| submitted | available | document details (if available) | source link |
|---|---|---|---|
| Microsoft Word - WT41-E_Datasheet.doc rahikpa Acrobat Distiller 9.4.5 (Windows) |
| various | User manual | Users Manual | 530.02 KiB |
WT41-E DATA SHEET Friday, 09 September 2011 Version 1.1 Copyright 2000-2011 Bluegiga Technologies All rights reserved. Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual. Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. Bluegigas products are not authorized for use as critical components in life support devices or systems. The WRAP is a registered trademark of Bluegiga Technologies The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners. Bluegiga Technologies Oy VERSION HISTORY Version Comment 1.1 1.0 Power vs supply voltage figure added Release Bluegiga Technologies Oy TABLE OF CONTENTS WT41-E ................................................................................................................................................................ 1 Data Sheet ........................................................................................................................................................... 1 1 Ordering Information..................................................................................................................................... 7 2 Pinout and Terminal Description .................................................................................................................. 8 3 Electrical Characteristics ............................................................................................................................ 11 3.1 Absolute Maximum Ratings ................................................................................................................ 11 3.2 Recommended Operating Conditions ................................................................................................. 11 PIO Current Sink and Source Capability ............................................................................................. 11 3.3 3.4 Transmitter Performance For BDR ..................................................................................................... 12 3.5 Radiated Spurious Emissions ............................................................................................................. 13 3.6 Receiver Performance ........................................................................................................................ 14 3.7 Current Consumption .......................................................................................................................... 14 3.8 Antenna Specification ......................................................................................................................... 15 4 Layout Guidelines ....................................................................................................................................... 18 5 UART Interface ........................................................................................................................................... 19 5.1 UART Bypass ...................................................................................................................................... 21 5.2 UART Configuration While Reset is Active ......................................................................................... 21 5.3 UART Bypass Mode ............................................................................................................................ 21 6 USB Interface ............................................................................................................................................. 22 6.1 USB Data Connections ....................................................................................................................... 22 6.2 USB Pull-Up resistor ........................................................................................................................... 22 6.3 USB Power Supply .............................................................................................................................. 22 Self-Powered Mode ............................................................................................................................. 22 6.4 6.5 Bus-Powered Mode ............................................................................................................................. 23 6.6 USB Suspend Current ......................................................................................................................... 24 6.7 USB Detach and Wake-Up Signaling ................................................................................................. 24 6.8 USB Driver .......................................................................................................................................... 25 6.9 USB v2.0 Compliance and Compatibility ............................................................................................ 25 7 Serial Peripheral Interface (SPI) ................................................................................................................. 26 8 PCM Codec Interface ................................................................................................................................. 27 8.1 PCM Interface Master/Slave ............................................................................................................... 27 8.2 Long Frame Sync ................................................................................................................................ 28 8.3 Short Frame Sync ............................................................................................................................... 28 8.4 Multi-slot Operation ............................................................................................................................. 29 8.5 GCI Interface ....................................................................................................................................... 29 Slots and Sample Formats .................................................................................................................. 30 8.6 8.7 Additional Features ............................................................................................................................. 31 Bluegiga Technologies Oy 9 10 11 8.8 8.9 9.1 PCM_CLK and PCM_SYNC Generation ............................................................................................ 31 PCM Configuration .............................................................................................................................. 32 I/O Parallel Ports ........................................................................................................................................ 34 PIO Defaults ........................................................................................................................................ 34 Reset ....................................................................................................................................................... 35 Pin States on Reset ..................................................................................................................... 36 Certifications ........................................................................................................................................... 37 Bluetooth ...................................................................................................................................... 37 FCC and IC .................................................................................................................................. 37 11.2.1 FCC et IC ..................................................................................................................................... 39 CE ................................................................................................................................................ 41 Japan ........................................................................................................................................... 41 Qualified Antenna Types for WT41-E .......................................................................................... 41 Contact Information................................................................................................................................. 43 10.1 11.1 11.2 11.3 11.4 11.5 12 Bluegiga Technologies Oy WT41 Bluetooth Module DESCRIPTION WT41-E is a long range class 1, Bluetooth 2.1 +
EDR module. WT41-E is a highly integrated and sophisticated Bluetooth module, containing all the necessary elements from Bluetooth radio and a fully implemented protocol stack. Therefore WT41-E provides an ideal solution for developers who want to integrate Bluetooth wireless technology into their design with limited knowledge of Bluetooth and RF technologies. WT41-E is optimized for long range applications and since it contains a RF power amplifier, low noise amplifier and a u.fi connector for an external 2 dBi dipole antenna. With 115 dB radio budget WT41-E can reach over 1 km range in line off sight. By default WT41-E module is equipped with powerful and easy-to-use iWRAP firmware. iWRAP enables users to access Bluetooth functionality with simple ASCII commands delivered to the module over serial interface - it's just like a Bluetooth modem. APPLICATIONS:
Hand held terminals Industrial devices Point-of-Sale systems PCs Personal Digital Assistants (PDAs) Computer Accessories Access Points Automotive Diagnostics Units FEATURES:
Fully Qualified Bluetooth v2.1 + EDR end product, CE and FCC and IC TX power : 19 dBm RX sensitivity : -92 dBm Higly efficient chip antenna, U.FL connector or RF pin Class 1, range up to 800 meters Industrial temperature range from -40oC to
+85oC RoHS Compliant USB interface (USB 2.0 compatible) UART with bypass mode Support for 802.11 Coexistence 6 x GPIO 1 x 8-bit AIO Integrated iWRAPTM Bluetooth stack or HCI firmware Bluegiga Technologies Oy 1 Ordering Information WT41-E-HCI Firmware HCI = HCI firmware (Bluetooth 2.0 + EDR) HCI21= HCI firmware (Bluetooth 2.1 + EDR) HCI30= HCI firmware (Bluetooth 3.0) AI
AI3 =
AI4 =
iWRAP 2.2.0 iWRAP 3.0.0 iWRAP 4.0.0 HW version E
= u.fl connector Product series Bluegiga Technologies Oy Page 7 of 43 2 Pinout and Terminal Description 9 5 8 5 7 5 6 5 5 5 4 5 3 5 D N G D N G D N G D N G D N G D N G D N G 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 GND GND GND GND GND GND GND GND GND VDD_PA PIO2 PIO3 UART_RTS UART_RX GND USB+
USB-
UART_CTS PCM_IN PCM_CLK PCM_SYNC GND Pins 1 and 52 (GND) are not connected and have been removed 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 RF RFGND GND GND GND GND GND GND AIO UART_TX PIO5 SPI_MOSI SPI_MISO SPI_CLK SPI_CSB GND PIO7 PIO6 RESET VDD GND T U O _ M C P D N G D N G D N G D N G 4 O P D N G I 4 2 5 2 6 2 7 2 8 2 9 2 0 3 NC RESET GND RF RFGND VDD_PA VDD Figure 1: WT41-E pin out PIN NUMBER 1, 52 33 2-10, 16, 23,24,26-
28, 30, 31,36,44-
49 53-59 51 50 11 32 PAD TYPE Not connected Input, weak internal pull-
up GND RF output GND Supply voltage Supply voltage DESCRIPTION Pins 1 and 52 (GND) have been removed from the module. Active low reset. Keep low for >5 ms to cause a reset GND RF output for WT41-N. For WT41-A and WT41-E this pin is not connected RF ground. Connected to GND internally to the module. Supply voltage for the RF power amplifier and the low noise amplifier of the module Supply voltage for BC4 and the flash memory Table 1: Supply and RF Terminal Descriptions Bluegiga Technologies Oy Page 8 of 43 PIO PORT PIN NUMBER PAD TYPE DESCRIPTION PIO[2]
PIO[3]
PIO[4]
PIO[5]
PIO[6]
PIO[7]
AIO[1]
12 13 29 41 34 35 43 Bi-directional, programmamble strength internal pull-down/pull-up Programmamble input/output line Bi-directional, programmamble strength internal pull-down/pull-up Programmamble input/output line Bi-directional, programmamble strength internal pull-down/pull-up Programmamble input/output line Bi-directional, programmamble strength internal pull-down/pull-up Programmamble input/output line Bi-directional, programmamble strength internal pull-down/pull-up Programmamble input/output line Bi-directional, programmamble strength internal pull-down/pull-up Bi-directional Programmamble input/output line Programmamble analog input/output line Table 2: GPIO Terminal Descriptions SPI INTERFACE PIN NUMBER PCM_OUT PCM_IN PCM_SYNC PCM_CLK 25 20 22 21 UART Interfaces PIN NUMBER UART_TX UART_RTS#
UART_RX UART_CTS#
42 14 15 19 PAD TYPE DESCRIPTION CMOS output, tri-state, weak internal pull-down Synchronous data output CMOS input, weak internal pull-down Bi-directional, weak internal pull-down Bi-directional, weak internal pull-down Synchronous data input Synchronous data sync Synchronous data clock Table 3: PCM Terminal Descriptions PAD TYPE DESCRIPTION CMOS output, tri-
state, with weak internal pull-up CMOS output, tri-
state, with weak internal pull-up CMOS input, tri-
state, with weak internal pull-down CMOS input, tri-
state, with weak internal pull-down Table 4: UART Terminal Descriptions UART data output, active high UART request to send, active low UART data input, active high UART clear to send, active low Bluegiga Technologies Oy Page 9 of 43 USB Interfaces PIN NUMBER PAD TYPE DESCRIPTION USB+
USB-
SPI INTERFACE SPI_MOSI SPI_CS#
SPI_CLK SPI_MISO 17 18 Bidirectional Bidirectional USB data plus with selectable internal 1.5k pull-up resistor USB data minus Table 5: USB Terminal Descriptions PIN NUMBER 40 37 38 39 PAD TYPE DESCRIPTION CMOS input with weak internal pull-down CMOS input with weak internal pull-up CMOS input with weak internal pull-down CMOS output, tristate, with weak internal pull down SPI data input Chip select for Serial Peripheral Interface, active low SPI clock SPI data output Table 6: Terminal Descriptions Bluegiga Technologies Oy Page 10 of 43 Electrical Characteristics 3 3.1 Absolute Maximum Ratings Rating Storage Temperature VDD_PA, VDD Other Terminal Voltages Min
-40
-0.4 Max 85 3.6 VSS-0.4 VDD+0.4 3.2 Recommended Operating Conditions Table 7: Absolute Maximum Ratings Rating Operating Temperature Range VDD_PA, VDD *) Max 85 3.6
*) VDD_PA has an effect on the RF output power. Min
-40 3.0 Table 8: Recommended Operating Conditions 3.3 PIO Current Sink and Source Capability Unit C V V Unit C V Figure 2: WT41-E PIO Current Drive Capability Bluegiga Technologies Oy Page 11 of 43 3.4 Transmitter Performance For BDR Antenna gain 2.3dBi taken into account RFCharacetristics,VDD=3.3V@room temperatureunlessotherwisespecified Min Typ Max Bluetooth Specification Unit maximumRFTransmitPower 17 19 20 20 dBm RFpowervariationovertemperaturerange RFpowervariationoversupplyvoltagerange(*
RFpowervariationoverBTband RFpowercontrolrange(*
0.1 10 20dBbandwidthformodulatedcarrier F=F02MHz F=F03MHz F=F0>3MHz Driftrate F1avg F1max F2avg/F1avg ACP(1 1 2 2 19 20 40 40 0.5 942 7 169 161 1.1 1000 20 40 40
+/25 140<175 140<175
>=0.8 dB dB dB kHz kHz kHz kHz Table 9: Transmitter performance for BDR Figure 3: Typical TX power as a function of VDD_PA Bluegiga Technologies Oy Page 12 of 43 3.4.1 Radiated Spurious Emissions Measured from WT41-E evaluation board Standard Band/Frequency FCCpart15 transmitter spurious emissions ETSIEN300328 transmitter spurious emissions ETSIEN300328 receiverspurious Standard Min
(AVG/
PEAK) Typ
(AVG/
PEAK) 52 51 Max
(AVG/
PEAK) 54/58 54/58 50/60 52/63 52/65 54/67 50 58 39 36 LimitbytheStandard
(AVG/PEAK) 54/74 54/74 54/74 54/74 20 20 30 2ndharmonic 3rdharmonic Bandedge 2390MHz Bandedge 2483.5MHz Bandedge 2400MHz
(conducted) Bandedge 2483.5MHz
(conducted) Bandedge 2400MHz 2ndharmonic 3rdharmonic 30 30 47 47 Table 10: Radiated spurious emission for WT41-E 41 41 52
(24002479)MHz
(16001653)MHz Unit dBuV/m dBuV/m dBuV/m dBuV/m dBc dBc dBm dBm dBm dBm dBm 2ndharmonic 3rdharmonic Bandedge 2390MHz Bandedge 2483.5MHz Bandedge2400 MHz(conducted) Bandedge 3483.5MHz
(conducted) Bandedge 2400MHz 2ndharmonic 3rdharmonic FCCpart15 transmitter spuriousemissions ETSIEN300328 transmitter spuriousemissions ETSIEN300328 receiverspurious
(24002479)MHz
(16001653)MHz Min
(AVG/
PEAK) Typ(AVG
/PEAK)
<48/55
<48/51 Max
(AVG/
PEAK) 50/56 48/52 50/60 52/63 52/65 54/67 50 58 39 36 LimitbytheStandard
(AVG/PEAK) Unit 54/74 54/74 54/74 54/74 20 20 30 30 30 47 47 dBuV/m dBuV/m dBuV/m dBuV/m dBc dBc dBm dBm dBm dBm dBm Table 11: Radiated spurious emission for WT41-E Bluegiga Technologies Oy Page 13 of 43 3.5 Receiver Performance Antenna gain not taken into account RFcharacteristis,VDD=3.3V, roomtemperature(**
Packettype Min Typ Max DH1 DH3 DH5 2DH1 2DH3 2DH5 3DH1 3DH3 3DH5 92 92 91 94 93 93 88 85 84 TBD Table 12: Receiver sensitivity Sensitivityfor0.1%BER Sensitivityvariationover temperaturerange 3.6 Current Consumption Bluetooth Spefication 70 Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm Opearationmode Standby,pagemode0 TX3DH5 TX2DH5 TX3DH3 TX2DH3 TX2DH1 TXDH5 TXDH1 RX Deepsleep Inquiry Peak(mA) AVG(mA) 100.5 99.3 98.1 98.1 98.7 164 166 56.8 169.3 2.1 77.6 77.6 71.1 71.2 51.6 120 67.3 52.6 0.36 58.7 Table 13: Current consumption Bluegiga Technologies Oy Page 14 of 43 3.7 Antenna Specification WT41-E is designed and qualified to be used with a 2.14 dBi dipole antenna. Any dipole antenna with the same or less gain can be used with WT41-E as far as the technical information of the antenna is provided for Bluegiga for approval. Any antenna approved by Bluegiga can be used with WT41-E without additional applications to FCC or IC. Table 20 on page 42 lists the antennas pre-approved by Bluegiga. Using an antenna of a different type (i.e. different radiation pattern) or higher gain will require a permissive change for the certifications. Please contact support@bluegiga.com for details Bluegiga Technologies Oy Page 15 of 43 Physical Dimensions Figure 4: Physical dimensions (top view) Figure 5: Dimensions for the RF pin (top view) Bluegiga Technologies Oy Page 16 of 43 25.3mm 35.3mm 3.35mm 14.0mm 11.4mm 32.6mm Figure 6: Dimensions of WT41-E Figure 7: Recommended land pattern Bluegiga Technologies Oy Page 17 of 43 4 Layout Guidelines Use good layout practices to avoid excessive noise coupling to supply voltage traces or sensitive analog signal traces, such as analog audio signals. If using overlapping ground planes use stitching vias separated by max 3 mm to avoid emission from the edges of the PCB. Connect all the GND pins directly to a solid GND plane and make sure that there is a low impedance path for the return current following the signal and supply traces all the way from start to the end. A good practice is to dedicate one of the inner layers to a solid GND plane and one of the inner layers to supply voltage planes and traces and route all the signals on top and bottom layers of the PCB. This arrangement will make sure that any return current follows the forward current as close as possible and any loops are minimized. Figure 8: Typical 4-layer PCB construction Signals GND Power Signals Overlapping GND layers without GND stitching vias Overlapping GND layers with GND stitching vias shielding the RF energy Figure 9: Use of stitching vias to avoid emissions from the edges of the PCB Bluegiga Technologies Oy Page 18 of 43 5 UART Interface This is a standard UART interface for communicating with other serial devices.WT41-E UART interface provides a simple mechanism for communicating with other serial devices using the RS232 protocol. Four signals are used to implement the UART function. When WT41-E is connected to another digital device, UART_RX and UART_TX transfer data between the two devices. The remaining two signals, UART_CTS and UART_RTS, can be used to implement RS232 hardware flow control where both are active low indicators. All UART connections are implemented using CMOS technology and have signalling levels of 0V and VDD. UART configuration parameters, such as data rate and packet format, are set using WT41-E software. Note:
In order to communicate with the UART at its maximum data rate using a standard PC, an accelerated serial port adapter card is required for the PC. Table 14: Possible UART Settings The UART interface is capable of resetting WT41-E upon reception of a break signal. A break is identified by a continuous logic low (0V) on the UART_RX terminal, as shown in Figure 10. If tBRK is longer than the value, defined by PSKEY_HOST_IO_UART_RESET_TIMEOUT, (0x1a4), a reset will occur. This feature allows a host to initialise the system to a known state. Also, WT41-E can emit a break character that may be used to wake the host. Figure 10: Break Signal Table 17 shows a for PSKEY_UART_BAUD_RATE (0x204). There is no requirement to use these standard values. Any data rate within the supported range can be set in the PS Key according to the formula in Equation XXX list of commonly used data their associated values rates and Bluegiga Technologies Oy Page 19 of 43 Equation 1: Data Rate Table 15: Standard Data Rates Bluegiga Technologies Oy Page 20 of 43 5.1 UART Bypass Figure 11: UART Bypass Architecture 5.2 UART Configuration While Reset is Active The UART interface for WT41-E while the chip is being held in reset is tristate. This will allow the user to daisy chain devices onto the physical UART bus. The constraint on this method is that any devices connected to this bus must tristate when WT41-E reset is de-asserted and the firmware begins to run. 5.3 UART Bypass Mode Alternatively, for devices that do not tristate the UART bus, the UART bypass mode on BlueCore4-External can be used. The default state of BlueCore4-External after reset is de-asserted; this is for the host UART bus to be connected to the BlueCore4-External UART, thereby allowing communication to BlueCore4-External via the UART. All UART bypass mode connections are implemented using CMOS technology and have signalling levels of 0V and VDD. In order to apply the UART bypass mode, a BCCMD command will be issued to BlueCore4-External. Upon this issue, it will switch the bypass to PIO[7:4] as Figure 11 indicates. Once the bypass mode has been invoked, WT41-E will enter the Deep Sleep state indefinitely. In order to re-establish communication with WT41-E, the chip must be reset so that the default configuration takes effect. It is important for the host to ensure a clean Bluetooth disconnection of any active links before the bypass mode is invoked. Therefore, it is not possible to have active Bluetooth links while operating the bypass mode. The current consumption for a device in UART bypass mode is equal to the values quoted for a device in standby mode. Bluegiga Technologies Oy Page 21 of 43 6 USB Interface This is a full speed (12Mbits/s) USB interface for communicating with other compatible digital devices. WT41-
E acts as a USB peripheral, responding to requests from a master host controller such as a PC. The USB interface is capable of driving a USB cable directly. No external USB transceiver is required. The device operates as a USB peripheral, responding to requests from a master host controller such as a PC. Both the OHCI and the UHCI standards are supported. The set of USB endpoints implemented can behave as specified in the USB section of the Bluetooth v2.1 + EDR specification or alternatively can appear as a set of endpoints appropriate to USB audio devices such as speakers. As USB is a master/slave oriented system (in common with other USB peripherals), WT41-E only supports USB Slave operation. 6.1 USB Data Connections The USB data lines emerge as pins USB_DP and USB_DN. These terminals are connected to the internal USB I/O buffers of the BlueCore4-External, therefore, have a low output impedance. To match the connection to the characteristic impedance of the USB cable, resistors must be placed in series with USB_DP/USB_DN and the cable. 6.2 USB Pull-Up resistor WT41-E features an internal USB pull-up resistor. This pulls the USB_DP pin weakly high when WT41-E is ready to enumerate. It signals to the PC that it is a full speed (12Mbits/s) USB device. The USB internal pull-up is implemented as a current source, and is compliant with section 7.1.5 of the USB specification v1.2. The internal pull-up pulls USB_DP high to at least 2.8V when loaded with a 15k 5% pull-
down resistor (in the hub/host) when VDD_PADS = 3.1V. This presents a Thevenin resistance to the host of at least 900. Alternatively, an external 1.5k pull-up resistor can be placed between a PIO line and D+ on the USB cable. The firmware must be alerted to which mode is used by setting PSKEY_USB_PIO_PULLUP appropriately. The default setting uses the internal pull-up resistor. 6.3 USB Power Supply The USB specification dictates that the minimum output high voltage for USB data lines is 2.8V. To safely meet the USB specification, the voltage on the VDD supply terminal must be an absolute minimum of 3.1V. Bluegiga recommends 3.3V for optimal USB signal quality. 6.4 Self-Powered Mode In self-powered mode, the circuit is powered from its own power supply and not from the VBUS (5V) line of the USB cable. It draws only a small leakage current (below 0.5mA) from VBUS on the USB cable. This is the easier mode for which to design, as the design is not limited by the power that can be drawn from the USB hub or root port. However, it requires that VBUS be connected to WT41-E via a resistor network (Rvb1 and Rvb2), so WT41-E can detect when VBUS is powered up. BlueCore4-External will not pull USB_DP high when VBUS is off. Self-powered USB designs (powered from a battery or PSU) must ensure that a PIO line is allocated for USB pullup purposes. A 1.5k 5% pull-up resistor between USB_DP and the selected PIO line should be fitted to the design. Failure to fit this resistor may result in the design failing to be USB compliant in self-powered mode. The internal pull-up in BlueCore is only suitable for bus-powered USB devices, e.g., dongles. Bluegiga Technologies Oy Page 22 of 43 Figure 12: USB Connections for Self-Powered Mode The terminal marked USB_ON can be any free PIO pin. The PIO pin selected must be registered by setting PSKEY_USB_PIO_VBUS to the corresponding pin number. Figure 13: USB Interface Component Values 6.5 Bus-Powered Mode In bus-powered mode, the application circuit draws its current from the 5V VBUS supply on the USB cable. WT41-E negotiates with the PC during the USB enumeration stage about how much current it is allowed to consume. On power-up the device must not draw more than 100 mA but after being configured it can draw up to 500 mA. For WT41-E, the USB power descriptor should be altered to reflect the amount of power required. This is accomplished by setting PSKEY_USB_MAX_POWER (0x2c6). This is higher than for a Class 2 application due to the extra current drawn by the Transmit RF PA. By default for WT41-E the setting is 300 mA. When selecting a regulator, be aware that VBUS may go as low as 4.4V. The inrush current (when charging reservoir and supply decoupling capacitors) is limited by the USB specification. See the USB Specification. Some applications may require soft start circuitry to limit inrush current if more than 10uF is present between VBUS and GND. The 5V VBUS line emerging from a PC is often electrically noisy. As well as regulation down to 3.3V and 1.8V, applications should include careful filtering of the 5V line to attenuate noise that is above the voltage regulator bandwidth. Excessive noise on WT41-E supply pins will result in reduced receiver sensitivity and a distorted RF transmit signal. Bluegiga Technologies Oy Page 23 of 43 Figure 14: USB Connections for Bus-Powered Mode 6.6 USB Suspend Current All USB devices must permit the USB controller to place them in a USB suspend mode. While in USB Suspend, bus-powered devices must not draw more than 2.5mA from USB VBUS (self-powered devices may draw more than 2.5mA from their own supply). This current draw requirement prevents operation of the radio by bus-powered devices during USB Suspend. When computing suspend current, the current from VBUS through the bus pull-up and pull-down resistors must be included. The pull-up resistor at the device is 1.5 k. (nominal). The pull-down resistor at the hub is 14.25k. to 24.80k. The pull-up voltage is nominally 3.3V, which means that holding one of the signal lines high takes approximately 200uA, leaving only 2.3mA available from a 2.5mA budget. Ensure that external LEDs and/or amplifiers can be turned off by BlueCore4-External. The entire circuit must be able to enter the suspend mode. 6.7 USB Detach and Wake-Up Signaling lines are shared with PIO pins and can be assigned WT41-E can provide out-of-band signaling to a host controller by using the control lines called USB_DETACH and USB_WAKE_UP. These are outside the USB specification (no wires exist for them inside the USB cable), but can be useful when embedding WT41-E into a circuit where no external USB is visible to the user. Both control to any PIO pin by setting PSKEY_USB_PIO_DETACH and PSKEY_USB_PIO_WAKEUP to the selected PIO number. USB_DETACH is an input which, when asserted high, causes WT41-E to put USB_DN and USB_DP in high impedance state and turns off the pull-up resistor on DP. This detaches the device from the bus and is logically equivalent to unplugging the device. When USB_DETACH is taken low, WT41-E will connect back to USB and await enumeration by the USB host. USB_WAKE_UP is an active high output (used only when USB_DETACH is active) to wake up the host and allow USB communication to recommence. It replaces the function of the software USB WAKE_UP message
(which runs over the USB cable) and cannot be sent while BlueCore4-External is effectively disconnected from the bus. Bluegiga Technologies Oy Page 24 of 43 Figure 15: USB_Detach and USB_Wake_Up Signals 6.8 USB Driver A USB Bluetooth device driver is required to provide a software interface between BlueCore4-External and Bluetooth software running on the host computer. Please, contact support@bluegiga.com for suitable drivers. 6.9 USB v2.0 Compliance and Compatibility Although WT41-E meets the USB specification, CSR cannot guarantee that an application circuit designed around the module is USB compliant. The choice of application circuit, component choice and PCB layout all affect USB signal quality and electrical characteristics. The information in this document is intended as a guide and should be read in association with the USB specification, with particular attention being given to Chapter 7. Independent USB qualification must be sought before an application is deemed USB compliant and can bear the USB logo. Such qualification can be obtained from a USB plugfest or from an independent USB test house. Terminals USB_DP and USB_DN adhere to the USB Specification v2.0 (Chapter 7) electrical requirements. BlueCore4-External is compatible with USB v2.0 host controllers; under these circumstances the two ends agree the mutually acceptable rate of 12Mbits/s according to the USB v2.0 specification. Bluegiga Technologies Oy Page 25 of 43 7 Serial Peripheral Interface (SPI) The SPI port can be used for system debugging. It can also be used for programming the Flash memory and setting the PSKEY configurations. WT41-E uses 16-bit data and 16-bit address serial peripheral interface, where transactions may occur when the internal processor is running or is stopped. SPI interface is connected using the MOSI, MISO, CSB and CLK pins. Please, contact support@bluegiga.com for detailed information about the instruction cycle. Bluegiga Technologies Oy Page 26 of 43 8 PCM Codec Interface PCM is a standard method used to digitize audio (particularly voice) for transmission over digital communication channels. Through its PCM interface, WT41-E has hardware support for continual transmission and reception of PCM data, thus reducing processor overhead for wireless headset applications. WT41-E offers a bidirectional digital audio interface that routes directly into the baseband layer of the on-chip firmware. It does not pass through the HCI protocol layer. Hardware on WT41-E allows the data to be sent to and received from a SCO connection. Up to three SCO connections can be supported by the PCM interface at any one time. WT41-E can operate as the PCM interface master generating an output clock of 128, 256 or 512kHz. When configured as PCM interface slave, it can operate with an input clock up to 2048kHz. WT41-E is compatible with a variety of clock formats, including Long Frame Sync, Short Frame Sync and GCI timing environments. It supports 13-bit or 16-bit linear, 8-bit -law or A-law companded sample formats at 8ksamples/s and can receive and transmit on any selection of three of the first four slots following PCM_SYNC. The PCM configuration options are enabled by setting PSKEY_PCM_CONFIG32. WT41-E interfaces directly to PCM audio devices. NOTE: Analog audio lines are very sensitive to RF disturbance. Use good layout practices to ensure noise less audio. Make sure that the return path for the audio signals follows the forward current all the way as close as possible and use fully differential signals when possible. Do not compromise audio routing. 8.1 PCM Interface Master/Slave When configured as the master of the PCM interface, WT41-E generates PCM_CLK and PCM_SYNC. When configured as the Slave of the PCM interface, WT41-E accepts PCM_CLK rates up to 2048kHz. Figure 16: PCM Interface Master Bluegiga Technologies Oy Page 27 of 43 Figure 17: PCM Interface Slave 8.2 Long Frame Sync Long Frame Sync is the name given to a clocking format that controls the transfer of PCM data words or samples. In Long Frame Sync, the rising edge of PCM_SYNC indicates the start of the PCM word. When WT41-E is configured as PCM master, generating PCM_SYNC and PCM_CLK, then PCM_SYNC is 8-bits long. When WT41-E is configured as PCM Slave, PCM_SYNC may be from two consecutive falling edges of PCM_CLK to half the PCM_SYNC rate, i.e., 62.5s long. Figure 18: Long Frame Sync (Shown with 8-bit Companded Sample) WT41-E samples PCM_IN on the falling edge of PCM_CLK and transmits PCM_OUT on the rising edge. PCM_OUT may be configured to be high impedance on the falling edge of PCM_CLK in the LSB position or on the rising edge. 8.3 Short Frame Sync In Short Frame Sync, the falling edge of PCM_SYNC indicates the start of the PCM word. PCM_SYNC is always one clock cycle long. Bluegiga Technologies Oy Page 28 of 43 Figure 19: Short Frame Sync (Shown with 16-bit Sample) As with Long Frame Sync, WT41-E samples PCM_IN on the falling edge of PCM_CLK and transmits PCM_OUT on the rising edge. PCM_OUT may be configured to be high impedance on the falling edge of PCM_CLK in the LSB position or on the rising edge. 8.4 Multi-slot Operation More than one SCO connection over the PCM interface is supported using multiple slots. Up to three SCO connections can be carried over any of the first four slots. Figure 20: Multi-slot Operation with Two Slots and 8-bit Companded Samples 8.5 GCI Interface WT41-E is compatible with the GCI, a standard synchronous 2B+D ISDN timing interface. The two 64kbits/s B channels can be accessed when this mode is configured. Bluegiga Technologies Oy Page 29 of 43 Figure 21: GCI Interface The start of frame is indicated by the rising edge of PCM_SYNC and runs at 8kHz. With WT41-E in Slave mode, the frequency of PCM_CLK can be up to 4.096MHz. 8.6 Slots and Sample Formats WT41-E can receive and transmit on any selection of the first four slots following each sync pulse. Slot durations can be either 8 or 16 clock cycles. Durations of 8 clock cycles may only be used with 8-bit sample formats. Durations of 16 clocks may be used with 8-bit, 13-bit or 16-bit sample formats. WT41-E supports 13-bit linear, 16-bit linear and 8-bit -law or A-law sample formats. The sample rate is 8ksamples/s. The bit order may be little or big endian. When 16-bit slots are used, the 3 or 8 unused bits in each slot may be filled with sign extension, padded with zeros or a programmable 3-bit audio attenuation compatible with some Motorola codecs. Bluegiga Technologies Oy Page 30 of 43 Figure 22: 16-bit Slot Length and Sample Formats 8.7 Additional Features WT41-E has a mute facility that forces PCM_OUT to be 0. In master mode, PCM_SYNC may also be forced to 0 while keeping PCM_CLK running which some codecs use to control power down. 8.8 PCM_CLK and PCM_SYNC Generation WT41-E has two methods of generating PCM_CLK and PCM_SYNC in master mode. The first is generating these signals by DDS from BlueCore4-External internal 4MHz clock. Using this mode limits PCM_CLK to 128, 256 or 512kHz and PCM_SYNC to 8kHz. The second is generating PCM_CLK and PCM_SYNC by DDS from an internal 48MHz clock (which allows a greater range of frequencies to be generated with low jitter but consumes more power). This second method is selected by setting bit 48M_PCM_CLK_GEN_EN in PSKEY_PCM_CONFIG32. When in this mode and with long frame sync, the length of PCM_SYNC can be either 8 or 16 cycles of PCM_CLK, determined by LONG_LENGTH_SYNC_EN in PSKEY_PCM_CONFIG32. The Equation XXX describes PCM_CLK frequency when being generated using the internal 48MHz clock:
Bluegiga Technologies Oy Page 31 of 43 Equation 2: PCM_CLK Frequency When Being Generated Using the Internal 48MHz Clock The frequency of PCM_SYNC relative to PCM_CLK can be set using Equation XXX:
Equation 3: PCM_SYNC Frequency Relative to PCM_CLK CNT_RATE, CNT_LIMIT and SYNC_LIMIT are set using PSKEY_PCM_LOW_JITTER_CONFIG. As an example, set PSKEY_PCM_LOW_JITTER_CONFIG to 0x08080177. PCM_SYNC PCM_CLK generate 512kHz 8kHz, with to at at 8.9 PCM Configuration The PCM configuration is set using two PS Keys, PSKEY_PCM_CONFIG32 detailed in Table 18 and PSKEY_PCM_LOW_JITTER_CONFIG in Table 19. The default for PSKEY_PCM_CONFIG32 is 0x00800000, i.e., first slot following sync is active, 13-bit linear voice format, long frame sync and interface master generating 256kHz PCM_CLK from 4MHz internal clock with no tri-state of PCM_OUT. Bluegiga Technologies Oy Page 32 of 43 Bit position Description 0 1 2 3 4 5 6 7 8 9 10 11 12 Set to 0 0 selects Master mode with internal generation of PCM_CLK and PCM_SYNC. 1 selects Slave mode requiring externally generated PCM_CLK and PCM_SYNC. This should be set to 1 if 48M_PCM_CLK_GEN_EN (bit 11) is set. 0 selects long frame sync (rising edge indicates start of frame), 1 selects short frame sync (falling edge indicates start of frame). Set to 0 0 selects padding of 8 or 13-bit voice sample into a 16- bit slot by inserting extra LSBs, 1 selects sign extension. When padding is selected with 3-bit voice sample, the 3 padding bits are the audio gain setting; with 8-bit samples the 8 padding bits are zeroes. 0 transmits and receives voice samples MSB first, 1 uses LSB first. 0 drives PCM_OUT continuously, 1 tri-states PCM_OUT immediately after the falling edge of PCM_CLK in the last bit of an active slot, assuming the next slot is not active. 0 tristates PCM_OUT immediately after the falling edge of PCM_CLK in the last bit of an active slot, assuming the next slot is also not active. 1 tristates PCM_OUT after the rising edge of PCM_CLK. 0 enables PCM_SYNC output when master, 1 suppresses PCM_SYNC whilst keeping PCM_CLK running. Some CODECS utilize this to enter a low power state. 1 enables GCI mode. 1 forces PCM_OUT to 0. 0 sets PCM_CLK and PCM_SYNC generation via DDS from internal 4 MHz clock, as for BlueCore4-External. 1 sets PCM_CLK and PCM_SYNC generation via DDS from internal 48 MHz clock. 0 sets PCM_SYNC length to 8 PCM_CLK cycles and 1 sets length to 16 PCM_CLK cycles. Only applies for long frame sync and with 48M_PCM_CLK_GEN_EN set to 1. Name
SLAVE MODE EN SHORT SYNC EN
SIGN EXTENDED EN LSB FIRST EN TX TRISTATE EN TX TRISTATE RISING EDGE EN SYNC SUPPRESS EN GCI MODE EN MUTE EN 48M PCM CLK GEN EN LONG LENGTH SYNC EN
[20:16]
Set to 0b00000. MASTER CLK RATE
[22:21]
ACTIVE SLOT SAMPLE_FORMAT
[26:23]
[28:27]
Selects 128 (0b01), 256 (0b00), 512 (0b10) kHz PCM_CLK frequency when master and 48M_PCM_CLK_GEN_EN (bit 11) is low. Default is 0001. Ignored by firmaware Selects between 13 (0b00), 16 (0b01), 8 (0b10) bit sample with 16 cycle slot duration 8 (0b11) bit sample 8 cycle slot duration. Table 16: PSKEY_PCM_CONFIG32 description Name CNT LIMIT CNT RATE SYNC LIMIT Bit position Description
[12:0]
[23:16]
[31:24]
Table 17: PSKEY_PCM_LOW_JITTER_CONFIG Description Sets PCM_CLK counter limit Sets PCM_CLK count rate. Sets PCM_SYNC division relative to PCM_CLK. Bluegiga Technologies Oy Page 33 of 43 9 I/O Parallel Ports Six lines of programmable bidirectional input/outputs (I/O) are provided. All the PIO lines are power from VDD. PIO lines can be configured through software to have either weak or strong pull-ups or pull-downs. All PIO lines are configured as inputs with weak pull-downs at reset. Any of the PIO lines can be configured as interrupt request lines or as wake-up lines from sleep modes. WT41-E has a general purpose analogue interface pin AIO[1]. This is used to access internal circuitry and control signals. It may be configured to provide additional functionality. Auxiliary functions available via AIO[1] include an 8-bit ADC and an 8-bit DAC. Typically the ADC is used for battery voltage measurement. Signals selectable at this pin include the band gap reference voltage and a variety of clock signals: 48, 24, 16, 8MHz and the XTAL clock frequency. When used with analogue signals, the voltage range is constrained by the analogue supply voltage internally to the module (1.8V). When configured to drive out digital level signals (e.g., clocks), the output voltage level is determined by VDD. 9.1 PIO Defaults Bluegiga cannot guarantee that these terminal functions remain the same. Refer to the software release note for the implementation of these PIO lines, as they are firmware build-specific. Bluegiga Technologies Oy Page 34 of 43 10 Reset WT41-E may be reset from several sources: RESET pin, power on reset, a UART break character or via software configured watchdog timer. The RESET pin is an active low reset and is internally filtered using the internal low frequency clock oscillator. A reset will be performed between 1.5 and 4.0ms following RESETB being active. It is recommended that RESET be applied for a period greater than 5ms. The power on reset occurs when the VDD_CORE supply internally to the module falls below typically 1.5V and is released when VDD_CORE rises above typically 1.6V. At reset the digital I/O pins are set to inputs for bidirectional pins and outputs are tri-state. The reset should be held active at power up until all the supply voltages have stabilized to ensure correct operation of the internal flash memory. Following figure shows an example of a simple power up reset circuit. Time constant of the RC circuitry is set so that the supply voltage is safely stabilized before the reset deactivates. Figure 23: Example of a simple power on reset circuit. Bluegiga Technologies Oy Page 35 of 43 10.1 Pin States on Reset PIN NAME PIO[7:2]
PCM_OUT PCM_IN PCM_SYNC PCM_CLK UART_TX UART_RX UART_RTS UART_CTS USB+
USB-
SPI_CSB SPI_CLK SPI_MOSI SPI_MISO AIO[1]
STATE Input with weak pull-down Tri-staed with weak pull-down Input with weak pull-down Input with weak pull-down Input with weak pull-down Output tristated with weak pull-up Input with weak pull-down Output tristated with weak pull-up Input with weak pull-down Input with weak pull-down Input with weak pull-down Input with weak pull-down Input with weak pull-down Input with weak pull-down Output tristated with weak pull-down Output, driving low Table 18: Pin States on Reset Bluegiga Technologies Oy Page 36 of 43 11 Certifications WT41-E is compliant to the following specifications. 11.1 Bluetooth WT41-E module is Bluetooth qualified and listed as a controller subsystem and it is Bluetooth compliant to the following profiles of the core spec version 2.1/2.1+EDR. Baseband HCI Link Manager Radio The radio has been tested using maximum antenna gain of 2.3 dBi and the Bluetooth qualification is valid for any antenna with the same or less gain. 11.2 FCC and IC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter is considered as mobile device and should not be used closer than 20 cm from a human body. To allow portable use in a known host class 2 permissive change is required. Please contact support@bluegiga.com for detailed information. IC Statements:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. If detachable antennas are used:
Bluegiga Technologies Oy Page 37 of 43 This radio transmitter (identify the device by certification number, or model number ifCategory II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. See table 19 for the approved antennas for WT41-E. OEM Responsibilities to comply with FCC and Industry Canada Regulations The WT41-E Module has been certified for integration into products only by OEM integrators under the following conditions:
The antenna(s) must be installed such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and all persons at all times. The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for certain configurations or co-
location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. End Product Labeling The WT41-E Module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:
Contains Transmitter Module FCC ID: QOQWT41E Contains Transmitter Module IC: 5123A-BGTWT41E or Contains FCC ID: QOQWT41E Contains IC: 5123A-BGTWT41E The OEM of the WT41-E Module must only use the approved antenna(s) described in table 19, which have been certified with this module. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. To comply with FCC and Industry Canada RF radiation exposure limits for general population, the antenna(s) used for this transmitter must be installed such that a minimum separation distance of 20cm is maintained between the radiator (antenna) and all persons at all times and must not be co-
located or operating in conjunction with any other antenna or transmitter. Bluegiga Technologies Oy Page 38 of 43 11.2.1 FCC et IC Cet appareil est conforme lalina 15 des rgles de la FCC. Deux conditions sont respecter lors de son utilisation :
(1) cetappareilnedoitpascrerdinterfrencesusceptibledecauserunquelconquedommageet,
(2) cetappareildoitacceptertouteinterfrence,quellequellesoit,ycomprislesinterfrences susceptiblesdentranerunfonctionnementnonrequis. Dclaration de conformit FCC dexposition aux radiofrquences (RF):
Ce matriel respecte les limites dexposition aux radiofrquences fixes par la FCC dans un environnement non contrl. Les utilisateurs finaux doivent se conformer aux instructions dutilisation spcifies afin de satisfaire aux normes dexposition en matire de radiofrquence. Ce transmetteur ne doit pas tre install ni utilis en concomitance avec une autre antenne ou un autre transmetteur. Ce transmetteur est assimil un appareil mobile et ne doit pas tre utilis moins de 20 cm du corps humain. Afin de permettre un usage mobile dans le cadre dun matriel de catgorie 2, il est ncessaire de procder quelques adaptations. Pour des informations dtailles, veuillez contacter le support technique Bluegiga : support@bluegiga.com. Dclaration de conformit IC :
Ce matriel respecte les standards RSS exempt de licence dIndustrie Canada. Son utilisation est soumise aux deux conditions suivantes :
(1) lappareilnedoitcauseraucuneinterfrence,et
(2) lappareildoitacceptertouteinterfrence,quellequellesoit,ycomprislesinterfrences susceptiblesdentranerunfonctionnementnonrequisdelappareil. Selon la rglementation dIndustrie Canada, ce radio-transmetteur ne peut utiliser quun seul type dantenne et ne doit pas dpasser la limite de gain autorise par Industrie Canada pour les transmetteurs. Afin de rduire les interfrences potentielles avec dautres utilisateurs, le type dantenne et son gain devront tre dfinis de telle faon que la puissance isotrope rayonnante quivalente (EIRP) soit juste suffisante pour permettre une bonne communication. Lors de lutilisation dantennes amovibles :
Ce radio-transmetteur (identifi par un numro certifi ou un numro de modle dans le cas de la catgorie II) a t approuv par Industrie Canada pour fonctionner avec les antennes rfrences ci-dessous dans la limite de gain acceptable et limpdance requise pour chaque type dantenne cit. Les antennes non rfrences possdant un gain suprieur au gain maximum autoris pour le type dantenne auquel elles Bluegiga Technologies Oy Page 39 of 43 appartiennent sont strictement interdites dutilisation avec ce matriel. Veuillez vous rfrer au tableau 19 concernant les antennes approuves pour les WT41-E. Les responsabilits de lintgrateur afin de satisfaire aux rglementations de la FCC et dIndustrie Canada :
Les modules WT41-E ont t certifis pour entrer dans la fabrication de produits exclusivement raliss par des intgrateurs dans les conditions suivantes :
Lantenne(oulesantennes)doittreinstalledefaonmaintenirtoutinstantunedistance minimumde20cmentrelasourcederadiation(lantenne)ettoutepersonnephysique. Lemoduletransmetteurnedoitpastreinstallouutilisenconcomitanceavecuneautreantenne ouunautretransmetteur. Tant que ces deux conditions sont runies, il nest pas ncessaire de procder des tests supplmentaires sur le transmetteur. Cependant, lintgrateur est responsable des tests effectus sur le produit final afin de se mettre en conformit avec dventuelles exigences complmentaires lorsque le module est install (exemple :
missions provenant dappareils numriques, exigences vis--vis de priphriques informatiques, etc.) ;
IMPORTANT : Dans le cas o ces conditions ne peuvent tre satisfaites (pour certaines configurations ou installation avec un autre transmetteur), les autorisations fournies par la FCC et Industrie Canada ne sont plus valables et les numros didentification de la FCC et de certification dIndustrie Canada ne peuvent servir pour le produit final. Dans ces circonstances, il incombera lintgrateur de faire rvaluer le produit final
(comprenant le transmetteur) et dobtenir une autorisation spare de la part de la FCC et dIndustrie Canada. Etiquetage du produit final Chaque module WT41-E possde sa propre identification FCC et son propre numro de certification IC. Si lidentification FCC et le numro de certification IC ne sont pas visibles lorsquun module est install lintrieur dun autre appareil, alors lappareil en question devra lui aussi prsenter une tiquette faisant rfrence au module inclus. Dans ce cas, le produit final doit comporter une tiquette place de faon visible affichant les mentions suivantes :
Contient un module transmetteur certifi FCC QOQWT41E Contient un module transmetteur certifi IC 5123A-BGTWT41E ou Inclut la certification FCC QOQWT41E Bluegiga Technologies Oy Page 40 of 43 Inclut la certification IC 5123A-BGTWT41E Lintgrateur du module WT41-E ne doit utiliser que les antennes rpertories dans le tableau 19 certifies pour ce module. Lintgrateur est tenu de ne fournir aucune information lutilisateur final autorisant ce dernier installer ou retirer le module RF, ou bien changer les paramtres RF du module, dans le manuel dutilisation du produit final. Afin de se conformer aux limites de radiation imposes par la FCC et Industry Canada, lantenne (ou les antennes) utilise pour ce transmetteur doit tre installe de telle sorte maintenir une distance minimum de 20cm tout instant entre la source de radiation (lantenne) et les personnes physiques. En outre, cette antenne ne devra en aucun cas tre installe ou utilise en concomitance avec une autre antenne ou un autre transmetteur. 11.3 CE WT41-E meets the requirements of the standards below and hence fulfills the requirements of EMC Directive 89/336/EEC as amended by Directives 92/31/EEC and 93/68/EEC within CE marking requirement. EMC (immunity only) EN 301 489-17 V.1.3.3 in accordance with EN 301 489-1 V1.8.1 Radiated emissions EN 300 328 V1.7.1 11.4 Japan According to Japanese regulations the OEM integrator using a surface mountable module, such as WT41-E, will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate authorization for the radio. WT41-E is tested to meet the technical requirements of a radio for Japanese market. Japans regulations limit the maximum spectral power density to 3mW/MHz. When using AFH the number of active channels can be as low as 20, which will effectively increase the spectral power density. Thus when AFH is in use the transmit power must be decreased nominally below 17 dBm to meet Japan regulations. 11.5 Qualified Antenna Types for WT41-E This device has been designed to operate with a standard 2.14 dBi dipole antenna. Any antenna of a different type or with a gain higher than 2.14 dBi is strictly prohibited for use with this device. Using an antenna of a different type or gain more than 2.14 dBi will require additional testing for FCC, CE and IC. Please, contact support@bluegiga.com for more information. The required antenna impedance is 50 ohms. Bluegiga Technologies Oy Page 41 of 43 Qualified Antenna Types for WT41-E Antenna Type Maximum Gain Dipole 2.14 dBi Table 19: Qualified Antenna Types for WT41-E To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Any standard 2.14 dBi dipole antenna can be used without an additional application to FCC. Table 20 lists approved antennas for WT41-E. Any approved antenna listed in table 20 can be used directly with WT41-E without any additional approval. Any antenna not listed in table 20 can be used with WT41-E as long as detailed information from that particular antenna is provided to Bluegiga for approval. Specification of each antenna used with WT41-E will be filed by Bluegiga. Please, contact support@bluegiga.com for more information. Item Manufacturer Manufacturerspartnumber Measure dGain
(dBi) LinxTechnologiesInc Pulse EAD Antenova Litecon W1030 ANT2.4CWCTSMA 1 1.3 0.4 1.4 0.8 Table 20: Approved Antennas For WT41-E CARATR187001 B4844/B6090 EA79A 1 2 3 4 5 Specifie dGain
(dBi) 2dBi 2dBi 2dBi 2dBi 2dBi MeasureTotal Efficiency(%) 7080 77 60 7682 6070 Bluegiga Technologies Oy Page 42 of 43 12 Contact Information Sales:
Technical support:
sales@bluegiga.com support@bluegiga.com http://www.bluegiga.com/techforum/
orders@bluegiga.com Orders:
Head Office / Finland:
Street Address:
Postal address:
Sales Office / USA:
Phone: +358-9-4355 060 Fax: +358-9-4355 0660 Sinikalliontie 5A 02630 ESPOO FINLAND P.O. BOX 120 02631 ESPOO FINLAND Phone: (781) 556-1039 Bluegiga Technologies, Inc. 99 Derby Street, Suite 200 Hingham, MA 02043 Bluegiga Technologies Oy Page 43 of 43
This product uses the FCC Data API but is not endorsed or certified by the FCC