CBAP210A RF MODULE User manual

 

User manual 1. Functional Description CBAP210A is the module for BLE at embedded and Digital appliance applications. It is based on Airoha AB1611 solution which comprises single chip with integrated BLE 5.0 2. Features BLE (Version 5.0, only supports 1 Mbps) Supports Adaptive Frequency Hopping On chip support for serial peripheral interface (master and slave modes) Compact dimension: 3 5 mm x 2 0 mm / H max: 4. 8 mm Applicable test standard: FCC Part 15 Subpart C, 15.247 Host Interfaces: UART Interface RoHS compliant PCB Pattern antenna, 5.60 dBi Number of channels: 40 ch Supply voltage range

VCC 5V (4.5V ~12V) Power Consumption

200mW 3. Electrical Characteristics Absolute Maximum Ratings Symbol VIN Parameter DC supply voltage Min.

Max. 12 V Unit V Power Consumption Tx mode (Max current) Parameter Conditions Min. Nom. Max. Unit TX Power 5V, 0dBm(+/-5dB) Tx Power 40 mA Recommended Operating Conditions Symbol Parameter Conditions Min. Nom. Max. Unit VIN Top DC supply voltage from HOST Operating temperature(Ambient)

+4.5

-20

+5

+13.2V

+50 V C Environmental Characteristics Symbol Parameter Conditions Min. Max. Unit ESD Top Tstg Electro-static discharge voltage Operating temperature Storage temperature HBM

-4K

-20

-30

+4K

+85

+85 V C C 4. RF Specifications at each antenna port except antenna. All measurements are made under nominal supply voltage, room temperature, and conducted conditions Parameter Conditions Frequency Range 2402+K*2MHz (K=0~39) Min 2402 Typ.

Max 2480 Unit MHz Receiver Sensitivity (PER) RSSI Value Transmitter Output Power ICFT Frequency Drift Drift rate Frequency Deviation PER 30.8%

TCR Value

(TCB RSSI Calibration Value) DUT RSSI Value

(TRC Value-20) < RSSI < (TRC Value+20) Max. Tune-up Average Power Avg

(payload sequence 00001111) Max

(payload sequence 10101010)

30

-150

-50

225 185

-94 50 1.0

dBm 70

150 50 20 275

dBm kHz kHz kHz kHz/50us 1) FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2) FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3) FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 4) FCC Radiation Exposure Statement :

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 1) Industry Canada Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le pr sent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autoris e aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi, m me si le brouillage est susceptible d'en compromettre le fonctionnement. 2) Industry Canada Radiation Exposure Statement

(D claration dexposition aux radiations ):

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non con tr l . Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. The OEM integrator is responsible for the compliance to all the rules that apply to the product in to which this certified RF module is integrated. This module must be integrated into a device where the user cannot access the antenna connector and should not be able to remove or install the module. USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID: A3LCBAP210A ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX IC : 649E-CBAP210A ".