RP101V2 WiFi Repeater User manual

 

RP101v2 Wireless Repeater Manual Guide Introduction Overview The RP101v2 is Wireless Repeater, you can use this device to ex-

tend your existing Wireless network. Physical Details Figure 1: RP101v2 (Wireless Repeater) LEDs Power

(Green) On Power on / Normal operation. Off - No power. Page 1 Signal Quality

(Repeater

<-> AP) Signal Quality

(Repeater

<-> Cli-

ent) Wire-

less/WPS The connection between the RP101v2 and Root AP (access point) or Wireless Router. Off - No associate to Root AP (access point) or Wireless Router Green - The Wireless Link Rate is best Amber - The Wireless Link Rate is good Red - The Wireless Link Rate is poor The connection between the RP101v2 and IP camera or computer or mobile device. Off - No connection Green - The Wireless Link Rate is best Amber - The Wireless Link Rate is good Red - The Wireless Link Rate is poor Green On - Associate to Root AP (access point) or Wireless Router / Cli-

ent Off - Not associate to Root AP (ac-

cess point) or Wireless Router /

Client Flashing - Transmitting/Receiving Data Amber On - WPS failed (30 seconds) Off - No WPS action or WPS Suc-

ceed Flashing - WPS is processing (< 2 minutes) Page 2 Ethernet

(Green) Buttons WPS button Reset but-

ton On - Ethernet connection is active. Off - No Ethernet connection. Flashing - Data is being transmitted or received via the Ethernet Port. WPS button (for Push Button Method only) Establish a secure connection between the RP101v2 and Root AP (access point) or Wire-

less Router or IP camera / Client station WPS between RP101v2 and IP camera / Client Station:

Press and hold the WPS button, but not no more than 3 seconds (Quick Push) WPS between RP101v2 and Root AP (access point) or Wireless Router:

Press the WPS button and hold for greater than 8 seconds (Long Push) Reset to the factory default Press the reset button and hold for greater than 10 seconds, the system will reset to the factory default setting and reboot the system. LAN Port Use a standard LAN cable to connect the RP101v2 to the IP Camera Page 3 Setup To extend the range of your Wireless network, you must connect the RP101v2 to your existing Wireless network. You can connect with WPS button or with RP101v2s Easy Setup. Connect with WPS 1. Locate the RP101v2 near your Wireless router or access point while doing the configuration. 2. Make sure the Root AP (access point) or Wireless Router is on and working properly. 3. Plug the RP101v2 into the AC power slot, then the Power LED will remain on. 4. Press the WPS button on the side panel of the RP101v2 and hold for greater than 8 seconds. The WPS LED blinks. 5. Within two minutes, press the WPS button on your Root AP on the

(access point) or Wireless Router. The WPS LED RP101v2 lights solid green, the Signal Quality LED lights, and the RP101v2 is connected to your existing Wireless network. Note : If the Signal Quality LED again. does not light, try 6. On your computer or Wireless device, find the RP101v2 wire-

less network name. The wireless network name (SSID) of RP101v2 is same as Root APs. 7. Connect your existing Wireless devices to the RP101v2. Use the same wireless password that you use for your Root AP

(access point) or Wireless Router. Page 4 The RP101v2 (Wireless Repeater) is now ready for use. Connect with RP101v2s Easy Setup You can use a web browser to connect to the RP101v2 and set it up. 1. Locate the RP101v2 near your Root AP (access point) or Wireless Router while doing the configuration. 2. Make sure the Root AP (access point) or Wireless Router is on and working properly. 3. Plug the RP101v2 into the AC power slot, then the Power LED will remain on. 4. Use a Wireless network manager on the computer or mobile device to find and connect to the RP101v2. After the connection with the computer or mobile device is es-

tablished, the Signal Quality LED lights solid green. Note : The default wireless network name (SSID) of RP101v2 is RP101v2. 5. Open a web browser window from the same computer or mo-

bile device, and enter 192.168.0.250 in the address field. Enter admin for the user name and password for the password. The browser takes you directly to RP101v2 Easy Setup. Page 5 6. Select a Wireless network to extend and click the Next button. 7. In the Password (Network Key) field, type the network pass-

word (also called passphrase or security key) of Root AP

(access point) or Wireless Router. Page 6 8. In the Range Extender Name (SSID) field, type a name (SSID) for your RP101v2s Wireless network and click the Next but-

ton. 9. Click the Save button, then the RP101v2 will reboot and the settings are applied. Page 7 The RP101v2 (Wireless Repeater) is now ready for use. 10. Use a Wireless network manager on the computer or mobile device to connect to the RP101v2s newly created Wireless network. Example :

The wireless setting of RP101v2 is as below:

SSID : MyAP Security : WPA2-PSK (AES) Password (Network Key) : 1234567890 You also can use an Ethernet cable to connect a computer to the Ethernet port on the RP101v2. Page 8 Appendix A Specifications Network Camera Model Dimensions Wireless Repeater 40.7mm x 57mm x 91.7mm Operating Temperature 0 C to 40 C Frequency Band 2.4 G PHY Rate Up to 300 Mbps Storage Temperature

-20 C to 70 C Network Protocols TCP/IP, HTTP, DHCP, NTP Network Interface 1 Ethernet 10/100BaseT LAN connection Wireless interface IEEE 802.11n/802.11b/802.11g compatible, WEP 64/128 bit, WPA PSK, WPS US Domain LEDs Power Module 4 Built-in Input : AC 100-240V, 50/60 Hz Page 9 Regulatory Approvals FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the in-

structions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the fol-

lowing measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different Increase the separation between the equipment and receiver. from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Exam-

ple - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centime-

ters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

Page 10

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunc-

tion with any other antenna or transmitter. Page 11