PX5RF Multi-Lane Payment Terminal User manual

PAX TECHNOLOGY INC. Product Description Product Description Stylus pen Touch screen and Contactless reader area Magnetic stripe reader Privacy shield Keypad Smart card reader PAX TECHNOLOGY INC. Communication Module Communication Module Power Connections Power Connections Cable retention cover plate xP terminals that include a default communication module come standard with one Ethernet port and RS232, USB, and PUSB network capabilities. However, if the default communication module is replaced with an optional communication module, your choice of these additional network capabilities are available:

A second Ethernet port Power over Ethernet An Ethernet hub The commu nication module is located on the underside of the terminal. Wi-Fi and Bluetooth LE Wi-Fi and Cellular GSM Communication ports - located under cover plate Speakers Regulatory label Part number/

serial number label Communication module MAC address label Communication ports are labeled and color-coded:

Communication module White Red Yellow Black Blue Green WARNING:

Power down and remove all power from the terminal before removing or installing a communication module. A communication module must be installed before power can be applied to the terminal. x 3 Power can be supplied via the power port or a single data cable that carries power. This power can be provided via a powered cable where the connected POS terminal provides the power

(i.e. PUSB or Power over Ethernet) or by connecting a P power supply directly to the data cable (i.e. RS232 or USB). 1) Power Port Insert the power connector into the green POWER port. Turn the power connector, locking the tab behind the short plastic wall. Dress the cable through the retention clips. A separate data cable is also required. 2) POS Cable Insert the cable connector into the appropriate port on the terminal. Dress the cable through the retention clips opposite the port. Connect power supply to cable as required. The cash register could also supply power to terminal. 3) Power over Ethernet (PoE) Power is available over the red LAN1 port when the optional PoE communication module is installed. Cable Retention Cover Plate After power and data cables are connected and dressed through retention clips, install the cable retention cover plate and secure with captive screw. Screw Working Environment: Temperature -10C50C (14F122F) R.H.: 10%93% (non-condensing) Storage Environment: Temperature -20C60C (-4F140F) R.H.: 5%95% (non-condensing) PAX TECHNOLOGY INC. Stylus Holder and Pen Stylus Holder and Pen PlugsPlugs 4 1) Mounting Locations 2)Stylus Port 3) Retention Clips Privacy Shield Privacy Shield 1) Align stylus holder over metal screw openings at left side or top of terminal. Insert tabs into indentations along edge. Attach with captive screws. 2) Insert connector end of stylus pen into stylus port on left side of terminal. 3) Use enclosed plastic card to press stylus cord into retention clips on left side of terminal. 5 Insert tabs and snap shield firmly in place to left and right of keypad. Not designed to be removable. Removing the shield breaks the retention tabs and the ability to remotely track the status of the shield is lost. Decorative Plug If a privacy shield is not installed, a non-removable decorative plug may be installed in its place. This plug does not provide any PIN entry privacy. CAUTION: If the privacy shield is not installed, you must use PCI-approved alternative methods to secure the PIN pad. 1Privacy Shield Decorative Plug 1) Stylus Holder Plug 6 1) Stylus Holder Plug If required, to prevent stylus pen from being inserted vertically into stylus holder, firmly insert plug into opening in holder, aligning with curve of stylus holder. 2) Smart Card Reader Plug If required, insert smart card reader plug into smart card receptacle slot. To remove, if required, gently pry out the plug using a small screwdriver in the slit along top of plug. 3) Ethernet Plug An Ethernet plug is included in case you want to block an inactive LAN port. Align plug so that it matches the shape of the port and gently push into opening. To remove, if required, gently pry off using a small screwdriver in the slit along the top of the plug. Note: LAN2 port is enabled only when Ethernet hub or PoE and Ethernet hub communication module is installed. 3) Ethernet Plug 2) Smart Card Reader Plug PAX TECHNOLOGY INC. Reset Button and Audio Jack Reset Button and Audio Jack Stand Installation Stand Installation 7 If required, restart the terminal by pressing in and holding the reset button for 2-3 seconds Audio Jack Reset Button Stylus Port If required, a visually disabled person can connect a headphone to the terminal for audio prompting using the 3.5mm output audio jack. Cable Lock Cable Lock 8 If required, insert customer-provided cable lock into K-Slot. Loop cable around permanent object to secure in place. 9 x If required, the P terminal may be mounted to a stand. Instructions may vary depending on stand specifications. Route Cables Carefully route the required cables up through the stand pipe and out the top. Connect the cables to the xP terminal ports. Insert the three mounting slots on the underside of the terminal into the three metal prongs on the stand base. Slide the terminal firmly into position, locking the terminal in place on the stand. Secure with fastening screw or locking device as required. Mounting Slots P/N:200312000000224 This document is provided to you for informational purposes only. All features and specifications are subject to change without notice. PAX's name and PAX's logo are registered trademarks of PAX Technology Inc. All rights reserved. PAX TECHNOLOGY INC. Cleaning the Device Cleaning the Device 10 WARNING:

Do not use industrial strength or abrasive cleaner as it may damage or scratch the screen. Do not immerse device in water (or liquid.) Do not spray water or cleaner into the MSR slot, Smart Card Reader or ports. To clean screen, apply distilled water or mild glass cleaner onto a soft, lint-free cloth and gently wipe terminal screen. To clean terminal, apply distilled water or plastic-safe cleaner onto a soft, lint-free cloth and gently wipe terminal. Available Accessories Available Accessories 11 ISED Notice This device complies with Innovation,Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1) this device may not cause interference,and 2) this device must accept any interference,including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

1) l'appareil ne doit pas produire de brouillage,et 2) l'utilisateur de l'appareildoit accepter tout brouillageradiolectriquesubi, mmesi le brouillageest susceptible d'en This Class B digital apparatus complies with Canadian ICES-003. Cetappareilnumrique de la classe B estconforme la norme NMB-003 du Canada. IC: 11689A-PX5RF Power Supply 200310110000070 Requires Power Cord Power Cord 200311020000023 Requires Power Supply Stylus Pen 200209090000929 Stylus Holder Plug 200209090000930 ISED Radiation Exposure Statement This EUT is very low power and compliance withRSS-102 exemption requirements. Ce MAE esttrsfaible puissance et de la conformit aux exigencesd'exemptionCNR-102. PAX Technology Inc. 4901 Belfort Road, Suite 130 Jacksonville, FL 32256, USA T: 877-859-0099 W: www.pax.us E: sales@pax.us RS232 Cable 200204020000140 Requires Power Supply USB Cable 200204020000141 Requires Power Supply Privacy Shield 200209060000040 9 10 Decorative Privacy Shield Plug 2002090900001037 FCC Note:

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure Information This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment is to be connected only to PoE network without routing to the outside plant FCC Regulations:

This mobile phone complies with part 15 of the FCC Rules.

(1) Operation is subject to the following two conditions:

This device maynot cause harmful interference,and

(2) thisdevice must accept any interference received, including interference that maycause undesired operation. This mobile phone has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiated radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. PAX TECHNOLOGY INC.