HIGH POWER N MINIPCI 5.8GHz Users Manual

 

High Power N MiniPCI 5.8GHz 2 x 2 802.11N MIMO mini-PCI Modules XN58-26 5GHz Single-Band 802.11n MIMO 2 x 2 miniPCI Features Atheros XSPAN family chipset IEEE 802.11n compliant and backward compatible with 802.11a Enhanced sensitivity Optimized isolation path Maximum output power 26dBm@802.11a / 28dBm MIMO aggregate Built-in ESD Protection with ESD/EMP Immunity Threshold: 15KeV Multi-Country Roaming Supported (IEEE802.11d Global Harmonization Standard) 2 x MMCX connectors allowing for improved mechanical stability and low loss Superior thermal performance Chipset Host Interface Operating Voltage Power Consumption Antenna Connector Data Rate Frequency Range Modulation Techniques RoHS Compliance Temperature Range Humidity Dimension 802.11a Atheros AR9220 32-bit mini-PCI Type IIIA+ (6.55mm longer than IIIA type) Technical Specifications 3.3 VDC 11a Cont. Tx @6M 11na Cont. Tx@HT20 MCS0 11na Cont. Tx@HT40 MCS0 11a Cont. Rx Standby 4.9W 4.3W 4.8W 2.5W 0.8W 2 x MMCX connector IEEE 802.11a : 54Mbps 48Mbps 36Mbps 24Mbps 18Mbps 12Mbps 9Mbps 6Mbps IEEE 802.11n :

20MHz 40MHz 1Nss: 65Mbps @ 800GI, 72.2Mbps @ 400GI (Max.) 2Nss: 130Mbps @ 800GI, 144.4Mbps @ 400GI (Max.) 1Nss: 135Mbps @ 800GI, 150Mbps @ 400GI (Max.) 2Nss: 270Mbps @ 800GI, 300Mbps @ 400GI (Max.) IEEE 802.11a/n:

5.725 ~ 5.850 GHz (US & Canada) 5.725 ~ 5.875 GHz (Europe) OFDM: BPSK, QPSK, 16-QAM, 64-QAM Yes Operating: -20C to 70C Storage: -40C to 90C Operating:5% to 95% (non-condensing) Storage: Max.90% (non-condensing) 59.6mm x 57.5mm x 7.5mm XN58-26 MIMO MINIPCI CARD RADIO TX SPECIFICATIONS DataRate 6-24Mbps 36Mbps 48Mbps 54Mbps TX Power

(per chain) 26dBm 25dBm 24dBm 23dBm TX Power

(2 chains) 28dBm 28dBm 27dBm 26dBm Tolerance 2dB 2dB 2dB 2dB 5GHz 11n HT 20 DataRate TX Power

(per chain) MCS 0/8 25dBm MCS 1/9 25dBm MCS 2/10 23.5dBm MCS 3/11 23.5dBm MCS 4/12 22.5dBm MCS 5/13 22dBm MCS 6/14 21dBm MCS 7/15 20dBm TX Power

(2 chains) 28dBm 28dBm 26.5dBm 26.5dBm 25.5dBm 25dBm 24dBm 23dBm Tolerance 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB RX SPECIFICATIONS 5GHz 11n HT 40 DataRate TX Power

(per chain) MCS 0/8 24dBm MCS 1/9 24dBm 22.5dBm MCS 2/10 22.5dBm MCS 3/11 22dBm MCS 4/12 MCS 5/13 20.5dBm 20.5dBm MCS 6/14 MCS 7/15 17dBm TX Power

(2 chains) 27dBm 27dBm 25.5dBm 25.5dBm 25dBm 23.5dBm 23.5dBm 20dBm Sensitivity

(2 chains)

-96dBm

-96dBm

-95dBm

-93dBm

-95dBm

-93dBm

-90dBm

-89dBm

-85dBm

-81dBm

-79dBm

-75dBm Tolerance DataRate 802.11a 5GHz 11n HT 40 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 24M 36M 48M 54M MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 Sensitivity

(2 chains)

-89dBm

-86dBm

-82dBm

-79dBm

-92dBm

-90dBm

-87dBm

-84dBm

-81dBm

-77dBm

-76dBm

-74dBm DataRate 6M 9M 12M 18M MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 802.11a 5GHz 11n HT 20 Tolerance 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB Tolerance 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB 2dB Cable Dimensions Terminal Material Attachment Procedure Ordering Information CODES XN58-26 ESD CABLE SPECIFICATION 26cm length Copper End of ESD Cable tied to Earth Ground Connectors type Carton Dimension MMCX For 50pcs (pcs/ctn), 0.40m * 0.22m * 0.085m / 0.006 = 1.5KG For 250pc (pcs/ctn), 0.45m * 0.45m * 0.24m / 0.006 = 8.1KG Please contact Compex sales representatives for other available configurations

Module grounding cable included

Configurations are subject to change without notice COMPLIANCE INFORMATION This device complies with the following radio frequency and safety standards. Important to OEM Manufacturer:

This following FCC Warning must be included in the HOST User Manual. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. Note 1: This module certified that complies with RF exposure requirment under mobile or fixed condition, this module is to be installed only in mobile or fixed applications. A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. Transmitting devices designed to be used by consumers or workers that can be easily re-located, such as wireless devices associated with a personal computer, are considered to be mobile devices if they meet the 20 centimeter separation requirement. A fixed device is defined as a device is physically secured at one location and is not able to be easily moved to another location. Note 2: Any modifications made to the module will void the Grant of Certification, this module is limited to OEM installation only and must not be sold to end-users, end-user has no manual instructions to remove or install the device, only software or operating procedure shall be placed in the end-user operating manual of final products. Note 3: The device must not transmit simultaneously with any other antenna or transmitter. Note 4: To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, Microhard System Inc. shall provide guidance to the host manufacturer for compliance with the Part 15B requirements. Note 5: FCC ID label on the final system must be labeled with Contains FCC ID:

NS912XN58-26 or Contains transmitter module FCC ID: NS912XN58-26. The transmitter module must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the host product. Microhard Systems Inc. is responsible for the compliance of the module in all final hosts. IMPORTANT NOTE REGARDING ANTENNA USE Antenna Use (Point to Multipoint) 2x2 Operation Chain1 Chain2 Dimensions Drawing Microhard Systems Inc Address: 150 Country Hills Landing NW Calgary Alberta Canada Contact Name: Hany Shenouda Tel. No: 403-248-0028 Fax No: 403-248-2762 Email: shenouda@microhardcorp.com For more information, visit www.compex.com.sg