QCWB342 Dual Band 2x2 MIMO 802.11ac/abgn WLAN plus BT User Manual

 

WB342 Modular Certification OEM Integrator Instructions MKG-17218 Ver. 1.4 July 17, 2013 Confidential and Proprietary - Qualcomm Atheros, Inc. Not to be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of Qualcomm Atheros, Inc. QUALCOMM is registered trademark of Qualcomm Incorporated. ATHEROS is a registered trademark of Qualcomm Atheros, Inc. Any other registered and unregistered trademarks are the property of Qualcomm Incorporated, Qualcomm Atheros, Inc. or their respective owners and used with permission. Registered marks owned by Qualcomm Incorporated and Qualcomm Atheros, Inc. are registered in the United States of America and may be registered in other countries. This technical data may be subject to U.S. and international export, re-export, or transfer (export) laws. Diversion contrary to U.S. and international law is strictly prohibited. Qualcomm Atheros, Inc. 1700 Technology Drive San Jose, CA 95110-1383 U.S.A. Copyright 2011 Qualcomm Atheros, Inc. All rights reserved. Date May 2013 Description Initial release June 2013 July 2013 July 2013 Revision content to Section 8 Revision for some sentence Change antenna separation distance to 5 cm Revision history Revision Ver. 1.1 Ver. 1.2 Ver. 1.3 Ver. 1.4 NOTE: The Qualcomm Atheros (QCA) design radio module (the Module) is designed for use only in specific countries in which QCA has obtained certificates of compliance with local laws and regulations. Therefore, the Module may not be sold, operated or incorporated into products for use in countries for which it has not been certified. See Section 3 herein. In addition, any deviation from the settings, methods, conditions and restrictions for integration of the Module into a host system, as detailed in this document, could be a violation of applicable national law and may be punishable as such, and in such event, the products into which the Module is incorporated may not be lawfully distributed or sold in such countries. QCA assumes no responsibility for any liability or loss related to installation, integration or operation of the Module. MKG-17218 Ver. 1.4 2 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions Contents 1 Introduction ...................................................................................................... 4 2 Applicable Module ........................................................................................... 4 3 Available Global Modular Approvals from Qualcomm Atheros .................. 5 4 Additional Regulatory Conformance Testing and/or Submissions Required by the Integrator ........................................................................... 5 5 Compliant/Allowable Tx Power Settings Programmed into EEPROM ........ 7 6 Allowable Antennas For Use With The Radio Module .................................. 7 7 Antenna Placement inside the Host System and RF Safety ........................ 8 8 Simultaneous Transmission with Other Integrated or Plug-In Radios ....... 8 9 Module May Not Be Installed by End Users .................................................. 9 10 Required Labeling on the Outside of the Host .......................................... 10 10.1 FCC ........................................................................................................................... 10 10.2 Taiwan NCC ............................................................................................................. 10 10.3 European Community R&TTE ................................................................................. 11 11 Required Labeling on the Module .............................................................. 12 11.1 FCC labeling on the Module ..................................................................................... 12 11.2 Rest of world labeling on the Module ....................................................................... 12 11.3 Instructions to download the sample global label artwork with certification IDs .... 12 12 Required Regulatory Wording for User Manual/Installation Manual ....... 13 12.1 FCC compliance information .................................................................................... 13 12.2 Industry Canada notice ............................................................................................. 14 12.3 European Community (R&TTE) user manual wording and declaration .................. 15 12.4 European Community (R&TTE) Declaration of Conformity for System................. 17 12.5 Taiwan user manual wording .................................................................................... 17 12.6 Korea user manual wording ...................................................................................... 18 13 OEM Integrator Checklist ............................................................................ 19 MKG-17218 Ver. 1.4 3 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 1 Introduction This document describes the steps that the OEM integrator must follow when designing and manufacturing a system utilizing a Qualcomm Atheros (QCA) design radio module (the Module). Failure to follow the instructions in this document may invalidate the FCC certification and authorization of the Module for use in the U.S. and in other countries. The Qualcomm Atheros modular certifications described in this document apply only to radio conformance for the Module. The OEM integrator is responsible for all system-level EMI/EMC and Product Safety testing and certification that apply to the host system in the U.S. and other countries where the system will be marketed or sold. 2 Applicable Module Part Number: WB342 (Regulatory model: QCWB342) FCC ID: PPD-QCWB342 IC: 4104A-QCWB342 MKG-17218 Ver. 1.4 4 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 3 Available Global Modular Approvals from Qualcomm Atheros Module certification is limited to those countries for which Qualcomm Atheros has obtained radio modular approvals. Integrators can access the current list of certified countries in one of two ways:

1. Log on to the Qualcomm Atheros secure customer support site. Follow the links to regulatory certifications. Search for the folder WB342 on the support site. Or, if you do not have access to the customer support site, then:

2. Contact your Qualcomm Atheros account representative to request access to the country list and modular certificates. OEM integrators must receive their own radio certification for any country in which the system will be sold if a modular certification for that country is not available from Qualcomm Atheros. 4 Additional Regulatory Conformance Testing and/or Submissions Required by the Integrator The global modular certifications apply to radio conformance for the Module only. The OEM integrator is responsible for additional system-level EMI/EMC and Product Safety testing and certification that applies in the U.S. and other countries to the host system containing the Module. This includes, but is not limited to, Federal Communications Commission (FCC) Part 15 Class B Digital Emissions, China CCC, Taiwan BSMI, Korea KC, ETSI EN 301 489-17 and others. These system-level EMC tests are to be done with the Module installed and included in the scope of the submission. Some of the countries for which modular certifications are provided require additional submissions, authorizations or import permission by the system-vendor or importer. The integrator is responsible for these additional actions. By way of example, the OEM integrator must take additional action for radio certification in these countries:

Malaysia Each importer/distributor needs to file for import permission Singapore Recommend use of importers own local radio dealer number Israel Additional approval certificate required for importer Modular radio certification is not possible in some countries. For such countries, OEM integrators must ensure radio certification for the end system is obtained, before placing the product on the market. A current list of applicable countries can be provided by Qualcomm Atheros. MKG-17218 Ver. 1.4 5 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions Please contact your Qualcomm Atheros account representative if you have questions about the additional regulatory conformance testing and/or related submissions. MKG-17218 Ver. 1.4 6 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 5 Compliant/Allowable Tx Power Settings Programmed into EEPROM This file contains the allowable transmit power settings that are to be programmed into the Module during original manufacturing:

CTL File Name: ctl_wb342_notxbf.art NOTE: Programming in higher values than provided for in this file will invalidate all radio certifications for this module. OEM integrators can access the file one of two ways:

Log on to the Qualcomm Atheros secure customer support site, then:

a. Download the Atheros Radio Test (ART) package b. Browse to this folder in the zip package: command\WB342 c. Find CTL File (file name reference above) OR, if you do not have access to the customer support site, then:

Contact your Qualcomm Atheros account representative to request the CTL file. 6 Allowable Antennas to Use with the Radio Module The module is certified for use only with certain antennas as described in this section. NOTE: Allowed Antenna Type: PIFA with omnidirectional pattern formed from stamped metal or film. Table 1 Allowed Maximum Gain (dBi), Including Antenna Cable Loss 2.4 GHz 5.150-5.350 GHz 5.470-5.850 GHz 3.60 3.08 4.76 WARNING: Use of other antenna types or the same type of antenna but with higher gain than listed above is not allowed without additional testing and appropriate FCC approval. Contact your Qualcomm Atheros account representative for additional guidance if you decide to use different antenna types or higher gain antennas in the end system. Some examples of antenna types not considered the same type as PIFA are dipole/monopole, PCB trace, patch, and chip antennas. In addition, regulatory agencies in Japan, Korea, and Taiwan require submission of antenna specification sheets for all antenna models used with the QCA module. This notification process must be followed by the integrator before original product launch and whenever new host systems

(with new antenna models) are launched. Notification of All Antenna Models to be used with the Module:

For training on the notification process contact:

Stanley Lin, Regulatory Program Manager [mailto:slin@qualcomm.com]

For submitting antenna specifications: mailto:atheros-ant@dspr.co.jp MKG-17218 Ver. 1.4 7 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 7 Antenna Placement inside the Host System and RF Safety The FCC and other countries regulatory bodies impose strict conditions and limitations on the RF exposure levels of end products. Acceptable RF exposure levels for this Module depend on transmit power, the location of the transmitting antenna(s) inside the host system and the expected separation of the transmitting antennas to the end user. OEM integrators must take great care to ensure each host system complies with the applicable RF exposure requirements. NOTE: The antenna-to-user separation distance must be greater than 9.5 mm. WARNING: Failure to adhere to these separation/spacing rules will invalidate the FCC certification for the Module. This separation is measured between the closest point of each transmitting antenna inside the host device to the point of contact by the user or nearby person outside of the host device. For notebooks/netbooks/laptops, the LCD is opened 90 degrees/perpendicular to the keyboard. The separation distance is then measured from the nearest point of each transmitting antenna to the bottom of the host. For notebooks/netbooks/laptops, the transmitting antenna cables shall be positioned away from antenna elements to conform to the configuration tested for compliance. When transmitting antennas are installed in the display section of notebook/netbook/laptops, the display section shall not have metallic components and material that can influence or change the operating and RF exposure characteristics of the antennas. The separation between the main and aux antennas must be at least 5 cm. (applied when module support MIMO) The transmitter module may not be co-located with any other transmitter or antenna. Where one or more of the conditions above cannot be met for a particular host system, additional testing will be required to secure the necessary certifications for the system. You may contact your Qualcomm Atheros account representative with any questions regarding compliance of the host system(s) with these restrictions. NOTE: These restrictions do not apply to a receive-only antenna. 8 Simultaneous Transmission with Other Integrated or Plug-

In Radios The FCC imposes conditions and limitations when additional radio(s) are co-located in the same host system as the Qualcomm Atheros Module with capability to transmit simultaneously. The detailed rules from the FCC are described in various Knowledge Database publications that may be found using the instructions below. Co-locating other radios such as an integrated or plug in Wireless WAN/cellular radio with the Qualcomm Atheros Wireless LAN module requires additional evaluation and possibly submission for authorization from the FCC. MKG-17218 Ver. 1.4 8 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions Because the rules are highly dependent on the characteristics of the particular radios that are co-

located and simultaneously transmitting, the OEM integrator should seek guidance from a knowledgeable test lab or consultant to determine if additional testing and FCC certification is required. In this case, failure to evaluate and follow the required FCC procedures will invalidate the FCC certification of the Module and end system. To download the FCC rules for collocated radios:

1. https://apps.fcc.gov/oetcf/kdb/index.cfm 2. Enter 616217 in the publication number search box 3. Download latest applicable version of KDB 616217 document. For expert advice regarding collocation rules, we recommend you contact an FCC-approved Telecommunication Certification Body (TCB)::

1. https://apps.fcc.gov/oetcf/kdb/index.cfm. 2. Choose your country and or state from the pull-down list. 3. Scroll through the search results and choose a TCB contact from which to seek advice. You may also contact your Qualcomm Atheros account representative with any questions regarding compliance of the host system(s) with the above restrictions. 9 Module May Not Be Installed by End Users FCC rules require this Module to be installed in host systems at the factory by the OEM integrator. Thus, end users of the system may not install the Module. Therefore, the host product user instructions must not advise the end user on how to access or remove the Module. Additional FCC authorization/filing is needed to allow end user installation of radio modules. MKG-17218 Ver. 1.4 9 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 10 Required Labeling on the Outside of the Host NOTE: Explanatory text in red font must not be included in the final label. 10.1 FCC The FCC requires a label on the outside of the host system visible to the end user. Example wording is:

Contains:

FCC ID: XXX-XXXXXXX IC: XXXXX-XXXXXX

(Replace Xs with actual IDs found in section 2). The FCC requires a logo signifying emissions compliance on the outside of the host system. Additional options are available for placement of the FCC label on the host. Please refer to the FCC Knowledge Database KDB784748 found at https://apps.fcc.gov/oetcf/kdb/index.cfm. NOTE: The Integrator is responsible to perform FCC Part 15 Class B digital emissions testing on the end system with the radio Module installed. The FCC logo below should not be affixed unless the OEM integrator has obtained the necessary Part 15 approval, e.g., self-declaration of conformity. If the host system is approved to FCC Class B digital emissions limits under a grant of certification issued by a TCB, the FCC ID number shown on the grant should be used on the label instead of the FCC logo below. 10.2 Taiwan NCC Taiwan NCC requires a label on the outside of the host system visible to the end user. The required wording is:

XXXXXXXXXX

(Replace Xs with actual IDs found in section 2 ). MKG-17218 Ver. 1.4 10 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 10.3 European Community R&TTE The European Community R&TTE Directive requires the CE Marking shown below on the outside of the host AND on the outside of the shipping container/packaging:

The European Community R&TTE Directive also requires the following note to consumers on the outside of the shipping container/packaging:

Important Notice: This product is a Radio LAN device operating in 2.4 & 5 GHz bands for Home and Office use in the E.E.A. States with restrictive use are highlighted in grey. Refer to user documentation for details. AT CZ FI EE IS LV PL SK BE DE FR HU LI MT PT CH DK GB IT LT NL SE CY ES GR IE LU NO SI NOTE: The Integrator is expected to translate the text in this Section into the appropriate local languages for the European countries in which the product will be marketed or sold. MKG-17218 Ver. 1.4 11 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 11 Required Labeling on the Module 11.1 FCC labeling on the Module The Integrator must ensure that the FCC ID (as indicated in section 2) is affixed on the Module along with other country certification numbers and logos as described herein. NOTE: The Module ODM may affix regulatory labeling at time of Module manufacturing. However, the PCOEM must ensure the Module label is complete, correct and applicable for all countries to which the host system is to be imported, marketed, or sold. 11.2 Rest of world labeling on the Module The Integrator must ensure the Module includes a global regulatory label with certification numbers and logos for all target countries. The system integrator is responsible to confirm the final regulatory label on the radio Module contains all required certification IDs for all countries in which the system will be marketed or sold. It is recommended that the PCOEM implement a review and sign-off process as well as change control process with each Module ODM to ensure that the module label meets the PCOEMs requirements. Qualcomm Atheros provides sample artwork with the applicable certification numbers for this Module. The provided .PDF document can be opened using Adobe Illustrator so the sample artwork can be copied and modified as needed. Therefore the final label produced by the Module manufacturer will vary from this sample. However, the logos and certification numbers must be those shown in the sample global label. Contact your Qualcomm Atheros account representative with any questions regarding module labeling. 11.3 Instructions to download the sample global label artwork with certification IDs 1. Log on to the Qualcomm Atheros secure customer support site. Follow the links to regulatory certifications. NOTE: Search for the folder WB342 in the support site. 2. Find the folder: Sample Labeling for Module. 3. Download the PDF file found in the folder. OR, if you dont have access to the customer support site, then:

Contact your Qualcomm Atheros account representative to request the Sample Label file. MKG-17218 Ver. 1.4 12 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 12 Required Regulatory Wording for User Manual/Installation Manual The integrator must include text in the user manual meeting the regulators requirements. The text below or similar wording should be used. NOTE: Text in red font must be replaced. 12.1 FCC compliance information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product does not contain any user serviceable components. Any unauthorized product changes or modifications will invalidate warranty and all applicable regulatory certifications and approvals, including authority to operate this device. FCC Part 15 Digital Emissions Compliance We [System Manufacturer Name, Address, Telephone], declare under our sole responsibility that the product [System Name] complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from the one the receiver is connected to. Consult the dealer or an experienced radio/TV technician for help. The user may find the following booklet prepared by the Federal Communications Commission helpful:

The Interference Handbook This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Stock No.004-000-00345-4. MKG-17218 Ver. 1.4 13 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions

(Notice for 5GHz) Operations in the 5.15-5.25GHz band are restricted to indoor usage only. (For 5GHz only)

(RF exposure statement) Radiation Exposure Statement:

The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. 12.2 Industry Canada notice This device complies with Canadian RSS-210. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable.

(Notice for 5GHz) Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

(iv) Users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

MKG-17218 Ver. 1.4 14 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer la limite de p.i.r.e.;

(iii) le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas.

(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

(RF exposure statement) Radiation Exposure Statement:

The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. 12.3 European Community (R&TTE) user manual wording and declaration NOTE: Text in red font must be replaced with name of company responsible for placing the system on the European Community Market. Europe EU Declaration of Conformity MKG-17218 Ver. 1.4 15 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards:

EN300 328, EN 301 893, EN 301 489-17, EN60950, EN 62311 esky [Czech]

[COMPANY NAME] tmto prohlauje, e tento Radiolan je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Dansk [Danish]

Undertegnede [COMPANY NAME] erkl rer herved, at f lgende udstyr Radiolan overholder de v sentlige krav og vrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklrt [COMPANY NAME] dass sich das Gert Radiolan in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian]

Kesolevaga kinnitab [COMPANY NAME] seadme Radiolan vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. English Hereby, [COMPANY NAME], declares that this Radiolan is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol [Spanish] Por medio de la presente [COMPANY NAME] declara que el Radiolan cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

[Greek] [COMPANY NAME] Radiolan 1999/5/. Franais [French] Par la prsente [COMPANY NAME] dclare que l'appareil Radiolan est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. slenska [Icelandic]

Hr me lsir [COMPANY NAME] yfir v a Radiolan er samr mi vi grunnkrfur og arar krfur, sem gerar eru tilskipun 1999/5/EC. Italiano [Italian]

Con la presente [COMPANY NAME] dichiara che questo Radiolan conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian]

Ar o [COMPANY NAME] deklar, ka Radiolan atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi

[Lithuanian]

Malti [Maltese]

Magyar

[Hungarian]

Nederlands

[Dutch]

iuo [COMPANY NAME] deklaruoja, kad is Radiolan atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hawnhekk, [COMPANY NAME], jiddikjara li dan Radiolan jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Alulrott, [COMPANY NAME] nyilatkozom, hogy a Radiolan megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Hierbij verklaart [COMPANY NAME] dat het toestel Radiolan in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Norsk [Norwegian]

[COMPANY NAME] erkl rer herved at utstyret Radiolan er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999/5/EF. Polski [Polish]

Niniejszym [COMPANY NAME] owiadcza, e Radiolan jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus

[Portuguese]

Slovensko

[Slovenian]

[COMPANY NAME] declara que este Radiolan est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE.

[COMPANY NAME] izjavlja, da je ta Radiolan v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Slovensky [Slovak]

[COMPANY NAME] tmto vyhlasuje, e Radiolan spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. Suomi [Finnish]

[COMPANY NAME] vakuuttaa tten ett Radiolan tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. MKG-17218 Ver. 1.4 16 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions Svenska [Swedish] Hrmed intygar [COMPANY NAME] att denna Radiolan str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Table 2 Restrictions for use of 2.4 GHz frequencies in European Community countries. The restriction descriped below follows ERC/REC 70-03(Edition of September 2011). It is recommended to check latest edition for updated restrictions. France:

The outdoor use is limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz. Italia:

For private use, a general authorisation is required if WAS/RLANs are used outside own premises. For public use, a general authorisation is required. 12.4 European Community (R&TTE) Declaration of Conformity for System In addition to including the radio conformity wording described in the previous section in the user manual, the end integrator must also create and sign a European Declaration of Conformity

(DoC) for all European Directives applicable to the end product. At a minimum, this will be a DoC per the R&TTE Directive covering Radio, EMC, product Safety and RF Exposure essential requirements. The DoC must reference harmonized standards used for all radios present in the system. Full details of R&TTE DoC requirements can be found at:

http://www.ec.europa.eu/enterprise/sectors/rtte/index_en.htm NOTE: An image of the DoC signed by the OEM integrator may be included in the user manual or a link to the DoC on the integrators company web site should be provided in the user documentation. 12.5 Taiwan user manual wording

MKG-17218 Ver. 1.4 17 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 5.25-5.35 (GHz)(For 5GHz only) 12.6 Korea user manual wording Korea KCC MKG-17218 Ver. 1.4 18 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION WB342 Modular Certification OEM Integrator Instructions 13 OEM Integrator Checklist The party below will implement the Qualcomm Atheros Module in host systems in accordance with the instructions specified in this document and the documents referenced herein. The OEM integrator will ensure the Module is integrated in a host systems using only the approved antenna model(s) described in this document. The OEM integrator will ensure the antenna placement inside the host system will maintain the required spacing to end user for RF Exposure compliance, as specified in this document. If other radios are integrated inside the host with the Qualcomm Atheros Module, the OEM integrator will contact its test lab, TCB or Qualcomm Atheros to determine if additional FCC compliance evaluation is required to meet FCC collocation rules. The OEM integrator will ensure end user documentation will contain the specified regulatory wording and ensure the host system and the Module itself are labeled as specified in this document. The OEM integrator will ensure the Module is programmed in the factory with compliant transmit power not exceeding the levels specified in this document. Qualcomm Atheros requests that the OEM integrator acknowledge its receipt of this document and the above instructions. You may contact Qualcomm Atheros with any questions concerning this document or the responsibilities of the OEM integrator. Company Name ___________________________ Signature ___________________________ Company Address ___________________________ Name ___________________________ ___________________________ Title ___________________________ Email ___________________________ Phone ___________________________ Date ___________________________ NOTE: Please email a signed and completed copy of this acknowledgment to moduleinstructions@qualcomm.com. MKG-17218 Ver. 1.4 19 Confidential and Proprietary - Qualcomm Atheros, Inc. MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION