higher you place the antenna, the better the performance and range will be. The physical installation of the Wireless-G PrintServer with Multifunction Printer Support is complete. Proceed to Chapter 4: Configuring the PrintServer Using the Setup Wizard. Figure 3-3: Desktop Placement Chapter 3: Connecting the PrintServer Placement Options 7 Wireless-G PrintServer with Multifunction Printer Support Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation To install the PrintServer, you will use the Setup CD-ROM to run the Setup Wizard. It is highly recommended that you use a computer on the wired network to set up the PrintServer. However, if you only have a wireless network, then you can use a computer on the wireless network to set up the PrintServer. 1. Insert the Setup CD-ROM into the computers CD-ROM drive. The Setup Wizard should run automatically. If it does not, click the Start button and choose Run. In the box that appears, enter D:\setupWizard.exe (if D is the letter of your CD-ROM drive). 2. When you see the Welcome screen, click Setup Wizard to continue. Click Exit to end the installation. Click User Guide button to view the User Guide. 3. If this is the first time you have installed the PrintServer, click Set up PrintServer. If you have already installed and configured the PrintServer, click Set up Computer and proceed to Chapter 5: Windows Driver Installation. Figure 4-1: Welcome Figure 4-2: Set up PrintServer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 8 Wireless-G PrintServer with Multifunction Printer Support 4. You will need to first disconnect the USB Printer cable from the computer and disconnect the power from the printer. Click Next when finished. Figure 4-3: Disconnect the USB Printer cable and power 5. In Step 2, you will connect the USB printer cable to the USB port on the Print Server. Click Next. Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 9 Figure 4-4: Connect the PrintServer to the Printer Wireless-G PrintServer with Multifunction Printer Support 6. From the Connecting Your PrintServer screen, you will connect your Ethernet port. The Ethernet connection is for configuration purposes only. Later in this installation, you will need to disconnect the ethernet cable and reconnect your PrintServer, printer, and router. Click Next to continue. Click Back to return to the previous screen. 7. Connect the Power Adapter to the PrintServer and click Next. Figure 4-5: Connect the PrintServer Figure 4-6: Connect the PrintServer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 10 Wireless-G PrintServer with Multifunction Printer Support 8. Reconnect the power adapter to the printer. Plug the power into the wall outlet. Click Next to continue, or click Back to return to the previous screen. Wait a few moments while the system searches for the PrintServer. 9. Select the proper PrintServer. If you can not find the PrintServer, click Refresh. Click Next. Figure 4-7: Reconnect the Printer Figure 4-8: Choose PrintServer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 11 Wireless-G PrintServer with Multifunction Printer Support 10. If you have changed the default password previously, the password dialog opens and you are prompted for your password. Otherwise, the installation will continue. If you have forgotten your password, hold the reset button on the side of the PrintServer for 10 seconds. This will reset the device to factory default. The default password is admin. 11. The Configure IP Settings screen appears. If your network uses a router with a DHCP setting that automatically assigns IP addresses, select Automatically obtain an IP address (DHCP). If your network uses a static IP address, select Set IP configuration manually, and enter the IP Address, Subnet Mask, and Gateway in the fields provided. Click Next to continue, or click Back to return to the previous screen. Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation Figure 4-9: Password Figure 4-10: Configure IP Settings ip (internet protocol): a protocol used to send data over a network ip address: the address used to identify a computer or device on a network static ip address: a fixed address assigned to a computer or device connected to a network. 12 Wireless-G PrintServer with Multifunction Printer Support 12. The Set PrintServers Password screen appears. If you want to change your password, enter your current password in the Password field. Enter the new password in the Confirm field. Click Next to continue, or click Back to return to the previous screen. Figure 4-11: Set PrintServer Password 13. Locate and select the wireless network you want to connect to. If you do not see the wireless network you wish to use, click Refresh and locate the network. Click Next to continue, or click Back to return to the previous screen. Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 13 Figure 4-12: Select Wireless Network Wireless-G PrintServer with Multifunction Printer Support 14. If you clicked Manual Setup, the Configure Wireless Settings screen appears with the SSID field. Enter your wireless networks SSID or name. This is the unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have 32 characters or fewer. Click Next to continue, or click Back to return to the previous screen. Figure 4-13: Configure Wireless Settings - SSID If you click Refresh and select the network, the setup wizard automatically detects what kind of security network your computer has. Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 14 Figure 4-14: Select Wireless Network Wireless-G PrintServer with Multifunction Printer Support 15. If your network uses wireless security, you will prompted to enter the correct information. Figure 4-15: Wireless Security Settings - Disabled If you enter a Passphrase, you will see the automatically generated WEP key on the following screen. Otherwise, enter the WEP key manually in the field provided. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are 0-9 and A-F. Click Next to continue, or click Back to return to the previous screen. Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 15 Figure 4-16: Wireless Security - WEP Wireless-G PrintServer with Multifunction Printer Support WPA-Pre-Shared Key Enter a Pre-Shared Key that is 8-63 characters in length. Click Next to continue, or click Back to return to the previous screen. Figure 4-17: Wireless Security - WPA-Pre-Shared 16. The Confirmation screen will appear. Your old and new settings will be displayed. If you want to save the new settings, click Next. If you want to make a change, click Back to make changes. Please wait a few moments while the system changes the PrintServers settings. NOTE: In the next few screens, you will need to disconnect and reconnect your PrintServer. Proceed in the order specified to avoid any networking conflicts. Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 16 Figure 4-18: Confirm New Settings Wireless-G PrintServer with Multifunction Printer Support 17. Disconnect the power to the PrintServer. Click Next. 18. Disconnect the Network Cable from the PrintServer and router. Figure 4-19: Disconnect power to the PrintServer Figure 4-20: Disconnect Network Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 17 Wireless-G PrintServer with Multifunction Printer Support 19. Reconnect the power to the PrintServer and click Next. Wait a few moments while the system checks for the network. Figure 4-21: Reconnect the PrintServer 20. The PrintServer is now connected to your wireless network properly. The order used in reconnecting your PrintServer, router, and printer is very important. If you may have reconnected improperly, please click Back and review your processes. Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 18 Figure 4-22: PrintServer connection complete Wireless-G PrintServer with Multifunction Printer Support 21. Now you have finished the initial setup.. You will need to install the driver next. Click Set up Computer at the bottom of this, and go to Chapter 5:

Windows Driver Installation of this user guide. Figure 4-23: Continue to Set up Computer Chapter 4: Configuring the PrintServer Using the Setup Wizard Installation 19 Wireless-G PrintServer with Multifunction Printer Support Chapter 5: Windows Driver Installation Overview This section installs the PrintServers software on your Windows 98, Me, 2000, or XP computers so they can use the PrintServer for print jobs. (The PrintServer is fully compatible with Windows 98, Me, 2000, and XP.) At this point, you must have the following:

the PrintServer hardware installed on your network. If not, see Chapter 3: Connecting the PrintServer.

TCP/IP installed on each of your computers.

an IP address assigned to each of the computers on your network.

an IP address assigned to the PrintServer by you or your network router. By default the PrintServer has DHCP enabled so the network router will automatically assign an IP address. If you need to manually assign an IP address, run the Setup Wizard on the Setup CD-ROM or go to Chapter 7: Bi-Admin Management. It is assumed that your CD-ROM drives letter name is designated as D. If your CD-ROM drive is named another letter, replace all instances of D with the appropriate letter. If you need to install the PrintServers driver on computers without a CD-ROM drive, you can create a setup disk by using a computer with a CD-ROM drive to copy the contents of D:\Driver\PTP onto a floppy disk. Installation 1. Make sure you have no programs or applications running on your computer. 2. If you havent already done so, insert the Setup CD-ROM into the computers CD-ROM drive. The Setup CD-

ROM should run automatically. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setupWizard.exe (if D is the letter of your CD-ROM drive). HAVE YOU: already set up your printer? Linksys recommends that you set up your printer and install your printers driver before you install the PrintServers driver. Chapter 5: Windows Driver Installation Overview 20 Wireless-G PrintServer with Multifunction Printer Support 3. When you see the Welcome screen, click Click Here to Start to continue. Click Exit to end the installation. 4. Click Set up Computer. Figure 5-1: Welcome Configuration of the PrintServer Driver Chapter 5: Windows Driver Installation Installation Figure 5-2: Set up Computer 21 Wireless-G PrintServer with Multifunction Printer Support Configuration of the PrintServer Driver 1. The Wireless-G PrintServer Driver screen automatically appears. Select the PrintServer you are installing. Then click Next. NOTE: If the PrintServer is not listed, then click Refresh. If the PrintServer cannot be found, then select to temporarily disable the firewall and click Refresh again. 2. The Checking Printer Driver screen appears. Select the driver for your printer, and click Next to continue. Figure 5-3: Select Printer If the driver for your printer is not installed, you will see a new window pop up. The message will ask you to exit the Wizard and install the driver for your printer. Click OK and install the driver. After the driver has been installed, run the Setup Wizard and click Driver Install on the Welcome screen. Figure 5-4: Check Print Driver Chapter 5: Windows Driver Installation Configuration of the PrintServer Driver 22 Wireless-G PrintServer with Multifunction Printer Support 3. The Wireless-G PrintServer Driver screen appears. Review the PrintServer status and then click Next. 4. The Wireless-G PrintServer Driver screen appears. If you want to print a test page, click Test Print. Then click Finish. Figure 5-5: Wireless-G PrintServer Diagnostic - Check Printer Driver Installation 5. If youve chosen to print a test page, the test page dialog appears. Click OK. Chapter 5: Windows Driver Installation Configuration of the PrintServer Driver Figure 5-6: Printer Driver Not Installed Figure 5-7: Print Test Page 23 Wireless-G PrintServer with Multifunction Printer Support 6. The Print Server diagnostic icon will appear in the system tray of your desktop. When you double-click the icon, you will see the PrintServer Info screen. If you want to run the wizard that configures the printer driver, click the Diagnostics button. To close the PrintServer Info screen, click the Close button. When you right-click the Print Server diagnostic icon, you will see a menu. To see the version number of the Print Server Utility, click About. To see the PrintServer Info screen, click Info. To close the Utility, click Exit. The driver installation and configuration is complete. You can now use the PrintServer. If you would like to change the PrintServers settings, use the PrintServers web-based utility. For more information, refer to Chapter 6: Configuring the PrintServer Using the Web-based Utility. Figure 5-8: PrintServer Diagnostic Icon Figure 5-9: PrintServer Info Figure 5-10: Right-click Icon Chapter 5: Windows Driver Installation Configuration of the PrintServer Driver 24 Wireless-G PrintServer with Multifunction Printer Support Chapter 6: Configuring the PrintServer Using the Web-based Utility Overview After setting up the PrintServer with the Setup Wizard, the PrintServer will be ready for use. However, if youd like to change its settings, use the PrintServers web-based utility. This chapter will describe each web page of the utility and each pages key functions. The utility can be accessed via your web browser through the use of a networked computer. There are six main tabs: Setup, Protocol, Wireless, Printer, Status, and Exit. Additional tabs will be available after you click one of the main tabs, except for the Setup tab. To access the web-based utility, launch Internet Explorer or Netscape Navigator, and enter the PrintServers IP address in the Address field. Then press Enter. NOTE: Use the PrintServers IP address that you noted when you ran the Setup Wizard. Otherwise, insert the Setup CD-ROM, and when the Welcome screen appears, click Setup Wizard. Follow the instructions until you reach the Wireless-G PrintServer Setup screen. Note the IP address, and then click Back until you reach the Welcome screen. Click Exit. Chapter 6: Configuring the PrintServer Using the Web-based Utility Overview 25 Wireless-G PrintServer with Multifunction Printer Support The Setup Tab The first screen that appears is the Setup tab and allows you to change the PrintServers general settings. WPS54G Device Name Enter the PrintServers name in the field provided. The name is located on a sticker on the bottom of the PrintServer. Password Current Password. To change the PrintServers password, enter the current password in the Current Password field. Figure 6-1: Setup Tab New Password and Verify Password. Enter the new password in the New Password field, and then enter the new password again in the Verify Password field. Protocols The TCP/IP protocol is enabled by default. Enable: Apple Talk or NetBEUI. Check the box(es) for AppleTalk or NetBEUI, if they are used by your network. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Setup Tab 26 Wireless-G PrintServer with Multifunction Printer Support The Protocol Tab - TCP/IP Click the TCP/IP tab to view or change the TCP/IP values of the PrintServer. IP Address Obtain an IP Address Automatically. If your network router is using DHCP to assign IP addresses, select Obtain an IP Address Automatically. By default, Obtain an IP Address Automatically is enabled. Use the Following IP Address. If you need to assign the PrintServer a fixed IP address (also known as static IP address), select Use the Following IP Address, and enter the appropriate values under IP Address, Subnet Mask, and Gateway. Make sure the IP Address and Subnet Mask are appropriate for your network. If you change the PrintServers IP address, make sure you that you reconnect to the PrintServer using that new IP address. Otherwise, you will not be communicating with the PrintServer. In most cases, the Gateway IP address is the IP address of your router, and you should complete the Gateway field if you will use the PrintServer for Internet printing. (To find out your routers IP address, consult your routers documentation.) Connection Delay before reconnection attempt. Set how long you want the PrintServer to wait between attempts. Number of reconnection attempts. Specify the number of times that the PrintServer will attempt to connect to the network. Click the Save button to apply your changes, or click Cancel to cancel your changes. Figure 6-2: Protocol Tab - TCP/IP Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - TCP/IP 27 Wireless-G PrintServer with Multifunction Printer Support The Protocol Tab - AppleTalk AppleTalk is a network communications protocol that allows computers to talk to each other using Ethernet. Typically only Macintoshes use AppleTalk, although other platforms can use it if they have the necessary, third-

party software. Communication Printer Object Type. The Printer Object Type can be obtained from the manufacturer of the printer. Enter the type of printer in the field provided. For each printer connected to the PrintServer, you will choose the Communications Protocol that allows the devices on the network to communicate. Communication Protocol. Select the type of Communication Protocol you will use, ASCII or Binary for each printer, according to the recommendation of the printers manufacturer. For more information, refer to the printers documentation. Click the Save button to apply your changes, or click Cancel to cancel your changes. Figure 6-3: Protocol Tab - AppleTalk Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - AppleTalk 28 Wireless-G PrintServer with Multifunction Printer Support The Protocol Tab - NetBEUI NetBEUI connection settings of the PrintServer are available on this tab. Domain Name Enter the name of the domain that you want the PrintServer associated with in the Domain Name field. If you are unsure of the Domain Name, you can find it out by looking on any computer already on the network. In Windows 98, right-click Network Neighborhood and select Properties. Under the Identification tab, there will be listed that computers name, and the Domain to which it is connected. For Windows Me, 2000, or XP, right-click My Network Places. In Windows Me, choose Properties from the menu that appears. In Windows 2000 or XP, choose Properties from the menu that appears. Then, right-click Local Area Connection and choose Properties. The Domain name will appear. If you want the PrintServer to be connected to that same Domain, enter that Domain name here. If no Domain name exists there, you will use the Workgroup name from that window. Options Response Time. You can specify the Response Time that you prefer for the PrintServer. This is the amount of time

(measured in seconds) that the PrintServer will wait for a response from the network before timing out. Abort Print Job if Error. You also have the option to use this feature, Abort Print Job if Error. Selecting Yes here will terminate the printing if there is an error of any kind. If you select No, print jobs that have errors will be sent to the printer, but might not print properly. Click the Save button to apply your changes, or click Cancel to cancel your changes. Figure 6-4: Protocol Tab - NetBEUI Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - NetBEUI 29 Wireless-G PrintServer with Multifunction Printer Support The Protocol Tab - SNMP Use this screen to view or change the PrintServers SNMP (Simple Network Management Protocol) settings. The PrintServer supports SNMP, which allows network administrators to monitor and control the PrintServer through the use of network management platforms, such as HP OpenView. The appropriate MIB file must be imported into your SNMP management program using the Import-Compile command. Check your programs documentation for details on this procedure. The MIB file is named Mib2p.mib and is provided in the MiB folder on the Setup CD-ROM. General SysContact. Enter the name of the contact person in the SysContact field. SysLocation. Enter the location of the contact person in the SysLocation field. Management Stations Station No. Select the number of the management station from the Station No. drop-down menu (1-4). Click the Get Data button to display the information for the selected station. IP Address. Enter the IP address of the management station running the SNMP program. Community. Enter the name of the SNMP community, which is usually public or private. Access. Select the level of access for this management station, Not Accessible, Read-only, or Read/Write. Trap Receivers Receiver No. Select the number of the trap receiver from the Receiver No. drop-down menu (1-4). Click the Get Data button to display the information for the selected trap receiver. IP Address. Enter the IP address of the trap receiver that will be sent the trap messages or notifications. Community. In the Community field, enter the name of the SNMP community, which is usually public or private. Enable with Severity level. To designate a severity level, click the checkbox next to Enable with Severity level. From the following drop-down menu, select the desired level of severity, with 1 meaning least severe. Click the Save button to apply your changes, or click Cancel to cancel your changes. Figure 6-5: Protocol Tab - SNMP Chapter 6: Configuring the PrintServer Using the Web-based Utility The Protocol Tab - SNMP 30 Wireless-G PrintServer with Multifunction Printer Support The Wireless Tab - Basic This screen allows you to change the PrintServers basic wireless settings. Configuration Regulatory Domain and MAC Address. The PrintServers Regulatory Domain and MAC Address are listed and cannot be changed. SSID. In the SSID field, enter the name of your wireless network. This is the unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have 32 characters or fewer. Figure 6-6: Wireless Tab - Basic Channel No. If your network is set to ad-hoc mode, select your networks channel setting from the Channel No. drop-down menu. Network Type. The Network Type setting shows a choice of two wireless modes. Select Infrastructure if you want the PrintServer to communicate using an access point or wireless router. Select Ad-Hoc if you want the PrintServer to communicate without using an access point or wireless router. Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Wireless Tab - Basic 31 Wireless-G PrintServer with Multifunction Printer Support The Wireless Tab - Security Configure the security of your wireless network on this screen. Wi-Fi Protected Access (WPA) and two levels of Wired Equivalent Privacy (WEP) encryption are available. If you do not want to use wireless security, select None from the Security Mode drop-down menu. Wireless Security Security Mode. To use WPA, select Pre-Shared Key. To use WEP, select the level of WEP encryption you want to use, 64 Bit Keys (10 Hex chars) or 128 Bit Keys (26 Hex chars). Then proceed to the instructions for your security method. WEP Default Transmit Key. Select the Default Transmit Key used by your wireless network. This indicates which WEP key your network uses for WEP encryption. Passphrase. Enter a Passphrase and click the Generate Keys button to automatically generate WEP Keys 1-4. The Passphrase is case-sensitive and should have no more than 16 alphanumeric characters. It must match your wireless networks passphrase and is compatible with Linksys wireless products only. (Enter the WEP key(s) manually on any non-Linksys wireless products.) Key 1 to Key 4. To enter the WEP keys manually, leave the Passphrase field blank and enter your WEP key(s). For 64-bit WEP encryption, each key must have 10 hexadecimal characters, while for 128-bit WEP encryption, the key must have 26 hexadecimal characters. Valid hexadecimal characters are 0-9 and A-F. Authentication. Select your wireless networks authentication type. The default is Open System, for which the sender and the recipient do NOT use a WEP key for authentication. You can also choose Shared Key, for which the sender and recipient use a WEP key for authentication. Click the Save button to apply your changes, or click Cancel to cancel your changes. Pre-Shared Key (WPA) WPA Algorithm. TKIP is the default algorithm. WPA Shared Key. Enter your Pre-Shared Key, which must have 8-63 characters in length. Click the Save button to apply your changes, or click Cancel to cancel your changes. Figure 6-7: Wireless Tab - Security (WEP) Figure 6-8: Wireless Tab - Security (WPA) Chapter 6: Configuring the PrintServer Using the Web-based Utility The Wireless Tab - Security 32 Wireless-G PrintServer with Multifunction Printer Support The Printer Tab - Internet Printing Internet Printing allows you to automatically print any e-mails that are sent to a specific e-mail account on your network. This is especially useful for printing information when you are not connected to the network. You can print from any location where you can access e-mail. Mail Server Mail Server IP Address. Enter the address of your mail server. (This value must be a fixed IP address.) Account Name and Password. Enter the Account Name and Account Password. Verify Password. Enter the password again in the Verify Password field. Check Mail every. Specify how often you want the PrintServer to check for e-mail to be printed. Redirect unprintable Mail to. Specify an e-mail address to which e-mails that cannot be printed are routed; this is useful for both graphic-intensive e-mails and for troubleshooting purposes. Printer Printer Model. Enter the Printer Model in the field provided. You can find this in the Device Manager. Printer Port. Choose the appropriate Printer Port from the drop-down menu: USB, the PrintServers USB port, or Logical Printer 1-3. The PrintServer has three logical or virtual printer ports. For example, you can have three different configurations for your USB printer: Logical Printer 1 for landscape orientation, Logical Printer 2 for double-sided copies, and Logical Printer 3 for manual feed. Then configure the Logical Printers on the Logical Port tab, so Logical Printers 1, 2, and 3 will be mapped to the physical printer on the PrintServers USB port. Options Print every E-Mail. Click this checkbox if you want to print every e-mail message. Print Banner Page. Enabled by default, this feature tells the PrintServer to print a banner page for every print job

(the banner page describes the print job). Click the checkbox to remove the checkmark and disable this feature. Mail response when printed. Click this checkbox if you want an e-mail sent when a print job is complete. Click the Save button to apply your changes, or click Cancel to cancel your changes. Figure 6-9: Printer - Internet Printing Chapter 6: Configuring the PrintServer Using the Web-based Utility The Printer Tab - Internet Printing 33 Wireless-G PrintServer with Multifunction Printer Support The Printer Tab - Logical Port The Logical Printers tab contains the logical printer settings of the PrintServer. Configure them for each Logical Printer. The PrintServer has three logical or virtual printer ports. For example, you can have three different configurations for your USB printer: Logical Printer 1 for landscape orientation, Logical Printer 2 for double-sided copies, and Logical Printer 3 for manual feed. Then you will map Logical Printers 1, 2, and 3 to the physical printer on the PrintServers USB port. Select Printer Figure 6-10: Printer - Logical Port Logical Printer No. From the Logical Printer Port No: drop-down menu, select the number (1-3) of the printer you wish to configure. Click the Get Data button to update the display with the current data for the selected logical printer. Details Pre-string (Hex). Enter the printer control string (in hexadecimal characters) to be sent to the printer before each print job. This string cannot exceed 30 characters. Post String (Hex). Enter the printer control string (in hexadecimal characters) to be sent to the printer after each print job. This string cannot exceed 30 characters. Convert LF to CR+LF. If checked, LF (line feed) characters are changed to CR+LF (carriage return + line feed). Click the Save button to apply your changes, or click Cancel to cancel your changes. Chapter 6: Configuring the PrintServer Using the Web-based Utility The Printer Tab - Logical Port 34 Wireless-G PrintServer with Multifunction Printer Support The Status Tab - Device The Device tab allows you to view information about the PrintServer. Server Details The PrintServers settings and status information are displayed here. No values can be changed on this screen. This screen is for information only. Upgrade. If you want to upgrade the PrintServers firmware, follow these instructions:

1. Visit www.linksys.com and download the firmware upgrade file for the Wireless-G PrintServer. 2. Extract the file on your computer. 3. On the Device screen, click the Upgrade button. 4. On the Firmware Upgrade screen, enter the location of the extracted firmware file, or click the Browse button to find this file. 5. Click the Start Upgrade button, and follow the on-screen instructions. On the Device screen, click the Refresh button to retrieve this information again. Figure 6-11: Status Tab - Device firmware: the programming code that runs a networking device download: to receive a file transmitted over a network upgrade: to replace existing software or firmware with a newer version Chapter 6: Configuring the PrintServer Using the Web-based Utility The Status Tab - Device Figure 6-12: Firmware Upgrade 35 Wireless-G PrintServer with Multifunction Printer Support The Status Tab - Printer The Printer tab allows you to view information about the Printers. No values can be changed on this screen. This screen is for information only. Port 1 (USB Port) The ports status information is displayed here. No values can be changed on this screen. This screen is for information only. Print Test Page. Click the Print Test Page button to print a test page on the connected printer. Clicking the Refresh button causes the PrintServer to retrieve the status information again. The Status Tab - Wireless The Wireless tab allows you to view information about the PrintServers wireless connection. No values can be changed on this screen. This screen is for information only. Link Info Settings and current transmission rate for the wireless connection are displayed here. Throughput The throughput information for the wireless connection is displayed here. Clicking the Refresh button causes the PrintServer to retrieve information about the wireless connection again. The Exit Tab This tab is used exclusively for exiting the Web-based Utility. Figure 6-13: Status Tab - Printer Figure 6-14: Status Tab - Wireless Select the Exit tab, and a new screen will appear. Click the Yes button to exit the Utility, or click No to continue using the Utility. Figure 6-15: Exit Chapter 6: Configuring the PrintServer Using the Web-based Utility The Status Tab - Printer 36 Wireless-G PrintServer with Multifunction Printer Support Chapter 7: Bi-Admin Management Overview If you use Windows, then you can manage the PrintServer using its web-based utility (see Chapter 6:

Configuring the PrintServer Using the Web-based Utility) or an advanced utility program called Bi-Admin. (If you use a Macintosh or other non-Windows operating system, you can manage the PrintServer only by using its web-

based utility.) Bi-Admin is provided on the PrintServers Setup CD-ROM and is fully compatible with Windows 98, Me, 2000, and XP. It allows you to change the PrintServers internal settings, check on the units status, and perform basic diagnostic tests. Note that the Bi-Admin program must be installed only on the network administrators computer. First, install Bi-Admin on your computer. Then, you will be able to use the management utility. Bi-Admin Installation 1. Make sure you have no programs or applications running on your computer. 2. If you havent already done so, insert the Setup CD-ROM into the computers CD-ROM drive. The Setup CD-

ROM should run automatically. If it does not, click the Start button and choose Run. In the box that appears, enter D:\setupWizard.exe (if D is the letter of your CD-ROM drive). Figure 7-1: Welcome 3. Click Bi-Admin Install to continue, or click Exit to end the installation. 4. The Welcome screen of the Bi-Admin Setup program will appear first. Click Next to continue with the Bi-

Admin installation, or click Cancel to quit the setup program, and then close the open programs. Chapter 7: Bi-Admin Management Overview Figure 7-2: Bi-Admin Setup Welcome 37 Wireless-G PrintServer with Multifunction Printer Support 5. The Choose Destination Location screen will appear. Choose the location where the B-Admin folder will be installed. To install the driver in the default location, click Next. If you want the folder to be installed in a different location, click the Browse button and select the location. Then click Next. Click Back to return to the previous screen. Click Cancel to end the Bi-Admin installation. 6. The Select Program Folder screen will appear. An icon will be added to the program folder listed. You may change the name for the program folder, if you wish. Click Next. Click Back to return to the previous screen. Click Cancel to end the Bi-Admin installation. 7. When the Bi-Admin is installed, the Setup Complete screen will appear. Click Finish. Figure 7-3: Choose Destination Location Figure 7-4: Select Program Folder Chapter 7: Bi-Admin Management Bi-Admin Installation 38 Wireless-G PrintServer with Multifunction Printer Support Starting the Bi-Admin Management Utility 1. To start the Bi-Admin program, click Start, Programs, Print Server Utility, and then Bi-Admin Management Utility. If the Bi-Admin Management Utility icon has been created, you can just double-click it instead. You can drag the shortcut icon onto your Desktop for easy access to the Bi-Admin Management Utility. 2. When the Bi-Admin Management Utility appears, it will ask for the Connected Protocol. Make sure the box next to TCP/IP is checked. Click the OK button. Figure 7-5: Connected Protocol 3. The Bi-Admin Management Utility will automatically scan the network for the PrintServer. Figure 7-6: Searching for Device Chapter 7: Bi-Admin Management Starting the Bi-Admin Management Utility 39 Wireless-G PrintServer with Multifunction Printer Support The Bi-Admin Management Utility The Bi-Admin Management Utility screen will appear next. Any hardware found on the network will appear on the left-hand side of the screen. The Utility can be managed from this screen. The menu and icon options will be explained in this section. Menu Options Main. The options are Device Status, Printer Status, Configure, Upgrade, Refresh, and Exit. These options are the same as the icons that are displayed below the menu options (viewed from left to right), and are described below:

Device Status. This option allows you to view all of the device settings, optionally save the device settings to a file, or restore a previously saved file to the device. If you click Device Status, the Device Information screen will appear. A list of the PrintServers device settings is displayed, including Hardware ID, Firmware version, Protocol ID, Default Name, Server Name, and MAC Address. To save the information in a .txt (text) file, click the Save to file button. To choose a different device that you configured, click the Open button. You may then browse for your file, select it, and then click Open. The contents of the file will display on the right-hand side of the screen. To save the file to the PrintServer, click Restore to Device. Click the Exit button to return to the Bi-Admin Management Utility screen. For more information, click the Help button. Figure 7-7: Bi-Admin Management Utility Figure 7-8: Device Information Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 40 Wireless-G PrintServer with Multifunction Printer Support

Printer Status. This option allows you to view the printer status, as well as set port and printer parameters. If you click Printer Status, the Printer Status screen will appear. The Device Name will be displayed and the Current Selected Port will be highlighted. The status information for this port will be displayed. Click the Back button to return to the Bi-Admin Management Utility screen. Click Refresh to refresh the screen. For more information, click the Help button. If the printer is bi-directional and not busy, the Printer Configuration button will appear on the Printer Status screen. Click this button to view the printers Environmental Variable and Variable Value items. If the items are not read-only, you can change them based on the options of your printer. For more information, click the Help button. Figure 7-9: Printer Status Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 41 Wireless-G PrintServer with Multifunction Printer Support

Configure. You may configure the PrintServer with this option. If you click Configure, the Configuration screen will appear. It displays eight tabs: System, TCP/IP, AppleTalk, NetBEUI, Internet Printing, Port, Wireless, and SNMP. The tabs will be described below. System

Device Name. Enter the Device Name in the field provided.

Comment. Enter any comments in the Comment field.

Device Password. To change the password, select Change Device Password, enter the new password in the Password field, and then re-enter the password in the Confirm Password field.

Protocol. Select the protocol you want to use for your network: TCP/IP, AppleTalk, NetBEUI, IPX/SPX. Click the Get Defaults button if you want to cancel your changes and use the default settings. When finished making your changes on this tab, click the OK button to save these changes, or click the Cancel button to undo your changes. For more information, click the Help button. Figure 7-10: Configuration - System Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 42 Wireless-G PrintServer with Multifunction Printer Support TCP/IP

Dynamic IP Address (DHCP). If your network router is using DHCP to assign IP addresses, select Dynamic IP Address (DHCP). By default, Dynamic IP Address (DHCP) is enabled.

Fixed IP Address. If you need to assign the PrintServer a fixed IP address (also known as static IP address), select Fixed IP Address, and enter the appropriate values under IP Address, Subnet Mask, and Gateway. Make sure the IP Address and Subnet Mask are appropriate for your network. If you change the PrintServers IP address, make sure you that you reconnect to the PrintServer using that new IP address. Otherwise, you will not be communicating with the PrintServer. In most cases, the Gateway IP address is the IP address of your router, and you should complete the Gateway field if you will use the PrintServer for Internet printing. (To find out your routers IP address, consult your routers documentation.)

TCP session. If your TCP session has ended, you can attempt a new connection. In the Retry interval field, enter how often you want the PrintServer to attempt a connection. In the Retry count field, enter the maximum number of attempts. Click the Get Defaults button if you want to cancel your changes and use the default settings. When finished making your changes on this tab, click the OK button to save these changes, or click the Cancel button to undo your changes. For more information, click the Help button. Figure 7-11: Configuration - TCP/IP Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 43 Wireless-G PrintServer with Multifunction Printer Support Apple Talk

Zone Name. Typically only Macintoshes use AppleTalk, although other platforms can use it if they have the necessary, third-party software installed. Enter the Zone Name in the field provided.

Port Setting. Select the port number from the drop-down menu. The Printer Type can be obtained from the manufacturer of the printer. Enter the type of printer in the Printer Type field. For each printer connected to the PrintServer, you will choose the Communications Protocol that allows the devices on the network to communicate. Select the type of Communication Protocol you will use, ASCII or Binary for each printer, according to the recommendation of the printers manufacturer. For more information, refer to the printers documentation. Click the Get Defaults button if you want to cancel your changes and use the default settings. When finished making your changes on this tab, click the OK button to save these changes, or click the Cancel button to undo your changes. For more information, click the Help button. Figure 7-12: Configuration - AppleTalk Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 44 Wireless-G PrintServer with Multifunction Printer Support NetBEUI

Domain Name. Enter the name of the domain that you want the PrintServer associated with in the Domain Name field. If you are unsure of the Domain Name, you can find it out by looking on any computer already on the network. In Windows 98, right-click Network Neighborhood and select Properties. Under the Identification tab, there will be listed that computers name, and the Domain to which it is connected. For Windows Me, 2000, or XP, right-click My Network Places. In Windows Me, choose Properties from the menu that appears. In Windows 2000 or XP, choose Properties from the menu that appears. Then, right-

click Local Area Connection and choose Properties. The Domain name will appear. If you want the PrintServer to be connected to that same Domain, enter that Domain name here. If no Domain name exists there, you will use the Workgroup name from that window.

Port Setting. You can specify the Response Time that you prefer for the PrintServer. This is the amount of time (measured in seconds) that the PrintServer will wait for a response from the network before timing out. You also have the option to use this feature, Abort Print Job if Error. Selecting Yes here will terminate the printing if there is an error of any kind. If you select No, print jobs that have errors will be sent to the printer, but might not print properly. Click the Get Defaults button if you want to cancel your changes and use the default settings. When finished making your changes on this tab, click the OK button to save these changes, or click the Cancel button to undo your changes. For more information, click the Help button. Figure 7-13: Configuration - NetBEUI Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 45 Wireless-G PrintServer with Multifunction Printer Support Internet Printing

Mail Server. Enter the address of your mail server in the Mail Server IP Address fields. (This value must be a fixed IP address.) Enter the Mail Account name and Password next. Enter the password again in the Confirm Password field. Then, enter the time interval for the PrintServer to check for e-mail to be printed, in hours and minutes in the Check Mail Interval field. You may also specify an e-mail address to which mails that cannot be printed are routed; this is useful for both graphic-intensive e-mails and for troubleshooting purposes. Enter this e-mail address in the Redirect Mail Account field.

Printer. Select the Default Printer Port from the drop-down menu. In the field provided, enter the Printer Model, which can be found through the Device Manager.

Options. Place a check mark next to the options you want to enable: Print Every Mail, Banner Printing

(enabled by default), or Mail response when Printed. Click the Get Defaults button if you want to cancel your changes and use the default settings. When finished making your changes on this tab, click the OK button to save these changes, or click the Cancel button to undo your changes. For more information, click the Help button. Figure 7-14: Configuration - Internet Printing Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 46 Wireless-G PrintServer with Multifunction Printer Support Port

Physical Port. Select the number of the Selected Physical Port from the drop-down menu. Select the Handshake Signal, Busy Only or Busy & Ack. Select the Printer Type, High Speed or Low Speed.

Logical Port. Select the Selected Logical Port from the drop-down menu and then the physical port you want to map it to from the drop-down menu for Map to Physical Port. If you select Yes for Convert LF to LF+CR, the LF (line feed) characters are changed to LF+CR (line feed + carriage return). In the field for Prefix of Job, enter the printer control string (in hexadecimal characters) to be sent to the printer before each print job. This string cannot exceed 30 characters. In the field for Suffix of Job, enter the printer control string (in hexadecimal characters) to be sent to the printer after each print job. This string cannot exceed 30 characters. Click the Get Defaults button if you want to cancel your changes and use the default settings. When finished making your changes on this tab, click the OK button to save these changes, or click the Cancel button to undo your changes. For more information, click the Help button. Figure 7-15: Configuration - Port Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 47 Wireless-G PrintServer with Multifunction Printer Support Wireless

SSID (Service Set Identifier). In the SSID field, enter the name of your wireless network. This is the unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have 32 characters or fewer.

Channel No. If your network is set to ad-hoc mode, select your networks channel setting from the Channel No. drop-down menu.

Network Type. The Network Type setting shows a choice of two wireless modes. Select Infrastructure if you want the PrintServer to communicate using an access point or wireless router. Select Ad-Hoc if you want the PrintServer to communicate without using an access point or wireless router.

WEP Encryption. If you want to enable WEP encryption for greater wireless security, click the Enable radio button. If you want to disable WEP encryption, keep the default, Disable. From the WEP Authentication drop-down menu, select your wireless networks authentication type. The default is set to Open System, for which the sender and the recipient do NOT use a WEP key for authentication. You can also choose Shared Key, when the sender and recipient use a WEP key for authentication. This setting should match the one on your networks access point or wireless router. In the WEP Keys section, select the level of WEP encryption, 64 bits or 128-bits. From the drop-down menu, select the Default Key used by your wireless network. This indicates which WEP key your network uses for WEP encryption. In the Key1 (hex) to Key4 (hex) fields, enter your networks WEP keys. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are 0-9 and A-F. Click the Link Info button if you want to view information about the wireless connection. Click the Get Defaults button if you want to cancel your changes and use the default settings. When finished making your changes on this tab, click the OK button to save these changes, or click the Cancel button to undo your changes. For more information, click the Help button. Figure 7-16: Configuration - Wireless Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 48 Wireless-G PrintServer with Multifunction Printer Support SNMP

SysContact. Enter the name of the contact person in the SysContact field.

SysLocation. Enter the location of the contact person in the SysLocation field.

Configuration Item. From the Configuration Item box, select the number of the management station (M1-

M4) or trap receiver (T1-T4). The selected items information will be displayed below. For management stations, you can change the stations IP address, Community String, and Access Permission level. In the Manager IP Address fields, enter the IP address of the management station with the SNMP program installed. In the Community String field, enter the name of the SNMP community, which is usually public or private. In the Access Permission section, select the desired level of access for this management station, Read Only, Read/Write, or Not Accessible. For trap receivers, you can change the trap receivers IP address, Community String, Trap Option, and Trap Severity level. In the Trap Receive IP Address fields, enter the IP address of the trap receiver that will be sent the trap messages or notifications. In the Community String field, enter the name of the SNMP community, which is usually public or private. For the Trap Option setting, select Enable or Disable. For the Trap Severity setting, select the desired level of severity, with 1 meaning least severe. Click the Get Defaults button if you want to cancel your changes and use the default settings. When finished making your changes on this tab, click the OK button to save these changes, or click the Cancel button to undo your changes. For more information, click the Help button. Figure 7-17: Configuration - SNMP Chapter 7: Bi-Admin Management The Bi-Admin Management Utility 49 Wireless-G PrintServer with Multifunction Printer Support

Upgrade. You may use this option to upgrade the firmware of the PrintServer. Follow these instructions:

1. On the Upgrade screen, click the Files button. 2. The Detected LAN Cards screen will appear. Select the LAN card the PrintServer is connected to, and then click the OK button. 3. Follow the on-screen instructions, and select the firmware file you want to use. 4. View the BIN File Information screen, and click the OK button if you have selected the correct firmware file. Click the Cancel button to select a different firmware file. Figure 7-18: Upgrade 5. On the Upgrade screen, click the Upgrade button. Click the Cancel button to cancel the firmware upgrade. For more information, click the Help button.

Refresh. This option allows you to refresh the device list after you change the name or IP address of a device. The screen does not refresh automatically.

Exit. This option allows you to exit the Bi-Admin program. InitDevice. The available options are Reset Device, Restore to Factory Default, Attached Remote, and Connected Protocol. Figure 7-19: Detected LAN Cards If you click Attached Remote, the Add Cross Segment Printer screen appears. To add a cross segment print server, enter its IP address in the fields provided, and click the Set button. Click Cancel to undo any changes. For more information, click the Help button. Diagnostic. Diagnostic allows you to print a test page from either of the PrintServers ports. Help. The two options are Help Topics and About Bi-Admin. These help files offer extensive advice and details about all of the PrintServers functions and capabilities. Figure 7-20: BIN File Information Chapter 7: Bi-Admin Management The Bi-Admin Management Utility Figure 7-21: Add Cross Segment PrintServer 50 Wireless-G PrintServer with Multifunction Printer Support Chapter 8: Internet Printing Protocol (IPP) Overview Internet Printing Protocol (IPP) is a standards-based system that allows remote printing from a PC to any accessible printer. Normally, the printer will be attached to a computer or other device that functions as an IPP Server. For client PCs, it is necessary to install a compatible IPP Client program. The Client must also know the IP Address or URL of the IPP Server. The PrintServer contains the necessary firmware to act as an IPP Server. No additional configuration is necessary. However, the following requirements must be met:

The PrintServer must have a valid IP Address. For printing via the Internet, the PrintServers IP Address must be external (allocated by your ISP), rather than an IP Address on your local LAN.

Any Router, Gateway, or Firewall linking your LAN to the Internet must NOT block IPP. (IPP uses Port Services 631/TCP.)

You must advise clients of the correct URL or IP Address of the IPP Server. To use a URL rather than an IP Address, you need to register the domain name for the URL.

Unless clients are using Windows 2000 or XP, you must provide your clients with the supplied IPP Client software. If it is not convenient to provide the CD-ROM, supply the setup.exe file, located in the IPP folder. Windows IPP Client Setup Installing using setup.exe 1. Run this program, located at d:\driver\ipp\setup.exe, to unzip the included files. 2. The IPP Setup program will then run. 3. Follow the prompts to complete the installation. Chapter 8: Internet Printing Protocol (IPP) Overview 51 Wireless-G PrintServer with Multifunction Printer Support IPP Client Configuration for Windows 98, Me, 2000, and XP 1. Run the Add IPP Port program entry created by the installation. 2. On the Output Select screen, enter the IP Address or URL of the IPP Server. 3. If Internet access from your location is via a Proxy Server, check Access IPP Server via Proxy Server, and enter details of your Proxy Server. (This will be the same as your browser configuration.) 4. Click Select Device Port to view the available ports on the IPP Server, and select the appropriate port. A connection to the IPP Server will be established at this time. 5. Click OK to create the IPP port on your system. You will see a message confirming that the port has been created, and then you will see the AddPort screen. 6. Perform one of these steps. Select an existing printer to use the new port, and click OK. OR Click the Add New Printer button to create a new printer that will use the IPP port. This will start the Add Printer Wizard. Follow the prompts to complete the process. Make sure that the new printer uses the IPP port. Installation is now complete.

To create additional IPP ports, repeat the entire procedure.

The Proxy Server and other options are set individually for each IPP port. Chapter 8: Internet Printing Protocol (IPP) Windows IPP Client Setup 52 Wireless-G PrintServer with Multifunction Printer Support Changing the IPP Port Settings After the IPP port is created, you can reach the Configure IPP Port screen by performing these steps:

1. Open the Printers folder (Start => Settings => Printers). 2. Right-click IPP Printer and select Properties. 3. Click the Port Settings or Configure Port button (Details or Port tab, depending on your version of Windows). The Configure IPP Port screen will appear. There are two settings, Retry Interval and Retry Count, which can be adjusted if you have problems connecting to the IPP Server.

The Retry Interval sets the time interval (in seconds) between connection attempts. Increase this number if you have a poor connection, or the remote server is very busy.

The Retry Count sets how many connection attempts will be made. Increase this number if you have a poor connection, or the remote server is very busy. IPP Client Setup for Windows XP Windows XP has its own IPP Client, and there is no need to install the supplied IPP Client Software. To use this IPP Client with the PrintServer, follow this procedure:

1. Click the Start button. 2. Select Settings and click Printers and Faxes. 3. Click Add a printer. 4. On the Welcome to the Add Printer Wizard screen, click the Next button. 5. On the Local or Network Printer screen, select A network printer, or a printer attached to another computer, and click the Next button. Chapter 8: Internet Printing Protocol (IPP) Windows IPP Client Setup Figure 8-1: Windows XP - Local or Network Printer 53 Wireless-G PrintServer with Multifunction Printer Support 6. On the Specify a Printer screen, select Connect to a printer on the Internet or on a home or office network, and enter the URL of the IPP Server as follows (ip_address represents the IP Address of the IPP Server, and 631 represents the port number). Port 1 ip_address:631/ipp/P1 NOTE: These entries are case-sensitive. They must be entered as shown, with ipp in lowercase and P1 in uppercase. 7. If the connection can be established, and the printer on that port is online, the Connect to Printer dialog box will be displayed. This screen notifies you that the printer driver is not installed. Click the OK button. 8. Select the printer manufacturer and model to match the printer connected to the appropriate port on the IPP Server. 9. Click the OK button and follow the prompts to complete the Wizard. The IPP printer is now ready for use. Figure 8-2: Windows XP - Specify a Printer IPP Client Setup for Windows 2000 Windows 2000 has its own IPP Client, and there is no need to install the supplied IPP Client Software. To use this IPP Client with the PrintServer, follow this procedure:

1. Click the Start button. 2. Select Settings and click Printers. 3. Double-click Add Printer. 4. On the Welcome to the Add Printer Wizard screen, click the Next button. 5. Select Network Printer and click Next to see the Locate your Printer screen. 6. Select Connect to a printer on the Internet or on your intranet, and enter the URL of the IPP Server as follows (ip_address represents the IP Address of the IPP Server, and 631 represents the port number). Port 1 ip_address:631/ipp/P1 NOTE: These entries are case-sensitive. They must be entered as shown, with ipp in lowercase and P1 in uppercase. Chapter 8: Internet Printing Protocol (IPP) Windows IPP Client Setup Figure 8-3: Windows 2000 - Locate Your Printer 54 Wireless-G PrintServer with Multifunction Printer Support 7. If the connection can be established, and the printer on that port is online, the Connect to Printer dialog box will be displayed. This screen notifies you that the printer driver is not installed. Click the OK button. 8. Select the printer manufacturer and model to match the printer connected to the appropriate port on the IPP Server. 9. Click the Next button and follow the prompts to complete the Wizard. The IPP printer is now ready for use. Using IPP Printers The IPP Printer can be selected and used like any other Windows printer. If the IPP Server is not on your network, your Internet connection needs to be active. If you wish to check the availability of the remote IPP Server, you can use the Query IPP Printer program installed with the Add IPP Port program. An IPP Server may be unavailable for any of the following reasons:

It is powered off.

A printer problem has caused the IPP Server to cease responding, and a restart (reboot) is required.

The Servers IP Address has changed.

The Internet connection for the IPP Server is down.

Network congestion causes the connection attempt to time out. If using the supplied IPP Client software, there are two settings, Retry Interval and Retry Count, which can be adjusted if you have problems connecting to the IPP Server. See the previous section, Changing the IPP Port Settings, for details. Chapter 8: Internet Printing Protocol (IPP) Windows IPP Client Setup 55 Wireless-G PrintServer with Multifunction Printer Support Appendix A: Troubleshooting This appendix consists of Common Problems and Solutions. Provided are possible solutions to problems that may occur during the installation and operation of the PrintServer. Read the descriptions below to help you solve your problems. If you cant find an answer here, check the Linksys website at www.linksys.com. Common Problems and Solutions 1. All the LEDs on the front of the PrintServer are not lit. Check the power adapter and the connection to the electrical outlet. 2. The PrintServers Power LED lights up orange or flashes continuously. Reset the PrintServer. Unplug the power adapter and plug it back in, or press the Reset button on the back of the PrintServer for approximately ten seconds. 3. I am using DHCP, and the PrintServer gets an IP address conflict involving the PrintServer. If the PrintServer is left powered on when the DHCP server, which is usually the network router, is powered off, the PrintServer will retain its IP address without informing the DHCP server. Reset the PrintServer so it will obtain a new IP address. This problem may also occur if you assigned a static IP address within the range used by the DHCP server. If so, use another address NOT within the range used by the DHCP server. 4. The PrintServers Ethernet LED is not lit. Check your Ethernet network cable and make sure that the appropriate Ethernet or Link LED on your router or switch is lit. 5. A printer connected to the PrintServer cannot print or prints garbage. Do the following:

Check the cable connection between the PrintServer and printer.

Make sure the printer driver in the application program or Windows matches the printer.

Make sure the printer is not too long, less than 10 feet. 6. The Configuration button on the Printer Status screen in Bi-Admin is grayed out, even though my printer is bi-directional. The button is unavailable until the printer has finished its print jobs and sits idle. Appendix A:

Common Problems and Solutions 56 Wireless-G PrintServer with Multifunction Printer Support 7. To start over, I need to set the PrintServer to its factory default settings. Unplug the PrintServers power adapter. Press the Reset button while you plug in the PrintServers power adapter. Continue to hold the Reset button for 10 seconds and then release it. This will reset the password, wireless, and other settings on the PrintServer to the factory defaults. In other words, the PrintServer will revert to its original factory configuration. 8. I need to upgrade the firmware. In order to upgrade the firmware with the latest features, follow these steps:

1. Go to the Linksys website at http://www.linksys.com and download the latest firmware for the PrintServer. Then extract the firmware file on your PC. 2. Open the PrintServers Web-based Utility. Click Status and then Device. 3. Click the Upgrade button, and follow the on-screen instructions. 9. I want to manually change my printers IP address. Follow these steps:

1. Click Start, Settings, and Control Panel. 2. Double-click Printers and Faxes. 3. Right-click the printer you want. 4. Click Properties. 5. Click the Ports tab. 6. Select the IP port and click Configure Port. 7. On the Port Settings screen, change the IP address and click the OK button. Appendix A:

Common Problems and Solutions 57 Wireless-G PrintServer with Multifunction Printer Support Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network. Security Precautions The following is a complete list of security precautions to take:

1. Change the default SSID. 2. Disable SSID Broadcast. 3. Change the default password for the Administrator account. 4. Enable MAC Address Filtering. 5. Change the SSID periodically. 6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce your network performance. 7. Change the WEP encryption keys periodically. To ensure network security, at least steps one through five should be followed. Security Threats Facing Wireless Networks Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking products first listen for beacon messages. These messages can be easily decrypted and contain much of the networks information, such as the networks SSID (Service Set Identifier). Here are the steps you can take:

Change the administrators password regularly. With every wireless networking device you use, keep in mind that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only person who can change network settings. If a hacker gets a hold of the administrators password, he, too, can change those settings. So, make it harder for a hacker to get that information. Change the administrators password regularly. NOTE: Some of these security features are available only through the network router or access point. Refer to the router or access points documentation for more information. Appendix B: Wireless Security Security Precautions 58 Wireless-G PrintServer with Multifunction Printer Support SSID. There are several things to keep in mind about the SSID:

1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, dont broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is linksys.) Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you use. Change your SSID regularly so that any hackers who have gained access to your wireless network will have to start from the beginning in trying to break in. MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with a random MAC Address. WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security concerns. This is overstating WEPs ability. Again, this can only provide enough security to make a hackers job more difficult. There are several ways that WEP can be maximized:

1. Use the highest level of encryption possible 2. Use Shared Key authentication 3. Change your WEP key regularly WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Two modes are available: Pre-Shared Key and RADIUS. Pre-Shared Key gives you a choice of two encryption methods: TKIP

(Temporal Key Integrity Protocol), which utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers, and AES (Advanced Encryption System), which utilizes a symmetric 128-Bit block data encryption. RADIUS (Remote Authentication Dial-In User Service) utilizes a RADIUS server for authentication and the use of dynamic TKIP, AES, or WEP. IMPORTANT: Always remember that each device in your wireless network MUST use the same encryption method and encryption key or your wireless network will not function properly. Appendix B: Wireless Security Security Threats Facing Wireless Networks 59 Wireless-G PrintServer with Multifunction Printer Support WPA Pre-Shared Key. If you do not have a RADIUS server, select the type of algorithm, TKIP or AES, enter a password in the Pre-Shared key field of 8-64 characters, and enter a Group Key Renewal period time between 0 and 99,999 seconds, which instructs the Router or other device how often it should change the encryption keys. WPA RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) First, select the type of WPA algorithm, TKIP or AES. Enter the RADIUS servers IP Address and port number, along with a key shared between the device and the server. Last, enter a Group Key Renewal period, which instructs the device how often it should change the encryption keys. RADIUS. WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) First, enter the RADIUS servers IP Address and port number, along with a key shared between the device and the server. Then, select a WEP key and a level of WEP encryption, and either generate a WEP key through the Passphrase or enter the WEP key manually. Implementing encryption may have a negative impact on your networks performance, but if you are transmitting sensitive data over your network, encryption should be used. These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer. Appendix B: Wireless Security Security Threats Facing Wireless Networks 60 Wireless-G PrintServer with Multifunction Printer Support Appendix C: About Bi-Directional Printing Normal printing only sends print signals from a PC to a printer. Bi-directional printing, also called bitronic printing, refers to a printers ability to do just the oppositetalk back to a PC to notify it of a print job status, paper jams, etc. This two-way communication technology can be found in HP, IBM, Panasonic, and other laser or color printers where close contact between the PC and printer is key. In color printing, for example, the printer informs the PC of its constant status in order to mix color inks correctly for optimal quality output. Bi-directional communication, communication from a printer to a PC, is normally handled by a combination of the printer hardware and special software on your computer. Using a bi-directional printer on a network poses unique challenges. Unlike a direct PC-to-printer connection during which a bi-directional printer can easily send its signals back to the host PC through the computers parallel or USB port (which is normally located only a few feet away from the printer), a networked printer faces the problem of having to route messages bound for a particular PC through a large array of hubs, switches, file servers, and computers. Unfortunately, most printers are not equipped to handle the complexities of printer-to-PC communication across a network. That does not mean that they cant be used on a network, however. Linksys designed the PrintServers to function with both regular as well as bi-directional printers. However, the PrintServer cannot pass messages from the printer back to the printing PCthis limitation is simply an industry standard, and not one of the PrintServer itself. However, the PrintServer can check any printers online and printing status on the network using the Bi-Admin management utility software packaged with the PrintServer. The status-checking feature built into the management software does not require a bi-directional printer to function. If your printer came with special bi-directional software allowing you to monitor printer status, do not use it with the PrintServerthe software is most likely not network-

capable. For best results, turn off the printers bi-directional function either by (1) removing any bi-directional printing software from your network computers, and/or (2) turning off the printers bi-directional print feature inside of the printers on-board menus (if it has menus). Your printers user guide should be able to provide specific instructions for doing this. Appendix C: About Bi-Directional Printing 61 Wireless-G PrintServer with Multifunction Printer Support Appendix D: Upgrading Firmware Use the PrintServers Web-based Utility to upgrade its firmware. Follow these instructions:

1. Visit www.linksys.com and download the firmware upgrade file for the Wireless-G PrintServer with Multifunction Printer Support. 2. Extract the file on your computer. 3. Open the PrintServers Web-based Utility. 4. Click the Status tab, and then click the Device tab. 5. On the Device screen, click the Upgrade button. 6. On the Firmware Upgrade screen, enter the location of the extracted firmware file, or click the Browse button to find this file. 7. Click the Start Upgrade button, and follow the on-screen instructions. Figure D-1: Status Tab - Device Figure D-2: Firmware Upgrade Appendix D: Upgrading Firmware 62 Wireless-G PrintServer with Multifunction Printer Support Appendix E: Windows Help Almost all Linksys wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides complete instructions on enabling TCP/IP. Shared Resources If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on utilizing shared resources. Network Neighborhood/My Network Places Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the version of Windows you're running). Windows Help provides complete instructions on adding PCs to your network. Appendix E: Windows Help 63 Wireless-G PrintServer with Multifunction Printer Support Appendix F: Glossary This glossary contains some basic networking terms you may come across when using this product. For more advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary. Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network. Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point. AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption. Bandwidth - The transmission capacity of a given device or network. Bit - A binary digit. Boot - To start a device and cause it to start executing instructions. Broadband - An always-on, fast Internet connection. Browser - An application program that provides a way to look at and interact with all the information on the World Wide Web. Byte - A unit of data that is usually eight bits long. Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet. Daisy Chain - A method used to connect devices in a series, one after the other. DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address. Default Gateway - A device that forwards Internet traffic from your local area network. DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign temporary IP addresses to network computers by leasing an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses. Appendix F: Glossary 64 Wireless-G PrintServer with Multifunction Printer Support DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be seen from the Internet. DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. Domain - A specific name for a network of computers. Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines. Dynamic IP Address - A temporary IP address assigned by a DHCP server. EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access. Many specific authentication methods work within this framework. Encryption - Encoding data transmitted in a network. Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Firewall - A set of related programs located at a network gateway server that protects the resources of a network from users from other networks. Firmware - The programming code that runs a networking device. FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network. Full Duplex - The ability of a networking device to receive and transmit data simultaneously. Gateway - A device that interconnects networks with different, incompatible communications protocols. Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time. HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World Wide Web. Infrastructure - A wireless network that is bridged to a wired network via an access point. IP (Internet Protocol) - A protocol used to send data over a network. Appendix F: Glossary 65 Wireless-G PrintServer with Multifunction Printer Support IP Address - The address used to identify a computer or device on a network. IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network. MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission. NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet. Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users. Packet - A unit of data sent over a network. Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products. Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online. POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet. Port - The connection point on a computer or networking device used for plugging in cables or adapters. Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power. PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication

(username and password) in addition to data transport. PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe. RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control network access. Appendix F: Glossary 66 Wireless-G PrintServer with Multifunction Printer Support RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires. Roaming - The ability to take a wireless device from one access point's range to another without losing the connection. Router - A networking device that connects multiple networks together. Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet. SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol. SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before allowing them to enter the network. SSID (Service Set IDentifier) - Your wireless network's name. Static IP Address - A fixed address assigned to a computer or device that is connected to a network. Static Routing - Forwarding data in a network via a fixed path. Subnet Mask - An address code that determines the size of the network. Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an electrical circuit. TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent. TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a network. Telnet - A user command and TCP/IP protocol used for accessing remote PCs. TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password capability. Throughput - The amount of data moved successfully from one node to another in a given time period. Appendix F: Glossary 67 Wireless-G PrintServer with Multifunction Printer Support TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. Topology - The physical layout of a network. TX Rate - Transmission Rate. Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network. URL (Uniform Resource Locator) - The address of a file located on the Internet. VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another over the Internet. WAN (Wide Area Network)- The Internet. WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security. WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each other wirelessly. WPA (Wi-Fi Protected Access) - A wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server. Appendix F: Glossary 68 Wireless-G PrintServer with Multifunction Printer Support Appendix G: Specifications Model Standards Ports Button WPSM54G IEEE 802.11g, IEEE 802.11b, IEEE 802.3, USB 2.0 Power, Ethernet, USB Printer Reset Cabling Type USB 2.0, UTP CAT5 LEDs Power, Ethernet, Wireless, USB Security Features WEP, WPA-PSK WEP Key Bits 64, 128 Dimensions

(W x H x D) Unit Weight Power 5.24" x 0.98" x 2.76"

(133 mm x 25 mm x 70 mm) 3.80 oz. (0.11 kg) 5 V DC, 2A Certifications FCC, CE Operating Temp. 0C to 40C (32F to 104F) Storage Temp.

-20C to 70C (-4F to 158F) Operating Humidity 10% to 85%, Non-Condensing Storage Humidity 5% to 90%, Non-Condensing Appendix G: Specifications 69 Wireless-G PrintServer with Multifunction Printer Support Appendix H: Warranty Information LIMITED WARRANTY Linksys warrants to You that, for a period of three years (the Warranty Period), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser. If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges. ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction. This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or attack. TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT

(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. Appendix H: Warranty Information 70 Wireless-G PrintServer with Multifunction Printer Support Appendix I: Regulatory Information FCC STATEMENT This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment or devices Connect the equipment to an outlet other than the receiver's Consult a dealer or an experienced radio/TV technician for assistance FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. INDUSTRY CANADA (CANADA) This Class B digital apparatus complies with Canadian ICES-003, RSS210. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. EC DECLARATION OF CONFORMITY (EUROPE) Linksys declares that this product conforms to the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC:

EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment. EN 609 50 Safety Appendix I: Regulatory Information 71 Wireless-G PrintServer with Multifunction Printer Support EN 300-328-1, EN 300-328-2 Technical requirements for Radio equipment. Caution: This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact local Authority for procedure to follow. Note: Combinations of power levels and antennas resulting in a radiated power level of above 100 mW equivalent isotropic radiated power (EIRP) are considered as not compliant with the above mentioned directive and are not allowed for use within the European community and countries that have adopted the European R&TTE directive 1999/5/EC. For more details on legal combinations of power levels and antennas, contact Linksys Corporate Compliance. Linksys vakuuttaa tten ett dieses produkt tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien niden direktiivien muiden ehtojen mukainen. Linksys dclare que le produit est conforme aux conditions essentielles et aux dispositions relatives la directive 1999/5/EC. Belgique:

Dans le cas d'une utilisation prive, l'extrieur d'un btiment, au-dessus d'un espace public, aucun enregistrement n'est ncessaire pour une distance de moins de 300m. Pour une distance suprieure 300m un enregistrement auprs de l'IBPT est requise. Pour une utilisation publique l'extrieur de btiments, une licence de l'IBPT est requise. Pour les enregistrements et licences, veuillez contacter l'IBPT. France:

2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respectivement) sont compltement libres d'utilisation en France (en utilisation intrieur). Pour ce qui est des autres canaux, ils peuvent tre soumis autorisation selon le dpartment. L'utilisation en extrieur est soumis autorisation pralable et trs restreint. Vous pouvez contacter l'Autorit de Rgulation des Tlcommunications (http://www.art-telecom.fr) pour de plus amples renseignements. SAFETY NOTICES Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Appendix I: Regulatory Information 72 Wireless-G PrintServer with Multifunction Printer Support Appendix J: Contact Information Need to contact Linksys?

Visit us online for information on the latest products and updates to your existing products at:

Can't find information about a product you want to buy on the web? Do you want to know more about networking with Linksys products? Give our advice line a call at:

Or fax your request in to:

If you experience problems with any Linksys product, you can call us at:

Don't wish to call? You can e-mail us at:

If any Linksys product proves defective during its warranty period, you can call the Linksys Return Merchandise Authorization department for obtaining a Return Authorization Number at:

(Details on Warranty and RMA issues can be found in the Warranty Information section in this Guide.) http://www.linksys.com or ftp.linksys.com 800-546-5797 (LINKSYS) 949-823-3002 800-326-7114 support@linksys.com 949-823-3000 Appendix J: Contact Information 73