324131296121X Wireless control board TempConfidential user manual Rev4

 

Machine &

Product Documentation Lighting

(Product family) Wireless control board Changing Content List

(Document type) PRODUCT SPECIFICATION Updated Date Change Request No. Remarks 2018/06/12 Initial version The Wireless control board is a general purpose Zigbee certified building block for SMART TLED lighting applications e.g. SMART TLED and luminaires. It does not work stand-alone but is meant to be connected by socket on a application specific motherboard that contains the proper interfacing for stand-alone usage (i.e. connectors, supply voltage, ...) Technical Project Leader Quality Project Leader Product Manager Signature

(12nc) 324131296121 190-1 8 p L A4 Product Sheet 190 BMS BLLL TND-410-TP-SHA Release Nr 2.0 Philips Lighting

(Product family) Wireless control board

(Document type) PRODUCT SPECIFICATION Machine &

Product Documentation Lighting 1. Module layout and drawings Name Width (mm) Length (mm) Height (mm) Drawings:

Value 20.8 39.5 12 Tolerance Remarks 0.2 0.2 1 Technical Project Leader Quality Project Leader Product Manager Signature

(12nc) 324131296121 190-2 8 p L A4 Product Sheet 190 BMS BLLL TND-410-TP-SHA Release Nr 2.0 Philips Lighting Machine &

Product Documentation Lighting I/O definition:

(Product family) Wireless control board

(Document type) PRODUCT SPECIFICATION Function PWM output DC input Ground ON/OFF Sensor_Tx PWM 5V GND GND Sensor_Tx Sensor_nReset Sensor_nReset V_LED V_LED input Sensor_Boot Sensor_Boot I_LED output I_LED Sensor_Tx Sensor_Tx Pad Number 1 2 3 4 5 6 7 8 9 10 2. ELECTRICL SPECIFICATION Name Vcc voltage (V) Current (normal, mA) Value 5V Tolerance 5%

Remarks 40 Technical Project Leader Quality Project Leader Product Manager Signature

(12nc) 324131296121 190-3 8 p L A4 Product Sheet 190 BMS BLLL TND-410-TP-SHA Release Nr 2.0 Philips Lighting

(Product family) Wireless control board

(Document type) PRODUCT SPECIFICATION Machine &

Product Documentation Lighting 3. RF PERFORMANCE SPECIFICATION Item Conditions Spec Min Typical Max Frequency tolerances

(ppm) Output power (dBm) Spurious emissions*

(dBm) EVM (%rms) Receiver Sensitivity

(dBm) TRP Continuous single tone Measured at antenna feed point 30 1000MHz 1 12.75GHz 1.8 1.9GHz 5.15 5.3GHz PER < 1%

when connected to motherboard (i.e. SMART TLED)

+/-40 4

-36

-30

-47

-47

<10

-99

-2dBm 4. Approbation PMN(product marketing name): Wireless control board Technical Project Leader Quality Project Leader Product Manager Signature

(12nc) 324131296121 190-4 8 p L A4 Product Sheet 190 BMS BLLL TND-410-TP-SHA Release Nr 2.0 Philips Lighting

(Document type)

(Product family) PRODUCT SPECIFICATION Wireless control board Machine &

Product Documentation Lighting FCC Labelling Requirements When integrating HUE Engine V1.0 into a product it must be ensured that the FCC labelling requirements are met. This includes a clearly visible label on the outside of the finished product specifying the FCC identifier (FCCID:2AGBW324131296121X). This exterior label can use wording such as Contains Transmitter Module FCC ID:2AGBW324131296121X although any similar wording that expresses the same meaning may be used. Note: Changes or modifications made to this device that are not expressly approved by Philips Lighting North America Corporation(Philips) may void the user's authority to operate the device. The advance interface module complies with FCC radiation exposure limits set forth for an uncontrolled environment. The module and associated antenna must be installed to provide a separation distance of at least 20cm from all persons and must not transmit simultaneously with any other antenna or transmitter. FCC Approvals FCC statement:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC notice:

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful Technical Project Leader Quality Project Leader Product Manager Signature

(12nc) 324131296121 190-5 8 p L A4 Product Sheet 190 BMS BLLL TND-410-TP-SHA Release Nr 2.0 Philips Lighting

(Document type)

(Product family) PRODUCT SPECIFICATION Wireless control board Machine &

Product Documentation Lighting interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the device and receiver Connect the device into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/television technician for help . IC (Industry Canada) Approvals This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication This module complies with FCC and Industry Canada RF radiation exposure limits set forth for general population. To maintain compliance, this module must not be co-located or operating in conjunction with any other antenna or transmitter Immediately following the above notice, the manufacturer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi) and required impedance for each. Technical Project Leader Quality Project Leader Product Manager Signature

(12nc) 324131296121 190-6 8 p L A4 Product Sheet 190 BMS BLLL TND-410-TP-SHA Release Nr 2.0 Philips Lighting

(Document type)

(Product family) PRODUCT SPECIFICATION Wireless control board Machine &

Product Documentation Lighting The labelling requirements for Industry Canada are similar to those of the FCC. Again a clearly visibly label must be placed on the outside of the finished product stating something like Contains Transmitter Module, IC ID: 20812-6121X, although any similar wording that expresses the same meaning may be used. En vertu de la rglementation dIndustrie Canada, cet metteur radio risquera uniquement laide dune antenne de type et de gain maximum (ou moins) pour lmetteur a approuv par Industrie Canada. Pour rduire les interfrences radio potentielles dautres utilisateurs, le type dantenne et son gain doivent tre choisies que la puissance isotrope rayonne quivalente (p.i.r.e.) nest pas plus que celle autorise pour une communication russie Ce module est conforme la FCC et Industrie Canada RF limites dexposition aux rayonnements dfinies pour lensemble de la population. Pour maintenir la conformit, ce module ne doit pas tre co-implant ou fonctionner en conjonction avec toute autre antenne ou metteur la suite de lavis ci-dessus, le fabricant doit fournir une liste de tous les types dantenne approuvs pour une utilisation avec lmetteur, indiquant au maximum gain dantenne (en dBi) et impdance requise pour chacun. Les exigences dtiquetage pour Industrie Canada sont semblables celles de la FCC. Encore une fois un clairement visiblement tiquette doit tre place lextrieur du produit fini indiquant quelque chose comme "Module metteur de Contains, IC ID:

20812-6121X", bien que tout mme libell qui exprime que le mme sens peuvent tre utilis. IC notice:

This Class B complies with Canadian ICES-005.---

Cet appareil numrique de la classe B est conforme la norme NMB 005 du Canada Technical Project Leader Quality Project Leader Product Manager Signature

(12nc) 324131296121 190-7 8 p L A4 Product Sheet 190 BMS BLLL TND-410-TP-SHA Release Nr 2.0 Philips Lighting

(Product family) Wireless control board Machine &

Product Documentation Lighting

(Document type) PRODUCT SPECIFICATION Technical Project Leader Quality Project Leader Product Manager Signature

(12nc) 324131296121 190-8 8 p L A4 Product Sheet 190 BMS BLLL TND-410-TP-SHA Release Nr 2.0 Philips Lighting