TAPH805 Bluetooth Active Noise Cancelling headphones User Manual

 

Contents 1 Important safety instructions Hearing Safety General information 2 Your Bluetooth on-ear headset What's in the box Other devices Overview of your Bluetooth on-ear tesdaeh 3 Get started Charge your headset Pair the headset with your mobile enohp 4 Use your headset Connect the headset to a Bluetooth device Manage your calls and music Connect to ANC (active noise

)noitalecnac Wear your headphones 5 Technical data 2 2 2 3 3 3 3 4 4 4 5 5 5 6 6 7 6 Notice 8 8 Notice of compliance Declaration of conformity 8 Disposal of your old product and battery 8 skramedarT 7 Frequently asked questions 9 10 EN 1 1 Important safety instructions General information To avoid damage or malfunction:

Caution Do not expose headset to excessive heat Do not drop your headset. Headset shall not be exposed to dripping or splashing. Do not allow your headset to be submerged in water. Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. The integrated battery shall not be exposed to Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Never use your headphones when you are operating a motor vehicle, riding a bicycle, and illegal in many places. About operating and storage temperatures and humidity Operating temperature: 0C (32F) to 40C (104F) Storage temperature: -10C (14F) to 45C (113F) Operating humidity: 8% - 90% RH (No condensation) Storage humidity: 5% - 90% RH (No condensation) Maximum operating altitude: 3000m Battery life may be shorter in high or low temperature conditions. Hearing Safety Danger To avoid hearing damage, limit the time you use headset at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. Listen at reasonable volumes for reasonable periods of time. Be careful not to adjust the volume continuously upwards as your hearing adapts. Do not turn up the volume so high that you can't hear what's around you. You should use caution or temporarily discontinue use in potentially hazard-

ous situations. Excessive sound pressure from earphones and headset can cause hearing loss. Using headset with both ears covered while driving is not recommended and may be illegal in some areas while driving. For your safety, avoid distractions from other potentially dangerous environ-

ments. 2 EN 2 Your Bluetooth on-ear headset Congratulations on your purchase, and product at www.philips.com/welcome. With this Philips wireless on-ear headset, you can:

enjoy convenient wireless handsfree calls;

enjoy and control wireless music;

switch between calls and music. enjoy noise cancelation. What's in the box Philips Bluetooth over-ear headset TAPH802 USB charging cable (for charging only) Other devices A mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset (see 'Technical data' on page 7). Overview of your Bluetooth on-ear headset 1 2 3 4 5 6 7 LED indicator Microphone Micro USB charging slot Active noise canceling (ANC) LED indicator button Volume / Track control button MFB (Music / call control) button Audio cable Quick start guide EN 3 Make sure that the headset are fully charged. Press and hold the button for 2 seconds to turn the headset on. Activate the Bluetooth feature of your mobile phone. For previous device pairing, the device will be paired with the headphone automatically. A voice of

"Device connected" will be heard. For new device pairing, select Philips PH805 on your mobile phone, the device will be paired with the headphone. A voice of

"Device connected" will be heard. For detailed information, refer to the user manual of your mobile phone. The following example shows you how to pair the headset with your mobile phone. Activate the Bluetooth feature of your mobile phone, select Philips PH805. Enter the headset password "0000"

(4 zeros) if prompted. For those mobile phones featuring Bluetooth 3.0 or higher, no need to enter a password. Philips PH805 3 Get started Charge your headset Note charge the battery for one and a half hour for optimum battery capacity and lifetime. Use only the original USB charging cable to avoid any damage. Finish your call before charging the headset, as connecting the headset for charging will power Connect the supplied USB charging cable to:

the micro USB charging slot on the headset and;

the charger/USB port of a computer LED turns white during charging fully charged. Tip Normally, a full charge takes 2 hours. Pair the headset with your mobile phone Before you use the headset with your mobile phone. A successful pairing estab-

lishes a unique encrypted link between the headset and mobile phone. The headset store the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest pained device is replaced by the new one. 4 EN 4 Use your headset Connect the headset to a Bluetooth device Turn on your mobile phone/Bluetooth device. Press and hold the button for 2 seconds to turn the headphones on.

"Device connected" is triggered. The headset are reconnected to the last connected mobile phone/

Bluetooth device automatically. If the last one is not available, the headset try to reconnect to the second last connected device. Tip If your mobile phone/Bluetooth device cannot reconnect automatically, try to reconnect manually by clicking the headphones' name again under the Bluetooth setting manual on your mobile phone/Bluetooth device. To clear the pairing device list on your headset, press the MFB Music /call control) button for more than 10 seconds. Note If the headset fail to connect to any Bluetooth automatically to save the battery life. Manage your calls and music Task Turn the headset on. Button

(

pairing) Operation Press and hold for 2 seconds. Turn the pairing Press and hold for 5 seconds. The white LED is on and fades out. Operation Press once. Press once. Press once. Long press. Long press. Music control Task Play or pause music. Volume up. Volume down. Next track. Previous track. Call control Button MFB (Music/

call control) button Volume/track control Volume/track control Volume/track control Volume/track control Task Pick up/hang up a call. Reject an incoming call Button MFB (Music/call control) button MFB (Music/call control) button Switch caller during a call. MFB (Music/call control) button Operation Press once. 1 beep. Press once. 1 beep. Long press MFB (Music/call control) button Press for three times. 2 beeps Mute/unmute the microphone in a call. Voice control Task Siri/ google voice Button MFB (Music / call control) button Operation Long press EN 5 EN 5 Wear your headphones for every 8 seconds. Indicator Other headset indicator status Headset status The headset are connected to a Bluetooth device, while the headset in standby mode or while you are listening to music. The headset are ready for pairing. and white alternately. The headset are on but not connected to a Bluetooth device. Low battery level. Battery is fully charged. quickly If no connection can be made, the headset will turn itself twice for every 150 seconds until it is out of power Tip After use, twist the headphones for easy storage. 6 EN 5 Technical data Music time (ANC enabled with Bluetooth): 15 hours Talk time (ANC enabled with Bluetooth):

15 hours Standby time (ANC enabled with Bluetooth): 15 hours Normal time for a full charge: 2 hours Rechargeable lithium polymer battery

(530 mAh) Bluetooth 4.2, Bluetooth mono support supported (Advanced Audio Distribution Frequency range: 2.402-2.480GHz Transmitter power: 4dBm Micro-USB port for charging Supports SBC Operating range: Up to 10 meters

(33 feet) Digital echo & noise reduction Low battery warning: available Note EN 7 6 Notice Notice of compliance Notice for US The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interfer-

ence received, including interference that may cause undesired operation. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer-

ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Relocate the receiving antenna. Increase the separation between equipment and receiver Connect the equipment into an outlet on a receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 8 EN environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Notice for Canada:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following Two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3(B)/NMB-3(B) IC Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for uncontrolled environ-

ments. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter Caution: The user is cautioned that changes or responsible for compliance could void the user's authority to operate the equipment. Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of of Conformity on www.p4c.philips.com. Disposal of your old product and battery This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or visit www.recycle. philips.com. This product contains non-removable batteries:

Do not incinerate. Batteries may explode if overheated. For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com. If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headset. Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health. Remove the integrated battery Note Make sure the headset are disconnected from the USB charging cable before removing the battery. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. the battery shall not be exposed to excessive heat such as sunshine, re or the like DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Trademarks Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. EN 9 7 Frequently asked questions be heard. The Bluetooth device is out of range. Reduce the distance between your headset and Bluetooth device, or remove obstacles between them. The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all. Make sure your mobile phone not only supports

(mono) HSP/HFP but also supports A2DP (see

'Technical data' on page 7). I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/ backward). Make sure the Bluetooth audio source supports AVRCP (see 'Technical data' on page 7). For further support, visit www.philips.com/ support. My Bluetooth headset do not switch on. The battery level is low. Charge the headset. I cannot pair my Bluetooth headset with a mobile phone. The Bluetooth is disabled. Enable the Bluetooth feature on your mobile phone and turn on the mobile phone after you turn on the headset. Pairing does not work. Make sure the headset are in pairing mode. Follow the steps described in this user manual. The headset may be connected to a connected device or move it out of range. Pairing may have been reset or the headset have been previously paired with another device. Pair the headset with the mobile phone again as described in the user manual. My Bluetooth headset are connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker. Refer to the user manual of your mobile phone. Select to listen to music through the headset. Voice dialing or redialing does not work on my mobile phone. Your mobile phone may not support this feature. The other side cannot hear me on the mobile phone. The microphone is muted. Press the MFB (Music

/call control) button for three times to enable the microphone. The audio quality is poor and crackling noise can 10 EN Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAPH805_00_EN_v0.2