CF-WU925A 11AC USB Wireless Adapter User manual

 

Quick Installation Guide Realtek Driver Installation M0304322 Version2.0 1 Hardware Installation Here are two methods to install the usb adapter 1. Please insert the usb adapter directly into the computer's USB port. 2. Connect the USB port of the computer through the USB extension cable base. (USB extension base is sold separately) Note: When using the desktop, it is recommended to use the USB extension cable base to connect the rear interface of the computer chassis.(Most of the desktop computer's front USB interface is underpowered or unavailable), extended to the desktopUse, the effect is better!

2 Driver Installation 1.Put the CD driver into the computer drive. 2.Open the driver folder and double click the installation file Setup.exe.Click "Next"to finish the installation. NoteIf the installation file is a compressed package, you need to extract it to install it. REALTEK 11n USB Wireless LAN Software REALTEK 11n USB Wireless LAN Software The InstallShield Wizard will install REALTEK 11n USB Wirekess LAN Software on your computer. To continue,click Next. Back Next Cancel After finishing the installation 3. the taskbar, [REALTEKK Client Management Software ] appears, indicating the installation succeed.

, in the lower right corner of

. 3 Network Connection Settings 1. Double-click the wireless network card management icon to open the network card client management software. 2.Click on the upper menu "Available Network", select the wireless network SSID you want to connect to, and then click"Add to Profile" as shown below:

REALTEK 11n USB Wireless LAN Utility RefreshRModeM AboutA MyComputer Realtek RTL General Profile Available Network Status Statistics Available Network(S) SSID Channel Encryption Network Authentication Signal Comfast CMCC 4 6 AES AES WPA PSK WPA PSK 100%

42%

Refresh Add to Profile 3.Enter the network key, Confirm the network key, click as shown below:

OK Wireless Network Properties Profile Name COMFAST Wireless network security This network requires a key for the following Network Authentication WPA2-PSK Data encryption AES Network key

************

Confirm network key

************

OK Cancel 4.After the connection is successful, the signal strength and link quality are displayed, as shown below:

REALTEK 11n USB Wireless LAN Utility RefreshRModeM AboutA MyComputer Realtek RTL General Profile Available Network Status Statistics StatusAssociated SpeedTx:150Mbps Rx:300Mbps TypeInfrastructure EncryptionAES SSIDCOMFAST Signal Strength Link Quality ReNewIP 98%

100%

Note: If you do not get the IP address or receive the data packet, it may be the password input error, please re-enter the correct password to regain the IP. For the network with fixed IP address, you need to
Set the IP address. 4 WiFi Transmitter Settings

(Note: Win10 system does not support this feature) 1.Click on the management software menu [Mode] to select

[Access Point], as shown below:

Status Statistics REALTEK 11n USB Wireless LAN Utility RefreshR ModeM AboutA MyComputer Realtek RTL Available Network Base station General Profile Access Point Status Virtual WiFi Speed Type Encryption Signal Strength Link Quality ReNewIP 2.After switching to access point mode, the SSID displays the name of the computer, as shown below:

REALTEK 11n USB Wireless LAN Utility RefreshR ModeM AboutA MyComputer Realtek RTL General Advanced Statistics ICS SSID BSSID00:0D:B1:A2:0B:D1 Association Table AID MAC Address Period of use Configuration Note: The default of the computer name is WiFiSSID. The default is no password. If you need to use the password and change the SSID, please see the following operations. 3.Click on the image above to open the Wireless Network Properties Settings dialog to set the network name (SSID), channel, encryption algorithm and password. Click Configuration OK Wireless Network Properties Network name (SSID) COMFAST_AP Channel 62437MHz Wireless network security This network requires a key for the following Network Authentication WPA2-PSK Data encryption AES Network key

************

Confirm network key

************

OK Cancel Application 4.Click "ICS" to select the network connected to your computer, click , as shown below:

(Win7 system interface will be a bit different here, the setting method is the same) REALTEK 11n USB Wireless LAN Utility RefreshR ModeM AboutA MyComputer Realtek RTL General Advanced Statistics ICS Set up Internet connection sharingICS ConnName WiFi connection 4 11b/g Wireless LAN Mini PCI Device name Express Adapter III Application 5.Set it according to your network type and select the network you are using. If the network is bound to IP address and MAC address or is restricted to use by a single computer, it can not share the network. If the setting is not successful, please share the network manually

(see Setting up a network share manually). Note:

A. Connect to the computer through Modem (cat), use the computer broadband connection to dial, here must choose

"broadband connection";

B. Connect the line from the router or switch to the Internet. Here, select the name of the interface card corresponding to the local connection (usually the default);

C. If the wireless network card that comes with the notebook is connected to the wireless network, select the name of the interface card of the wireless network card;

D. If you use the 4G network card to access the Internet, select the interface card name of the 4G network card.

Thank you for purchasing

















products. To protect your rights and interessts in after-sales service

please read the following maintenance regulations. g Copyright Information

+86 755 83790059 en.comfast.com.cn FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:

The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.