| submitted | available | document details (if available) | source link |
|---|---|---|---|
| September 09 2014 | August 03 2015 |
| various | 08 user guide | Users Manual | 1.53 MiB | September 09 2014 / August 03 2015 |
User manual LTE-NAD V1140-xxx Peiker product ID:
Revision:
Date:
Status:
2189-140-xxx-00 (V1140-xxx) 0.10 August 2014 Draft _______________________________________________________________________________________________________________ Seite 1 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe History:
Date 15.09.2013 0.5 13.12.2013 0.6 16.12.2013 0.7 01.04.2014 0.8 17.06.2014 0.9 24.06.2014 0.9.1 31.07.2014 0.10 08.08.2014 0.11 Revision Name Comment wlo phse Initial document Some additions to sections 2.1 and 3.3 Some corrections to section 2.2, Figure 4 updated Some additions to section 8 phse phse Modifications/additions to section 8 phse wlo phse phse Modifications/additions to sections 8.1, 8.1.1 and 8.2 Updated Max Antenna Gain Values in section 8.3 Added FW update and WIN7 driver installation Added FCC labeling requirements of V1140-100 _______________________________________________________________________________________________________________ Seite 2 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Content 1 Introduction .......................................................................................................................................... 5 1.1 Scope .................................................................................................................................................. 5 1.2 Audience ............................................................................................................................................ 5 1.3 Contact information, Support ......................................................................................................... 5 1.4 Related Documents .......................................................................................................................... 5 2 Overview ............................................................................................................................................... 6 2.1 Product Variants................................................................................................................................ 6 2.2 Features ............................................................................................................................................. 7 2.3 Approvals ........................................................................................................................................... 7 3 Overview ............................................................................................................................................... 8 3.1 HW Features ...................................................................................................................................... 8 3.2 Connectors ......................................................................................................................................... 8 3.2.1 Module Signal and RF Connectors .......................................................................................... 8 3.2.2 Ground and Heat Dissipation Connectors.............................................................................. 8 3.3 Main Interfaces ................................................................................................................................. 8 3.3.1 USB .............................................................................................................................................. 8 3.3.2 SIM Interface ............................................................................................................................. 9 3.3.3 Power on ..................................................................................................................................... 9 3.3.4 Reset ........................................................................................................................................... 9 3.3.5 GPIOs .......................................................................................................................................... 9 3.3.6 GSBIs ......................................................................................................................................... 10 3.3.7 Module Pin-out ......................................................................................................................... 11 3.4 Supply Voltage ................................................................................................................................ 15 3.5 Power Consumption ....................................................................................................................... 15 3.6 Transmitter ...................................................................................................................................... 16 3.7 Receiver ........................................................................................................................................... 16 3.8 Environmental Specification .......................................................................................................... 16 3.8.1 Temperature Range ................................................................................................................ 16 Evaluation Kit ..................................................................................................................................... 17 4.1 Overview ...................................................................................................................................... 17 4.2 Firmware Update ........................................................................................................................ 21 4.2.1 Identify Qualcomm Diagnostics Port Number ..................................................................... 21 4.2.2 Install and Run FW Executable ............................................................................................. 21 4.2.3 Known Issues ........................................................................................................................... 22 4.3 Windows 7 Driver Installation ................................................................................................... 23 4.3.1 Driver installation................................................................................................................. 23 4.3.2 Available interfaces ............................................................................................................. 23 4.3.3 AT Command interface and PPP Dial-up Modem connection ....................................... 23 4.3.4 RmNet NDIS connection as Network Interface Card ..................................................... 25 4.3.5 Diagnostics interface ........................................................................................................... 26 4.3.6 NMEA GNSS interface ......................................................................................................... 26 AT Command Set ............................................................................................................................... 26 Safety Recommendations according to EN60950-1 ..................................................................... 28 List of Acronyms ................................................................................................................................ 29 5 6 7 4 _______________________________________________________________________________________________________________ Seite 3 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 8 Regulatory Certifications .................................................................................................................. 30 8.1 USA (FCC) ........................................................................................................................................ 30 _______________________________________________________________________________________________________________ Seite 4 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 1 Introduction 1.1 Scope This document gives an overview about electrical, mechanical and functional detail of the peiker LTE-
NAD v1140-xxx. 1.2 Audience Information to integrate the module in other applications. 1.3 Contact information, Support peiker acustic GmbH & Co KG Max-Planck Street 32 D-61381 Friedrichsdorf / Ts. Germany http://www.peiker.de info@peiker.de 1.4 Related Documents None. _______________________________________________________________________________________________________________ Seite 5 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2 Overview 2.1 Product Variants The LTE-NAD is available in multiple product variants:
Peiker product #
2189-140-100-00 (V1140-100) 2189-140-101-00 (V1140-101) 2189-140-103-00 (V1140-103) 2189-140-104-00 (V1140-104) 2189-140-105-00 (V1140-105) 2189-140-106-00 (V1140-106) All variants include Quad band GSM/GPRS/EDGE (850, 900, 1800, 1900 MHz) V1140-100 Module configuration LTE EU configuration LTE North America configuration 2G/3G EU/RoW configuration LTE Asia Pacific configuration 2G/3G North America configuration 2G/3G China configuration LTE Bands WCDMA Bands B3, B7, B20 FDD1, FDD8 V1140-101 LTE Bands WCDMA Bands B2, B4, B5, B17 FDD2, FDD5 V1140-103 LTE Bands WCDMA Bands V1140-104 LTE Bands WCDMA Bands V1140-105 No LTE support FDD1, FDD2, FDD5, FDD6, FDD8 B1, B3, B5, B7, B19 FDD1, FDD5, FDD6, FDD8 LTE Bands WCDMA Bands No LTE support FDD2, FDD5 V1140-106 LTE Bands WCDMA Bands No LTE support FDD1 _______________________________________________________________________________________________________________ Seite 6 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 2.2 Features Features
- Same footprint and pin-out for all modules
- Voice and data calls are supported in all modules
- GSM (R99, GPRS and EDGE) for all modules
- WCDMA (R99, R5 HSDPA, R6 HSUPA and R7 HSPA+) for all modules
- WCDMA (R8 DC-HSPA+) for all modules except for V1140-101 and V1140-105
- LTE (Rel.9 Cat3 FDD) for LTE capable modules
- DTM/eDTM
- eCall inband modem
- Standalone GPS, GLONASS, AGPS (MS-Assisted and MS-Based) Data rates
- GSM: DL/UL 14.4kbps / 14.4kbps GPRS: Multislot class 12, DL/UL 85.6kbps / 42.8kbps EDGE: Multislot class 12, DL/UL 236.8kbps / 118.4kbps
- WCDMA: DL/UL up to 384kbps HSPA+:
Category 24 in DL using 64 QAM and Dual-Cell; Up to 42 Mbps Not supported by V1140-101 and V1140-105 Category 14 in DL using 64 QAM; Up to 21 Mbps Category 6 in UL using 16 QAM; Up to 5.76 Mbps
- LTE-FDD Category 3: Up to 100 Mbps in DL, up to 50 Mbps in UL Power Classes
- LTE: All supported bands, Power Class 3
- WCDMA: All supported bands, Power Class 3
- EDGE: 850 MHz / 900 MHz / 1800 MHz/ 1900MHz, Power Class E2
- GSM / GPRS: 850 MHz / 900MHz, Power Class 4
- GSM / GPRS: 1800 MHz / 1900MHz, Power Class 1 Dimension and Weight
- Dimensions: 31mm x 46mm x 4mm
- Weight < 10 grams 2.3 Approvals
- R&TTE directive
- CE, GCF
- FCC, IC, PTCRB
- AT&T _______________________________________________________________________________________________________________ Seite 7 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 3 Overview 3.1 HW Features
- Qualcomm SoC (system on chip) o LTE capable modules V1140-100, V1140-101 and V1140-104 MDM9215 Baseband / PMIC8018 Power management / WTR1605L o Non-LTE modules V1140-103, V1140-105 and V1140-106 MDM8215 Baseband / PMIC8018 Power management / WTR1605
- Cortex A5 Core up to 550 MHz
- 3 DSPs for modem and low power audio sub systems
- RPM Resource and power manager
- 2Gb NAND Flash x16,
- 2Gb Low Power Mobile DDR SDRAM x32
- 19.2MHz clock reference
- Dedicated heat sink in center area underneath the PCB
- GPS/GLONASS operation, GPS antenna biasing and diagnostics 3.2 Connectors 3.2.1 Module Signal and RF Connectors The LTE-NAD has 172 signal pins (2xAA and 2xBB) connector pads with 1.0mm pitch. The signal pads are located close to the board edges. There are three antenna pads, each collocated by RF GND connectors
- Main transmit and receive antenna pin LGA_PRX_ANT
- Diversity antenna for WCDMA respective MIMO antenna for LTE pin LGA_DRX_ANT_IN
- GNSS antenna for both GPS and GLONASS pin LGA_GPS_DRX_ANT 3.2.2 Ground and Heat Dissipation Connectors To support the usage of module under complicated thermal conditions, there are a number of large grounded pads in the center of PCB. These pads are dedicated ground pads to transfer heat dissipation to a carrier board. This should be especially considered by customer designs. A reference design showing landing patterns and PCB stack-up is available on request. 3.3 Main Interfaces 3.3.1 USB The NAD has one USB2.0 OTG high speed (480MBit) compliant interface including the PHY. The IF consists of 5 signals:
_______________________________________________________________________________________________________________ Seite 8 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe USB Data Plus signal
- USB_D_P:
- USB_D_M:
USB Data Minus signal Master/Slave Configuration1
- USB_ID:
- USB_VBUS:
USB Voltage Supply
- VREG_USB3_3V075 USB Voltage Output A dynamic reconfiguration between USB-Host or USB-Device is not foreseen, the NAD can be configured to USB-Host or USB-Device by the insertion of a resistor on the USB_ID line. 3.3.2 SIM Interface The NADs SIM interface is compatible to 1.8V and 3V SIM Cards, the necessary voltage and level shifting is handle by LTE-NAD automatically. The IF consists of the following signals:
VREG_USIM USIM_CLK USIM_DATA USIM_RESET The data speed on the SIM IF is up to 4 Mbps, so HW designers should take care of the length and routing of the SIM IF to prevent potential EMC problems. 3.3.3 Power on The signal PON_N is used switch on the NAD-Module. PON_N is pulled against VMAIN on the LTE-NAD internally. Due to this fact it is recommended to pull this input against GND using an open collector or open drain output only. 3.3.4 Reset EXT_RESIN_N is used to reset the LTE-NAD-Module, see table of LTE-NAD signal pins. There are further reset signals available, please check . RES_IN is pulled against VMAIN power on the LTE-NAD internally. Therefore, it is recommended to pull this input against GND using an open collector or open drain output only. 3.3.5 GPIOs 1 The LTE-NAD is configured in the slave mode. For other configuration of the USB Interface please contact peiker acustic GmbH & Co.KG. _______________________________________________________________________________________________________________ Seite 9 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe There are 51 GPIOs on the LTE-NAD module available. Most of them are part of the 5 GSBIs provided in next chapter. They are used for different interfaces (see Table 1 and the following chapters). For allocation of GPIOs/GSBIs to different configurations please contact peiker acustics GmbH & Co.KG GPIOs and GSBIs share the same output pins and may not available when used as GSBI configuration. The following GPIOs are not belonging to a GSBI bundle:
GPIO 47, 72, 82, 25, 28, 26, 27, 84, 80, 21, 23, 22, 24, 20, 1, 78, 79, 85, 86, 69, 0, 77, 65, 61, 68, 51, 54, 73, 48, 49, 53. The following GPIOs are belonging to a GSBI bundle:
GPIO 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 29, 30. 3.3.6 GSBIs Each GSBI (General Serial Bus Interface) consists of a bundle of 4 GPIOs. 5 GSBI are available. The reference voltage is of the GSBIs is 1.8V. Available signals on GSBI bundles at the board to board connector:
- GSBI1: GSBI1_0, GSBI1_1, GSBI1_2, GSBI1_3 (GPIO_29, 30, 2, 3)
- GSBI2: GSBI2_0, GSBI2_1, GSBI2_2, GSBI2_3 (GPIO_4, 5, 6, 7)
- GSBI3: GSBI3_0, GSBI3_1, GSBI3_2, GSBI3_3 (GPIO_8, 9, 10, 11)
- GSBI4: GSBI4_0, GSBI4_1, GSBI4_2, GSBI4_3 (GPIO_12, 13, 14, 15)
- GSBI5: GSBI5_0, GSBI5_1, GSBI5_2, GSBI5_3 (GPIO_16, 17, 18, 19) For the standard configuration of the GSBIs see the following Fehler! Verweisquelle konnte nicht gefunden werden. 3. _______________________________________________________________________________________________________________ Seite 10 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 1 V1140-xxx General Serial Bus Interface GSBI interface configuration 3.3.7 Module Pin-out Table 1 PIN Module Pin-out Signal 1 GND 2 22 GND 23 24 25 26 27 28 GPIO47 JTAG_TDI JTAG_TDO GPIO_72 JTAGTMS JTAG_TRST_N Direction related to LTE-NAD Input Power Input Power Input Input Output IN/OUT Input Input Comment Main ground connection, Corner pad Main ground connection WDOG_DISABLE JTAG Interface JTAG Interface JTAG Interface JTAG Interface _______________________________________________________________________________________________________________ Seite 11 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe PIN Signal 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 JTAG_RTCK GND JTAG_TCK JTAG_RESOUT_N GPIO82 JTAG_PS_HOLD EXT_RESIN_N GND RESOUT_N GPIO29_ SDC2_CMD GPIO25_ SDC2_D0 GPIO28_ SDC2_D3 GPIO30_ SDC2_CLK GND GPIO26_ SDC2_D1 GPIO27_ SDC2_D2 PM_GPIO4 GPIO84 GND SDC1_CMD SDC1_DATA0 SDC1_DATA3 SDC1_CLK GPIO80_SDC1_DET_N GND SDC1_DATA2 SDC1_DATA1 GPIO21_ I2S_WS GPIO23_ I2S_DOUT GPIO22_ I2S_DIN GPIO24_ I2S_MCLK GND GPIO20_ I2S_CLK GPIO19_GSBI5_3 GPIO17_GSBI5_1 GPIO18_GSBI5_2 GPIO15_GSBI4_3 GND USB_D_P USB_D_M GND GPIO14_GSBI4_2 Direction related to LTE-NAD Output Input Power Input Input Output Input Input Input Power Output IN/OUT IN/OUT IN/OUT Output Input Power IN/OUT IN/OUT IN/OUT Output Input Power IN/OUT IN/OUT IN/OUT Output IN/OUT Input Power IN/OUT IN/OUT Output Output Input Output Input Power Output Output IN/OUT Input Output Input Power IN/OUT IN/OUT Input Power Input Comment JTAG Interface Main ground connection JTAG Interface JTAG Interface NAD Runnig, Controll signal JTAG Interface Input Reset for LTE-NAD module Main ground connection Output Reset SD Card CMD SD Card Data 0 SD Card Data 3 SD Card Clock Main ground connection SD Card Data 1 SD Card Data 2 Reset of the Codec Main ground connection SD Card CMD SD Card Data 0 SD Card Data 3 SD Card Clock Main ground connection, Corner pad SD Card Data 2 SD Card Data 1 IS - Word Select IS Data Output IS - Data Input IS - Master Clock Main ground connection IS - Clock 2 Pin UART TXD 3 IC Serial Data 2 Pin UART RXD 3 4 Pin UART TXD 1 Main ground connection High Speed USB Device for communication High Speed USB Device for communication Main ground connection 4 Pin UART RXD 1 _______________________________________________________________________________________________________________ Seite 12 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe USB_VBUS Input PIN Signal 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 GPIO13_GSBI4_1 GPIO16_GSBI5_0 USB_ID GPIO12_GSBI4_0 GND GPIO11_GSBI3_3 GPIO10_GSBI3_2 GPIO9_GSBI3_1 GPIO8_GSBI3_0 GPIO6_ UIM2_CLK GND GPIO2_ UIM1_CLK GPIO5_ UIM2_RST GPIO7_ UIM2_DATA GPIO4_ UIM2_DET GND HSIC_DATA GND HSIC_STROBE GND GPIO3_ UIM1_DATA GPIO1_ UIM1_RST GPIO78 GPIO79_ HSIC_RDY GPIO85 GPIO86_ GPS_EXT_LNA_EN GND VREG_USB3_3V075 GND VREG_MSME_1V8 GND VREG_UIM2 VREG_SDC1_2V95 GND VREG_UIM1 GND GND VMAIN VMAIN VMAIN VMAIN Direction related to LTE-NAD Input Output Input Output Input Power Output Input IN/OUT IN/OUT IN/OUT Input Power Output IN/OUT IN/OUT IN/OUT Input Power IN/OUT Input Power IN/OUT Input Power Output Output IN/OUT Output Output Comment 4 Pin UART Clear To Send 1 IC - Clock 4 Pin UART Ready For Receive 1 Main ground connection High Speed USB Device for communication 2 Pin UART TXD 2 2 Pin UART RXD 2 Main ground connection SIM Card - Clock Main ground connection, Corner pad Connection to Ethernet Controller Main ground connection Connection to Ethernet Controller Main ground connection SIM Card Data 1 SIM Card Reset 1 Reset of Ethernet Controller Time synchronization IN/OUT Input Power Output Power Input Power Output Power Input Power Output Power Output Power Input Power Output Power Input Power Input Power Input Power Input Power Input Power Input Power Main ground connection Output Power to USB Main ground connection Output Power Main ground connection Output Power to SIM Card 2 Output Power to SD Card 1 Main ground connection Output Power to SIM Card 1 Main ground connection Main ground connection Main power Main power Main power Main power _______________________________________________________________________________________________________________ Seite 13 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 152 153 154 160 161 162 164 165 166 167 172 PIN Signal GND GND PON HW-REV-RESISTOR PM_GPIO3 GND PM_MPP5 PM_MPP1 GND GPIO69 GPIO0_ UIM1_DET GPIO77 GPIO65 GPIO61 PON_N GND GPIO68 GPIO51 GPIO54 GND PM_MPP2 PM_GPIO2 PM_GPIO1 PM_GPIO6 GND GPIO73 GND GPIO48 GPIO49 GPIO53 Direction related to LTE-NAD Input Power Input Power Input Output IN/OUT Input Power Input Input Input Power Output Input Output Output Input Input Input Power Output Input Input Input Power Input IN/OUT IN/OUT IN/OUT Input Power IN/OUT Input Power Input Input Input Comment Main ground connection Main ground connection Power On Main ground connection PM ADC channel PM ADC channel Main ground connection Switch between main and back up antenna SIM Card Detection 1 Reset signal of SDC2 NAD Wake up NAD Update Power On Main ground connection PS-3V8-Hold BOOT_CONFIG3 BOOT_CONFIG0 Main ground connection PM ADC - channel Main ground connection Main ground connection, Corner pad BOOT_CONFIG6 BOOT_CONFIG5 BOOT_CONFIG1 GND Input Power Main ground connection LGA_PRX_ANT Connection to the antenna switch GND Input Power Main ground connection LGA_GPS_DRX_ANT Connection to the antenna connector GND Input Power Main ground connection LGA_DRX_ANT_IN LGA_DRX_ANT_OUT Input Connection to the antenna switch GND Input Power Main ground connection _______________________________________________________________________________________________________________ Seite 14 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Note: Pins should be grounded when not used in design. 3.4 Supply Voltage The external supply voltage is applied to LTE-NAD by 8 Pins on modules signal connectors. PINs 109, 110, 111, 112 for VMAIN PINs 107, 108, 113, 114 for the corresponding GND Please note that there are further main ground connection that should be connected to ensure proper NAD function. TA = -40C +85C Absolute minimum/maximum supply voltages Nominal supply voltage Recommended supply voltage Voltage drop @ GSM power burst (33dBm) During Hi RF Power GSM bursts the power amplifier can draw peak currents > 2Amps at VMAIN. The voltage drop during the GSM burst shall not exceed 100mV. 3.6V ~ 4.0V 3.8V 3.8V
<100mV 3.5 Power Consumption TA = +25C, VPH_PWR =3.8V Voice call WCDMA BC1 Voice call WCDMA BC2 Voice call WCDMA BC5 Voice call WCDMA BC8 Voice call GSM850 Voice call GSM900 Voice call GSM1800 Voice call GSM1900 Standby current GSM Standby current WCDMA Standby current LTE DRX = 5 DRX = 7 DRX = 7 Output Power Output Power max. (typ. 23dBm)
~530mA
~570mA
~630mA
~580mA 0 dBm
~145mA
~145mA
~140mA
~140mA PCL 5 (typ. 32.5 dBm) PCL 19 (typ. 5dBm)
~260mA
~270mA
~65mA
~65mA PCL 0 (typ.30.5dBm) PCL 15 (typ.0dBm)
~165mA
~165mA Tbd mA Tbd mA
~65mA
~65mA _______________________________________________________________________________________________________________ Seite 15 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe LTE data call B3 LTE data call B7 LTE data call B20 3.6 Transmitter Tbd. 3.7 Receiver Tbd. Output Power Output Power 3.8 Environmental Specification 3.8.1 Temperature Range Range Operating temp. range Operating temp. range
-20C +65C
-40C +85C Note 1 3GPP spec. conform Operational Performance might slightly deviate from 3GPP spec.
-40C +85C Storage temp. range Note 1: Due to temperature specification of the chipset, the temperature of the power manager and the temperature of the modem chip shall not exceed +85C. _______________________________________________________________________________________________________________ Seite 16 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4 Evaluation Kit 4.1 Overview For the NAD V1140-xxx, there is an evaluation board available. Features:
- On board 12V DC power supply (alternatively 3,8V DC direct connected, unbuffered).
- USB port type B
- SIM card tray
- 20 pin JTAG header for debugging
- 2 UART ports connected to DB9
- CODEC supported by I2S and I2C interfaces Using the evaluation board with an external power supply By default the module can be supplied by a switching regulator at 12V DC input voltage or by the module VCC at 3.8V. 3.8V supply should be able to deliver 3.5A max. Sense contacts are for supplies which support the corresponding feature. Using the evaluation board with on board 3.8V regulator For use at 3.8V simply disconnect the 12V supply and plug on 3.8V. Note: Make sure that the external power supply is not generating spikes or hazards higher than 4.0V. LTE-NAD Module gets damaged when spikes or hazards above 4.0V are applied RF Connector
- For RF measurements use main antenna connector _______________________________________________________________________________________________________________ Seite 17 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 2 Evaluation Kit for V1140-xxx. _______________________________________________________________________________________________________________ Seite 18 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 3 Power supply for Evaluation Kit for V1140-xxx. Figure 4 SIM card and USB interfaces for Evaluation Kit for V1140-xxx. _______________________________________________________________________________________________________________ Seite 19 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 5 RF interfaces for Evaluation Kit for V1140-xxx. Figure 6 Loudspeaker and microphone interfaces for Evaluation Kit for V1140-101. _______________________________________________________________________________________________________________ Seite 20 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4.2 Firmware Update For Firmware (FW) update the Windows software tool swupd.exe is available. To run a FW update following preconditions should be fulfilled:
- Evaluation board is power-on and connected to laptop or PC
- Qualcomm HS-USB Diagnostics 9025 Driver, version 2.0.9.1d or higher, is installed
- Virtual COM port of Qualcomm HS-USB Diagnostics 9025 is identified Note: Please ensure to have a backup of your module configuration file 4.2.1 Identify Qualcomm Diagnostics Port Number Please use the Windows Device Manager to identify virtual COM port number Figure 7 Identify Virtual COM port number of Qualcomm HS-USB Diagnostics 9025 using Windows Device Manager in provided example COM5 4.2.2 Install and Run FW Executable There is no dedicated software installation required. Please copy all files received with FW update to folder of your choice and ensure that all components are available Figure 8 Components of FW update tool Important: Before starting FW update ensure to have backup QCN file of your evaluation board. _______________________________________________________________________________________________________________ Seite 21 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe To start update process please run the batch file swupd_start.bat and enter Virtual COM port number identified in previous step. Figure 9 Complete FW update A complete FW update will take about 2:30 minutes. Please note that there are other options to run FW update. To learn more please run swupd.exe /h. 4.2.3 Known Issues Sometimes a timeout occurs. Please simply re-run the batch file in that case. Please inform us if you experience problems updating the FW on Evaluation Board. Please check if access to Qualcomm HS-USB Diagnostics port is blocked by other program. _______________________________________________________________________________________________________________ Seite 22 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 4.3 Windows 7 Driver Installation Driver installation 4.3.1 The released 64-bit Windows 7 USB host driver package is Qualcomms HK11-NA430-7_1.00.22 or higher revision, where 7_1.00.22 is the revision number. Driver can be obtained from Qualcomm. Following the license conditions, peiker is not allowed to distribute this driver. Note: There could be certificates to be installed. 4.3.2 The interfaces provided in Fig. 9 in Windows Device Manager will appear once Available interfaces
-
-
-
the USB driver is installed properly, the USB cable connects EvalBoard and computer, and the Evaluation Board is powered-up. Figure 10 Interfaces provided by Evaluation Board for OS Windows 7 In following chapters provide some information on how these interfaces could be used. AT Command interface and PPP Dial-up Modem connection 4.3.3 AT commands are used to control to some extent the modem. To send AT commands to the Modem such tools as PuTTY or similar are used. To setup PuTTY the virtual COM port can be read from Modem property information right click in Device Manager the Modem string and select Properties. The assigned virtual COM port is shown in Modem dialog box, see in Figure 11 Port COM7. _______________________________________________________________________________________________________________ Seite 23 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Figure 11 Modem Property dialog box Figure 12 Virtual COM port and modem settings Furthermore, it is recommended to add the APN string in Modem property box as shown in Figure 12. Alternatively, the APN string can be set by AT command AT+CGDCONT=1,"IP","web.vodafone.de"
(Note: The latter is the special APN valid for Vodafone Germany only). Please check with your Provider the correct APN string. Figure 13 Enter the APN delivered by your MNO in Modem Property dialog _______________________________________________________________________________________________________________ Seite 24 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Select in Network and Sharing Center of Control Panel the option Set Up a Connection or Network and enter here the Connect to the Internet option. Follow the instructions to setup a new dial-
up connection. Once the connection is setup, the Dial-up Connection is available under Network Connections. Using the Windows context menu, the connection maybe activated or deactivated. Figure 14 Dial-up Connection is available under Network Connections. Note: Prior to use this connection, a valid APN for your Mobile Network Operator must be entered, see explanation above. LTE-NAD AT command set is provided in chapter 5 AT Command interface 4.3.4 RmNet NDIS connection as Network Interface Card Figure 15 The USB driver provides a NIC (Network Interface Card). Currently according to Qualcomm proprietary information on x86, x64/AMD64, and ARM (Win8 only, for WoA/WoS) architectures following NDIS versions are supported (Source: Qualcomm Solution 00007808):
NDIS 5.1: Windows XP, Server 2003, CE NDIS 5.2: Windows Server 2003 SP2 NDIS 6.0: Windows Vista NDIS 6.1: Windows Vista SP1, Server 2008 NDIS 6.20: Windows 7, Server 2008 R2 Note: If NIC connection is not available please check with your Service Engineer if NV# 3534 is properly set. _______________________________________________________________________________________________________________ Seite 25 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Note: Especially for LTE the NIC interface provides much more data throughput as the PPP Dial-up Modem connection. Diagnostics interface 4.3.5 The Diagnostics Interface can be used with special Qualcomm Tools that are matter of dedicated license agreement with Qualcomm. Therefore, there is no additional information provided in this document. Note: Diagnostics Port is used for Firmware Updates as explained in chapter Firmware Update NMEA GNSS interface 4.3.6 The virtual NMEA COM port provides NMEA information, delivered by build-in GNSS receiver of LTE-
NAD Module. LTE-NAD provides GPS and GLONASS location information. Please contact peiker for GALILEO support. 5 AT Command Set The modules supports standard AT command as listed below. Commands are compliant to 3GPP TS 27.007 and TS 27.005 Command Description Comment AT+CMGF AT+CSCA AT+CMGS AT+CGMI AT+CGMM AT+CGMR AT+CGSN AT+CIMI AT+CMOD AT+CHUP ATD ATA ATH AT+CBST AT+CEER AT+CVHU AT+CREG AT+COPS AT+CLCK AT+CPWD AT+CLIP AT+CLIR Message Format Service Centre Address Send Message Manufacturer Identification Request model identification Request revision identification Request product serial number Request international mobile subscriber identification Call mode Hang up call Initiate a CS or PS call or supplementary service Answer incoming CS call command Hangup CS call command Select bearer service type Extended error report Voice hangup control Network registration PLMN selection Facility lock Change password Calling line identification presentation Calling line identification restriction Only one Parameter is supported by the device. _______________________________________________________________________________________________________________ Seite 26 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Command Description Comment AT+CCWA AT+CHLD AT+CUSD AT+CLCC AT+CPOL AT+CPAS AT+CFUN AT+CPIN AT+CSQ AT+CMER AT+CSIM AT+CRSM AT+CMEE AT+CGDCONT AT+CGEQREQ AT-CGATT AT+CGACT AT+CGPADDR AT+CGSMS ATE AT+CSMS AT+CSMP AT+CSDH AT+CSCB AT+CSAS AT+CRES AT+CMGL AT+CNMA AT+CMGC AT+CMMS AT+ATV AT+ATX AT+CNMI AT+CPMS AT+CMGW AT+CMSS AT+CMGD AT+CNUM AT+CPBS AT+CPBR AT+CPBW Call waiting Call related supplementary services Unstructured supplementary service data List current calls Preferred PLMN list Phone active status Set phone functionality Enter PIN Signal quality Mobile termination event reporting Generic SIM access Restricted SIM access Report mobile termination error Define PDP context Request 3G quality of service profile PS attach or detach PDP context activate or deactivate Show PDP address Select service for MO SMS messages Character Echo ON/OFF Check Message Service support Set Text Mode Parameters Show Text Mode Parameters Select Cell Broadcast Message Types Save Settings Restore Settings List messages New message acknowledgement Send Command More Messages to Send DCE response format Result code selection and call progress monitoring control New Message Indications to TE Preferred Message Storage Write Message to Memory Send Message from Storage Delete Messages Get MSISDN Select phonebook memory storage Read phonebook entries Writephonebook entry Only one Parameter is supported by the device. Only one Parameter is supported by the device. _______________________________________________________________________________________________________________ Seite 27 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Safety Recommendations according to EN60950-1 6 This device must be supplied by a limited power source according to EN 60950-1. The clearance and creepage distances required by the end product must be withheld when the module is installed. The cooling of the end product shall not negatively be influenced by the installation of the module. _______________________________________________________________________________________________________________ Seite 28 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 7 List of Acronyms 3 rd Generation Partnership Project Analog Digital Converter Abbreviated Dialing Number Assisted GPS Adaptive Multi Rate Attention Command Advanced Wireless Services Bit Error Rate Calling Line Identification Presentation Calling Line Identification Restriction Circuit Switch Data Downlink Advanced Receiver Performance Dual Tone Multi Frequency Fixed Dialing Number File Transfer Protocol Global System for Mobile communication General Purpose Input Output General Packet Radio Service Global Positioning System High Speed Uplink Packet Access Hardware Led Emitting Diode Mobile Originated Mobile Terminated Original Equipment Manufacturer Printed Circuit Board Pulse Code Modulation Protocol Data Unit Personal Identification Number Radio Frequency Restriction of Hazardous Substances Universal Asynchronous Receiver and Transmitter Universal Serial Bus Universal Subscriber Identity Module Universal Mobile Telecommunications System 3GPP ADC ADN A-GPS AMR AT AWS BER CLIP CLIR CSD DARP DTMF FDN FTP GSM GPIO GPRS GPS HSPA HW LED MO MT OEM PCB PCM PDU PIN RF RoHs UART USB USIM UMTS WCDMA Wideband Code Division Multiple Access _______________________________________________________________________________________________________________ Seite 29 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 8 Regulatory Certifications In the context of sections 8.1 and 8.1.1, the terms equipment and device refer equally to either V1140-100, V1140-101, V1140-103 or V1140-105. In the context of section 8.2, the terms apparatus, device and appareil refer equally to either V1140-101, V1140-103 or V1140-105. 8.1 USA (FCC) This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) The device may not cause harmful interference, and
(2) The device must accept any interference received, including interference that may cause undesired operation. 8.1.1 FCC Warnings and Notices WARNING: The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by peiker acustic GmbH & Co. KG could void the user's authority to operate this equipment. NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
-
- Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. _______________________________________________________________________________________________________________ Seite 30 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe 8.2 Canada (IC) This Class b digital apparatus comply with Canadian ICES-003. Cet appareil numrique de la classe b est conforme la norme NMB-003 du Canada. This device complies to Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. 8.3 OEM Responsibilities Antenna
- The antenna gain, including cable loss and based on the capabilities of the modules transmitter mounted on the PCBs specified in the related FCC filings, must not exceed 1,47dBd at 700 MHz & 850 MHz, 6dBi at 1700 MHz , 3.01dBi at 1900 MHz and 9,21 dBi at 2600 MHz for satisfying FCC RF exposure compliance.
- The antenna gain, including cable loss and based on the capabilities of the modules transmitter in a stand-alone configuration, must not exceed 0,77dBd at 700 MHz & 850 MHz, 5dBi at 1700 MHz, 2.01dBi at 1900 MHz and 8,01 dBi at 2600 MHz for satisfying FCC RF exposure compliance.
- The systems antenna(s) must be installed such that 20 cm is maintained between the antenna(s) and the body of the user or nearby persons.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The preceding statement must be included as a Caution statement in OEM product manuals in order to alert users of FCC RF Exposure compliance. _______________________________________________________________________________________________________________ Seite 31 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe Power Regulation
- The host equipment must provide power regulation circuitry to ensure that the module is supplied with stable 3.8VDC. FCC Labeling
- The V1140-100 module is labeled with its own FCC ID Number. If the FCC ID is not visible when the V1140-100 module is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-V1140-100" or "Contains FCC ID: QWY-V1140-100"
- The V1140-101 module is labeled with its own FCC ID Number. If the FCC ID is not visible when the V1140-101 module is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-V1140-101" or "Contains FCC ID: QWY-V1140-101"
- The V1140-103 module is labeled with its own FCC ID Number. If the FCC ID is not visible when the V1140-103 module is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-V1140-103" or "Contains FCC ID: QWY-V1140-103"
- The V1140-105 module is labeled with its own FCC ID Number. If the FCC ID is not visible when the V1140-105 module is installed inside another device, then the host device must contain the FCC ID number with the statement such as the following: "Contains Transmitter Module FCC ID: QWY-V1140-105" or "Contains FCC ID: QWY-V1140-105"
IC Labeling
- The V1140-101 module is labeled with its own IC ID Number. If the IC ID is not visible when the V1140-101 module is installed inside another device, then the host device must contain the IC ID number with the statement such as the following: "Contains Transmitter Module IC: 6588A-V1140101" or "Contains IC:
6588A-V1140101".
- The V1140-103 module is labeled with its own IC ID Number. If the IC ID is not visible when the V1140-103 module is installed inside another device, then the host device must contain the IC ID number with the statement such as the following: "Contains Transmitter Module IC: 6588A-V1140103" or "Contains IC:
6588A-V1140103".
- The V1140-105 module is labeled with its own IC ID Number. If the IC ID is not visible when the V1140-105 module is installed inside another device, then the host device must contain the IC ID number with the statement such as the _______________________________________________________________________________________________________________ Seite 32 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe following: "Contains Transmitter Module IC: 6588A-V1140105" or "Contains IC:
6588A-V1140105". _______________________________________________________________________________________________________________ Seite 33 phG: peiker Verwaltungs GmbH, Vorsitzender der Geschftsfhrung: Andreas Peiker, Geschftsfhrer: Stephan Graf von der Schulenburg, Amtsgericht Bad Homburg 1369 peiker acustic GmbH & Co. KG, Max-Planck-Strae 32, D-61381 Friedrichsdorf, Amtsgericht Bad Homburg HRA 1897 Vorsitzender des Aufsichtsrates: Prof. Dr. Agilolf Lamperstorfer Ein Unternehmen der peiker Firmengruppe
This product uses the FCC Data API but is not endorsed or certified by the FCC