submitted | available | document details (if available) | source link |
---|---|---|---|
January 06 2016 | January 06 2016 | HT-SB38_SEC_EN.pdf GAK102328 Acrobat Distiller 10.1.16 (Windows) |
various | User Manual | Users Manual | 1.45 MiB | January 06 2016 |
ENGLISH MODEL HT-SB38 SOUND BAR HOME THEATER SYSTEM OPERATION MANUAL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. HT-SB38 Sound Bar Home Theater system consisting of HT-SB38 (sound bar system) and CP-SW38 (active subwoofer system). Note:
This product is recommended for at panel TV (LED, LCD and Plasma). Accessories The following accessories are included. Remote Control
(RRMCGA388AW01) HDMI Cable x 1
(QCNWGA078AWPZ) AC/DC adaptor x 2
(RADPAA100AWZZ) AC power cord x 2
(QACCDA005AWZZ) Pattern Paper
(TCAUHA034AWZZ) NFC tag x 1 Velcro tape (hook type) x 1 Velcro tape (loop type) x 2
(PSHEZA373AW01)
(GCASP9349AW01)
*TINSEA505AWZZZW*|
TINSEA505AWZZ
(PSHEZA372AW01) Printed in Malaysia 16C R MW 1 Note to CATV system installer:
FOR YOUR RECORDS
.............................. Model number
.............................. Serial number
.............................. Date of purchase Place of purchase .............................. Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other trademarks and their respective owners. trade names are those of The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Special Notes
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT RE-
MOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Explanation of Graphical Symbols:
-
-
-
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NOTE
-
-
-
-
Warning:
FCC Radiation Exposure Statement
-
E-1 Important Safety Instructions
-
-
-
-
-
-
Additional Safety Information
-
-
-
-
-
-
-
-
-
-
-
E-2 For U.S. customer only CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
"Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction. In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer. The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp. The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY(50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO. Model Specific Section Your Product Model Number & Description:
Warranty Period for this Product:
Additional Item(s) Excluded from Warranty Coverage
(if any):
Where to Obtain Service:
What to do to Obtain Service:
HT-SB38 Sound Bar Home Theater System
(Be sure to have this information available when you need service for your Product.) One (1) year parts and labor from the date of purchase. Non-functional accessories, supplies, and consumable items. At a Sharp Authorized Servicer located in the United States. To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP. Ship prepaid or carry in your Product to a Sharp Authorized Servicer. Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and packaged securely. TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP SHARP ELECTRONICS CORPORATION 1 Sharp Plaza, Suite 1, Mahwah, NJ 07495-1123 E-3
Hold the AC power plug by the head when removing it from the AC outlet, as pulling the cord can damage internal wires.
The AC power plug is used as a disconnect device and shall always remain readily operable.
Do not remove the outer cover, as this may result in electric shock. Refer internal service to your local SHARP service facility.
This unit should only be used within the range of 41F -
95F (5C - 35C).
SHARP is not responsible for damage due to improper use. Refer all servicing to a SHARP authorised service center. Warnings:
The supplied AC/DC adaptor contains no user serviceable parts. Never remove covers unless qualied to do so. It contains dangerous voltages, always remove mains plug from the main outlet jack before any service operation or when not in use for a long period.
The AC/DC adaptor supplied with the HT-SB38 must not be used with other equipment.
Never use an AC/DC adaptor other than the one specied. Otherwise, problem or serious hazards may be created.
The voltage used must be the same as that specied on this unit. Using a higher voltage is dangerous and may result in a re or other type of accident causing damage. SHARP will not be held responsible for any damage resulting from such usage.
In case of repairing, please bring the entire system set to the service center.
Volume control The sound level at a given volume setting depends on speaker efciency, location and various other factors. It is advisable to avoid exposure to high volume levels, which occurs while turning the unit on with the volume control setting up high, or while continually listening at high volumes. Precautions
General
Keep your equipment at least 4" (10 cm) of free space along the sides, top and back for proper ventilation. Table/floor 4" (10 cm) 4" (10 cm) 0" (0 cm) 4" (10 cm) Wall mount 4" (10 cm) 4" (10 cm) 4" (10 cm) 4" (10 cm) Wall mount bracket 4" (10 cm) 4" (10 cm) 9/16" (1.5 cm) 4" (10 cm) 4" (10 cm)
Use the unit on a rm, level surface free from vibration.
Keep the unit away from direct sunlight, strong magnetic elds, excessive dust, humidity and electronic/electrical equipment (home computers, facsimiles, etc.) which generate electrical noise.
Do not place anything on top of the unit.
Do not expose the unit to moisture, to temperatures higher than 140F (60C) or to extremely low temperatures.
If the unit does not work properly, unplug and plug it in again. Than turn on the unit.
In case of an electrical storm, unplug the unit for safety. E-4 Controls and indicators
Sound Bar Front Panel 1 3 4 5 6 2 8 7 9 7. Sound Mode Button 8. Volume Down / Up Button 9. NFC detection area 1. Bass Reex Duct 2. Woofer 3. DC In Jack 4. SW LINK (Subwoofer Link) button 1. Left Channel Speakers 2. Right Channel Speakers 3. On/Standby/Input/ Bluetooth Pairing Indicator 4. On/Standby Button 5. Input Button 6. Pairing Button
Subwoofer Front view Rear view 1 2 3 4
Sound Bar Rear Panel 1. Audio IN Terminal 2. Optical IN Jack 3. HDMI OUT (TV ARC) Jack 4. USB Terminal 5. HDMI IN 2 Jack 6. HDMI IN 1 Jack 7. DC IN Jack 1 2 5 3 4 6 7 E-5 Controls and indicators (continued) 1 2 3 4 5 6 7 8 9 19 10 11 12 13 14 15 16 17 18
Remote Control 1. TV Operation Button 2. Bluetooth Pairing Button 3. Display 4. Remote Control Transmitter 5. Sound Mode Button 6. Cursor Left/Fast Reverse/Skip Down button 7. Cursor Up/Play Mode Button 8. Cursor Right/Fast Forward/Skip Up Button 9. ON/STANDBY Button 10. Volume Up Button 11. 12. Menu Button 13. Input Select Button 14. Mute Button 15. Bass/Treble Button 16. Cursor Down Button 17. Play/Pause Button 18. Volume Down Button 19. DC IN Terminal Speaker Select Button
Display remote control To control the sound bar HT-SB38 comes with a wireless display remote control which uses Bluetooth to communicate instead of infra red which requires direct line of sight. You can control the sound bar from any direction or angle within 32 feet
(10 meters). To control SHARP TV This remote control still uses infra red to control SHARP TV. Point the remote control at the TV remote sensor to operate the TV. NOTE:
In case the remote control is lost or needs repairing, bring the entire system set to the service center.
Connecting the remote control The remote control and sound bar will link automatically
(wirelessly) as it is already pre-linked at the factory. If the link cannot be established, please set the connection by the following method. 1. Select PAIRING from the remote control menu. (Refer to select a menu on the remote control on page 14.) 2. CONNECTED will appear on the display when pairing is successful.
TV code selection The default TV code for the remote control is TV CODE 1. In case SHARP TV is not responding to TV operation button, change the code by selecting TV CODE from the remote control menu (Refer To select a menu on the remote control on page 14). TV Operation Buttons (Only SHARP TV):
On/Standby Button Input Select Button (TV) Sets the TV power to ON or STANDBY. Press the button to switch the input source. Channel Up and Down Buttons Switch up/
down the TV channels. Volume Up and Down Buttons Turn up/
down the TV volume. Note:
Some models of SHARP TV may not be operable. E-6 Sound bar preparation Make sure to unplug the AC power cord before in-
stalling the sound bar or changing the position. 2
To mount the sound bar on the wall Caution:
-
SHARP is not responsible for accidents resulting
from improper installation.
1-1/4 (32 mm) 3/8 (8-9 mm) Wall surface 1-1/4 (32 mm) 3/8 (8-9 mm) Wall surface 3
4
Driving screws SHARP designed the sound bar so you may hang it on the wall. Use proper screws (not supplied). See below for size and type. 1/8 (3.2 mm) 3/16
(5 mm) 3/8 (9 mm) 7/8 (Min. 22 mm) Installing the sound bar Wall surface Screw using screwdriver Wall surface 3/16 (4.5 mm - 5 mm) Gap from wall surface 5 1 -
21-5/8 (548 mm) 509 mm Wall surface 44 mm Pattern paper
(supplied) E-7 Falling prevention Safety wires (not supplied) are useful to prevent the sound bar from falling. When mounting on the wall Screw eye
(not supplied) Safety wires
(not supplied) Wall Sound bar When placing on the shelf/table Rack/
table Safety wires
(not supplied) Screw eye
(not supplied) Sound bar Screw eye
(not supplied) E-8 Placing the system Installation image:
TV SOUND BAR HOME THEATRE SYSTEM HT-SB35D Digital tuner DVD player Subwoofer System connection Notes:
The front panel of the sound bar is not removable. Caution:
Do not change the installation direction when the sound bar is turned on. Do not stand or sit on the sound bar or subwoofer as Do not allow any objects to fall into or to be placed in you may be injured. the bass reex duct. After checking all the connections have been made correctly, connect the AC power cord to the AC power input jack, then to the AC outlet. Using with the AC/DC adaptor 1 Plug the AC power cord into the AC/DC adaptor. 2 Plug the AC/DC adaptor cable into the DC INPUT jack on the sound bar and subwoofer. 3 Plug the AC power cord into an AC outlet. Notes:
Unplug the AC/DC adaptor from the AC outlet if the system will not be used for a prolonged period of time. Use only the supplied AC/DC adaptor. Using other AC/DC adaptor may cause an electric shock or re. Make sure to unplug the AC power cord before making any connections. AC/DC Adaptor Cable 2 AC power cord 1 AC outlet AC/DC Adaptor
(AC 100 - 240 V
~ 50/60 Hz) DC IN jack
(DC 19V) AC power cord 1 DC IN jack
(DC 19V) 2 AC/DC Adaptor
(AC 100 - 240 V ~
50/60 Hz) CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. AC outlet E-9 System connections (continued)
HDMI Connection Caution:
Turn off all other equipment before making this connection. The illustration below shows the ows of the signals. Audio and Video signal TV 1. Method 1 This connection is for HDMI TV with ARC (Audio Return Channel). TV To HDMI (TV ARC) input terminal DVD/Blu-ray Digital tuner DVD, Blu-ray disc player or similar To HDMI output terminal To HDMI OUT (TV ARC) output terminal Sound Bar To HDMI input terminal 2. Method 2 This connection is for HDMI TV without ARC (Audio Return Channel). TV To HDMI input terminal To audio output terminal To Headphone terminal DVD, Blu-ray disc player or similar To HDMI output terminal To HDMI OUT (TV ARC) output terminal Sound Bar To HDMI input terminal To select HDMI 1, 2 or TV ARC function (Source):
Press INPUT button repeatedly on the sound bar or remote control until HDMI 1, HDMI 2 or TV ARC appears on the display. Notes:
This sound bar supports HDMI which enables ARC (Audio the CEC. For SHARP LCD TV, it is named as AQUOS LINK.
The system will automatically power off if TV or similar Return Channel).
(with ARC).
To enable ARC make sure to use High Speed HDMI cable
This ARC feature requires TV that supports ARC. Refer the operation manual of the TV to determine which terminal supports ARC.
To listen to the sound from a non-ARC-compatible TV, connect the audio output from TV to this systems. (refer this page)
This sound bar can be operated (power on/off or volume up/
down) via a TV or similar component which supports HDMI CEC
(Consumer Electronics Control). If this does not work, it does not mean this system is faulty. Refer to the operation manual of the respective component on how to activate the CEC. Example: Go to the Menu of the component to search and enable the CEC. Different brands may have different naming for component which supports HDMI CEC, is turned off.
CEC is not available during Low power consumption mode.
To listen to the sound from this system, you will need to menu (refer page 14) or adjust the speaker select output settings within the TV menu. For details, refer to the operation manual of the TV.
If you are unable to select external speaker setting from the TV menu (E.g. For SHARP LCD TV, it is named as AQUOS AUDIO SP), turn the CEC OFF and ON again.
To enjoy 3D images or 4K content, this system must be connected to a 3D-compatible TV and components (3D BD player, etc.) via High Speed HDMI cables. Put on the 3D glasses, otherwise 3D images or 4K content may not be viewed properly.
If you want to use HDMI IN 1 jack, please use the supplied HDMI cable. E-10 Audio connections to TVs, DVD players, VCRs, etc.
Other connection (without HDMI) The illustration below shows the ows of audio and video signals. Audio signal Video signal TV DVD/Blu-ray Disc Player Notes:
Refer to the operation manual of the equipment to be connected.
Fully insert the plugs to avoid fuzzy pictures or noises.
Connecting via this method may disable TV internal speakers.
In some cases, a small background noise could emit from the sound bar, when you use the RCA audio output terminal connection from a TV-Set/DVD/Blu-ray Disc Player. In such case, please change the connection to the HDMI/ARC or headphone terminal connection. This effect depends on the used TV/DVD/Blu-ray Disc Player-
Brand, model and age, and it is not a quality matter from the sound bar. Digital tuner, etc.
Connecting a TV, or DVD player, etc. Connect to the TV using an optical digital cable or an audio cable. TV or To audio output terminals Audio cable (commercially available) To HEADPHONE terminal Note:
Make sure that the audio cable end with ferrite core is connected to the sound bar AUDIO IN terminal. A u d o i i s g n a l To AUDIO IN input terminals Blu-Ray/
DVD player/Digital Tuner Optical digital audio cable
(commercially available) To optical digital audio output terminal To OPTICAL IN
(optical) input terminal Sound Bar To select OPTICAL function:
Press the INPUT button repeatedly on the sound bar or remote control to select OPTICAL. To select AUDIO IN function:
Press the INPUT button repeatedly on the sound bar or remote control to select AUDIO IN. E-11 Remote control
Battery installation Use 2 AA size battery (UM/SUM-3, R6, HP-7 or similar). Batteries are not included. 1 Open the battery cover. 2 Insert the batteries according to the direction indicated in the battery compartment. When inserting or removing the battery, push them toward the battery terminals. 3 Close the battery cover. Caution:
Remove the battery if the sound bar will not be used for a long period of time. This will prevent potential damage due to battery leakage.
Do not use rechargeable battery (nickel-cadmium battery, etc.). bar to malfunction.
Installing the battery incorrectly may cause the sound
Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, re or the like. Notes concerning use:
Replace the battery if the operating distance is reduced or if the operation becomes erratic.
Periodically clean the transmitter on the remote control and the sensor on the sound bar with a soft cloth.
Exposing the sensor on the sound bar to strong light may interfere with operation. Change the lighting or the direction of the sound bar.
Keep the remote control away from moisture, heat, shock, and vibrations. Notes:
The battery indicator will not correctly display the remaining capacity for approximately 10 seconds after the power has been turned on.
The number of bars shown in the battery indicator may increase or decrease, depending on the operation being performed. This is normal.
The battery life and the operating time may be shortened by usage conditions, long periods of disuse, etc.
Test of the remote control Point the remote control directly at the remote sensor on the sound bar. The remote control can be used within the range shown below:
8 - 20
(0.2 m - 6 m) Remote sensor 15 15
USB connection To operate the remote control without battery power, connect a Micro USB cable (not supplied) to the remote control power terminal.
Connection of the USB cable to the remote control disconnect the batteries.
Checking the remaining amount of battery level The battery level is shown by the battery indicator during operation. Battery indicator Battery indicator To source power When the battery When the battery level is high level is high When the battery When the battery level is very low level is very low Caution:
The USB connection cannot be used to charge the remote control or as a media playback.
When the battery level is very low, Battery low will appear on the display.
Replace the battery with a new one.
When Battery low appears on the display, the power will be disconnected automatically. E-12 General control Make sure to enable the HDMI CEC when making HDMI connection. For details, refer to the operation manual of the TV.
To turn the power on Press the ON/STANDBY button on the sound bar or the button on the remote control.
The power turns on and the sound bar on/standby/
pairing/input indicator lights up according to the input source. If the power does not turn on, check whether the AC power cord is plugged in properly. Input source Bluetooth Others Indicator Blue. Violet.
The system will automatically power on if TV or similar component which supports HDMI CEC, is turned on. To set the sound bar to standby mode:
Press the ON/STANDBY button on the sound bar or the button on the remote control. The the sound bar on/standby/pairing/input indicator turns red. Notes:
A slight audio delay after TV is turned ON does not mean that the system is faulty. This is normal.
AQUOS speaker is enabled message will be displayed if SHARP LCD TV does not detect HT-SB38 during power on. However the message AQUOS audio with AQUOS LINK is enabled will be displayed soon as HT-
SB38 is detected. These messages may vary for other TV model.
Eco mode
The rst time the unit is plugged in, it will enter standby mode (ECO mode off). Sound bar indicator turns red.
To cancel the standby mode, perform the following method. Remote Control:
1. Select ECO MODE ON from remote control menu (Refer To select a menu on the remote control on page 14). The next time the unit is turned off it will enter the low power consumption mode (Sound bar indicator turns off). 2. To return to the standby mode, select ECO MODE OFF. The next time the unit is turned off it will enter standby mode. E-13 Sound Bar:
1. Press and hold the ON/STANDBY button during power on until the sound bar is turned off. The next time the unit is turned on and off again it will enter the low power consumption mode (Sound bar indicator turns off). 2. To return to the standby mode, perform step 1 above. The next time the unit is turned on and off again it will enter standby mode.
During standby mode, NFC function is activated once your device touches the supplied NFC tag when there is no HDMI connection.
Pairing with the Subwoofer The sound bar and subwoofer will link automatically
(wirelessly) when turned on as it is already pre-linked at the factory. Indication during power on Indicator on the sound bar lights up in violet or blue
(according to the input source) If the link cannot be established, please set the connection by the following method. During sound bar standby and subwoofer power off mode (AC power cord unplugged):
1. Press and hold the PAIRING button on the sound bar or on the remote control for more than 3 seconds. 2. Within 3 minutes, plug in the AC power cord of the subwoofer and turn the power on.
In case the link is still not established (Sound bar indicator blink), press and hold the SW LINK button at the back of the subwoofer until sound bar light up. Indication during pairing process Process During pairing Successful pairing Indicator Indicator will blink in violet Indicator turns red SW LINK Sound Bar Sound bar Remote Control Control Subwoofer Subwoofer Notes:
If a device such as microwave oven, wireless LAN card, Bluetooth device or any other device that uses the same 2.4GHz frequency near the system, some sound interruption may be heard due to interference.
The transmission distance of the wireless signal between the subwoofer and sound bar is about 32 feet (10 meters), but may vary depending on your operating environment. If a steel-concrete or metallic wall is between the subwoofer and the sound bar, the system may not operate at all, because the wireless signal cannot penetrate metal. Caution:
Keep the subwoofer away from water and moisture.
To get the optimum listening performance, make sure the area around the sound bar and subwoofer is clear of any obstacles. General control (continued)
To select a menu on the remote control 1. Press MENU button. 2. To select a menu, press button, then press or or button to select an option in the desired 4. To select another menu, press button and repeat steps button. 3. Press menu. 2 to 3 above. Level/Mode Menu/
Function 3D AUDIO AV SYNC APC SW LEVEL ECO MODE ECO MODE ON PAIRING 3D AUDIO 0 AV SYNC 0 5 MIN
-5 1 1 10 MIN
-4 ..... 0 2 2 15 MIN 3 20 MIN
+4
+5 OFF To link the remote control and sound bar manually. TV CODE 1 Displays remote control and software version 2 TV CODE VERSION
Volume auto fade-in If you turn off and on the sound bar with the volume set to 20 or higher, the volume starts at lower level and fades in to the last set level.
Volume control Sound bar operation:
Press the VOLUME +
button to increase the volume and the VOLUME button for decreasing. Remote control operation:
Press the VOL. + button to increase the volume and the VOL. button to decrease the volume. MAX MIN
..... 99 2 1
Muting The volume is muted temporarily when pressing the MUTE button on the remote control. Press again to restore the volume. Note:
When the sound bar is turned off and back on again, muting is cancelled.
Sound Mode To change to a different mode, press the SOUND MODE button repeatedly on the sound bar or remote control until the desired sound mode is displayed.
Bass and Treble Control (remote control) Bass Control 1. Press the BASS/TREBLE button to select bass. 2. Within 5 seconds, press the VOL. (+ or ) or button to adjust the bass.
/
Treble Control 1. Press the BASS/TREBLE button repeatedly to select treble. 2. Within 5 seconds, press the VOL (+ or ) or button to adjust the treble.
/
Subwoofer level control (remote control) To increase or decrease the Subwoofer level, select SW LEVEL from the remote control menu. Notes:
When sound from the speaker is distorted, decrease
.....
+5
+4 5 4 the subwoofer level.
When changing the subwoofer level, the output level of the subwoofer is also changed.
AV SYNC level control (remote control) To increase or decrease the AV sync level, select AV SYNC from the remote control menu. 0
+1
.....
+3
Speaker output selection
(HDMI connection) (remote control) button on the remote control until TV Press SPEAKER or SOUND BAR SPEAKER appears on the display to toggle sound output between this sound bar or TV.
Function HDMI 1 HDMI 2 BLUETOOTH TV ARC OPTICAL AUDIO IN Press the INPUT button repeatedly on the sound bar or remote control to select the desired input source. Note:
The backup function will protect the memorized function mode for a few hours should there be a power failure or the AC power cord becomes disconnected. CINEMA MUSIC GAME SPORT NEWS NIGHT BYPASS
(for cinema sound effect)
(for standard sound effect)
(for game sound effect)
(for sport broadcasting)
(for news)
(for night)
(for at sound effect) E-14 General control (continued)
APC (Auto Power Off Control) (remote control) This sound bar can be set to turn off automatically if no signal or connection is detected. (During Audio In, HDMI, Optical In or USB function) 1. Select APC from the remote control menu to adjust the time. 2. The sound bar will enter the power standby mode automatically if no signal is detected after the preset time has elapsed.
Auto power on During the stand by mode, the unit will automatically power on if it detects audio signal from AUDIO IN, OPTICAL IN or when the BLUETOOTH connection has been set up between the sound bar and your device. They will remain connected if there is no HDMI connection. Note:
This function is not applicable during demonstration mode off.
Auto power off function The unit will enter eco mode on/off if:
Bluetooth:
- No connection for 1 minute.
- In the pause or stop mode and no incoming signal from device after approximately 15 minutes.
Audio Return Channel (ARC)
(Audio Return Channel submenu) The audio return channel (ARC) function enables an HDMI ARC-capable TV to send the audio stream to the HDMI OUT jack of the receiver. To use this function, you must select the TV ARC input and your TV must supports the ARC.
3D sound mode 3D creates 3D sound through speakers regardless of the type of sound source, whether it is stereo or multichannel. It simulates sound transmission characteristics using digital signal processing to create a widening effect on the sound in the ambient space around the sound source. By using this technology, multichannel surround sound can be produced from 2.1ch source. Select the desired 3D sound from the menu 3D AUDIO 1 :
Sound effect that emphasizes 3D sound. 3D AUDIO 2 :
Sound effect that maintains the 3D sound and improve vocal clarity. 3D AUDIO 0:
3D sound effect off. This product incorporates decoders supporting the Dolby Audio system. Dolby Audio One of the digital audio systems for theatrical use. You can also enjoy the stereophonic effect in the home theater system. Lights up when detecting Dolby Audio signal. This is a general term for digitally encoded audio signals on a CD or DVD. This sound bar lets you enjoy playback of digital signals from sources such as CD or DVD. PCM
(Pulse Code Modulation) E-15 Bluetooth one touch connection via NFC
About NFC technology Near Field Communication (NFC) is a set of standards for devices (smartphones/tablets) to establish radio communi -
cation with each other by touching/tapping them together or bringing them into close proximity. Using NFC in this product simplies the pairing method of Bluetooth connectivity.
This audio system supports NFC-enabled device with Android 4.1, Jelly Bean and higher.
For device with a lower Android version, refer the operation manual of the device for recommended app (application). Unlike other wireless technology, NFC requires no discovery or pairing. Simply tap the source device to the NFC detection area on the sound bar to instantly enjoy seamless connectivity between your smart device and the audio system.
NFC detection area NFC detection area location may vary depending on the device (smartphone / tablet). Refer operation manual of the device for detail. N o t h h O e t o S w it c B l u S e a r c h /
Pairing s c a n M a n u a l B luetooth setting Connect NFC detection area Or HT-SB38 NFC tag
(during standby mode) A Bluetooth audio source device
(smartphone /
tablet).
NFC tag setup 2 Peel the separator off the velcro tape (hook type) and stick it to the rear of the NFC tag. Then place the tag onto the desired location. Separator Velcro tape
(hook type) Rear view of the NFC tag The NFC tags can be placed anywhere convenient to you. The velcro tapes supplied will help to secure the tags onto the desired location. Caution :
Make sure that the NFC tag is placed on a at and level surface.
If you choose not to use the velcro tape, do not place the NFC tag near metal surface to avoid connection interference during tagging. Important:
NFC tag provided has unique ID for each sound bar.
SHARP will not be held liable for the damages caused by rewriting the tags. Keep all small parts away from children as they may be accidentally swallowed. 1 Peel the separator off the velcro tape (loop type) and stick it on a desired surface. Separator Velcro tape (loop type) E-16 Bluetooth one touch connection via NFC (continued)
NFC connection for audio playback Check that:
Your device (smartphone / tablet) has an NFC function.
NFC function on your device is turned on.
Screen lock function of the device is off.
This unit is not in Eco mode. 1 Touch your device to the NFC detection area on the sound bar or supplied NFC tag. NFC detection area NFC tag Or 2 A pop-up window asking whether to proceed with the Bluetooth connection appears on the device. Select
<YES>.
The connected message appears when the connec-
tion is complete. 3 Playback will start automatically. Otherwise, press play (on remote control or source device).
Sound will be heard from the speakers of this unit via audio streaming.
Your device must be within 32 feet (10 meters) from the sound bar. Bluetooth operation buttons (remote control only) Press to play or pause. Press to skip up. Press and hold to fast forward. Press once to restart the current track. Press twice to skip down. Press and hold to fast reverse. Notes:
To disconnect, simply touch your device to the NFC detection area on the subwoofer or NFC tag again.
To listen to audio via Bluetooth connectivity without NFC tag - refer Pairing with other Bluetooth source devices on page 18.
It takes about 6-8 seconds for a Bluetooth enabled device
(eg. smartphone) to establish Bluetooth connection with this unit via NFC or manual connection. Listening to Bluetooth enabled devices
Bluetooth Bluetooth wireless technology is a short-range radio technology that enables wireless communication between various types of digital devices, such as mobile phone or computer. It operates within a range of about 32 feet
(10 meters) without the hassle of having to use cables to connect these devices. This unit supports the following:
Communication System: Bluetooth Specication version 2.1 Bluetooth + Enhanced Data Rate (EDR). Support Prole : A2DP (Advanced Audio Distribution Prole) and AVRCP (Audio/Video Remote Control Prole) Notes when using unit with a mobile phone
This unit cannot be used to talk over the telephone even when there is a Bluetooth connection made to a mobile phone.
Please refer to the operating manual supplied with the mobile phone for details on operation of your mobile phone while transmitting the sound using a Bluetooth connection. E-17
Pairing Bluetooth devices Bluetooth devices need to be initially paired rst before they can exchange data. Once paired, it is not necessary to pair them again unless:
Pairing is made with more than 20 devices. Pairing can only be made one device at a time. This unit can be paired to a maximum of 20 devices. If subsequent device is paired, the oldest device paired, will be deleted and replaced with the new one.
This unit is reset. All pairing information is deleted when unit is reset.
Pairing information is deleted while re-pairing, etc. Listening to Bluetooth enabled devices (continued)
Listening to the sound Check that:
The source device Bluetooth functionality is ON.
Pairing of this unit and the source device is completed.
Unit is in connected mode. 1 Press the ON/STANDBY button on the sound bar or the button on the remote control. 2 Select the Bluetooth function (on the sound bar or remote control). 3 Start the Bluetooth connection from the Bluetooth stereo audio source device. 4 Start Bluetooth streaming playback. Notes:
For various Bluetooth operations, refer NFC connection for audio playback on page 17.
If the source device has an extra bass function or equalizer function, set them to off to avoid sound distortion. Note:
Make the Bluetooth connection again if the source device is not turned on, or its Bluetooth functionality is off or is in sleep mode.
To disconnect the Bluetooth device Perform any of the followings. Disconnect the Bluetooth connection on the audio source device. Refer the operating manual supplied with the device. Turn off the Bluetooth stereo audio source device. Turn off this unit. Note:
The volume of this unit may not be controlled as intended depending on the device. Indicators on the sound bar display:
Indicator (blue) Bluetooth status Blinks Lights up No indication In waiting or pairing mode Connected Unconnected However, the indication status is not displayed during standby mode or in other function.
Pairing with other Bluetooth source devices 1 Press the ON/STANDBY button on the sound bar or button on the remote control. 2 Select the Bluetooth function (on the sound bar or the remote control). BLUETOOTH appears on display. 3 Press PAIRING button on the sound bar or remote control. Notes:
Place the devices to be paired within 3 feet (1 meter) of each other when pairing.
Some source devices are unable to display lists of detected devices. To pair this unit with the source device, refer to the source device operating manual for details. 4 Select HT-SB38 SHARP from the source list. If Passcode* is required, enter 0000.
* Passcode may be called PIN Code, Passkey, PIN number or Password. 5 Pairing indicator will light up in blue once the unit is successfully paired with the source device. (Pairing information is now memorized in the unit.) Some audio source devices may connect with the unit automatically after pairing is completed, otherwise follow the instructions in the source device operating manual to start connection. 6 Start Bluetooth streaming playback. Notes:
If a device such as microwave oven, wireless LAN card, Bluetooth device or any other device that uses the same 2.4 GHz frequency near the system some sound interruption may be heard.
The transmission distance of the wireless signal between the device and the sound bar is about 32 feet
(10 meters), but may vary depending on your operating environment. If a steel concrete or metallic wall is between the device and the sound bar, the system may not operate at all, because the wireless signal cannot penetrate metal.
If this unit or the source device is turned off before Bluetooth connection is completed, pairing will not be completed and the pairing information will not be memorized. Repeat step 1 onwards to start pairing again.
To pair with other devices, repeat steps 1 - 5 for each device. This unit can be paired to a maximum of 20 devices. If subsequent device is paired, the oldest device paired, will be deleted and replaced with the new one.
Once a device is ousted or deleted from the pairing list, the pairing information for the device is also deleted. To listen to the sound from the device again, it needs to be re-paired. Perform steps 1 - 5 to pair the device again. E-18 Listening to USB mass storage device/MP3 player
SHARP cannot guarantee that all USB memory devices will work on this audio system.
USB cable is not recommended for use in this audio system to connect to USB memory device. Use of the USB cable will affect the performance of this audio system.
This USB memory cannot be operated via USB hub.
The USB terminal in this unit is not intended for a PC connection but is used for music streaming with a USB memory device.
External HDD-storage cannot be played back via USB terminal.
If the data inside the USB memory is large, it may take longer time for the data to be read.
This product can play WMA and MP3 les. It will automatically detect the le type being played. If unplayable le is played on this product, the le will be automatically skipped. This will take a few seconds.
This product relates to USB mass storage devices and MP3 players. It may however face some irregularities due to various unforeseen reasons from some devices. Should this happen, turn off the unit and then turn it on again.
This unit only supports MPEG-1 Audio Layer-3 format.
(Sampling Frequency is 32, 44.1, 48kHz)
Playback order for MP3 les may differ depending on the writing software used during le download.
Bitrate which is supported by MP3 is 32~320 kbps, WMA is 64~160 kbps.
For MP3/WMA les, please put .MP3 .WMA extension. Files cannot be played back if there is no MP3/WMA extension.
Copyright protected WMA les cannot be played back.
Maximum total number supported for MP3/WMA les is 999. However, it is advisable to playback a media with a small amount of MP3/WMA les to maximize playability. Repeat play button repeatedly to select REPEAT ONE. Repeat play can play one track or all tracks. To repeat one track:
Press the To repeat all tracks:
Press the To cancel repeat play:
Press the Caution:
After performing repeat play, be sure to press the Otherwise, the device will play continuously. button to select NORMAL and button repeatedly to select REPEAT ALL. disappears.
/ button. Random play button repeatedly to select RANDOM. The tracks on the device can be played in random order automatically. To random play all tracks:
Press the To cancel random play:
Press the Notes:
button to select NORMAL.
Note:
This product is not compatible with MTP and AAC le systems from USB mass storage device or MP3 player.
To play back USB/MP3 player 1 Select the USB function (on the sound bar or remote control. USB appears on the display). 2 Playback will start automatically. Otherwise press
/ . 3 Select desired le to be played back by pressing the or button.
Title, Artist and Album name are displayed if they are recorded in the USB memory device.
Display content can be changed by pressing the button.
Note:
To pause playback:
Press the / button.
Various USB functions Function Remote control Operation Track up/
down Press in the playback or pause mode. If you press the button in the pause mode, press the
/ button to start the desire track. Press and hold down in the playback mode. Release the button to resume playback. Fast forward/
reverse Note:
Fast forward/reverse is invalid when playing back a variable bitrate le.
button to pause playback.
To remove USB memory device 1 Press the 2 Unplug USB memory device from the USB terminal. Notes:
SHARP will not be held liable for the loss of data while the USB memory device is connected to the audio system.
Files compressed in MP3 and/or WMA format can be played back when connected to the USB terminal.
This USB memorys format supports FAT 16 or FAT 32. E-19 Troubleshooting chart Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorized SHARP dealer or service center.
General Symptom Possible cause
No sound is heard.
The sound from subwoofer is not well balanced.
Power turns off suddenly.
Noise is heard during playback.
When a button is pressed, the sound bar does not respond.
The power is not turned on.
3D images and 4K content not displayed on the TV.
Background noise appears when connecting with RCA audio output terminal connection from a TV-set/
DVD/Blu-ray Disc Player.
Wireless connection cannot be established.
Is the input signal (selection) set properly?
Is the volume level set to MIN?
Is muting activated?
Is HDMI compliant equipment being used?
Is the HDMI cable connected correctly?
Connect the HDMI cable correctly and then perform the reset procedure. (refer page 20)
Do not connect or disconnect an HDMI cable while power is on. This may lead to operation problems.
Is the subwoofer level set to the minimum or maximum level?
Is the HDMI cable connected correctly? Connect the HDMI cable correctly and then perform the reset procedure.
Move the speaker away from any computers or mobile phones.
Set the sound bar to the standby mode and then turn it back on.
Is the sound bar unplugged?
The protection circuit may be activated. Unplug and plug in the power cord again after 5 minutes or more.
Depending on the TV and Video component, 3D images and 4K content may not be displayed. Check the operation manual of the respective component.
HDMI cable not support 3D images and 4K content.
Please change to HDMI/ARC or headphone terminal from TV-Set/
DVD/Blu-ray Disc Player. This effect may occur depending on TV/DVD/Blu-ray Disc Player-
Brand, model and age, and it is not the sound bar problem.
Check the distance between the sound bar and subwoofer (less than 32 feet (10 meters)).
Make sure there is no other wireless devices near the unit. E-20 Symptom Possible cause
Wireless connection cannot be established.
Make sure there is no obstacles
(especially metal) blocking between the sound bar and subwoofer.
Manually re-link the sound bar and subwoofer (refer page 13).
NFC / Bluetooth Symptom Possible cause
The unit is too far from the Bluetooth stereo audio source device.
The unit is not paired with the Bluetooth stereo audio source device.
The unit is too near to a device that generates electromagnetic radiation.
There is an obstacle between the unit and the Bluetooth stereo audio source device.
Sound bar is not in Bluetooth pairing mode. Perform NFC connection for audio playback.
(Refer page 17.)
No sound is heard.
Bluetooth sound is interrupted or distorted.
NFC-enabled device cannot connect to Bluetooth via NFC tag.
Remote control Symptom Possible cause
The remote control does not operate properly.
The sound bar cannot be turned on with the remote control.
USB
Is the battery polarity correct?
Is the battery dead?
Is the distance or angle incorrect?
Are there any obstructions in front of the sound bar?
Is there a strong light shining on the remote sensor?
Is the remote control for another equipment used simultaneously?
The remote control is not connected with the sound bar.
Is the AC power cord of the sound bar plugged in?
Is the battery inserted?
The remote control is not connected with the sound bar. Symptom Possible cause
Device cannot be
There is no MP3/WMA le inside
Playback does not
The device is not properly plugged detected. start. the device. in.
A MTP device is plugged in.
The device contains AAC le only.
A copyright-protected WMA or false MP3 le is being played back. Troubleshooting chart (continued)
Condensation Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet or on the transmitter on the remote control. Condensation can cause the sound bar to malfunction. If this happens, leave the power on until normal playback is possible (about 1 hour). Wipe off any condensation on the transmitter with a soft cloth before operating the sound bar.
If problem occurs during operation When this product is subject to strong external interference
(mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following:
1. Set the sound bar to the standby mode and turn the power on again. 2. If the sound bar is not restored in the previous operation, unplug and plug in the sound bar again, and then turn the power on.
Factory reset, clearing all memory Make sure to disconnect all output and input cables attached to the sound bar before performing the factory reset. 1. Press the ON/STANDBY button on the sound bar to enter the power standby mode. 2. While pressing the SOUND MODE button, press and hold the ON/STANDBY button until RESET appears. 3. Press the ON/STANDBY button again. (PAIRING indicator will turn red) Maintenance
Cleaning the cabinet Periodically wipe the cabinet with a soft cloth. Caution:
Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It may damage the cabinet nish.
Do not apply oil to the inside of each component. It may cause malfunctions. Error indicators and warnings When you fail to perform operations properly, the following messages are displayed on the sound bar. Display Meaning Error indicator
(blinks red)
When the protection circuit is activated.
(*): Should the same message appear even if the speaker is unplugged and plugged in, or is set to the standby mode and on again, contact your local dealer where you purchased the sound bar. Caution:
This operation will erase all data stored in memory. E-21
USB (MP3 / WMA) USB host interface
Complies with USB 1.1 (Full Speed)/2.0 Mass Storage Class. Support le Bitrate support Other
Support Bulk only and CBI protocol.
MPEG 1 Layer 3
WMA (Non DRM)
MP3 (32 ~ 320 kbps)
WMA (64 ~ 160 kbps)
Maximum total number of MP3/
WMA les is 999. File system support
Support USB devices with FAT 16/ FAT 32.
Subwoofer Power source DC IN 19V 3.42A: AC/DC adaptor
(AC 100 - 240V ~ 50/60Hz) 10 W Power consumption Output power RMS: Total 60 Watts 30 Watts per channel into 6 ohms at 1 kHz, 10% total harmonic distortion FTC: Minimum 23 watts per channel into 6 ohms at 100 Hz to 20 kHz, 1%
total harmonic distortion Subwoofer system 5 - 1/8 (13 cm) woofer Width: 7 - 3/8 (188 cm) Height: 11 - 1/8 (282 cm) Depth: 11 - 3/4 (299 cm) 6.6 lbs. (3.0 kg) Type Dimensions Weight Specications As part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement without prior notice. The performance specication gures indicated are nominal values of production unit. There maybe some deviations from these values in individual unit.
Sound Bar Power source DC IN 19V 3.42A: AC/DC adaptor Power consumption Dimension
(AC 100 - 240V ~ 50/60Hz) 20 W Width: 54 - 9/16 (1386 mm) Height: 2 - 15/16 (74 mm) Depth: 2 - 11/16 (68 mm) 7.9 lbs. (3.7 kg) Weight Output power RMS: Total 60 watts Output terminal Input terminal 500 mV / 47 k Type Bluetooth Frequency band Compatible Bluetooth Prole Maximum input power Rated input power Impedance RMS:
Front Left/Right:
30 watts per channel into 6 ohms at 1 kHz, 10% total harmonic distortion FTC:
Front: (Left/Right):
Minimum 20 watts per channel into 6 ohms at 120 Hz to 20 kHz, 1% total harmonic distortion HDMI output: (audio/video support up to 4K) x 2 Optical digital input (OPTICAL):
Square type x 1 HDMI input: (audio/video support up to 4K) x 1 2 Way speaker system 2 -1/4 (5.7 cm) woofer 1 (2.5 cm) Soft Dome 2.400GHz - 2.480GHz A2DP (Advanced Audio Distribution Prole), AVRCP (Audio/Video Remote Control Prole) BLUETOOTH 4.0 BLE (REMOTE CONTROL) Bluetooth 2.1 +EDR 60 W 30 W 6 E-22
This product uses the FCC Data API but is not endorsed or certified by the FCC