OT-BURN-1 Otbeat burn User Manual

 

burn Quick Start Guide e d i u G t r a t S k c i u Q n r u B t a e b T O Instructions for:

1. Getting Started 2. Downloading the Orangetheory App 3. Charging Device 4. Proper Placement 5. Pairing Device 6. LED Guide 7. Caring for Device 8. Technical Specifications Getting Started:

1. Included in packaging: OTbeat Burn, SM band, LG band, & USB cord 2. Remove OTbeat Burn from packaging 3. Connect USB cord into charging port of device 4. LED light will appear after a few seconds Downloading the Orangetheory App:

*Using your mobile device, download the Orangetheory App. Orangetheory App Note: Fully charge device before attempting to pair for the first time. Page 2 Charging Device:

1. Open rubber port cover on back of device 2. Plug in mini-USB connector into device port 3. Plug in regular USB connector into charging block 4. Plug in charging block into wall outlet

(BACK OF OTBEAT BURN) Optical heart rate sensor LED lights e c i v e D g n i g r a h C

-

n r u B t a e b T O Device can be connected directly to a computer USB port. Note: The voltage differs from wall outlet to computer. Battery is fully charged when Green LED is continuously on During charging: Red LED light will blink slowly LED indication for charging is in front of device Page 3 t n e m e c a l P r e p o r P

-

n r u B t a e b T O Proper Placement:

To transmit accurate data from your device:

1. Fasten device snugly in one of the below placement options 2. Wear device below, and not directly on top, of wrist bone* or elbow 3. The optical sensor on the back should make good contact with skin

*For placement on wrist, measure two fingers above wrist bone

--------------------

--------------------

Elbow

--------------------

--------------------

Wrist bone Page 4 Pairing Device:

1. Once OTbeat Burn is fully charged, press center of splat to power ON the device Event LED light e c i v e D g n i r i a P

-

n r u B t a e b T O Set power ON: Short button press

(Blue LED blinks for 5 seconds) Set power OFF: Long button press

(Red LED light continuously on for 2 seconds then turns off) Page 5 Pairing Device (Cont.):

2. Launch the settings app on your mobile device 3. Ensure your bluetooth settings are on e c i v e D g n i r i a P

-

n r u B t a e b T O OFF ON Page 6 Pairing Device (Cont):

4. Open Orangetheory app on mobile phone. e c i v e D g n i r i a P

-

n r u B t a e b T O Page 7 Pairing Device (Cont.):

5. Use the Orangetheory app to search for device

*Once device appears, OTbeat Burn is successfully connected to app e c i v e D g n i r i a P

-

n r u B t a e b T O Page 8 e d i u G D E L

-

n r u B t a e b T O LED Guide:

Heart Rate Detection LED Indication:

Alternating BLUE and GREEN: Detecting heart rate Alternating BLUE and RED: No heart rate detected Blinking GREEN: Heart rate detected Blinking ORANGE: Heart rate zones are changing Bluetooth Connection State:

Blue LED blinks for 5 seconds: After turning on the unit Blue LED continuously on for 5 second: Connected Green LED on for 2 seconds: Connected (HR not detected) Green LED continuously on: Updating firmware Battery LED Light During Charging:

Red LED blinks slowly: Charging Green LED continuously on: Battery full Battery State:

Red LED blinks three times: Low battery at <15% (repeat every 5 min. until reach critical level) Red LED continuously on for 2 sec: Device powering off Page 9 e c i v e D r o f g n i r a C

-

n r u B t a e b T O Caring for Device:

1. To ensure accurate readings, clean the sensor lens with a soft cloth 2. OTbeat Burn unit and strap are waterproof to IP67 specifications and can be easily cleaned with mild soap and cool water 3. Use a cotton swab and only rubbing alcohol to clean the USB charging contacts when necessary: do not contact USB charging port 4. Do not use any abrasive chemicals to clean the Otbeat Burn unit, sensor, or strap. This will cause permanent damage Page 10 Technical Specifications:

Feature Functions Heart Rate Range Heart Rate Accuracy Transmission Power Supply ANT+ or BLE Transmission Distance Battery Life time

(PPG&BLE always on) Water Resistance Level Description heart rate detection and transmission

(ANT+ or Bluetooth 4.0), battery low alert 30 to 220 BPM in 1 BPM resolution

+/-5 BPM ANT+ /BLE 3.8V Li-ion Polymer rechargeable battery 15 Meters Up to 24 hours of continuous detection IP67 Storage Temperature Operating Temperature Memory capacity

-20 to +60C 0 to +40C 6 hours detection s n o i t a c i c e p S l a c i n h c e T

-

n r u B t a e b T O Page 11 For more information visit orangetheoryfitness.com/otbeat burn

(brand)

(version) OT A0

(date)

(Company Model)

(design content) 2018-5-8 FD063

(order number)

(Customer model) GM18167 OTbeat

(Part No) 17.03.09.00130

(electronics engineer)

(software engineer)

(structural engineer)

(Designers)

(Review)

(standardization)

(project manager)

(Sales)

(approve) SIZE MATERIAL PRINT Process requirements 172*86mm86*86mm 70g