ID115 Smart Bracelet Users Manual

 

2. USBDC 5V-500mA USB APP 1.VeryFit for heart rate 1 2 Apple Store VeryFit for heart rate Google Play Store360/

//

3. APP VeryFit for heart rate 1. APP 2. Device Activate & Charge Make sure power is working normally before initial use. In case device is under low battery, connect the device to the charger. Device will automatically boot up (please connect the USB in normal DC port (5V-500mA) for charging as below. The host should be separated from the strap when charging). Key Definitions:

Tapfunction switch Long Pressactivatemode switch USB charging port 2. APP

[//]

3. 4.

:

1.

. 2. 2. Remote Camera Shoot Mode Put the camera shoot ON in the APP, then device enter in remote shoot screen, control remote photograph shooting with following actions:

(Right slide screen / lift wrist sense / tap screen) to shoot a picture. 3. Sport Mode Sport start Notify mode Stopwatch mode Sport Step Mode Sport Clock Mode Sport Calories Mode Sport Distance Mode Sport stop Notify mode 4. Notification Mode Incoming call notify Alarming notify Message notify Sedentary notify

... 5m 7 7 7 7APP Nordic kionix 0.86 18g 50mAh 4.0

-10-45 IP67 7 95%

0.5 10

-

Activities Record:

Record daily activities, you could check daily activities including steps, distance and calorie consumption in the app;

Sleep Monitoring:

Device could automatically recognize your state and monitoring the whole sleep progress with analyzing the deep sleep and light sleep hours;

Notification Alerts:

Alarm alert, call alert, sedentary alert, etc. by silent vibration;

Anti-Lost:

When the smart phone is beyond the Bluetooth range (5m), the device vibrates to remind. Remote Camera Control:

Operation on the screen could control remote photograph shooting. Device Data Storage:

The activity data will be cleared every 0:00am as a cycle, but the device itself could restore 7 days data, after 7 days, the data will be cleared. We suggest user to sync data with app at least one time within 7 days during use. Cant find device when pairing device?

Please make sure the smart phone Bluetooth is ON and smart phone OS Android 4.4 & above and iOS 7.1 & above. Please make sure the device is near the smart phone when pairing (normal 0.5m) and among the normal Bluetooth communication distance range

(within 10m). Please make sure the device is not under low battery. If there is still problem after full charge, please contact us. Cant connect the device with app?

Some smart phone Bluetooth service will be abnormal when reboot. Please reboot the Bluetooth or reboot smart phone for pairing device. How to Restore Factory Defaults Make sure the device is connected with app, go in the app, enter Mine-SystemSetting and choose Reboot Device. How to update the device Make sure the device is connected with app, go in the app Device-

Device update, please wait some minutes before update done. CPU: Nordic Sensor: kionix Screen Size: 0.86OLED screen Host Weight: 18g Battery Type: Polymer Rechargeable Li Battery Battery Capacity: 50mAh Data Sync: Bluetooth 4.0 Working Temperature: -10C--45C Dustproof and Waterproof level: IP67 Standby: more than 7 days This product is applied with professional Bluetooth RF signal and self developed algorithm, the accuracy of step pedometer could be up to 95%. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Smart Band PS:This product has no HR function but also apply to this version of App 1. Download VeryFit for heart rate app The smart band need to pair with the smart phone through app. Before downloading, please refer to working condition for mobile. Way to download 1: Searching the QR code, scan and download app. Please use the QR code Scan tool to scan the following QR code and open the link and download app. In case there is any problem to open the link, please try to copy the link and open it by browser. Way to download 2: Search in the phone market and download. Please search and download the VeryFit for heart rate from App Store or Google play store. Once the device connected to the app successfully, it will record and analyze your activities and sleep automatically, pleasetouch and sliding on the screen of the device to switch into different display modes as following:

1. Normal Mode Time Mode Step mode 3. Pair the device Open pair device in the app, please make sure the Bluetooth is ON when pair the device. When searching and pairing device, please long press on the screen of the device and activate the device (light on). App will search the device automatically, choose the device name and connect the device to the app. Distance mode Calories Mode Anti-lost notify Goal complete notify Activity Time Mode Select the device in the smart phone searching list Alarm mode Find Phone Note: alarm mode and find phone will only be displayed on the screen after switch ON in the APP. Low-power notify Charge full notify Charging notify Notification Mode instruction 1.Under incoming call, message notify mode, the screen will still display the last time text and sliding, when there is a new notification coming in. 2. If there is a call or message come, the device will force into call/message alert mode no matter under whatever other mode, after quit, it returns to previous mode.