H1500A YHS-113-IR (Smart Wireless Camera) User guide Users Manual

Downloading the App Scan the QR code of YiSmart App below and complete the installation. Getting Started 1. Plug in the power supply cable to the Micro USB port at the camera's back side. Connecting the camera to your phone 1. Please make sure the camera is ready to be connected to your mobile phone. The yellow light at the camera's front side should blink. 2. Wait few seconds until a yellow light starts to blink at the camera's front side. You can also download it at the App Sore/Google Play searching for YiSmart.

+ Before starting the camera, make sure the Wi-Fi network access is available. If the yellow light does not blink, use a clip to press the reset button at the camera's back side and wait the yellow light turns on. Insert a 8-32GB Micro SD card (CLASS4 or above) into the device to use... 2. Follow the app instructions to add the camera to your mobile phone. You can configure more cameras one by one. Thank you for choosing Yi Smart Camera Watching live video 1. Use the YiSmart App to watch live videos in your mobile phone. You can also record, save and edit images/videos. Hold to talk

(press the button) Photograph Folder History Playback

(Only available when Micro SD card is added-in) Capacity: 4-32GB Voice Monitoring Video recorder __Scanthe QR code QR code of YiSmart APP Switching Wi-Fi Network If you move the camera to a new location with different Wi-Fi network:

1. Press the reset button at the camera's back side with a clip and wait the yellow light turns on. 2. Connect the camera to your mobile phone through the app. Your videos stored in the TF card would not be affected. Attention 1. Place the camera in open areas with good Wi-Fi signals and away from metal objects. 2. Avoid place the camera behind furniture, near microwave oven or in locations with cables twisted together. Congratulations! You have complished all the Yi Smart Camera's configuration. Type: Yi Smart Wireless Camera Model: YHS-113 Input: 5V DC /1A(Micro USB) Power: 2.5W(Max) Reset Button Indicator Light This device complies with Part 15 of the FCC Rules / Industry Canada licence-

exempt RSS standard(s). Operation is subject to the following two conditions: (1) this devicemay not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) l'utilisateur de lappareil doit accepter tout brouillage radio lectrique subi, m me si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

+ Reorient or relocate the receiving antenna.

+ Increase the separation between the equipment and receiver.

+ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help. AddCamera The WiFi camera needs to connect Power on camera, wait until orange light flashes Be OOOO OOO Password Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment a la rgiementation d'industrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour fmetteur par Industrie Canada. Dans le but de rduire les risques de brouilage radiolectrique a fintention des autres utiisateurs, il faut choisir le type diantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.ir.e.) ne dpasse pas lintensit ncessaire 4 |'tablissement d'une communication satisfaisante. MPE Requirements To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation.To ensure compliance, operations at closer than this distance is not recommended. Les antennes install es doivent tre situes de facon a ce que la population ne puissey tre expose a une distance de moin de 20 cm. Installer les antennes de facon a ceque le personnel ne puisse approcher 4 20 cm ou moins de la position centrale de | antenne. La FCC des 6 ltatsunis stipule que cet appareil doit tre en tout temps loign d au moins 20 cm des personnes pendant son functionnement. CCK ig FCC ID:2AFIB-H1500A MSIP-CRM-stx-H1500A