| submitted | available | document details (if available) | source link |
|---|---|---|---|
| June 11 2019 | June 11 2019 | Adobe PDF Library 15.0 |
| various | User manual | Users Manual | 971.94 KiB | June 11 2019 |
AUTOMATE | VT 1.0 ARC VENETIAN BLIND TILT MOTOR 433 MHZ BI-DIRECTIONAL ELECTRONIC LIMIT FAVORITE POSITION LEVELLING CONTROL SELECTABLE RPM AUTOMATE | ARC Venetian blind motor enables motorized tilting function of most 2 venetian blinds. Precisely control the openness of blind vanes or simply recall a favorite position. FEATURES:
Electronic Limits 433 MHz Bi-Directional RF Communication Favorite Position 3 x Selectable Rpm Jog or latch & Run Modes I 7 1 0 2 L R P A 0
. 1 V 1
-
T L I T
-
F R C D T M
. R T S N I NOTES 2 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA CONTENTS 1 ASSEMBLY 2 WIRING 2.1 Power Options 3 P1 BUTTON FUNCTIONS 3.1 Motor State Test 3.2 Motor Configuration Options 4 INTIAL SET-UP 4.1 Pair Motor with controller 4.2 Check motor direction 4.3 Set limits 5 ADJUSTING LIMITS 5.1 Adjust upper limit 5.2 Adjust lower limit 6 ADDING OR REMOVING CONTROLLERS AND CHANNELS 6.1 Using motor P1 button 6.2 Using a pre-existing controller 7 FAVORITE POSITIONING 7.1 Set favorite position 7.2 Send shade to favorite position 7.3 Delete favorite position 8 SLEEP MODE 8.1 Enter sleep mode 8.2 Exit sleep mode 9 TROUBLESHOOTING 5 6 6 7 7 7 8 8 8 9 10 10 10 11 11 11 12 12 12 12 13 13 13 14 3 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA SAFTEY INSTRUCTIONS WARNING: Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturers liability and warranty. Do not expose to moisture or extreme temperatures. Do not allow children to play with this device. Use or modification outside the scope of this instruction manual will void warranty. Installation and programming to be performed by a suitably qualified installer. For use within tubular blinds. Ensure correct crown and drive adaptors are used for the intended system. Keep antenna straight and clear from metal objects Do not cut the antenna. Use only Rollease Acmeda hardware. Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation. Ensure torque and operating time is compatible with end application. Do not expose the motor to water or install in humid or damp environments. CAUTION Motor is to be installed in horizontal application only. Do not drill into motor body. The routing of cable through walls shall be protected by isolating bushes or grommets. Ensure power cable and aerial is clear and protected from moving parts. If cable or power connector is damaged do not use. Important safety instructions to be read prior to operation. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product. Keep remote controls away from children. Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. Keep motor away from acid and alkali. Do not force the motor drive. Keep clear when in operation. Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately. 5005833 4 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 1 ASSEMBLY The Automate Venetian Blind tily motor works with most 2 blind headrail systems. Step 1. Insert the motor / cradle assembly completely into the drive side of the 2 headrail Step 2. Ensure at least inch of the tilting drive Shaft is inserted into the motor.
(max depth is Optional Shaft adapters may be required) Step 3. Remove motor, mark and drill hole where P1 button can be accessed. Step 4. Reinstall motor, ensuring power cord and Antenna extend freely from the headrail cap. 5 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 2 WIRING 2.1 Power Options Automate DC motors are powered from a 12V DC power source. AA Battery wands, re-chargeable battery packs and A/C power supplies are available, with a variety of quick connect extension cords. For centralized installations, power supply range can be extended with 18/2 wire (not available through Rollease Acmeda). During operation, if voltage drops to less than 10V, the motor will beep 10 times to indicate a power supply issue. Motor will stop running when the voltage is lower than 7V and it will resume again when the voltage is greater than 7.5V. DC Power Supply Power Supply Motor MTBWAND18-25 Battery Tube for 18/25mm DCRF (no Battery) Mtrs
(inc Mt clips) MTDCPS-18-25 Power Supply for 18/25-CL/Tilt DCRF (no Bttry) Mtr MTBPCKR-28 Rechargeable Wand Extension Cables MTDCRF18-0.2 - 18mm DCRF Motor, .2N/80 MTDCRF25-1.1 25mm DCRF Motor, 1.1N/40r MTDCRF-TILT-1 MTDCRF-CL-0.6-50 MTDCRF18-0.2 - 18mm DCRF Motor, .2N/80 MTDCRF25-1.1 25mm DCRF Motor, 1.1N/40r MTDCRF-TILT-1 MTDCRF-CL-0.6-50 MTDCRF18-0.2 MTDCRF25-1.1 MTDCRFQ28-2 MTDCRF-TILT-1 MTDCRF-CL-0.6-50 Length MTDC-CBLXT6 DC Battery Motor Cable extender 6 / 155mm 6 inch MTDC-CBLXT48 DC Battery Motor Cable extender 48 / 1220mm 48 inches MTDC-CBLXT96 DC Battery Motor Cable extender 96 / 2440mm 96 inches Ensure cable is kept clear of fabric. Ensure antenna is kept straight and away from metal objects. 6 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 3 P1 BUTTON FUNCTIONS 3.1 Motor State Test This table describes the function of a short P1 button press/release(<2 seconds) depending on current motor configuration. P1 Press Short Press then Release
(<2 sec) Condition Function Achieved Visual Feedback Audible Feedback Function Described If limit is NOT set None No Action None No Action If limits are set If motor is in Sleep Mode &
limits are set
(Refer to Sec.10) Operational control of motor, run to limit. Stop if running Wake and control Motor runs None Motor wakes and runs in a direction None Operational control of motor after pairing and limit setting is completed first time Motor is restored from Sleep mode and RF control is active 3.2 Motor Configuration Options The P1 Button is utilized to administer motor configuration as described below and beginning in Section 4. Hold P1 P1 Activate Pairing Mode Approx. Motor Response RELEASE P1 Sleep Mode Approx. Motor Response RELEASE P1 Reverse Direction Approx. Motor Response RELEASE P1 Reset To Factory Settings Approx. Motor Response 7 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 4 INTIAL SET-UP 4.1 Pair Motor with controller Select channel on controller.
(Disregard if using single channel controller) Hold P1 button on motor Hold STOP on controller IMPORTANT Consult user manual for your controller for information on selecting channel. Motor Response Motor Response RELEASE P1 Motor is now in setup mode and ready for setting limits. 4.2 Check motor direction To check travel direction of shade, press UP or DOWN on controller. To reverse shade direction, hold both UP and DOWN until motor responds Motor Reponse Reversing motor direction using this method is only possible during initial set-up, prior to first time limit setting, or after a re-set of motor 8 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 4.3 Set limits IMPORTANT Damage to shade may occur when operating motor prior to setting limits. Attention should be given. To save upper limit, hold UP and STOP. Move shade to the desired highest or lowest position by pressing the UP or DOWN buttons on controller. To save lower limit, hold DOWN and STOP. Quick Press = Step Long Press = Continuous Travel Motor Response Approx. 5 SECS Initial set-up is now complete 9 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 5 ADJUSTING LIMITS 5.1 Adjust upper limit Hold UP and STOP on Controller until the motor responds. Move shade to the desired upper position by pressing the UP or DOWN button. To save upper limit, hold UP and STOP until the motor responds. Motor Response Motor Response Approx. 5 SECS 5.2 Adjust lower limit Hold DOWN and STOP on controller. Move shade to the desired lowest position by pressing the UP or DOWN button To save lower limit, hold DOWN and STOP. Motor Response Motor Response Approx. 5 SECS 10 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 6 ADDING OR REMOVING CONTROLLERS AND CHANNELS 6.1 Using motor P1 button Hold P1 button on motor head. Hold STOP on controller to add or remove Motor Response Motor Response RELEASE P1 Approx. 6.2 Using a pre-existing controller A= Existing controller or channel (to keep) B= Controller or channel or add or remove Press P2 on existing controller. Press P2 on existing controller. Press P2 on new controller. Motor Response Motor Response Motor Response IMPORTANT Consult user manual for your controller or sensor. 11 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 7 FAVORITE POSITIONING 7.1 Set favorite position Move shade to the desired position by pressing the UP or DOWN button on the controller. Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response 7.2 Send shade to favorite position Hold STOP on controller. Approx. 7.3 Delete favorite position Press P2 on controller. Press STOP on controller. Press STOP on controller. Motor Response Motor Response Motor Response 12 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 8 SLEEP MODE 8.1 Enter sleep mode Sleep mode is utilized to prevent a motor from moving during shipping of a fabricated shade. Hold P1 button on motor head. Motor Response Approx. Motor Response RELEASE P1 8.2 Exit sleep mode Exit sleep mode once shade is installed. PRESS & RELEASE P1 button on motor head. Motor Response Approx. Motor Response MOTOR RUNS TO LIMIT 13 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA 9 TROUBLESHOOTING Problem Motor is not responding Cause A / C power supply not plugged in. Check motor to power cable Remedy Battery in wand are depleted Power failure connection and AC plug. Replace 8xAA alkaline batteries. Check power supply to motor is connected and active Transmitter battery is discharged Replace battery Battery is inserted incorrectly into transmitter Check battery polarity Radio interference/shielding Receiver distance is too far from transmitter Incorrect wiring Unable to adjust or set limits. Remote is in a locked state. Cannot program a single Motor
(multiple motors respond) Multiple motors are paired to the same channel. Ensure transmitter is positioned away from metal objects and the aerial on motor or receiver is kept straight and away from metal Move transmitter to a closer position Check that wiring is connected correctly (refer to motor installation instructions) Change remote status to an unlocked state Always reserve an individual channel for programming functions SYSTEM BEST PRACTICE - Provide an extra 15 channel remote in your multi motor projects, that provides individual control for each motor for programming purposes Place all other motors into sleep mode (ref to P1 function overview
- section 3.2 and 10.1) 14 | Automate Programming Instructions | ARC Venetian Tilt Motor ROLLEASE ACMEDA This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +61 3 9355 0100 | F +61 3 9355 0110 Queensland Branch Unit 2/62 Borthwick Avenue, Murarrie QLD 4172 ROLLEASE ACMEDA USA 200 Harvard Avenue Stamford, CT 06902 6320 T +1 203 964 1573 | F +1 203 964 0513 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan
(Lombardia) Italy T +39 02 8982 7317 | F +39 02 8982 7317 info@rolleaseacmeda.com rolleaseacmeda.com 15 | Automate Programming Instructions | ARC Venetian Tilt Motor
This product uses the FCC Data API but is not endorsed or certified by the FCC