submitted | available | document details (if available) | source link |
---|---|---|---|
July 18 2013 | January 14 2014 | Adobe PDF Library 9.9 |
various | User manual | Users Manual | 632.66 KiB | July 18 2013 / January 14 2014 |
www.samsung.com Type E. AXXXXX 05/2013. Rev. 1.0 S Band User manual Contents English ................................................................................................................................1 This manuals images and content may differ from the product and is subject to change without prior notice. This product is only a health assisting device. It cannot be used for medical diagnostic purposes. E n g l i s h Safety precautions Do not use the device for anything other than its intended use Do not disassemble, modify, or repair the device Any changes or modifications to the device can void your manufacturers warranty. For service, take the device to a Samsung Service Centre. When using the device, mind the following:
Humidity and liquids may damage parts or electronic circuits. Do not store the device in hot areas. High temperature may cause damage to the device or shorten battery life. Do not drop the device or cause impacts to it. 1 Overview Indicator light Micro USB cover Setting button Check the product box for the following items: S Band, Micro USB cable, and user manual. The supplied items may vary depending on the region. 2 Charging the S Band The device has a rechargeable internal battery which is non-removable. Make sure they are fully charged before using it for the first time. E n g l i s h Use only Samsung-approved chargers. The travel adapter is sold separately. 3 1 Connect the travel adapter to the charging socket on the device. 2 Plug the travel adapter into the wall outlet. During charging, the indicator light will turn red. If the red indicator light flashes, unplug the travel adapter and plug it in again. 3 When fully charged, the indicator light turns green. Unplug the travel adapter from the device. When the main power turns off by the internal battery discharge, the accumulated data in the device cannot be restored. It is recommended to charge the device and sync with the smartphone before the battery is discharged. 4 Wearing the S Band Stretch out both sides of the device, and wear it on your wrist. Do not pull or stretch out the device too hard to avoid damage of the device. E n g l i s h 5 Pairing and Connecting with a smartphone Check physical activities and sleep patterns of daily life by connecting the device to the smartphone. To connect with the smartphone, the S Health application must be installed and launched on the smartphone. Connecting 1 Press and hold the setting button to enter Pairing mode until the indicator light 2 On the smartphone, launch the S Health application. 3 Tap Health board Walking mate S Band. flashes red, green, and blue for 30seconds. 6 4 Tap Scan to search for the device. 5 To pair with the smartphone, select the device from the list of available devices. Once pairing is complete, the blue or white indicator light stays for 3seconds, and then turns off. When the device is connected, the green indicator light flashes for 5seconds, and then turns off. E n g l i s h When the device is connected, the accumulated data can be managed on the smartphone. At first connection, the device starts counting steps. Press and hold the button for 3seconds to change into other function. Physical activities may not be measured accurately when the Wi-Fi and Bluetooth features are turned on at the same time. 7 Disconnecting 1 On the smartphone, launch the S Health application. 2 Tap Health board Walking mate S Band. 3 Tap Disconnect to disconnect the device from the smartphone. To check the disconnection, press the button. The blue or white indicator light stays for 30seconds. Reconnecting If the connection is lost while in use, press the button and tap Sync on the screen. Make sure the smartphones Bluetooth feature is activated. 8 Using modes The device can be used in two modes, walking mate and sleep monitor modes. In walking mate mode, steps can be counted, and sleep efficiency can be measured in sleep monitor mode. Changing and checking modes To switch between walking mate and sleep monitor modes, press and hold the button for 3seconds. It is possible to check modes of the device with the indicator lights colours. Walking mate: Press the button shortly, and then the blue indicator light flashes. E n g l i s h To ensure accurate counting, the device detects and counts the actual steps only when a certain motion continues for a while. Sleep monitor: Press the button shortly, and then the white indicator light flashes. 9 Forgetting and Resetting the S Band The device needs to be unpaired and reset data to pair with other smartphones. Forgetting the device 1 On the smartphone, launch the S Health application. 2 Tap Health board Walking mate 3 Tap OK to forget the device on the smartphone. Resetting the device Press and hold the button for 10seconds until the indicator light flashes red, green, and blue. S Band Unpair. 10 FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Statement (2.1091) This Equipment complies with FCC RF Radiation Exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. 11 IC Warning
"This device complies with Industry Canada licence-exempt RSS standard(s)."
Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas provoquer de brouillage, et (2)l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'encompromettre le fonctionnement. 12 IC Warning RF du FCC d'exposition aux radiations: Cet quipement est conforme l'exposition de la FCC rayonnements RF limites tablies pour un environnement non contrl. Cet appareil et son antenne ne doivent pas tre co-localiss ou fonctionnant en conjonction avec une autre antenne ou transmetteur. 12
This product uses the FCC Data API but is not endorsed or certified by the FCC