BP60A Multifunction Printing Base User Manual

BP60AMultifunction Printing BaseProduct Instruction PAX Computer TechnologyShenzhenCo., Ltd. 1. Appearance Instruction Front Charging Contact Back Rubber Foot Rubber Foot Rubber Foot SNBar Code NameplateLaser Etching Rubber Foot LAN USB1 RS232 POWER USB2 The matching diagram for A60 host and intelligent printer base is as follows:

2. Installation Instruction 1Connect the base's DC port with a 9V/1A power adapter. 2 Use a network cable to connect the base's LAN port with a gateway device that can access the Internet, such as router, LAN switch. (If not used, do not install.) 3Put the paper roll (width: 58mm, diameter: 80 mm) into the paper storehouse. 3. Usage Instruction 1. Place A60 host (by pushing from bottom to top) on the base. Then A60 host will identify the base automatically, and switch to be charged through the base. 2. When the base's Ethernet connection is available, the A60 host will automatically switch the data connection to the Ethernet connection on the base. 3. It is supported that multiple A60 hosts are connected to the base printer through Bluetooth, and bills will be printed one by one. Note: When using the Ethernet, do not vibrate the base and A60 host violently, so as to avoid the interruption of the data connection between the host and the base. 4. Terminal Specifications Power supplyDC-9V@1A Ethernet10/100Mbps adaptive network port RS-232 serial port: Maximum transfer rate115200bps USB portUSB2.0 HOST Port Instruction:

DC port x 1: Power port TYPE AUSB x 2:USB2.0 Host port, used to connect the scanner gun or keyboard RS-232serial port x 1 : RJ45-8P8C Relative humidity: 1096Non-condensing Ethernet x 1 :RJ45-8P8C Working Environment: Working temperature050 Storage Environment: Storage temperature: -2070 Dimensions162mm * 119.0mm * 146.3mmLength x width x height Weight550g 5. Precautions for Use and Installation Relative humidity: 596Non-condensing 1Do not damage the power adapter. Otherwise, they can't be used again. 2Before connecting the power supply to the AC outlet, check whether the power supply of the socket is in compliance with the device specified voltage. 3Make sure the base is switched on when connecting it to the power supply. 4Avoid exposing the machine in sunshiny, hot, humid, or dusty environment. 5Keep the machine away from liquid. 6Do not insert foreign objects into any port of the device, which may damage the device. 7Please contact the special maintenance personnel when the device fails. The user is not allowed to repair the device without authorization. 8It is strictly forbidden to disassemble the machine in explosive dangerous places and use external interfaces. 9Do not use wet cloth to clean the product. 10You can operate the device only after being guided by the professional. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Radiation Exposure Statement:

This equipment complies with FCCs RF radiation exposure limits for general population without SAR evaluation. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.