Raspberry Pi 3 Model B - Single Board Computer Users manual

Raspberry Pi Regulatory Compliance and Safety Information Product Name: Raspberry Pi 3, Model B Uncased Version IMPORTANT PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE Warnings This product shall only be connected to an external power supply rated at 5V dc, and a maximum current of 1500 2000 mA. Any external power supply used with the Raspberry-Pi shall comply with relevant regulations and standards applicable in the country of intended use. This product should not be overclocked as this may make certain components very hot. This product should be operated in a well ventilated environment and should not be covered. This product should be placed on a stable, flat, non-conductive surface in use and should not be contacted by conductive items. This product should not be used within 20cm of the body with the Wi-Fi/Bluetooth switched on. Instructions for safe use To avoid malfunction or damage to your Raspberry Pi please observe the following:

Do not expose it to water, moisture or place on a conductive surface whilst in operation. Do not expose it to heat from any source; the Raspberry Pi is designed for reliable operation at normal ambient room temperatures. Take care whilst handling to avoid mechanical or electrical damage to the printed circuit board and connectors. Avoid handling the Raspberry Pi while it is powered. Only handle by the edges to minimize the risk of electrostatic discharge damage. All peripherals used with the Raspberry Pi should comply with relevant standards for the country of use and be marked accordingly to ensure that safety and performance requirements are met. These articles include but are not limited to keyboards, monitors and mice used in conjunction with the Raspberry Pi. Compliance Information The Raspberry Pi complies with the relevant provisions of the RoHS Directive for the European Union. WEEE Directive Statement for the European Union In common with all Electronic and Electrical products the Raspberry Pi should not be disposed of in household waste. Alternative arrangements may apply in other jurisdictions. CMIIT ID: XXXXXXXXXX EMC Compliance Statements European Union (EU) Electromagnetic Compatibility Directive Compliance Statement This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to the European Standard EN 55022. Warning: This is an EN 55022 Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Federal Communications Commission (FCC) Emissions Compliance Statement This equipment has been tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

equipment is operated in a commercial environment.

(1) This device may not cause harmful interference, and

(1) This device may not cause harmful interference, and

(1) This device may not cause harmful interference, and This device complies with Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device might

(2) This device must accept any interference received, including interference that may cause undesired operation.

(2) This device must accept any interference received, including interference that may cause undesired operation.

(2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific not cause harmful interference, and (2) this device must accept any interference received, including interference that might specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any cause undesired operation. Operation is subject to the following two conjunction with any other antenna or transmitter. conjunction with any other antenna or transmitter. specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction other antenna or transmitter. Warning: Operation of this equipment in a residential area is likely to cause harmful interference, in which case the conditions:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate with any other antenna or transmitter. user will be required to correct the interference at their own expense.

(1) This device may not cause harmful interference, the equipment Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate and the equipment the equipment the equipment

(2) This device must accept any interference received, including interference that may cause undesired operation. Industry Canada Class B Emissions Compliance Statement Industry Canada Class B Emissions Compliance Statment Industry Canada Class B Emissions Compliance Statment This Class B digital apparatus complies with Canadian ICES-003. This Class B digital apparatus complies with Canadian ICES-003. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Australia and New Zealand Class B Emissions Compliance Statement Warning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. www.raspberrypi.org