| submitted | available | document details (if available) | source link |
|---|---|---|---|
| various | User Manual 01.22 | Users Manual | 349.78 KiB |
X20 QUICK START GUIDE P2 MOBILE TECHNOLOGIES LIMITED 1 SmartMoment Quick Start Guide 1.1 Overview SmartMoment (Lightweight Mode) is a built-in network setup tools and virtual controller designed to streamline the process of setting-up a Wi-Fi network. 1.2 Purpose The lightweight mode allows you to:
Set up a basic network with just three steps Configure IP address, netmask, gateway, DNS, SSID and password Have a quick overview of AP and client device 1.3 Connection Method 1. Wireless
-
- Use mobile device to connect to the SSID P2MTwifi with password Power up the AP. p2mtuser. Power up the AP. Connect the AP and the PC with a LAN cable. Set the IP of the PC to 192.168.1.2
- Open the browser and type the IP address 172.16.0.1.
- Navigate to the top menu bar and click Lightweight under Mode. 2. Wired
-
-
-
- Navigate to SmartMoment by 192.168.1.1 3. Default Login Information Username: p2mtadmin Password: p2mtadmin 1.4 Note SmartMoment Lightweight mode is for basic configuration ONLY. Use the advance mode for advanced setting. For details, please refer to the SmartMoment User Guide. Copyright 2015. P2 Mobile Technologies Limited. All rights reserved. Website: www.p2mt.com Email: support@p2mt.com Tel: (+852) 3905 1880 Fax: (+852) 3695 0820 2 Explanation of Ports 1. Ports &
Connectors Quantity & Specifications LAN Port 2. LED 10/100/1000M Base-T Ethernet port (RJ-45), used as a WAN port and used for being powered by PoE function. LED RUN StateColour Indication SteadyGreen AP is ready. Off No power to AP. LAN SteadyGreen 1000Mbps Off Flashing Ethernet link negotiated. Ethernet link activity. Ethernet link unavailable. Integrated 5 GHz radio is enabled. Integrated 5 GHz radio is disabled. External 5 GHz radio is enabled. External 5 GHz radio is disabled. Note: AP that is not set up according to the instructions in the user Integrated 5 GHz Radio Status External 5 GHz Radio Status SteadyGreen SteadyGreen Radio Radio Off Off 0 1 Function AP Power
/ Ready Status Network Link Status Copyright 2015. P2 Mobile Technologies Limited. All rights reserved. Website: www.p2mt.com Email: support@p2mt.com Tel: (+852) 3905 1880 Fax: (+852) 3695 0820 manual may malfunction. the actual environment. The connection quality of the AP and Wi-Fi coverage vary with Only use the mounting kits that is compatible with the AP. Please refer to the network plan provided. Without adhering to the network plan may result in a network failure. For the best practice, please consult P2MT authorized engineers. 3 Mounting 3.1 Pole Mounting Procedure(Pole Size: 40-52mm) 1. Firstly install the L shaped clamp, with M6 screw nut, spring washer and flat washer. Four screws need be installed. 2. Put the U shaped screw stem and U shaped slot into the hole. And then drive the M6 crew nut and M6 washer. Install the clamp on the back of the AP, with M6*12 screw bolt, M6 spring washer and M6 flat washer. Four screw bolts need be installed. Input M6*12 screw bolt and M6 washer into the hole on the back and drive them. 5. Finally mount the AP on the pole as shown in the picture. And drive the screw nut tight with wrench. 3. 4.
-End of Quick Start Guide-
Copyright 2015. P2 Mobile Technologies Limited. All rights reserved. Website: www.p2mt.com Email: support@p2mt.com Tel: (+852) 3905 1880 Fax: (+852) 3695 0820 Increase the separation between the equipment and receiver. Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. to provide a separation distance of at least 141.59cm
This product uses the FCC Data API but is not endorsed or certified by the FCC