submitted | available | document details (if available) | source link |
---|---|---|---|
November 03 2011 | November 03 2011 |
various | User manual 02 | Users Manual | 758.47 KiB | November 03 2011 |
Option for Nedap Luxon wireless light control system The Sensor Bridge is introduced to add commercially available sensors to the Nedap Luxon light control system. Once installed the Sensor Bridge is part of the Senzafil Mesh Network. Sensor data is transferred by this RF network to minimize wiring efforts. Amongst the validated sensors you will find sensors to detect light level, movement or room occupancy. Now it is easy to add sensing capabilities to your Luxon E-series light control system to save more energy. The Luxon Sensor Bridge consists two main parts:
The dome with the RF electronics and microcontroller The base is used for cable connections for power and sensor. Figure 1: Luxon Sensor Bridge, version for surface mounting Powering:
The Sensor Bridge is powered from a mains adapter or similar DC-source supplying 12 to 24V. This voltage is also available for the sensor, so you can choose the supply voltage depending on the voltage needed for the sensor to be used. Power connection via either a standard DC-plug or screw terminals. Option for Nedap Luxon wireless light control system LIGHT SENSOR MAINS ADAPTER NEDAP RF SENSOR BRIDGE MOVEMENT SENSOR Figure 2: Wiring overview for the Luxon Sensor Bridge Compatible sensors:
Many sensor types can be used:
- Switches;
- 1 to 10V dimmers (resistive and electronic potentiometers);
- Light sensors;
- Sensors for detection of movement and / or room occupancy. To select an appropriate sensor that fits your application and your preferences, please use the listing available on our web site www.nedaplightcontrols.com. The Sensor Bridge may only be installed and configured by qualified and trained personnel. For an installation example please see figure 3 below. The Sensor Bridge can be ordered for surface mounting or for recessed mounting; the dome should always point downwards if mounted at approximately the same height as the Senzafil lamp drivers. For recessed mounting, both clamps can be used to secure the unit to a ceiling element. After finishing the connections, the dome shall be secured to the base using four torx screws. After powering the Sensor Bridge it shall be configured using the Senzafil Configuration Tool. From the pick list you can easily select the used sensor with its characteristics. Option for Nedap Luxon wireless light control system HID LAMPS WITH NEDAP LAMP BALLAST SKYLIGHT NEDAP LUXON SENSOR BRIDGE WITH LIGHT SENSOR SKYLIGHT SENSOR DATA FLOW IN SENZAFIL RF MESH NETWORK NEDAP LUXON LIGHT CONTROLLER Figure 3: Installation example for the Sensor Bridge with HID lamps controlled via the Wireless Senzafil Mesh Network in a building with skylights. Option for Nedap Luxon wireless light control system Description Description Description Description Details Details Details Details Supply Voltage 10 to 28VDC Supply current Sensor Bridge: max 100mA, standby < 20mA External sensor: max 200mA Mains adapter 12V / 4W or specification 24V / 6W Dimensions Diameter: 130 mm, Height 70 mm Weight Enclosure protection 0.23kg including cable glands IP67 (the enclosed cable glands must be used properly) IP67 (the en closed cable glands must be used properly) IP67 (the en IP67 (the en closed cable glands must be used properly) closed cable glands must be used properly) Housing colors Base: light gray, top: milky grey-white Connector Safety EMC power: standard DC jack with 2.0 mm centre pin or 2 screw terminals 30-18 AWG, or 0.25 to 1.5 sq.mm. sensor: 3 screw terminals 30-18 AWG, or 0.25 to 1.5 sq.mm. United States and Canada United States and Canada United States and Canada United States and Canada be used that meets the NEC Class 2 requirements shall be used mains adapter shall An UL listed mains adapter An UL listed that meets the NEC Class 2 requirements be used shall mains adapter An UL listed An UL listed mains adapter shall be used that meets the NEC Class 2 requirements that meets the NEC Class 2 requirements The Sensor bridge is designed to meet UL6 The Sensor bridge is designed to meet UL619191919 The Sensor bridge is designed to meet UL6 The Sensor bridge is designed to meet UL6 Europe Europe Europe Europe AnAnAnAn EN60950 compliant mains adapter must be used EN60950 compliant mains adapter must be used EN60950 compliant mains adapter must be used EN60950 compliant mains adapter must be used United States and Canada United States a nd Canada United States a United States a nd Canada nd Canada FCC47 part FCC47 part 15 15 15 15 FCC47 part FCC47 part Europe Europe Europe Europe ENENENEN301301301301 489489489489----1 and 489 1 and 489----3333 1 and 489 1 and 489 EN300 328 EN300 328 EN300 328 EN300 328 Temperature 60C, Storage ----20 to 80C Operating 0 60C, Storage Operating 0 20 to 80C 60C, Storage Operating 0 Operating 0 60C, Storage 20 to 80C 20 to 80C Humidity 25 to 95 % RH. Condensing and icing max 5% of time 25 to 95 % RH. Condensing and icing max 5% of time 25 to 95 % RH. Condensing and icing max 5% of time 25 to 95 % RH. Condensing and icing max 5% of time Luxon Sensor Bridge for surface mounting: 8018669, ordering nr. 9949348 Luxon Sensor Bridge for recessed mounting: 8019037, ordering nr. 9949356 Option for Nedap Luxon wireless light control system FFFFCC Declarations CC Declarations CC Declarations CC Declarations Compliance statement (part 15.19) Compliance statement (part 15.19) Compliance statement (part 15.19) Compliance statement (part 15.19) This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Dclaration Conformit Dclaration Conformit Dclaration Conformit Dclaration Conformit Cet appareil se conforme aux normes RSS exempts de license du Industry Canada. L'opration est soumis aux deux conditions suivantes
(1) cet appareil ne doit causer aucune interfrence, et
(2) cet appareil doit accepter n'importe quelle interfrence, y inclus interfrence qui peut causer une opration non pas voulu de cet appareil. Warning (part 15.21) Warning (part 15.21) Warning (part 15.21) Warning (part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF ERF ERF ERF Exposure (OET Bulletin 65) xposure (OET Bulletin 65) xposure (OET Bulletin 65) xposure (OET Bulletin 65) To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons. Version:
Date:
0.4 20110223
This product uses the FCC Data API but is not endorsed or certified by the FCC