D205 Bluetooth Speaker Users Manual

Instruction Manual-Travel Thank you for choosing DeFunc Travel Bluetooth Speakers.Please read this guide carefully and follow the instructions to get you started.Dont forgot to read the safety instructions.Keep this guide for future reference.For additional information visit www.defunc.com/troubleshooting.The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. Whats inside this box?

1. 1*DeFunc Travel Bluetooth Speaker 2. 1*Micro USB charging cable 3. 1*AUX cable 4. Warranty Description:

1. ON/OFF 2. Previous/Volume 3. Next/Volume +

4. Play/Pause/Phone button 5. MIC 6. Micro USB Charging Port / AUX in Port 7. Blue LED(Bluetooth) / Red LED(Charging) Specifications:

Supported Profiles: A2DPV1.2,AVRCPV1.0,HFPV1.5,GAVDP1.2 Bluetooth Version: 4.1 Bluetooth Range:33ft (10m) Dimensions: 70*70*70mm Battery: Li-Ion 3.7V, 1000 mAh Charging: DC 5V @ 500 mA Weight: 222g Operation:

Powering On Press and Hold "

" button 2 seconds to power ON, the Blue LED will start to rapid blink . If an Aux cable is connected to the unit, the Blue LED will slow blink, the unit is in Aux-In mode. Powering Off Paired mode:Press and Hold "

" button 2 seconds to disconnect the Bluetooth, then Press and Hold "

"button again to power off . Pairing/AUX mode:Press and Hold "

" button 2seconds to power off Bluetooth Mode Pairing The unit will automatically go into Pairing Mode when it is powered on.Go into your Bluetooth device settings menu and look forDeFunc Travel. After the unit has paired and connected, it will re-connect automatically when the unit is powered on and the device is in range. Note: Bluetooth Timeout :10 minutes Begin Streaming Music Press to start playing music Press and Hold 2 seconds to play the next track Press and Hold 2 seconds to play previous track Press either Aux-In Mode or for volume control. Plug in the supplied 3.5 mm cable into the unit. The other end is connected to your device. the Blue LED will slow blink when inAuxmode. Please note music and volume can be controlled by your device. Making and Receiving Phone Calls When the unit is connected and paired to your device,the unit allows you to make or receive phone calls with its built-in microphone. Charging Attach the USB cable to the unit, and plug into any USB charger. If the unit is completely discharged, it will take approximately 3 hours to fully charge. The Red LED will illuminate during charging, when it has completed, the Red LED will turn off. Note: There will be a beep when the battery is low and needs to be recharged. LED Status Blue LED rapid blink

&

Blue LED solid Bluetooth Mode Blue LED Slow blink AUX Mode Red LED Charging WARNING: The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. WARNINGTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. Attention should be drawn to environmental aspects of battery disposal. The product is designed to use in moderate climates Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling WARNINGchanges or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.