A60 Smart Mini Payment Terminal User manual

A60 Smart Mini Payment Terminal 1. Contents Checklist Please check the components after unpacking. If any one of them is missing, or if there is a page missing from the product manual,ect.,please contact the dealer. Name Qty. 1 1 1 1 1 Smart Mini Payment Terminal AC Power Adapter Battery Cable Product Manual 2. Installation USB port: Connect USB device or PC. SAM/SIM card:

1 Open the battery cover on the Top of the terminal;

2 Take out the battery;

3 Insert SAM/SIM card into the corresponding SAM/SIM card slot. Micro SD card:

1 Open the battery cover on the Top of the terminal;

2 Take out battery;

3 Insert Micro SD card into the corresponding Micro SD card slot. 3. Instruction 1 Power ON/OFF Power on: press and hold the Power button for five seconds until LCD backlight light, the terminal turns on successfully. Power off: press and hold the Power button for three seconds until the shutdown menu appears, tap Shutdown > Click Shutdown, and then Shutting appears, the terminal is being turned off. 2 IC card & Magnetic Stripe Card Put IC card chip side upward and the magnetic stripe face down, then push-in Card slot of bottom. Please push -out the card with a steady speed. 3) Battery charging User can charge the battery with power adapter, and the charging status will be displayed on the LCD. 6Swiping contactless card Place a contactless card close to the sensor area of swiping which is at the top of the terminal. 4. Installation and Usage Tips 1Avoid putting the terminal in direct sunlight, high temperature, moist, or dusty environment. 2Forbid non-professional to repair the terminal. 3Before insert the card, please check internal and around of IC card slot. when you found some suspicious objects , must report to related administrator. 5. Lithium Ion Battery Usage Tips WARNING:

1Don't use the battery in sunlight or smoke, dust environment. 2Prohibited to strike, squeeze and tread on battery or throw it into the liquid and fire. 3If battery is impressive, deformed, damaged or exothermic seriously, please stop using immediately and replace it!

4If the continuous working time is only half of new one, the battery life may be end. Please replace it!

5Must use the specified battery model and charger, otherwise there will be explosion 6Charging time can not exceed 24 hours. If the battery is out of power, please recharge in time. Avoid damaging the battery in over-charge and over-discharge. 7If be non-use for long time, please recharge the battery per 6 months to avoid shortening its life. 8Suggest to replace it when the battery have been used for 2 years. 9Be sure to follow the instructions to dispose the wasted batteries. Icon shows Do not throw away, need professional recycling. Class II Equipment For indoor use only Energy Efficiency Marking AC voltage DC voltage The MAINS plug is used as the disconnected device. FCC Regulations:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands, and placed in positions that simulate RF exposure in usage near the body. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: V5PA60 For this device, the highest reported SAR value for usage near the body is 1.39W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. ISED Notice This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le et Dveloppementconomique Canada applicables aux appareils radio exempts de licence. prsentappareilestconforme Innovation, Sciences CNR aux L'exploitationestautorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareildoit accepter tout brouillageradiolectriquesubi, mmesi le brouillageest susceptible d'en IC: 11689A-A60 ISED Radiation Exposure Statement limitesd'exposition DAS aux la norme CNR-102 science de This EUT is in compliance with SAR for general population/uncontrolled exposure limits in ISED RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Cetappareilestconforme la populationgnrale de le dveloppementconomique Canadaet a ttestenconformit avecles mthodes de mesure et procduresspcifiesdans IEC 62209.Cetappareil et saousesantennes ne doiventpas treco-localissoufonctionnerenconjonction avec tout autreantenneoutransmetteur. PAX TECHNOLOGY LIMITED To know more product details, please visit http://www.pax.com.cn pour linnovation et IEEE 1528 et incontrle