submitted | available | document details (if available) | source link |
---|---|---|---|
April 11 2019 | April 11 2019 | 39160_Manual_190903 Adobe PDF library 15.00 |
various | User manual | Users Manual | 1.50 MiB | April 11 2019 |
BT500ANC Over Ear Wireless Headphones P/N 39160 User's Manual SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference. Do not expose this device to water or moisture of any kind. Do not use this device while operating a motor vehicle, heavy equipment, walking in traffic, or any other situation in which situational awareness is a key to safety. This device contains a Lithium-ion battery. Dispose of this device only in accordance with local, state, or federal regulations for electronic waste. Charge the battery before rst use and at least once every three months to keep the battery fresh and capable of holding the full charge. Do not allow the battery to fully discharge, as doing so can damage it and reduce its maximum capacity. Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth with warm water. This device has no user serviceable parts. Do not attempt to open, service, or modify this device. 2 INTRODUCTION Thank you for purchasing these BT-500ANC Active Noise Cancelling (ANC) Bluetooth Headphones. These headphones have been designed to provide you with great audio quality, while blocking out ambient noises, such as engines and wind. The BT-500ANC can be used in multiple modes:
Bluetooth with ANC active, Bluetooth without ANC, a wired connection with ANC active, or a full passive wired connection without ANC to conserve battery life. FEATURES Over-the-ear design with Active Noise Cancelling (ANC) circuitry Bluetooth version 5 with support for the A2DP, AVRCP, HFP, and HSP proles Includes the Qualcomm aptX HD audio codec Built-in 500mAh Lithium-ion battery Up to 14 hours of audio playback with Bluetooth and ANC active 40mm drivers with neodymium magnets 100dB sensitivity Audible low battery indicator Up to 30dB of noise cancelling with ANC active 3 CUSTOMER SERVICE The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at support@monoprice.com. Check the website for support times and links. PACKAGE CONTENTS Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement. BT500ANC Over Ear Wireless Headphones 1x 1x Micro USB Charging Cable 1x 3.5mm Audio Cable 1x Carrying Case 1x User's Manual 4 PRODUCT OVERVIEW BATTERY CHARGING Charge the battery before rst use and at least once every three months to keep the battery fresh and capable of holding a full charge. Do not allow the battery to fully discharge, as doing so can damage it and reduce its maximum capacity. 1. When the battery charge gets low, the headphones will say Battery 2. Low and the Bluetooth LED will flash red. If the headphones are powered on, press and hold the Bluetooth Button for 5 seconds to turn them off. 3. Using the included micro USB cable, plug one end into the USB Charge Port on the headphones, then plug the other end into a 5 USB power source. The Bluetooth LED will illuminate solid red while charging is in progress. 4. Battery charging will take about 2 hours for a full charge. Once the battery is fully charged, the Bluetooth LED will change from solid red to solid blue. BLUETOOTH PAIRING Perform the following steps to pair the headphones with a mobile device. Note that these headphones can be paired with up to two devices at the same time. 1. Press and hold the Bluetooth Button for 3 seconds to power the headphones on. The Bluetooth LED will flash blue three times, then will alternately flash red and blue, indicating that they are in Bluetooth pairing mode. 2. Open the Bluetooth settings on your mobile device and search for nearby Bluetooth devices. Locate and select the MP39160 entry. The headphones will say Connected, and the Bluetooth LED will flash blue once every 5 seconds. Notes:
If pairing is not completed within 90 seconds, the headphones will go into standby mode and you will need to repeat the process. To pair a second device, turn off the rst paired device or move it out of Bluetooth range, then repeat the above steps to pair the second device. 6 ACTIVE NOISE CANCELLING To enable Active Noise Cancelling (ANC), slide the ANC Button to the ON position. The ANC LED will illuminate solid green, indicating that ANC is on. To disable ANC, slide the ANC Button to the OFF position. The ANC LED will turn off, indicating that ANC is off. OPERATION Power Press and hold the Bluetooth Button for 3 seconds to turn the headphones on. Press and hold the Bluetooth Button for 5 seconds to turn the headphones off. With the headphones in standby mode, momentarily double press the Bluetooth Button to enable Google Assistant. Audio Playback While listening to audio, momentarily press the Bluetooth Button to pause or resume audio playback. While listening to audio, momentarily press the Volume+/Next Track button to increase the volume level. While listening to audio, momentarily press the Volume-/Previous Track button to decrease the volume level. 7 While listening to audio, press and hold the Volume+/Next Track button for about 1 second to skip ahead to the next track in the playlist. While listening to audio, press and hold the Volume-/Previous Track button for about 1 second to skip back to the previous track in the playlist. Note that your mobile device must support the AVRCP Bluetooth prole to control audio playback from the headphones. Phone Calls If an incoming phone call is received, momentarily press the Bluetooth Button to answer the call. If an incoming phone call is received, press and hold the Bluetooth Button for about 1 second to reject the call. While a phone call is in progress, momentarily press the Bluetooth Button to terminate the call. While a phone call is in progress, momentarily press the Volume+/Next Track button to increase the volume level. While a phone call is in progress, momentarily press the Volume-
/Previous Track button to decrease the volume level. Note that your phone must support the HFP and HSP Bluetooth proles to use the headphones for phone calls and call control. 8 LED INDICATIONS Function LED Indication Power on Power off Pairing mode Pairing successful Audio playback Incoming phone call Call in progress Battery charge low The Bluetooth LED ashes blue three times The Bluetooth LED ashes red two times The Bluetooth LED ashes red and blue alternately The Bluetooth LED ashes blue once every 5 seconds The Bluetooth LED ashes blue once every 5 seconds The Bluetooth LED ashes red The Bluetooth LED ashes blue twice every 3 seconds The Bluetooth LED ashes red every 3 seconds Charging in progress The ANC LED is solid red Charging complete The ANC LED is solid blue ANC active ANC inactive The ANC LED is solid green The ANC LED is off 9 TROUBLESHOOTING Q1: The headphones won't power on. A1: Charge the battery. Q2: The battery won't charge. A2: Ensure that the USB power source is delivering charging power. Conrm that the micro USB charging cable is properly plugged in to the USB Charging Port and the USB power source. Try using a different micro USB cable. Q3: The headphones won't pair with your mobile device. A3: Ensure the headphones and mobile device are within 3 feet of each other. Q4: The headphones won't connect with an already paired device. A4: Ensure that both the headphones and device are powered on. Ensure that your device's Bluetooth is turned on. Q5: There is no sound when playing audio. A5: Ensure that both the headphones and device are powered on. Ensure that your mobile device supports the A2DP Bluetooth prole. Ensure that the volume settings on the headphones and device are set to appropriate levels. Conrm that the audio playback device is set to PLAY. 10 Q6: Sound is distorted when playing audio. A6: Ensure that there are no other nearby devices that use the 2.4GHz band. Ensure that there are no obstructions between the headphones and the audio device. Q7: The hands-free phone controls doesn't work. A7: Ensure that the phone supports the HSP and HFP Bluetooth proles and that they are enabled. Q8: The communications distance is short and/or the sound is garbled. A8: Ensure that there are no other nearby devices that use the 2.4GHz band. Ensure that there are no obstructions between the headphones and the audio device. TECHNICAL SUPPORT Monoprice is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. Technical support is available through the online chat button on our website www.monoprice.com or through email by sending a message to tech@monoprice.com. Check the website for support times and links. 11 SPECIFICATIONS Model Bluetooth Version Bluetooth Chipset Bluetooth Range 39160 5 Qualcomm QCC3031 Up to 32 feet (10 meters) Supported Bluetooth Proles A2DP, AVRCP, HFP, HSP ANC Chipset AMS Noise Reduction with ANC On Up to 30dB Frequency Response 20Hz ~ 20kHz Sensitivity Driver Size 100dB 40mm Supported Audio Codecs Qualcomm aptX HD Battery Capacity 500mAh Audio Playback Time Up to 14 hours with Bluetooth and ANC Charging Time About 2 hours Charging Temperature
+41 ~ +104F (+5 ~ +40C) 12 REGULATORY COMPLIANCE Notice for FCC This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifying the equipment without Monoprice's authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. 13 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radio Notice for FCC Caution This FCC Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modication to said product not expressly approved by Monoprice, including the use of non-approved antennas, could void the users authority to operate this device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice for Industry Canada This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. 14 Radio Notice for Industry Canada Caution This IC RSS-210 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modication to said product not expressly approved by Monoprice, including the use of non-approved antennas, could void the users authority to operate this device. This device complies with IC RSS-210. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Bluetooth word mark and logos are registered trademarks of Bluetooth SIG, Inc. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX, aptX HD, and the aptX logos are trademarks of Qualcomm Technologies International, Ltd. Qualcomm aptX and Qualcomm aptX HD are products of Qualcomm Technologies International, Ltd. Google and Google Assistant are trademarks of Google LLC. 15
This product uses the FCC Data API but is not endorsed or certified by the FCC