89FT7061 2-Way Portable Radio (with Bluetooth, Bluetooth LE and WIFI) C2PC Letter Cover Letter(s)

FCC ID: AZ489FT7061 Date: January 14, 2022 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Class II Permissive Change for PCB and Part Modification and PAG C2PCPX Dear Sir/Madam, With reference to the C2PCPX procedure subject to PAG approval (item C2PCPX in KDB Publication 388624 D02) and KDB inquiry #144531, the application shall meet the following conditions:

1) The requirements of 2.1043 are fulfilled, i.e., devices block functions for the fundamental frequency, primary modulator circuit, maximum power or field strength ratings shall remain unchanged. Overall block diagram maintained no changes to primary modulator circuit, maximum power or field strength ratings. 2) Transmitter PCB layout and parts changes are only permitted if there is no change in the identification of a devices form, functional specification, as initially granted, or previously approved under a Class II permissive change. No change in terms of layout and functional specification. 3) PCB changes are limited to non-substantive modifications layout changes to the same size physical circuit board previously granted. Yes. PCB stack up, form factor and material are maintained. 4) C2PCPX is not permitted to add, remove, augment, or change capabilities, such as transmitters, increased bandwidth, additional rule parts, bands, etc. There are no addition or removal in the transmitter capabilities, bandwidth or rules part. 5) In the PAG submission for item C2PCPX, the applicant shall provide complete information on testing demonstrating that the proposed changes for fundamental emissions are unchanged within the normal acceptable tolerances and out band emissions do not exceed the appropriate limits. The PAG submission shall include all applicable test reports and internal photos. The test reports and internal photos are provided in the application. 6) The modified device shall not be marketed under the existing grant of certification before confirmation that the C2PCPX PAG is approved and granted. Yes. 7) Software Defined Radio (SDR) grants that use the C2PCPX procedure are not permitted to make subsequent Class III permissive changes. Software Defined Radio (SDR) is not used for this application. 8) The C2PCPX PAG procedure has no impact on the provisions of V) of this publication for nonSDR software-only changes, thus adding an equipment class when related to rule changes is still permitted. There is no addition of equipment class. 9) Class I permissive changes are not permitted under this C2PCPX procedure. Yes, Class I permissive changes were not performed ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D FCC ID: AZ489FT7061 Sincerely, ____________________ Arine Lee FCC/IC Certification Manager E-mail : arinelee@motorolasolutions.com ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D FCC ID: AZ489FT7061 Product changes illustration and comparison Description of the changes:

replaced. 1. The changes were triggered due to BT/WLAN chipset part shortage and a new BT/WIFI chipset is 2. Few passive components were replaced at Power Management section (PMIC), BT/WiFi Circuitry, 3.6V Switching Regulator and 3.3V LDO due to new BT/WLAN chipset part design requirement. All replacement parts performance are comparable to the existing parts. 3. Passive and protection components added for UL certification requirement on Audio PA circuit. 4. There is no mechanical change. 5. No change to the sales model number. 6. Reuse shipping batteries, chargers and accessories. 7. No changes to the RF board. ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D FCC ID: AZ489FT7061 Before Changes After Changes RF Board (LMR) No changes RF board without shield (Top) RF board without shield (Top) No changes RF board without shield (Bottom) RF board without shield (Bottom) ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D FCC ID: AZ489FT7061 Voice Controller (VOCON) Board Before Changes After Changes No changes Vocon board PCB layout (Top) Vocon board PCB layout (Top) No changes VOCON board without shield (Top) VOCON board without shield (Top) ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D FCC ID: AZ489FT7061

* Changes are marked in yellow box. Orange box indicates the sections under the shield. Voice Controller (VOCON) Board Before Changes After Changes Controller 3.6V Switching Regulator Vocon board PCB layout (Bottom) Vocon board PCB layout (Bottom) VOCON board without shield (Bottom) VOCON board without shield (Bottom) ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D FCC ID: AZ489FT7061 Expansion Board Before Changes After Changes BT/WLAN Audio PA Circuit Expansion board PCB layout (Top) Expansion board PCB layout (Top) Expansion board without shield (Top) Expansion board without shield (Top) ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D FCC ID: AZ489FT7061 Expansion Board Before Changes After Changes 3.3V LDO Audio PA Circuit PMIC Circuits Expansion board PCB layout (Bottom) BT/WLAN Power Management Circuit Expansion board PCB layout (Bottom) Expansion board without shield (Bottom) Expansion board without shield (Bottom) ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D