| submitted | available | document details (if available) | source link |
|---|---|---|---|
| August 01 2011 | RTL8192 datasheet John Russell Acrobat Distiller 7.0 (Windows) |
| various | User Manual | Users Manual | 163.76 KiB | / August 01 2011 |
RTL8188CUS Slim Module Solo Card Users Manual Rev. 1.0 15 Oct 2010 Realtek Semiconductor Corp. No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu 300, Taiwan Tel.: +886-3-578-0211. Fax: +886-3-577-6047 www.realtek.com.tw RTL8188CUS Slim Module Solo Card User Manual COPYRIGHT 2009 Realtek Semiconductor Corp. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of Realtek Semiconductor Corp. DISCLAIMER Realtek provides this document as is, without warranty of any kind, neither expressed nor implied, including, but not limited to, the particular purpose. Realtek may make improvements and/or changes in this document or in the product described in this document at any time. This document could include technical inaccuracies or typographical errors. TRADEMARKS Realtek is a trademark of Realtek Semiconductor Corporation. Other names mentioned in this document are trademarks/registered trademarks of their respective owners. USING THIS DOCUMENT This document is intended for the software engineers reference and provides detailed programming information. Though every effort has been made to ensure that this document is current and accurate, more information may have become available subsequent to the production of this guide. In that event, please contact your Realtek representative for additional information that may help in the development process. ii Rev.1.0 RTL8188CUS Slim Module Solo Card User Manual Table of Contents 1. GENERAL DESCRIPTION................................................................................................................................................1 1.1. RTL8188CUS .................................................................................................................................................................1 2. FEATURES...........................................................................................................................................................................2 2.1. RTL8188CUS .................................................................................................................................................................2 PRODUCT SPECIFICATIONS .................................................................................................................................................4 2.3. CONNECTER PIN ASSIGNMENT.........................................................................................................................................4 2.4. MECHANICAL..................................................................................................................................................................5 2.5. ENVIRONMENTAL ............................................................................................................................................................6 2.5.1. Operating ...............................................................................................................................................................6 Storage....................................................................................................................................................................6 2.5.2. 2.6. FUNCTIONAL SPECIFICATIONS .........................................................................................................................................7 2.7. WARNING ........................................................................................................................................................................8 4.5.1 Federal Communication Commission Interference Statement ......................................................................................8 4.5.2 Industry Canada Statement ........................................................................................................................................10 4.5.3 NCC...................................................................................................................................................................11 List of Tables TABLE 1. CONNECTER PIN ASSIGNMENT .................................................................................................................................4 TABLE 2. FUNCTIONAL SPECIFICATIONS .......................................................................................................................................7 List of Figures FIGURE 1. RTL8188CUS SLIM MODULE MECHANICAL SPECIFICATION .......................................................................................5 iii Rev.1.0 RTL8188CUS Slim Module Solo Card User Manual 1. General Description 1.1. RTL8188CUS The Realtek RTL8188CUS is a highly integrated single-chip Wireless LAN (WLAN) controller compatible with the IEEE 802.11n specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip. The RTL8188CUS provides a complete solution for a high-performance wireless client. The RTL8188CUS baseband implements Multiple Input, Multiple Output (MIMO) Orthogonal Frequency Division Multiplexing (OFDM) with one transmit and one receive path (1T1R). Features include one spatial stream transmission, short Guard Interval (GI) of 400ns, spatial spreading, and support for both 20MHz and 40MHz channel bandwidth. For legacy compatibility, Direct Sequence Spread Spectrum (DSSS), Complementary Code Keying (CCK) and OFDM baseband processing are included to support all IEEE 802.11b, and 802.11g data rates. Differential phase shift keying modulation schemes, DBPSK and DQPSK with data scrambling capability are available, and CCK provides support for legacy data rates, with long or short preamble. The high speed FFT/IFFT paths, combined with BPSK, QPSK, 16QAM, and 64QAM modulation of the individual subcarriers, and rate compatible punctured convolutional coding with coding rate of 1/2, 2/3, 3/4, and 5/6, provide higher data rates of 54Mbps and 150Mbps for IEEE 802.11g and 802.11n OFDM respectively. The RTL8188CUS builds in an enhanced signal detector, an adaptive frequency domain equalizer, and a soft-decision Viterbi decoder to alleviate severe multi-path effects and mutual interference in the reception of multiple streams. Robust interference detection and suppression are provided to protect against Bluetooth, cordless phone, and microwave oven interference. Efficient IQ-imbalance, DC offset, phase noise, frequency offset, and timing offset compensations are provided for the radio frequency front-end. Selectable digital transmit and receive FIR filters are provided to meet transmit spectrum mask requirements and to reject adjacent channel interference, respectively. The RTL8188CUS supports fast receiver Automatic Gain Control (AGC) with synchronous and asynchronous control loops among antennas, antenna diversity functions, and adaptive transmit power control functions to obtain better performance in the analog portions of the transceiver. The RTL8188CUS MAC supports 802.11e for multimedia applications, 802.11i for security, and 802.11n for enhanced MAC protocol efficiency. Using packet aggregation techniques such as A-MPDU with BA and A-MSDU, protocol efficiency is significantly improved. Power saving mechanisms such as U-APSD, and APSD, reduces power wasted during idle time, and compensates for the extra power required to transmit OFDM. The RTL8188CUS provides simple legacy and 20MHz/40MHz co-existence mechanisms to ensure backward and network compatibility. 1 Rev.1.0 2. Features 2.1. RTL8188CUS General
46-pin QFN
CMOS MAC, Baseband PHY and RF in a single chip for IEEE 802.11b/g/n compatible WLAN
75Mbps receive PHY rate and 75Mbps transmit PHY rate using 20MHz bandwidth
150Mbps receive PHY rate and 150Mbps transmit PHY rate using 40MHz bandwidth
Compatible with 802.11n specification
Backward compatible with 802.11b/g devices while operating at 802.11n data rates Host Interface
USB Port Standards Supported
IEEE 802.11b/g/n compatible WLAN
IEEE 802.11e QoS Enhancement
(WMM)
IEEE 802.11i (WPA, WPA2). Open, shared key, and pair-wise key authentication services MAC Features
Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU)
Low latency immediate High-Throughput Block Acknowledgement (HT-BA) RTL8188CUS Slim Module Solo Card User Manual
Long NAV for media reservation with CF-End for NAV release
PHY-level spoofing to enhance legacy compatibility
Power saving mechanism
Channel management and co-existence
Multiple BSSID feature allows the RTL8188CUs to assume multiple MAC identities when used as a wireless bridge
Supports Wake-On-WLAN via Magic Packet and Wake-up frame
Transmit Opportunity (TXOP) Short Inter-Frame Space (SIFS) bursting for higher multimedia bandwidth Peripheral Interfaces
General Purpose Input/Output (8 pins)
Three configurable LED pins PHY Features
IEEE 802.11n OFDM
One Transmit and one Receive path
20MHz and 40MHz bandwidth
(1T1R) transmission
Short Guard Interval (400ns)
DSSS with DBPSK and DQPSK, CCK modulation with long and short preamble
OFDM with BPSK, QPSK, 16QAM, and 64QAM modulation. Convolutional Coding Rate: 1/2, 2/3, 3/4, and 5/6
Maximum data rate 54Mbps in 802.11g, and 150Mbps in 802.11n
Switch diversity for DSSS/CCK
Hardware antenna diversity 2 Rev.1.0 RTL8188CUS Slim Module Solo Card User Manual
Selectable digital transmit and receive FIR filters
Programmable scaling in transmitter and receiver to trade quantization noise against increased probability of clipping
Fast receiver Automatic Gain Control
(AGC)
On-chip ADC and DAC
28-ball 2.57 x 3.21x0.6mm 0.5mm pitch WLCSP Package , no underfill required
Design optimized for low cost PCB manufacture. 3 Rev.1.0 RTL8188CUS Slim Module Solo Card User Manual Product specifications 2.2. Connecter Pin Assignment Table 1. Connecter Pin Assignment Pin definition 3.3V NC NC NC GND USB D+
USB D-
WiFi_Power_OFF W_B_LED GND Type P G I/O I/O I/O I/O/
G Description 3.3V DC Power Supply No connection No connection No connection Ground USB D+ for WiFis USB2.0 USB D- for WiFis USB2.0 WiFi on: High; WiFi off: Low LED is active low. Ground Pin 1 2 3 4 5 6 7 8 9 10 4 Rev.1.0 2.3. Mechanical RTL8188CUS Slim Module Solo Card User Manual Figure 1. RTL8188CUs Slim Module Mechanical Specification 5 Rev.1.0 2.4. Environmental RTL8188CUS Slim Module Solo Card User Manual 2.4.1. Operating Operating Temperature:
Relative Humidity:
2.4.2. Storage Temperature:
Relevant Humidity:
0 to 70 C 5-90% (non-condensing)
-55 to 125 C 5-95% (non-condensing) 6 Rev.1.0 2.5. Functional Specifications RTL8188CUS Slim Module Solo Card User Manual Table 2. Functional Specifications WiFi:
IEEE 802.11b, IEEE 802.11g, Draft IEEE 802.11n, IEEE 802.11d, IEEE 802.11e, IEEE 802.11h, IEEE 802.11i Standards Bus Interface Form Factor Data Rate Media Access Control Modulation Techniques Network Architecture Operating Channel Frequency Range Security Operating Voltage WiFi: USB Slim Module 6mm x 80mm 802.11b:
11, 5.5, 2, 1 Mbps;
802.11g:
802.11n:
54, 48, 36, 24, 18, 12, 9, 6 Mbps MCS 0 to 7 for HT20MHz;
MCS 0 to 7 for HT40MHz WiFi:
CSMA/CA with ACK CCK, DQPSK, DBPSK 64 QAM, 16 QAM, QPSK, BPSK BPSK, QPSK, 16-QAM, 64-QAM 802.11b:
802.11g:
802.11n:
WiFi:
Ad-hoc mode (Peer-to-Peer ) Infrastructure mode WiFi 2.4GHz:
11: (Ch. 1-11) United States 13: (Ch. 1-13) Europe 13: (Ch. 1-14) Japan 2.400GHz ~ 2.4835 GHz WiFi :
WPA, WPA-PSK, WPA2, WPA2-PSK, WEP 64bit & 128bit, IEEE 802.11x, IEEE 802.11i 3.3 V 9% I/O supply voltage 7 Rev.1.0 RTL8188CUS Slim Module Solo Card User Manual 2.6. Warning 4.5.1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna, As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). 8 Rev.1.0 RTL8188CUS Slim Module Solo Card User Manual IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: TX2-RTL8188CUS. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 3.9 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 9 Rev.1.0 RTL8188CUS Slim Module Solo Card User Manual 4.5.2 Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 3.9dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna. As long as conduction above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). The antenna must be installed such that 20 cm is maintained between the antenna and users. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: Contains IC :
6317A-RTL8188CUS. Manual Information That Must be Included The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove. 10 Rev.1.0 RTL8188CUS Slim Module Solo Card User Manual This RF module in the users manual of the end product which integrates this module. The users manual for OEM Integrators must include the following information in a prominent location IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements. The antenna must not be co-located or operating in conjunction with any other antenna or transmitter. 4.5.3 NCC ID Realtek Semiconductor Corp. Headquarters No. 2, Innovation Road II, Hsinchu Science Park, Hsinchu, 300, Taiwan, R.O.C. Tel: 886-3-5780211 Fax: 886-3-5776047 www.realtek.com.tw 11 Rev.1.0
This product uses the FCC Data API but is not endorsed or certified by the FCC