| submitted | available | document details (if available) | source link |
|---|---|---|---|
| various | Users Manual | Users Manual | 1.69 MiB |
Title:
SX-SDMAC-2832S/SX-SDMAC-2832S+
Drawing Type :
Users Manual Drawing No.:
JW204430XX Date :
July 13, 2017 silex technology, Inc.
(1/27) CONFIDENTIAL Revision history Rev. Description Date Prepared by Checked by Approved by XX The 1st draft version. Jul.13,17 K.Yoshikawa Y.Kuroda Y.Shibuya Drawing No.JW204430XX silex technology, Inc.
(2/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX Index 1. Product introduction ....................................................................................................................................................................................... 4 2. Hardware block diagram................................................................................................................................................................................ 6 3. Board specifications ....................................................................................................................................................................................... 7 3.1. 3.2. 3.3. 3.4. General specifications .....................................................................................................................................................7 Environmental conditions ................................................................................................................................................7 Electrical specifications ...................................................................................................................................................8 Current consumption specifications .......................................................................................................................... 10 3.5. Wireless LAN general specifications ......................................................................................................................... 11 3.6. Wireless LAN transmitter specifications ................................................................................................................... 13 3.7. Wireless LAN Receiver specifications ....................................................................................................................... 14 3.8. 3.9. Bluetooth general specifications ................................................................................................................................ 16 Bluetooth Transmitter specifications ......................................................................................................................... 16 3.10. Bluetooth Receiver specifications .............................................................................................................................. 16 4. Signal pin specifications .............................................................................................................................................................................. 17 4.1. 4.2. Pin locations.................................................................................................................................................................... 17 Signal specifications...................................................................................................................................................... 18 5. Mechanical Specifications .......................................................................................................................................................................... 20 6. Indication specifications .............................................................................................................................................................................. 21 7. System requirements and quick start guide .......................................................................................................................................... 22 8. Notifications .................................................................................................................................................................................................... 24 silex technology, Inc.
(3/27) DateJuly 13, 2017 CONFIDENTIAL This document describes about SX-SDMAC-2832S and SX-SDMAC-2832S+. Hereinafter called SX-SDMAC-2832. Drawing No.JW204430XX 1. Product introduction The SX-SDMAC-2832S is a 2.4 GHz / 5GHz dual band IEEE802.11 a/b/g/n/ac Wave2 WLAN + Bluetooth 4.2 BR/EDR/LE SDIO3.0 combo radio module based on Qualcomm QCA9377-3 chipset. The SX-SDMAC-2832 highly integrates MAC, Base band, RF, RF front end and peripheral circuitry like power unit, reference clock, etc. The SX-SDMAC-2832 has a MHF-I connector as connection interface for an add-on antenna. SX-SDMAC-2832S/SX-SDMAC-2832S+
silex technology, Inc.
(4/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX Features IEEE802.11a/b/g/n/ac Wave2 compliant (2.4 GHz, 5 GHz) 1 spatial data stream system (1T1R) 5 GHz : Support 20/40/80 MHz bandwidth mode (PHY Data rate 433 Mbps) 2.4 GHz : Support 20/40 MHz bandwidth mode (PHY Data rate 150 Mbps,Extra PHY Data rate 200Mbps)
*20/40MHz Co-existence is not supported. PHY Data Rate 802.11b/g 1-54 Mbps 802.11a 6-54 Mbps 802.11n MCS0-7 High Speed mode (HT mode) 802.11ac MCS0-9 Very High Speed mode (VHT mode) Bluetooth 4.2 BR/EDR/LE(Class2). Backward-compatible to Bluetooth 1.x, 2.x, 3.0, 4.0 (Support LE Data Length Extension) SDIO3.0 as the Wireless LAN host interface UART as the Bluetooth host interface
+3.3V main power supply and selectable +1.8V/+3.3V IO power supply EU RoHS directive 2011/65/EC (Lead Free), (EU)/2015/863 compliant silex technology, Inc.
(5/27) DateJuly 13, 2017 CONFIDENTIAL 2. Hardware block diagram Drawing No.JW204430XX Acronyms PMU IPD LPF IPD DPX MHF-I Power Management Unit Integrated Passive Device type Low Pass Filter Integrated Passive Device type Diplexer MHF-I co-axial connector (I-PEX) or compatible connector NOTE1WLAN and Bluetooth dont work in the same time because of TDMA (Time Domain Multiple Access) protocol. NOTE2All power input (+3.3V and +1.1V) used for RF are regulated/compensated in the module. silex technology, Inc.
(6/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX 3. Board specifications 3.1. General specifications Items Specifications Units Remarks Connection with the host board 44-pin Land Grid Array (Direct solder) Antenna port Host interface MHF1 connector x1 SDIO v3.0 UART RF interface IEEE802.11a/b/g/n/ac Bluetooth 4.2 BR/EDR/LE pc Dimensions W x H x D 17.0 x 18.0 x 2.6 mm For Wireless LAN For Bluetooth, up to 4Mbps IEEE802.11-2012 IEEE802.11ac-2013 3.2. Environmental conditions Items Units Remarks Min. Typ. Max. Specifications Recommended operating temperature
-20 Recommended operating humidity Recommended strage temperature Recommended strage humidity 15
-20 10
+85 Ambient temperature 93
%RH No condensing
+95 Ambient temperature 95
%RH No condensing silex technology, Inc.
(7/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX 3.3. Electrical specifications Absolute maximum rating Items Units Remarks Specifications Main power supply
(VDD) IO power supply voltage
(VDD_GPIO_1, VDD_GPIO_2) SDIO power supply voltage
(VDD_SDIO) Min. Typ. Max.
-0.30
-0.30
-0.30
+3.65
+4.00
+4.00 V V V Recommended operating conditions Main power supply/Bluetooth power supply Items Units Remarks Min. Typ. Max. Specifications Main power supply
(VDD)
+3.135
+3.30
+3.465 V IO power supply/SDIO power supply with +3.3V operation Items Units Remarks Specifications IO power supply voltage
(VDD_GPIO_1, VDD_GPIO_2) SDIO power supply voltage
(VDD_SDIO) Min. Typ. Max.
+3.14
+3.30
+3.46
+3.14
+3.30
+3.46 IO power supply/SDIO power supply with +1.8V operation Items IO power supply voltage
(VDD_GPIO_1, VDD_GPIO_2) SDIO power supply voltage
(VDD_SDIO) Specifications Min. Typ. Max.
+1.71
+1.80
+1.89
+1.71
+1.80
+1.89 V V Units V V Remarks All voltage source for the analog RF power supply is internally regulated in the module, and RF performance described in this document is not affected by any variation for external power source. silex technology, Inc.
(8/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX Digital logic signal level 1) VIO (VDD_GPIO_1, VDD_GPIO_2, VDD_SDIO) = +3.3V operation Specifications Items Parameters Output/Input current Min. Typ. Max. Units Remarks VIH VIL Input High voltage Input Low voltage
-0.3 0.7 x VIO
+3.3 VIO + 0.3 V V V V 0.3 x VIO 0.1 x VIO VOH Output High voltage IOH = 3mA VIO - 0.4 VOL Output Low voltage IOL = -11mA 2) VIO (VDD_GPIO_1, VDD_GPIO_2, VDD_SDIO) = +1.8V operation Specifications Items Parameters Output/Input current Min. Typ. Max. Units Remarks VIH VIL Input High voltage Input Low voltage
-0.3 0.7 x VIO
+1.8 VIO + 0.2 V V V V 0.3 x VIO VIO 0.1 x VIO VOH Output High voltage IOH = 3mA VIO - 0.4 VOL Output Low voltage IOL = -11mA silex technology, Inc.
(9/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX Current consumption specifications 3.4. VDD (WLAN Operation) Items Units Remarks Mode Standards Typ. Max. Specifications Current consumption Tx 11b 280 430 mA 2.4GHz 11g 280 430 mA 11ng HT20 280 430 mA 11ng HT40 280 430 mA Rx All mode 70 90 mA Current consumption Tx 11a 480 630 mA 5GHz 11na HT20 480 630 mA 11na HT40 480 630 mA 11ac VHT80 480 630 mA Rx All mode 90 110 mA silex technology, Inc.
(10/27) DateJuly 13, 2017 CONFIDENTIAL 3.5. Wireless LAN general specifications Items Specifications Units Remarks Drawing No.JW204430XX Chipset QCA9377-3 (Qualcomm Atheros) Operating frequencies Band Modes Min Max 2.4GHz 11b 2412 2462 MHz 11g/n/ac 20MHz 2412 2462 MHz 11g/n/ac 40MHz 2422 2452 MHz 5GHz 11a/n/ac 20MHz 5180 5825 MHz 11n/ac 40MHz 5190 5795 MHz 11ac 80MHz 5210 5775 MHz Frequency steps 2.4GHz 11b/g/n 5GHz 11a/n/ac 20MHz 11n/ac 40MHz 11ac 80MHz 5 20 40 80 Data rates 11b 1,2,5.5L,5.5S,11L,11S Modulation types 11a/g 6,9,12,18,24,36,48,54 11n 11ac 11b MCS 0,1,2,3,4,5,6,7 MCS 0,1,2,3,4,5,6,7,8,9 DSSS(DBPSK,DQPSK,CCK) 11a/g/n OFDM(BPSK,QPSK,16QAM,64QAM) 11ac OFDM(BPSK,QPSK,16QAM,64QAM,256QAM) MHz MHz MHz MHz Mbps Mbps silex technology, Inc.
(11/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX Operatable channel list 2.4GHz US/CA 20MHz Ch.1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 40MHz Ch.3, 4, 5, 6, 7, 8, 9 5GHz US 20MHz Ch.36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,165 40MHz Ch.38,46,54,62,102,110,118,126,134,151,159 80MHz Ch.42,58,106,122,155 CA 20MHz Ch.36,40,44,48,52,56,60,64,100,104,108,112,116,132,136,140,145,149,153,157,161,165 40MHz Ch.38,46,54,62,102,110,134,151,159 80MHz Ch.42,58,106,155 Above region code relating channel list is programmed in the module by module manufacturer (Silex). Since programmed region code and channel list is binary data and user cannot know the structure of program, any customers cannot change usable channels. Operation theory Client mode (Station) Operation frequencies Active/Passive ad-hoc mode 2.4GHz band 11b/g/n 2412-2462MHz W52 W53 W56 W58 11a/an/ac 5180-5240MHz 11a/an/ac 5260-5320MHz 11a/an/ac 5500-5700MHz IC:5600-5650MHz disable 11a/an/ac 5745-5825MHz Active scan Active scan Passive scan Passive scan Active scan No No No No No Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. silex technology, Inc.
(12/27) DateJuly 13, 2017 CONFIDENTIAL 3.6. Wireless LAN transmitter specifications Drawing No.JW204430XX Modes Channels Target Power Units Specifications Remarks 11b 11g Ch.1-Ch.11 Ch.1-Ch.11 11n 20MHz Ch.1-Ch.11 11n 40MHz Ch.3-Ch.9
+18.0
+16.5
+16.5
+16.5 dBm dBm dBm dBm 2.4GHz (+25) Items Transmit Power 5GHz (+25) Items Transmit Power 11a Modes Channels Target Power Units Specifications Ch.36-Ch.48 Ch.52-Ch.64 Ch.100-Ch.140 Ch.149-Ch.165 11n/ac 20MHz Ch.36-Ch.48 Ch.52-Ch.64 Ch.100-Ch.140 Ch.149-Ch.165 11n/ac 40MHz Ch.38-Ch.46 11ac 80MHz Ch.54-Ch.62 Ch.102-Ch.134 Ch.151-Ch.159 Ch.42 Ch.58 Ch.106-Ch.122 Ch.155
+10.0
+10.0
+10.0
+10.0
+11.0
+11.0
+11.0
+11.0
+10.0
+10.0
+10.0
+10.0
+9.0
+9.0
+9.0
+9.5 dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm Remarks silex technology, Inc.
(13/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX 3.7. Wireless LAN Receiver specifications 2.4GHz (Operating temperature Items Specifications Modes Max. Units Remarks Receiver minimum 11b sensitivity
(FER<8%)
-80
-80
-76
-76
-82
-81
-79
-77
-74
-70
-66
-65
-82
-79
-77
-74
-70
-66
-65
-64
-59
-79
-76
-74
-71
-67
-63
-62
-61
-56
-54 dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT VHT VHT 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps 11g
(PER<10%) 11n/ac 20MHz MCS0
(PER<10%) MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 11n/ac 40MHz MCS0
(PER<10%) MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9 silex technology, Inc.
(14/27) DateJuly 13, 2017 CONFIDENTIAL 5GHz (Operating temperature Items Specifications Modes Max. Units Remarks Drawing No.JW204430XX Receiver minimum 11a sensitivity
(PER<10%) 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps 11n/ac 20MHz MCS0
(PER<10%) MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 11n/ac 40MHz MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9 MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS7 MCS8 MCS9
(PER<10%) 11ac 80MHz
(PER<10%)
-82
-81
-79
-77
-74
-70
-66
-65
-82
-79
-77
-74
-70
-66
-65
-64
-59
-79
-76
-74
-71
-67
-63
-62
-61
-56
-54
-76
-73
-71
-68
-64
-60
-59
-58
-53
-51 dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT VHT VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT HT/VHT VHT VHT silex technology, Inc.
(15/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX Bluetooth general specifications 3.8. Items Specifications Units Remarks Chipset QCA9377-3 (Qualcomm Atheros) Core specification Bluetooth 4.2 Operating Frequency range Mode BR/EDR/LE Min 2402 Max 2480 MHz Max antenna gain
+3.25dBi@2.4GHz Frequency step BR/EDR LE 1 2 MHz Ch.1-Ch.79 MHz Ch.0-Ch.39 Modulation type GFSK(1Mbps),/4 DQPSK(2Mbps),8DQPSK(3Mbps) 3.9. Bluetooth Transmitter specifications Bluetooth BR/EDR/LE (+25) Items Units Remarks Standards Min. Typ. Max. Specifications Maximum TX power BR Class 2 Ch.1-Ch.79 EDR Class 2 Ch.1-Ch.79 LE Ch.0-Ch.39 3.10. Bluetooth Receiver specifications Bluetooth BR/EDR/LE (Operating temperature)
-3.7
-6.7
-4.2
+0.5
+4.0 dBm Class 2
-2.5
+1.0 dBm Class 2
+1.5
+3.5 dBm Items Specifications Units Remarks Receiver minimum Standards Packet Types Min. Typ. Max. Sensitivity BR (BER<0.1%) GFSK (1Mbps) EDR
(BER<0.01%)
/4 DQPSK (2Mbps) 8DQPSK (3Mbps) LE (PER<30%) GFSK (1Mbps)
-90
-89
-84
-94
-70 dBm
-70 dBm
-70
-70 dBm dBm silex technology, Inc.
(16/27) DateJuly 13, 2017 CONFIDENTIAL Signal pin specifications 4. 4.1. Pin locations Drawing No.JW204430XX Pin 1 marking Top view Bottom view silex technology, Inc.
(17/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX 4.2. Signal specifications Num Signal name Type I/O Domain Descriptions 1 2 3 4 5 6 7 8 9 GND NC GND GND Ground NC NC NC pin WLAN_PWD_L PD VDD_GPIO_1 WLAN reset. (0=Disable, 1=Enable) Internal Pull-down. VDD VDD VDD VDD VDD_GPIO_1 VDD_GPIO_2 P P P P P P P P P P P P
+3.135+3.465V
+3.135+3.465V
+3.135+3.465V
+3.135+3.465V
+1.71 +3.46V
+1.71 +3.46V 10 11 GND GND GND GND Ground GND GND Ground 12 SD_D3 B VDD_SDIO 13 SD_D2 B VDD_SDIO 14 SD_D1 VDD_SDIO SDIO Data[3] for WLAN. Since this pin is used for Bootstrap option, you must not drive this pin until releasing the reset signal. Internal Pull-up. SDIO Data[2] for WLAN. Since this pin is used for Bootstrap option, you must not drive this pin until releasing the reset signal. Interal Pull-up SDIO Data[1] for WLAN. Since this pin is used for Bootstrap option, you must not drive this pin until releasing the reset signal. Interal Pull-up B B B 15 16 17 18 19 SD_D0 SD_CMD VDD_SDIO SDIO Data[0] for WLAN. VDD_SDIO SDIO command for WLAN. GND GND GND Ground SD_CLK DI VDD_SDIO SDIO Clock for WLAN. GND GND GND Ground 20 RESERVED DO VDD_SDIO Un-used signal. Keep Open. Since this pin is used for Bootstrap option, you must not drive this pin until releasing the reset signal. Internal Pull-up. 21 22 23 VDD_SDIO P P
+1.71 +3.46V GND GND GND GND Ground GND GND Ground UART RXD for BT. Since this pin is used for Bootstrap option, you must not drive this pin 24 BT_UART_RXD DI VDD_GPIO_1 until releasing the reset signal.Keep Open if BT is not used. Interal Pull-up. 25 BT_UART_CTS DI VDD_GPIO_1 UART CTS for BT. Since this pin is used for Bootstrap option, you must not drive this pin until releasing the reset signal. Keep Open if BT is not used. Interal Pull-up. silex technology, Inc.
(18/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX Num Signal name Type I/O Domain Descriptions 26 BT_UART_TXD DO VDD_GPIO_1 UART TXD for BT. Since this pin is used for Bootstrap option, you must not drive this pin until releasing the reset signal. Keep Open if BT is not used. Interal Pull-up. 27 28 29 BT_UART_RTS DO VDD_GPIO_1 UART RTS for BT. Keep Open if BT is not used. NC RESERVED NC DI NC NC pin VDD Un-used signal. Keep Open. 30 RESERVED OD Open drain and need external pull-up to IO power rail of the connected external system if the debug Un-used signal (Debug port).. Open drain output. Recommended to connect to a test pad function is used. Keep Open if the debug function is not used. 31 32 33 34 GND VDD GND GND GND GND Ground P P
+3.135+3.465V GND GND Ground GND GND Ground 35 BT_WKUP_HOST OD Open drain power rail of the host system. *No testing function. Need to verify with your host board. If BT wake-up HOST. Active High. Keep Open if BT is not used. Need external pull-up to IO 36 WOW OD Open drain you need this function please contact silex support. Wake on wireless signal. Active High. Open drain output. Need external pull-up to IO power rail of the host system. 37 RESERVED PD VDD Un-used signal. Keep Open. Internal Pull-down 38 BT_I2S_SCK PD VDD_GPIO_1 BT PCM BCK. Bootstrap option, you must not drive this pin until releasing the reset signal. Keep Open if Bluetooth Audio is not used. Internal Pull-down.
*No testing function. Need to verify with your I2S device or CODEC. If you need this function please contact silex support. BT PCM SYNC. Keep Open if Bluetooth Audio is not used. Internal pull-down. 39 BT_I2S_WS B VDD_GPIO_1
*No testing function. Need to verify with your I2S device or CODEC. If you need this function please contact silex support. BT PCM IN. Keep Open if Bluetooth Audio is not used. 40 BT_I2S_SDI DI VDD_GPIO_1
*No testing function. Need to verify with your I2S device or CODEC. If you need this function please contact silex support. BT PCM OUT. Keep Open if Bluetooth Audio is not used. 41 BT_I2S_SDO DO VDD_GPIO_1
*No testing function. Need to verify with your I2S device or CODEC. If you need this function GND GND GND Ground please contact silex support. BT_PWD_L PD VDD_GPIO_1 BT HW reset. (0=Disable, 1=Enable) Internal Pull-down. GND GND GND Ground 42 43 44 Num Signal name Type I/O Domain Descriptions EXPGND Exposed Ground GND GND Exposed Ground 72 pads silex technology, Inc.
(19/27) DateJuly 13, 2017 CONFIDENTIAL 5. Mechanical Specifications Drawing No.JW204430XX Top view silex technology, Inc.
(20/27) DateJuly 13, 2017 CONFIDENTIAL 6. Indication specifications Drawing No.JW204430XX Warning message of W52/53 for Japan MIC Mark and number FCC ID IC ID Serial number
(MAC Address the last 6 digits) 2D Code Family product indication Format:Data Matrix
(Serial number) Country of origin Board number Manufacturer name Model name The Label is placed on the RF shielding cas. silex technology, Inc.
(21/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX System requirements and quick start guide 7. 1) System requirements Prepare the host CPU board whose spec requirements are shown below. System pecifications Items MCU (CPU) Descriptions ARM based 1.0GHz or greater SoC from any companies. Eg. Freescale i.MX6SX 1200MHz Memory size ROM : 512MB, RAM : 1GB or greater OS Linux any kernel distribution Host interface SDIO 3.0 / UART 2) Solder down SX-SDMAC-2832 on the CPU board. See system block diagram. 3) Connect the Antenna to the SX-SDAMC-2832S. See Antenna location. 4) Install the driver which is provided by Silex to the CPU board. Any other 3rd partys software shall be rejected due to Subsystem ID mismatch. 5) Set wireless setting via serial console and connect to the AP. System block diagram silex technology, Inc.
(22/27) DateJuly 13, 2017 CONFIDENTIAL SX-SDMAC-2832SSX-SDMAC-2832S+CPU board Antenna location Attach the PCB antenna to MHF-1 connector on the SX-SDMAC module which is mounted on the 3rd vendors CPU board. The PCB antenna must be placed on the dielectric material like the plastic case and must be 20 mm or more far from the CPU board. Drawing No.JW204430XX silex technology, Inc.
(23/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX 8. Notifications FCCID N6C-PMACS IC 4908A-PMACS Regulatory notice Channel Selection For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Fcc Rules Part 15 FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Rules, Part 15 15.19(a)(3) / IC RSS Gen 8.4 Below sentences must be indicated on the final product which contains this module inside. This device complies with part 15 of FCC Rules and Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : 1) lappareil ne doit pas produire de brouillage; 2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FCC Rules Part 15 Subpart C 15.247 and Subpart E / IC RSS-102 2.6 This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from persons body. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices d'exposition et d exposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain. silex technology, Inc.
(24/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX FCC Rules Part 15 Subpart E 15.407(c) Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. FCC Rules Part 15 Subpart E 15.407(g) Frequency Tolerance: +/-20 ppm FCC Rules Part 15 Subpart C 15.247(g) / Subpart E This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. RSS-Gen 8.3 This radio transmitter 4908A-PMACS has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le numro IC du prsent metteur radio 4908A-PMACS a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu pour ce type, sont strictement interdits pour l'exploitation avec cet appareil. Certified antenna list Part number Vendors Antenna type Remarks 2.4GHz W52 W53 W56 W58 Units Antenna Gain 146153 Molex PCB type di-pole antenna
+3.25
+5.00
+5.00 +5.00 +5.00 dBi Exclude cable loss AA258 (H2B1PC1A1C) Unictron PCB type di-pole antenna
+2.90
+4.40
+4.40 +4.40 +4.40 dBi Exclude cable loss AA222 (H2B1PD1A1C) Unictron PCB type di-pole antenna
+2.80
+4.20
+4.20 +4.20 +4.20 dBi Exclude cable loss PA391-222 PFU PCB type di-pole antenna
+3.00
+3.00
+3.00 +3.00 +3.00 dBi Exclude cable loss silex technology, Inc.
(25/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX RSS-247 Issue 1 May 2015 Radio Standards Specification RSS-247, Issue 1, Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices, is a new standard to replace annexes 8 and 9 of RSS-210, Issue 8, Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment. At the date of publication of this standard, devices covered under the scope of this document will no longer be certified under RSS-210, Issue 8. Le Cahier des normes radiolectriques 247, 1re dition, Les systmes de transmission numrique (STN), les systmes sauts de frquence (SSF) et les dispositifs de rseaux locaux exempts de licence (RL-EL), remplace les annexes 8 et 9 du CNR-210, 8e dition, Appareils radio exempts de licence (pour toutes les bandes de frquences) : matriel de catgorie I. la date de publication de la prsente norme, les dispositifs viss par ce document ne seront plus certifis conformment au CNR-210, 8e dition. Frequency Band 5150 5250 MHz LE-LAN devices are restricted to indoor operation only in the band 5150-5250 MHz. Les dispositifs LAN-EL sont restreints une utilisation l'intrieur, dans la bande 5150-5250MHz. High-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Les radars de haute puissance sont dsigns comme utilisateurs principaux (cest- dire utilisateurs prioritaires) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et que ces radars peuvent provoquer du brouillage et/ou des dommages aux dispositifs LAN-EL. silex technology, Inc.
(26/27) DateJuly 13, 2017 CONFIDENTIAL Drawing No.JW204430XX WARNING The FCC / The Industry Canadaregulations provide that changes or modifications not expressly approved by the party responsible for compliance could void the usersauthority to operate the equipment. Manual and Product Labeling information To The End User The end user manual shall include all required regulatory information/warning as show in this manual.And when this module is installed in the host product, you must include a Contain FCC ID : N6C-PMACSand a Contain IC: 4908A-PMACS in the label of the host product. This module is designed for embedded purpose into the general electric devices, and is not designed for high reliability demands like aircraft instruments, nuclear control instruments, high reliability medical instruments, high reliability security instruments or any other devices required extremely high reliability and quality. As this module communicates by radio wave, it is strongly recommended to use some security system to prevent unexpected information leakage to others. This module is a radio module for embedded purpose. Please understand functions and features of this module, and evaluate as the final product which has this module embedded. Also, as evaluation of EMC conformity of this module has not been performed, EMC conformity evaluation and application must be performed with the final product which this module is embedded. This module will effect to some other device or be affected by the some other device using the same frequency band.Please investigate the environment to use this module beforehand. Disassembling or modifying the radio module leads to punishment based on radio law. This module is the embedded module that has the exposed connectors or some devices.Please be careful for electro static, condensing, and other dusts. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. IMPORTANT NOTE: In the event that these conditions cannot be met (for example co-location with another transmitter), then the FCC / IC authorization is no longer considered valid and the FCC / IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC / IC authorization. As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc. silex technology, Inc.
(27/27) DateJuly 13, 2017 CONFIDENTIAL
This product uses the FCC Data API but is not endorsed or certified by the FCC