| submitted | available | document details (if available) | source link |
|---|---|---|---|
| November 30 2009 | November 30 2009 | Microsoft Word - nL400manualREV0.20.FCC.doc Hany Shenouda Acrobat Distiller 8.1.0 (Windows) |
| various | User Manual | Users Manual | 66.63 KiB | November 30 2009 |
Model: nL400 Operating Manual nL400 400480 MHz Narrowband Modem Revision 0.20, November 18, 2009 Microhard Systems Inc.
#17, 2135 32nd Ave N.E. Calgary, Alberta T3K 4Z4 Phone: (403) 248-0028 Fax: (403) 248-2762 www.microhardcorp.com Warranty Microhard Systems Inc. warrants that each product will be free of defects in material and workmanship for a period of one (1) year for its products. The warranty commences on the date the product is shipped by Microhard Systems Inc. Microhard Systems Inc.s sole liability and responsibility under this warranty is to repair or replace any product which is returned to it by the Buyer and which Microhard Systems Inc. determines does not conform to the warranty. Product returned to Microhard Systems Inc. for warranty service will be shipped to Microhard Systems Inc. at Buyers expense and will be returned to Buyer at Microhard Systems Inc.s expense. In no event shall Microhard Systems Inc. be responsible under this warranty for any defect which is caused by negligence, misuse or mistreatment of a product or for any unit which has been altered or modified in any way. The warranty of replacement shall terminate with the warranty of the product. Warranty Disclaims Microhard Systems Inc. makes no warranties of any nature of kind, expressed or implied, with respect to the hardware, software, and/or products and hereby disclaims any and all such warranties, including but not limited to warranty of non-infringement, implied warranties of merchantability for a particular purpose, any interruption or loss of the hardware, software, and/or product, any delay in providing the hardware, software, and/or product or correcting any defect in the hardware, software, and/or product, or any other warranty. The Purchaser represents and warrants that Microhard Systems Inc. has not made any such warranties to the Purchaser or its agents MICROHARD SYSTEMS INC. EXPRESS WARRANTY TO BUYER CONSTITUTES MICROHARD SYSTEMS INC. SOLE LIABILITY AND THE BUYERS SOLE REMEDIES. EXCEPT AS THUS PROVIDED, MICROHARD SYSTEMS INC. DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PROMISE. MICROHARD SYSTEMS INC. PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE USED IN ANY LIFE SUPPORT RELATED DEVICE OR SYSTEM RELATED FUNCTIONS NOR AS PART OF ANY OTHER CRITICAL SYSTEM AND ARE GRANTED NO FUNCTIONAL WARRANTY. Indemnification The Purchaser shall indemnify Microhard Systems Inc. and its respective directors, officers, employees, successors and assigns including any subsidiaries, related corporations, or affiliates, shall be released and discharged from any and all manner of action, causes of action, liability, losses, damages, suits, dues, sums of money, expenses
(including legal fees), general damages, special damages, including without limitation, claims for personal injuries, death or property damage related to the products sold hereunder, costs and demands of every and any kind and nature whatsoever at law. IN NO EVENT WILL MICROHARD SYSTEMS INC. BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL, BUSINESS INTERRUPTION, CATASTROPHIC, PUNITIVE OR OTHER DAMAGES WHICH MAY BE CLAIMED TO ARISE IN CONNECTION WITH THE HARDWARE, REGARDLESS OF THE LEGAL THEORY BEHIND SUCH CLAIMS, WHETHER IN TORT, CONTRACT OR UNDER ANY APPLICABLE STATUTORY OR REGULATORY LAWS, RULES, REGULATIONS, EXECUTIVE OR ADMINISTRATIVE ORDERS OR DECLARATIONS OR OTHERWISE, EVEN IF MICROHARD SYSTEMS INC. HAS BEEN ADVISED OR OTHERWISE HAS KNOWLEDGE OF THE POSSIBILITY OF SUCH DAMAGES AND TAKES NO ACTION TO PREVENT OR MINIMIZE SUCH DAMAGES. IN THE EVENT THAT REGARDLESS OF THE WARRANTY DISCLAIMERS AND HOLD HARMLESS PROVISIONS INCLUDED ABOVE MICROHARD SYSTEMS INC. IS SOMEHOW HELD LIABLE OR RESPONSIBLE FOR ANY DAMAGE OR INJURY, MICROHARD SYSTEMS INC.'S LIABILITY FOR ANYDAMAGES SHALL NOT EXCEED THE PROFIT REALIZED BY MICROHARD SYSTEMS INC. ON THE SALE OR PROVISION OF THE HARDWARE TO THE CUSTOMER. Proprietary Rights The Buyer hereby acknowledges that Microhard Systems Inc. has a proprietary interest and intellectual property rights in the Hardware, Software and/or Products. The Purchaser shall not (i) remove any copyright, trade secret, trademark or other evidence of Microhard Systems Inc.s ownership or proprietary interest or confidentiality other proprietary notices contained on, or in, the Hardware, Software or Products, (ii) reproduce or modify any Hardware, Software or Products or make any copies thereof, (iii) reverse assemble, reverse engineer or decompile any Software or copy thereof in whole or in part, (iv) sell, transfer or otherwise make available to others the Hardware, Software, or Products or documentation thereof or any copy thereof, except in accordance with this Agreement. ii nL400 Operating Manual nL400 Regulatory Requirements PLEASE READ THIS SECTION CAREFULLY To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance is based on the above them ranging from 39 cm to 305 cm between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. WARNING:
Antenna Minimum Gain Maximum Gain Impedance
(ohms) 50 50 Antenna Gain (dBi) Minimum Separation Distance (cm) 0 18 24 192 WARNING:
EQUIPMENT LABELING The FCC and IC numbers depend on the model of the radio module. Do NOT use the Marketing Name of the product but the Model to distinguish the Certifications Numbers. This device has been modularly approved. The manufacturer, product name, and FCC and Industry Canada identifiers of this product must appear on the outside label of the end-user equipment. SAMPLE LABEL REQUIREMENT for Model: nL400:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Contains:
FCCID: NS909P30 IC : 3143A-09P30 nL400 Operating Manual: Contents iii Contents Warranty ....................................................................................................................................................................... ii Warranty Diclaims ........................................................................................................................................................ ii Indemnification ............................................................................................................................................................. ii Proprietary Rights ......................................................................................................................................................... ii nL400 Regulatory Requirements ................................................................................................................................. iii CONTENTS .............................................................................................................................................................. IV 2. GENERAL ........................................................................................................................................................... 1 PRODUCT OVERVIEW ........................................................................................................................................................ 1 OUTPUT POWER LEVEL ..................................................................................................................................................... 2 INSTALLATION ................................................................................................................................................. 4 OVERVIEW ....................................................................................................................................................................... 4 ESTIMATING THE GAIN MARGIN ....................................................................................................................................... 4 ANTENNAS AND CABLING ................................................................................................................................................. 6 3.2.1 ........................................................................................................................ Internal Cabling
............................................................................................................................................................................... 6 3.2.2 ............................................................ Installing External Cables, Antennas and Lightning Arrestors
............................................................................................................................................................................... 7 3.0 3.1 3.2 2.0 2.1 3. iv nL400 Operating Manual 2. General 2.0 Product Overview The nL400 is a high-performance embedded wireless data transceiver. Operating in the 400 - 480 MHz band, this narrowband module is capable of providing reliable wireless data transfer between almost any type of equipment which uses an asynchronous serial interface. The small-size and superior RF performance of this module make it ideal for many applications. While a pair of nL400 modules can link two terminal devices (point-to-
point operation); multiple modules can be used together to create a network of various topologies, including point-to-multipoint and repeater operation. Multiple independent networks can operate concurrently, so it is possible for unrelated communications to take place in the same or a nearby area without sacrificing privacy or reliability. 1.1 Features Key features of the nL400 include:
a serial I/O data port with handshaking and hardware flow control, allowing the nL400 to interface directly to any equipment with an asynchronous serial interface.
ease of installation and use the nL400 module uses a subset of standard AT style commands, very similar to those used by traditional telephone line modems.
all units in a system are physically identical, and can be configured as a master, repeater or slave using the AT command set. No hardware modifications are required
32-bit of CRC error detection and auto re-transmit to provide accuracy and reliability of data. nL400 Operating Manual: Chapter2 General 1
TDMA (time division multiple access) support, allowing multi-slave access in point-to-point mode.
roaming ability, allowing repeaters and slaves to re-
synchronize with a new master if the synchronization pulse from the original master is lost. While the typical application for the nL400 is to provide a short- to mid-
range wireless communications link between DTEs, it can be adapted to almost any situation where an asynchronous serial interface is used and data intercommunication is required. 2.1 Output Power Level The Output Power Level determines at what power the nL400 transmits. The nL400s sensitive receiver can operate with very low power levels, so it is recommended that the lowest power necessary is used; using excessive power contributes to unnecessary RF pollution. Ideally, you should test the communications performance between units starting from a low power level and working upward until the RSSI is sufficiently high and a reliable link is established. The conditions will vary widely between applications, the output power settings can be calculated based on following information. Transmitter antenna gain Cable loss Effective radiated power (ERP) requirement by FCC Regulations Power Setting = 36 Antenna Gain Cable Loss The power setting must be no more than the above calculation value. Any higher is a violation of FCC rules. See IMPORTANT warning below. Table 1 Output Power Power Setting
(dBm) Approx. Output Power
(mW) 0 20 21 22 23 24 25 26 27 28 29 30 33 35 37 1 100 125 160 200 250 320 400 500 630 800 1000 2000 3162 5000 2 nL400 Operating Manual: Chapter 2 General nL400 Operating Manual: Chapter2 General 3 3. Installation 3.0 Overview Qualified and experienced personnel must carry out the installation, removal or maintenance of all antenna components. The nL400 complies with FCC part 15 at the modular level for operation in the license-free 400 to 480MHz depending on the country of operation there maybe some band restrictions. This chapter provides guidelines for installing and deploying equipment which incorporates the nL400 module. 3.1 Estimating the Gain Margin Successful communication between nL400 modules is dependent on three main factors:
System Gain Path Loss System gain is a calculation in dB describing the performance to be expected between a transmitter-receiver pair. The number can be calculated based on knowledge of the equipment being deployed. The following four factors make up a system gain calculation:
1. Transmitter power (user selectable) 2. Transmitter gain (transmitting antenna gain minus cabling loss between Interference the transmitting antenna and the nL400 module) 3. Receiver gain (Receiving antenna gain minus cabling loss between the receiving antenna and the module) 4. Receiver sensitivity (Specified as -108dBm on the nL400 module) In the following illustration, the transmitting antenna has a gain of 6 dB, and the receiving antenna has a gain of 3 dB. The cable loss between the module and the antenna is 2 dB on both the transmitting and receiving side. Cable Loss = 2 dB Cable Loss = 2 dB Antenna Gain = 6 dB Antenna Gain = 3 dB Transmitter 30 dBm Output Power Receiver Sensitivity =
-105 dBm 4 nL400 Operating Manual: Chapter 3 Installation Figure 1 Gain Calculation The power level has been set to 30dBm (1W) on the transmitter, and the receiver sensitivity for the nL400 is -108dBm. System gain would be calculated to be:
30 - 2 + 6 + 3 - 2 + 108 = 143 dB. Base Height (m) Mobile Height
(m) Distance (km) Figure 2 System Deploying When deploying your system, care must be taken to ensure the path loss
(reduction of signal strength from transmitter to receiver in dB) between equipment does not exceed the system gain (140 dB in the above example). It is recommended to design for a gain margin of at least 20 dB to ensure reliable communication. Gain margin is the difference between system gain and path loss. Referring to the same example, suppose the path loss is 100 dB, the gain margin would be 40 dB, which is more than adequate for reliable communication. Path loss is a very complicated calculation which mainly depends on the terrain profile, and the height of the antennas off the ground. The following table provides path loss numbers for varying antenna heights and antenna separation: These numbers are real averages taken from rural environments. They do not apply to urban, non-line-of-sight environments. Table 2 Path Loss Distance
(km) 5 5 8 8 8 16 16 16 16 16 16 Base Height
(m) 15 30 15 15 15 15 15 15 30 30 30 Mobile Height
(m) 2.5 2.5 2.5 5 10 2.5 5 10 10 5 2.5 Path Loss
(dB) 116.5 110.9 124.1 117.7 105 135.3 128.9 116.2 109.6 122.4 128.8 MHX-920 Operating Manual:Glossary 5 WARNING:
Qualified and experienced personnel must carry out the installation, removal or maintenance of all antenna components. Once the equipment is deployed, you can verify the signal strength by entering into Command Mode and reading Register S123. This register provides the average signal strength in dBm. The minimum strength for communication is roughly -108dBm. For consistent reliable communication, you should try to deploy the equipment such that signal strength exceeds -95dBm. 3.2 Antennas and Cabling This section describes the recommended procedure for installing cabling and antennas for use with the nL400 module. 3.2.1 Internal Cabling The most common method for installing the module is to run a cable from the modules MCX connector to a reverse TNC, N-female, or SMA bulkhead connector on the chassis of the equipment as shown in Figure 3. This cable can be purchased from Microhard Systems. External Antenna Connector RG316 Cable with MCX male connector and Reverse TNC bulkhead connector MCX female connector 0 0 4 L n Figure 3 Suggested Internal Cabling Cable losses are negligible for the short piece used within the chassis. Additional losses up to 0.5 dB may be present in the MCX and Reverse TNC connections. 6 MHX-920 Operating Manual: Glossary WARNING:
Direct human contact with the antenna is potentially unhealthy when the nL400 is generating RF energy. Always ensure that the nL400 equipment is powered down during installation. WARNING:
Never work on an antenna system when there is lightning in the area. 3.2.2 Installing External Cables, Antennas and Lightning Arrestors Qualified and experienced personnel must carry out the installation, removal or maintenance of all antenna components. Never work on an antenna system when there is lightning in the area. Direct human contact with the antenna is potentially unhealthy when the nL400 is generating RF energy. Always ensure that the nL400 equipment is powered down during installation. At all times a distance of shown below should be maintained between the antenna and any person when the device is in operation. Antenna Min Gain Max Gain Impedance
(ohms) 50 50 Antenna Gain (dBi) 0 18 Minimum Separation Distance (cm) 39 305 Surge Arrestors The most effective protection against lightning is to install two lightning
(surge) arrestors, one at the antenna, the other one at the interface with the equipment. The surge arrestor grounding system should be fully interconnected with the transmission tower and power grounding systems to form a single, fully integrated ground circuit. Typically, both ports on surge arrestors are N-female. External Filter Although the nL400 is capable of filtering out RF noise in most environments, there are circumstances that require external filtering. Paging towers and cellular base stations in close proximity to the nL400 antenna can desensitize the receiver. Microhard Systems external cavity filter eliminates this problem. The filter has two N-female ports and should be connected in line at the interface to the RF equipment. Cabling The following coax cables are recommended:
Table 3 Cable Loss Cable Loss (dB/100ft) LMR 195 LMR 400 LMR 600 10.7 3.9 2.5 MHX-920 Operating Manual:Glossary 7 WARNING:
The nL400 can only be used with any antennas listed in Appendix A and this the antenna separations shown in Appendix A. WARNING:
Be careful with dBi vs dBd gains on antenna specifications. Antenna manufactures may not clearly indicate the gain on the antenna if it is dBd or dBi. Note 1dBd 2.15dBi.
=
Factors to take into consideration when choosing a cable are:
price;
bend radius limitations (the lower performance cables generally can bend more sharply) performance requirements; and, distance between the equipment and the antenna. When installing the cable, always begin fastening at the top near the antenna connector/surge arrestor. The cable must be supported at the top with a hose clamp or wrap lock, and at 5 ft intervals down the length of the tower. Over-tightening the fasteners will dent the cable and reduce performance. If properly grounded surge arrestors are not installed at both the top and the bottom of the cable, then the cable should be grounded to the tower at these locations using a cable grounding kit. If the tower is non-
conductive, then a separate conductor, physically separate from the cable, should be run down the tower. Antenna Before choosing an antenna, you should have some knowledge of the path loss and the topology of the equipment. If the equipment is in a fixed location and is to communicate with only one other unit also in a fixed location, then a Yagi antenna is suitable. Choose a Yagi with enough gain to ensure adequate gain margin. When deploying the Yagi, point the antenna towards the intended target, ensuring the antenna elements are perpendicular to the ground for vertical polarization. In applications where there are multiple units that you must communicate with or units, which are in motion, you may select an Omni-directional antenna with appropriate gain. See appendix A for a list of approved antennas types that can be used with the nL400 radio modem. If you require another type of antenna please contact Microhard Systems Inc. Microhard Systems Inc. can provide you with approved antennas to ensure FCC and Industry Canada compliance. ERP is calculated as follows:
ERP = Tx Power(dBm) - Cable/Connector Loss(dB) + Ant Gain(dBi) Antenna Gains must be in dBi when calculating the 36dBm ERP limit. 1dBd = 2.15dBi Use the guidelines in the previous section for calculating cable and connector losses. If cabling and connector losses are 2 dB, then the maximum allowable gain of the antenna will be 8 dB. 8 MHX-920 Operating Manual: Glossary A. Antenna / Separations Antenna Minimum Gain Maximum Gain Impedance
(ohms) 50 50 Antenna Gain (dBi) 0 18 RF EXPOSURE DISTANCE LIMITS Minimum Separation Distance (cm) 24 192 r
=
GP S 4
=
EIRP S 4 Sample calculation:
S = 406.1/1500 mW/cm2 EIRP = 51 dBm = 1055/10 mW = 125893 mW (Worst Case)
(Minimum Safe Distance, r) =
EIRP S 4
=
125893
/1.406
(
) 1500 4 192 cm WARNING:
Changes or modifications not expressly approved by Microhard Systems Inc. could void the users authority to operate the equipment. Please Contact Microhard Systems Inc. if you need more information. WARNING:
To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance is based on the above them ranging from 24 cm to 192 cm between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. MHX-920 Operating Manual:Glossary 9
This product uses the FCC Data API but is not endorsed or certified by the FCC