PA923 PORTABLE 160-WATT BLUETOOTH PARTY SPEAKER 15 UserMan r2 Users Manual

TM PORTABLE 160-WATT BLUETOOTH R PARTY SPEAKER Model: BWD19AAS11 PRODUCT GUIDE Ver.01 Rev.01/22/18 1 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all Instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the pointwhere they exit from the apparatus. 11. Only use attachment/accessories specified by the manufacturer. 12. Use only the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Power Sources - This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit. 16. Water and Moisture - This product should be kept away from direct contact with liquids. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. 17. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type Batteries (a battery pack or an installed battery) shall not be exposes to excessive heat such as sunshine, fire, etc. 18. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. 19. This symbol means the equipment is a Class II or double-insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. 20. Do not install this equipment in a confined or "boxed-in" space such as a bookcase or similar unit, and maintain good ventilation conditions. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, tablecloths, curtains, etc. 21. This apparatus is for professional use only. 22. When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable tie). Be careful not to damage the power cord. Before using it again, make sure the power cord has not been damaged. If the power cord has been damaged at all, bring the unit and cord to a qualified service technician for repair or replacement as specified by the manufacturer. 23. WARNING: Please refer to any important information (e.g., electrical, safety, etc.) printed on the exterior side enclosure before installing or operating the product. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.The use of apparatus in moderate climates;No naked flame sources, such as lighted candles, should be placed on the apparatus; Minimum distances 5cm around the apparatus for sufficient ventilation;To preserve our environment, dispose of used batteries according to your local laws or regulations. SERVICE INSTRUCTIONS

. Disconnect power cord before servicing. Replace critical components only with factory parts or recommended equivalents

. For AC line powered units Before returning repaired unit to user, use an ohmmeter to measure from both AC plug blades to all exposed metal parts. The resistance should be more than 2,000,000 ohms. SAFETY NOTICES CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE ANY COVER. NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY. DANGEROUS VOLTAGE: triangle is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. SA 1965 2 3 INSTRUCCIONES IMPORTANTES DE SEGURIDAD 1. Lea estas instrucciones. 2. Conserve estas instrucciones. 3. Preste atencin a las advertencias. 4. Siga todas las instrucciones. 5. No use este equipo cerca de agua. 6. Lmpielo slo con un pao seco. 7. No bloquee las aberturas de ventilacin. Instale el equipo de acuerdo con las instrucciones del fabricante. 8. No instale el equipo cerca de fuentes de calor tales como radiadores, aberturas de entrada de calefaccin, calefactores u otros aparatos (incluidos amplificadores) que generen calor. 9. No anule la funcin de seguridad del enchufe tipo polarizado o con conexin a tierra. Un enchufe polarizado tiene dos patillas, una ms ancha que la otra. Un enchufe de tipo de conexin a tierra tiene dos patillas y una clavija de puesta a tierra. La patilla ancha o la tercera clavija son para su seguridad. Si el enchufe provisto no entra en su tomacorriente, consulte a un electricista y solictele el reemplazo del tomacorriente obsolete. 10. Proteja el cable de alimentacin de modo que no lo pisen ni quede estrangulado, particularmente en los enchufes, tomacorrientes y el punto donde sale del equipo. 11. Use slo agregados y accesorios especificados por el fabricante. debe conectarse a un tomacorriente del suministro elctrico con una conexin a tierra de proteccin. 12. Use slo el carrito, soporte, trpode, mnsula o mesa especificados por el fabricante o vendidos con el equipo. Si usa un carrito, tenga cuidado al mover la combinacin de carrito/equipo para evitar que se vuelque y produzca lesiones. 13. Desenchufe este equipo durante las tormentas elctricas o cuando no lo use por perodos prolongados. 14. Solicite todo servicio a personal de servicio calificado. Se requiere servicio cuando el equipo se da de cualquier manera, por ejemplo si se daaron el cable o el enchufe de alimentacin, si se derram lquido o cayeron objetos dentro del equipo, si el mismo estuvo expuesto a la lluvia o la humedad, si no funciona normalmente o se dej caer. 4 15. Suministro elctrico Conecte este producto solamente a un suministro elctrico del tipo que se describe en estas instrucciones de operacin o segn se indique en la unidad. 16. Agua y humedad - Este producto se debe mantener fuera del contacto directo con los lquidos. El aparato no debe ser expuesto al goteo o a la salpicadura y ningun objeto lleno de lquidos, como serin los floreros, debe ser colocados cerca del aparato. 17. PRECAUCIN Peligro de la explosin si la batera se substituye incorrectamente. Substituir solamente por el mismo o el tipo equivalente. Las bateras (un bloque de bateras o una batera instalada) no se deben exponer a calor excesivo, tal como la luz solar, el fuego, etc. 18. Cuando se usa el enchufe del suministro elctrico o el acoplador de un artefacto como dispositivo de desconexin, el mismo debe permanecer listo a operar. 19. Este smbolo significa que el equipo es un artefacto elctrico Clase II o de doble aislamiento. Est diseado de manera tal que no requiere una conexin de seguridad a la tierra elctrica. 20. No instale este equipo en un espacio confinado o "dentro de una caja" tal como una biblioteca o una unidad similar, y mantenga buenas condiciones de iluminacin. No debe impedirse la ventilacin cubriendo las aberturas correspondientes con elementos tales como peridicos, manteles, cortinas, etc. 21. Este aparato es para uso profesional nicamente. 22. Cuando traslade o no use el artefacto, sujete el cable de alimentacin (por ejemplo, envulvalo con un precinto). Tenga cuidado de no daar el cable de alimentacin. Antes de usarlo nuevamente, asegrese de que el cable de alimentacin no est daado. Si dicho cable presenta algn dao, lleve la unidad y el cable a un tcnico de servicio calificado para reparacin o reemplazo segn lo especifique el fabricante. 23. ADVERTENCIA: Antes de instalar u operar el producto, consulte toda la informacin importante (como la relativa a electricidad, seguridad, etc.) impresa en la envuelta inferior exterior o el panel trasero. ATTENTION : Pour rduire le risque du feu et du choc lectrique, ne pas exposer cet appareil aux pluies ou l'humidit. L'usage de cet appareil sous un climat tempr, dfense de source des flammes non protge, parexemple, des bougies claires doivent tre places sur cet appareil, 5cm de diatance au minimum autour de cet appareil pour la ventilation suffissante;

pour protger notre environnement, la disposition de batteries uses conformment la loi locale ou aux rglements. 5 LAS INSTRUCCIONES DE SERVICIO

. Desconecte el cable elctrico antes de empezar el servicio. Substituya los componentes crticos solamente por las piezas de la fbrica o las piezas equivalentes recomendadas. Para las unidades accionadas por CA - Antes de devolver la unidad reparada al utilizador, utilice un ohmmetro para medir entre las dos lminas del enchufe de CA y todas las partes expuestas. La resistencia tiene que ser ms de 2,000,000 ohms. SEALES DE ADVERTENCIA PRECAUCIN: PARA REDUCIR EL RIESGO DE DESCARGA ELCTRICA NO QUITE NINGUN TAPADERO. DENTRO DE LA UNIDAD NO HAY COMPONENTES TILES PARA EL UTILIZADOR. PARA EL SERVICIO SE DEBE DIRIGIRSE SOLAMENTE AL PERSONAL DE SERVICIO CUALIFICADO. VOLTAJE PELIGROSO NO AISLADO: La sea de relmpago con la punta de la flecha dentro del tringulo equiltero est puesto para alertar al utilizador de la presencia del

"voltaje peligroso no aislado" dentro del recinto de producto que puede tener la magnitud suficiente de correr un riesgo de descarga elctrica. SA 1965 Speaker Overview 5 4 3 2 1 MASTER VOLUME 6 7 8 9 10 11 Package Contents Main unit x 1 Power cable x 1 Product Guide x 1 12 13 14 15 16 1. Power ON/OFF 2. Bluetooth 3. Source 4. Bass boost 5. TWS 6. Party light 7. Previous(hold to seek FM station) 8. Play/Pause 9. Next(hold to seek FM station) 10. Light mode 11. Master volume control 12. AC input port 13. USB charging output 14. Microphone/Guitar volume control 15. Microphone/Guitar input 16. AUX input Product Guide 6 7 8 Charging Bluetooth pairing T TWS stereo R Wireless Stereo Pairing AUX Insert the included power cable to charge the unit. The charging icon will be on in the display when charging. Notes: The unit can be used with the power cable while it simultaneously charges the battery. When four charging indicators light up, indicates that the battery is fully charged. When the red indictor flashes, it indicates that the battery is low and needs to be recharged. To save power, when the speaker is not in use, always turn off the unit the. Bluetooth Bluetooth Devices Blackweb Party SPK MASTER VOLUME 1. Hold to power on the product. 2. The Bluetooth icon in the display will start blinking rapidly. 3. Active the Bluetooth function on your device and search Bluetooth devices, and select Blackweb Party SPK to start connecting. 4. Once paired, the Bluetooth icon in the display will turn on steadily, and you will hear Bluetooth Connected. 5. Play music on your device paired and connected with the speaker. During music play:

. Turn the Master volume knob to adjust volume. Press to pause or resume music play. Press to skip to the previous/next song. Press Bass to get rich bass. BASS BOOST will light up in the display. Notes: This speaker supports automatic connection with a previously paired device after power-off and power-on again. To pair with a new Bluetooth device or connect a previously paired device, first hold to power on the product, and then repeat the above step 3. Stereo 10m Use a 3.5mm cable (not included) to connect the speaker to another audio source. Play and control music on your audio device, and use the volume knob on the speaker to adjust volume if necessary. Notes: In AUX mode, cant be controlled. AUX 1. Short press of both speakers to enter True Wireless Stereo Pairing mode, the LINK icon on the display will start blinking rapidly. 2. When the two speakers connected, LINK icon will turn on steadily. 3. Long press to disconnect True Wireless Stereo mode. 4. Follow the instruction of your device to pair the speakers and play music. With Ture Wireless Stereo technology, you can connect your speaker to another one and explore the best sound effects with left and right sound channels separated on different Bluetooth speaker. 1. Press SOURCE to the FM mode. 2. A. Press repeatedly to tune to a station step by step. B. Hold to tune to a station automatically. 3. Turn the Master volume knob to adjust volume. To program FM radio station 1. Hold 2 seconds to search and program available stations. 2. LED display will show the program numbers such as: P_1 or P_2 P_10(Max). 3. Tune to a station with , and then press to assign above program number to it. When successfully, the LED display will show SAVE. 4. Short press to select the corresponding station in your program list. Notes: The speaker will remember the last station it was on and start at that station when powered off and on again. 1. Connect your Microphone(not included) or Guitar(not included) to the MIC/Guitar socket. 2. Play Guitar through the speaker. 3. Sing along with the Microphone when music played on Bluetooth/Aux/FM mode. 4. Turn the MIC/GUITAR knob to adjust the Microphone or Guitar volume. Connect your devices charging cable through the 5V 1A charging socket to charge it. USB charging only functions when the units power if turned on. Notes: To charge smartphones and tablets faster, put the devices screen to sleep. 1. Hold to turn on / turn off the light mode. 2. Short press repeatedly to select 5 available display modes. 3. Short press PARTY LIGHT to turn on / off the light effect. Technical Specifications Output power (RMS): 80W Battery type: Lead-acid rechargeable Bluetooth transmitter frequency range: 2.402 2.480GHz 9 10 11 12 13 14 15 16 USER MANUAL INSERTS FOR FCC ID 1. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 2. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 3. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. 4. RF Exposure Statement To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. Product for Wal-Mart Stores, Inc. Bentonville, AR72716,Hotline 1-800-925-6278 17