RE210 AC750 Wi-Fi Range Extender User Manual rev 2

 

RE210 AC750 Wi-Fi Range Extender REV1.0.2 1910011394 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Country Restriction Reason/remark Bulgaria None General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy None Luxembourg None If used outside of own premises, general authorization is required General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-lesund Russian Federation None Only for indoor applications Note: Please dont use the product outdoors in France. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)This device may not cause interference, and

(2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence dIndustrie Canada. Le fonctionnement est soumis aux deux conditions suivantes:

(1)cet appareil ne doit pas provoquer dinterfrences et

(2)cet appareil doit accepter toute interfrence, y compris celles susceptibles de provoquer un fonctionnement non souhait de lappareil. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numrique de la Classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. Korea Warning Statements

. NCC Notice & BSMI Notice 5.25GHz 5.35GHz 5.250~5.350GHz

,

. Safety Information When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Dont disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations. This product can be used in the following countries:

CZ GR NO UA AT ES LT RU BG FI LV SE BY FR MT SK CA GB NL TR DE HU PL US DK IE PT EE IT RO TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment:

Product Description: AC750 Wi-Fi Range Extender Model No.: RE210 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents EN 300 328 V1.8.1 EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1 EN 55022: 2010 + AC: 2011 EN 55024: 2010 EN 61000-3-2: 2006 + A1: 2009 + A2: 2009 EN 61000-3-3: 2013 EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 EN 50385: 2002 EN 301 893 V1.7.1 The product carries the CE Mark:

Person responsible for making this declaration:

Yang Hongliang Product Manager of International Business Date of issue: 2015 TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China CONTENTS Package Contents .................................................................................................... 1 Chapter 1 Introduction ........................................................................................... 2 1.1 Product Overview ............................................................................................ 2 1.2 Main Features ................................................................................................. 2 1.3 Appearance ..................................................................................................... 2 Chapter 2 Hardware Installation ........................................................................... 4 2.1 Before You Begin ............................................................................................ 4 2.2 Basic Requirements ........................................................................................ 4 2.3 Connecting the Device .................................................................................... 5 Chapter 3 Quick Installation Guide ....................................................................... 6 Chapter 4 Configure the Device .......................................................................... 11 4.1 Status ............................................................................................................ 11 4.2 Quick Setup ................................................................................................... 13 4.3 Network ......................................................................................................... 13 4.3.1 LAN .................................................................................................................. 14 4.3.2 DHCP Settings ................................................................................................. 15 4.3.3 DHCP Client List .............................................................................................. 17 4.4 Wireless ........................................................................................................ 17 4.4.1 Connect To Existing Network .......................................................................... 17 4.4.2 Extender Settings ............................................................................................ 18 4.4.3 MAC Filtering ................................................................................................... 18 4.4.4 Advanced Settings ........................................................................................... 20 4.4.5 High Speed ...................................................................................................... 21 4.4.6 Wireless Statistics............................................................................................ 21 4.5 LED On/Off .................................................................................................... 22 4.6 System Tools ................................................................................................. 23 4.6.1 Firmware Upgrade ........................................................................................... 23 4.6.2 Factory Defaults............................................................................................... 24 4.6.3 Backup & Restore ............................................................................................ 24 4.6.4 Reboot ............................................................................................................. 25 4.6.5 Password ......................................................................................................... 26 4.6.6 System Log ...................................................................................................... 26 Appendix A: Factory Defaults ............................................................................... 28 Appendix B: Troubleshooting ............................................................................... 29 Appendix C: Specifications ................................................................................... 31 Appendix D: Glossary ............................................................................................ 32 RE210 AC750 Wi-Fi Range Extender User Guide Package Contents The following items should be found in your package:

RE210 AC750 Wi-Fi Range Extender Ethernet Cable Quick Installation Guide Note:

Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact your distributor. Conventions The Range Extender, the Device or RE210 mentioned in this User guide stands for RE210 AC750 Wi-Fi Range Extender without any explanations. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand. The power plug may differ from the picture illustrated in this UG due to different regional power specifications. As follows we just take that of EU version for example. 1 RE210 AC750 Wi-Fi Range Extender User Guide Chapter 1 Introduction 1.1 Product Overview The RE210 AC750 Wi-Fi Range Extender is dedicated to Small Office/Home Office (SOHO) wireless network solutions. It will enlarge your existing wireless network and mobility within your wireless network while also allowing you to connect a wired device to a wireless environment. Increased mobility and the absence of cabling will be beneficial for your network. With using IEEE 802.11ac wireless technology, this device can transmit wireless data at the rate of up to 300Mbps (2.4GHz) + 433Mbps (5GHz). With multiple protection measures, including wireless LAN 64/128/152-bit WEP encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), the RE210 AC750 Wi-Fi Range Extender delivers complete data privacy. It is also compatible with all IEEE 802.11n, IEEE 802.11a, IEEE 802.11b and IEEE 802.11g products. It supports an easy wireless connection to the root Router/AP (equipped with WPS/QSS button) by pressing the RE button on the side panel. It also supports an easy, web-based setup for installation and management. Even though you may not be familiar with the Range Extender, you can easily configure it with the help of this Guide. Before installing the Range Extender, please look through this Guide to get the full information of the RE210 AC750 Wi-Fi Range Extender. Main Features 1.2 Complies with IEEE 802.11ac Provides multiple encryption security Types WPA-PSK/WPA2-PSK including: 64/128/152-bit WEP and Supports Built-in DHCP server Supports Firmware Upgrade Supports Web-based Management 1.3 Appearance Figure 1-1 2 RE210 AC750 Wi-Fi Range Extender User Guide LED Explanation:

Name Status Indication Flashing green WPS connection in progress. It may take up to 2 minutes. Solid green Solid orange Solid red Off On Off On Off On Off Flashing On Off WPS 2.4G 5G Power Ethernet The Range Extender has established a secure connection, and the signal strength is adequate. The Range Extender has established a secure connection, but the signal strength is too strong. The Range Extender has established a secure connection, but the signal strength is too weak. No active connection. The Range Extender is connected to the 2.4G wireless network of your main Router/AP. The Range Extender isnt connected to your main Router/AP. The Range Extender is connected to the 5G wireless network of your main Router/AP. The Range Extender isnt connected to your main Router/AP. The Range Extender is on. The Range Extender is off. The Range Extender is initializing. A device is connected to the ETHERNET port. No device is connected to the ETHERNET port. Table 1-1 RE: If your Wireless router or AP supports WPS or QSS function, you can press the WPS or QSS button and then press the RE button to establish a secure connection between the Wireless router or AP and the Range Extender RE210. Power: The switch for the power. Reset: This button is used to restore the Range Extenders factory default settings. There are two ways to reset the Range Extenders factory defaults:

Method One: With the Range Extender powered on, press and hold the Reset button (about 6 seconds) until all the LEDs turn on momentarily, then release the button and wait the Range Extender to reboot to its factory default settings. Method Two: Restore the default settings from System Tools > Factory Defaults of the Range Extender's Web-based Management page. LED: LED light switch. Ethernet: One 10/100/1000Mbps RJ45 Ethernet port used to add wireless connectivity to an Ethernet-enabled device such as Internet TV, DVR, Gaming console and so on. Please note that this port is not allowed to be connected with router or AP. 3 RE210 AC750 Wi-Fi Range Extender User Guide Chapter 2 Hardware Installation 2.1 Before You Begin Please read this User Guide carefully before installing and using the equipment. The operating distance range of your wireless connection can vary significantly depending on the physical position of the wireless devices. Factors that can weaken signals by getting in the way of your networks radio waves are metal appliances or obstructions, and walls. Typical ranges vary based on the types of materials and background RF (radio frequency) noise in your home or office. In order to optimize the performance of RE210, please follow the instructions below to achieve an ideal location (please make sure it is always within the wireless coverage of the wireless router). Half-way Between - Generally, the ideal location for RE210 is half-way between the 1) Wireless router and Wireless Client. If the wireless signal is not satisfactory, you may place RE210 somewhat nearer to the Wireless router. 2) 3) No Obstacles and Spacious - Clear obstacles in the way between RE210 and Wireless router. Its better to locate it in a spacious place, such as near the corridors. No Interference - Keep RE210 far away from wireless interference, which may come from electrical appliances that works in the same frequency band as RE210, such as Blue tooth devices, cordless phones, microwave ovens, etc. Note:

TP-LINK recommends that you connect to the Range Extender when your home network connection is poor, or when you want a larger wireless coverage to eliminate dead zones. As in compliance with the wireless transmission protocol, all the Range Extender devices are set to work in half-duplex instead of full-duplex mode. In other words, the Range Extender has to process one-way communication between your root Wireless Router or AP and the terminal clients; so the transmission time will be double-increased, while the speed will be decreased. 2.2 Basic Requirements Place your Range Extender in a well-ventilated place far from direct sunlight, any heater or heating vent. Leave at least 2 inches (5cm) space around the device for heat dissipation. Turn off your Range Extender and unplug the power adapter in a lighting storm to avoid damage. 4 RE210 AC750 Wi-Fi Range Extender User Guide Use Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0 or above. Operating temperature of the Range Extender should be 0~40 (32~104). Operating humidity of the Range Extender should be 10%~90%RH (Non-condensing). 2.3 Connecting the Device Figure 2-1 Typical connection of RE210 To establish a typical connection of the Range Extender, please take the following steps:

1. Connect the Cable/DSL modem to a Wireless router with an Ethernet cable. 2. Plug your RE210 directly to a standard electrical wall socket, which is near the Wireless router. 3. Connect your Wireless Clients (such as notebook, pad, smart phone, etc.) to RE210 wirelessly. Or you can connect your PC to the sole LAN port of Range Extender via an Ethernet cable. 4. Log in the web-based management page of RE210 and complete the configurations.

(Please refer to Chapter 3 Quick Installation Guide or Chapter 4 Configure the Device for the configurations, as you need.) Through the web page configuration you can successfully connect RE210 to the wireless router. 5. Adjust an ideal location for RE210. (Please refer to Section 2.1 Before You Begin for detailed information about ideal location.) 5 RE210 AC750 Wi-Fi Range Extender User Guide Chapter 3 Quick Installation Guide This chapter will guide you to configure your PC to communicate with the Range Extender and to configure and manage the RE210 AC750 Wi-Fi Range Extender easily with a Web-based utility. With a Web-based utility, it is easy to configure and manage the RE210 AC750 Wi-Fi Range Extender. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 1. To access the configuration utility, open a web-browser and type in the domain name http://tplinkrepeater.net in the address field of the browser. Figure 3-1 Login to the Range Extender After a moment, a login window will appear as shown in Figure 3-2. Enter admin for the User Name and Password (both in lower case letters). Then click OK or press Enter. Figure 3-2 Login Windows Note:

If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 6 RE210 AC750 Wi-Fi Range Extender User Guide 2. After successful login, there will pop up the Quick Setup Wizard page. Click Next to get the quick setup started. Figure 3-3 Quick Setup Start Note:

If you want to go through the Quick Setup right away, you can click Exit and enter the main menu of the device. 3. Click Next to continue. 4. The device will detect the existing 2.4GHz network. Please wait for a while. Figure 3-4 Quick Setup-Region Figure 3-5 Quick Setup Detect Existing Network 7 RE210 AC750 Wi-Fi Range Extender User Guide 5. A list of available 2.4GHz wireless network will appear. Check the box before the SSID of your desired network, and then click Next. Figure 3-6 Quick Setup Available Wireless Networks Note:

1. If you could not find your wireless network name (SSID) in the list, you can click Rescan to redetect it or tick the checkbox before "Set SSID and MAC Manually" to manually configure the wireless settings. If you dont want to use the 2.4GHz band, you can check the box of Skip at the bottom of the page. 2. 6. Wireless Settings page will appear as shown in Figure 3-7. Enter the WiFi Password of your main Router/AP, name your range extender WiFi network or keep it default, and then click Next to continue. Figure 3-7 Quick Setup Wireless Settings 8 RE210 AC750 Wi-Fi Range Extender User Guide 7. A list of available 5GHz wireless network will appear. Check the box before the SSID of your desired network, and then click Next. Figure 3-8 Quick Setup Available Wireless Networks Note:

1. If you could not find your wireless network name (SSID) in the list, you can click Rescan to redetect it or tick the checkbox before "Set SSID and MAC Manually" to manually configure the wireless settings. If you dont want to use the 5GHz band, you can check the box of Skip at the bottom of the page. 2. 8. Wireless Settings page will appear as shown in Figure 3-9. Enter the WiFi Password of your main Router/AP, name your range extender WiFi network or keep it default, and then click Next to continue. Figure 3-9 Quick Setup Wireless Settings 9 RE210 AC750 Wi-Fi Range Extender User Guide 9. Double-check your wireless setting and network setting, when Figure 3-10 appears. If verified, click Finish to complete the Quick Setup. If there is anything wrong, click Back to return to the previous pages and reconfigure it. Figure 3-10 Quick Setup Review Settings Note:

Its recommended to click the Export Settings button to save these settings as a txt file for your future reference. 10. When the Range Extender is restarting (as shown in Figure 3-11), please wait for a while patiently until the root devices wireless signal has been successfully extended. Figure 3-11 Quick Setup Restarting 10 RE210 AC750 Wi-Fi Range Extender User Guide Chapter 4 Configure the Device This Chapter describes how to configure your Range Extender via the web-based management page. The RE210 AC750 Wi-Fi Range Extender is easy to configure and manage with the Web-based (Internet Explorer, Netscape Navigator, Firefox, Safari, Opera or Chrome) management page, which can be launched on any windows, Macintosh or UNIX OS with a web browser. After a successful login, you can configure and manage the device. There are six main menus on the leftmost column of the web-based management page: Status, Quick Setup Wizard, Network, Wireless, LED On/Off and System Tools. Submenus will be available after clicking one of the main menus. On the right of the web-based management page are the detailed explanations and instructions for the corresponding page. 4.1 Status Selecting Status will enable you to view the Range Extenders current status and configuration, all of which are read-only. 11 RE210 AC750 Wi-Fi Range Extender User Guide Figure 4-1 Status Firmware Version - This field displays the current firmware version of the Range Extender. Hardware Version - This field displays the current hardware version of the Range Extender. Connection Status to Existing Network (2.4GHz or 5GHz) - This part shows you the current information of the root wireless network which the device is connecting to. Main Router/AP WiFi Network Name (SSID) - It shows the name of the wireless network which your device is connecting to. Signal Strength - It shows the root wireless network's signal strength that the device has received. 12 RE210 AC750 Wi-Fi Range Extender User Guide Connection Status - It shows whether your device has been connected to a wireless network currently. "Connected" means the range extender have connected to a wireless network, while if it shows "disconnected", you can click "connect" to connect. Range Extender Status (2.4GHz or 5GHz) - These are the current wireless settings or information of the device. Range Extender WiFi Network Name (SSID) - The Device's wireless network name

(SSID) which your PC or other device can be connected to. Range Extender MAC Address - The physical address of the system, as seen from the Network -> LAN page. Channel - The current wireless channel in use. Channel Width - The bandwidth of the wireless channel. Wired - The following is the information of Wired LAN. You can configure them in the Network page. Range Extender MAC Address - The physical address of the system, as seen from the Network -> LAN page. Range Extender IP Address - The IP address of the wired LAN. Subnet Mask - The subnet mask associated with IP address. Traffic Statistics - The system traffic statistics. Received (Bytes) - Traffic that counted in bytes has been received from wireless. Received (Packets) - Traffic that counted in packets has been received from wireless. Sent (Bytes) - Traffic that counted in bytes has been sent out from wireless. Sent (Packets) - Traffic that counted in packets has been sent out from wireless. System Up Time - The length of the time since the device was last powered on or reset. Click the Refresh button to get the latest status and settings of the device. 4.2 Quick Setup Please refer to Chapter 3 Quick Installation Guide. 4.3 Network The Network option allows you to customize your local network manually by changing the default settings of the Range Extender. There are three submenus under the Network menu: LAN, DHCP Settings and DHCP Client List. Clicking one of them will enable you to configure the corresponding function. The detailed explanations for each submenu are provided below. Figure 4-2 Network Menu 13 RE210 AC750 Wi-Fi Range Extender User Guide 4.3.1 LAN Selecting Network > LAN will enable you to configure the IP parameters of Network on this page. Figure 4-3 LAN Dynamic IP Figure 4-4 LAN Static IP MAC Address - The physical address of the LAN port, as seen from the LAN. The value cannot be changed. Type - Several IP types are supported, including: (1) Dynamic IP; (2) Static IP, and they are explained below. Dynamic IP - In this type, if your range extender have connected to a router, your client will dynamically get a IP Address / Gateway from the router, otherwise the client will get a IP Address / Gateway in the same network as you set below. And this type is recommended. Static IP - In this type, you can configure IP Address / Gateway manually. IP Address - Enter the IP address of your Range Extender in dotted-decimal notation (factory default setting is 192.168.0.254). Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. Gateway - The gateway should be in the same subnet as your IP address. Note:

1. The IP parameters cannot be configured if you have chosen Dynamic IP. In this situation the device will automatically configure the IP parameters appropriate to your need. 14 RE210 AC750 Wi-Fi Range Extender User Guide 2. 3. If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values, otherwise may result in lower wireless network performance or even can't work. If you choose Static IP, the domain name log in function won't work, and you have to use the IP you set to log in the Range Extender's web based utility. 4.3.2 DHCP Settings DHCP stands for Dynamic Host Configuration Protocol. The DHCP Server will automatically assign dynamic IP addresses to the computers on the network. This protocol simplifies network management and allows new wireless devices to receive IP addresses automatically without the need to manually assign new IP addresses. Selecting Network > DHCP Settings will enable you to set up the Range Extender as a DHCP

(Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN. The DHCP Server can be configured on the page

(shown as Figure 4-6), only when youve set the Network LAN type as Static IP in Figure 4-3. Note:

The DHCP Settings function cannot be configured if you have chosen Dynamic IP (DHCP) in Network -> LAN, in which situation the device will help you configure the DHCP automatically as you need. The DHCP Settings page will appear as Figure 4-5. Figure 4-5 DHCP Settings Auto Figure 4-6 DHCP Settings On 15 RE210 AC750 Wi-Fi Range Extender User Guide Figure 4-7 DHCP Settings Off DHCP Server - Selecting the radio button before Auto/On/Off will disable/enable the DHCP server on your Range Extender. The default setting is Auto. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer. Start IP Address - This field specifies the first address in the IP Address pool. 192.168.0.100 is the default start IP address. End IP Address - This field specifies the last address in the IP Address pool. 192.168.0.199 is the default end IP address. Address Lease Time - Enter the amount of time for the PC to connect to the Range Extender with its current assigned dynamic IP address. The time is measured in minutes. After the time is up, the PC will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. Default Gateway (Optional) - Enter the IP address of the gateway for your LAN. The factory default setting is 192.168.0.254. Default Domain (Optional) - Enter the domain name of the your DHCP server. You can leave the field blank. Primary DNS (Optional) - Enter the DNS IP address provided by your ISP. Consult your ISP if you dont know the DNS value. The factory default setting is 0.0.0.0. Secondary DNS (Optional) - Enter the IP address of another DNS server if your ISP provides two DNS servers. The factory default setting is 0.0.0.0. Click Save to save the changes. Note:

To use the DHCP server function of the device, you should configure all computers in the LAN as

"Obtain an IP Address automatically" mode. This function will not take effect until the device reboots. 16 RE210 AC750 Wi-Fi Range Extender User Guide 4.3.3 DHCP Client List Selecting Network > DHCP Client List will enable you to view the Client Name, MAC Address, Assigned IP and Lease Time for each DHCP Client attached to the device (Figure 4-8). Figure 4-8 DHCP Clients List ID - Here displays the index of the DHCP client. Client Name - Here displays the name of the DHCP client. MAC Address - Here displays the MAC address of the DHCP client. Assigned IP - Here displays the IP address that the Range Extender has allocated to the DHCP client. Lease Time - Here displays the time of the DHCP client leased. Before the time is up, DHCP client will request to renew the lease automatically. You cannot change any of the values on this page. To update this page and to show the current attached devices, click on the Refresh button. 4.4 Wireless The Wireless option, improving functionality and performance for wireless network, can help you make the Range Extender an ideal solution for your wireless network. Here you can create a wireless local area network just through a few settings. Wireless Settings is used for the configuration of some basic parameters of the Range Extender. There are five submenus under the Wireless menu (shown in Figure 4-9): Connect To Existing Network, Extender Settings, MAC Filtering, Advanced Settings, High Speed and Wireless Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. Figure 4-9 Wireless menu 4.4.1 Connect To Existing Network Selecting Wireless > Connect To Existing Network will guide you to set the basic parameters to 17 get a connection to the internet (show in Figure 4-10). RE210 AC750 Wi-Fi Range Extender User Guide Figure 4-10 Connect to Existing Network Click the Next button to continue, for detailed steps, please refer to Chapter 3 Quick Installation Guide . Click the Exit button to quit. 4.4.2 Extender Settings Selecting Wireless > Extender Settings will enable you to configure the basic settings for your wireless network on the screen below (Figure 4-11) Figure 4-11 Extender Settings Region - Per FCC regulations, all Wi-Fi products marketed in the U.S. must be fixed to the U.S. region only. WiFi Network Name (2.4GHz or 5GHz)- The Range Extender's wireless network name

(SSID) which your PC or other device can be connected to. Channel - The current wireless channel in use. Click Save to save the changes. 18 RE210 AC750 Wi-Fi Range Extender User Guide 4.4.3 MAC Filtering Choose menu Wireless MAC Filtering, you can control the wireless access by configuring the Wireless MAC Filtering function, shown in Figure 4-12. Figure 4-12 Wireless MAC Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address - The wireless station's MAC address that you want to filter. Status - The status of this entry, either Enabled or Disabled. Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 4-13. Figure 4-13 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions:

1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC is any hexadecimal digit). For example:

is XX-XX-XX-XX-XX-XX

(X Address 00-0A-EB-B0-00-0B. 2. Give a simple description for the wireless station in the Description field. For example:

Wireless station A. 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to save this entry. To modify or delete an existing entry:

1. Click the Modify in the entry you want to modify. If you want to delete the entry, click the Delete. 2. Modify the information. 19 RE210 AC750 Wi-Fi Range Extender User Guide 3. Click the Save button. Click the Enable All button to make all entries enabled Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page. Click the Previous button to return to the previous page. For example: If you desire that the wireless station A with MAC address 00-0A-EB-B0-00-0B and the wireless station B with MAC address 00-0A-EB-00-07-5F are able to access the router, but all the other wireless stations cannot access the router, you can configure the Wireless MAC Address Filtering list by following these steps:

1. Click the Enable button to enable this function. 2. Select the radio button Allow the stations specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button. 1) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F in the MAC Address field. 2) Enter wireless station A/B in the Description field. 3) Select Enabled in the Status drop-down list. 4) Click the Save button. 5) Click the Back button. The filtering rules that configured should be similar to the following list:

4.4.4 Advanced Settings Selecting Wireless > Advanced Settings will allow you to do some advanced settings for the device in the following screen shown in Figure 4-14. 20 RE210 AC750 Wi-Fi Range Extender User Guide Figure 4-14 Extender Settings Beacon Interval - Specifies a value between 40-1000 milliseconds. The beacons are the packets sent by the device to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. RTS Threshold - Specifies the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the device will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346. Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance since excessive packets. 2346 is the default setting and is recommended. DTIM Interval - Determines the interval of the Delivery Traffic Indication Message (DTIM). You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. Enable WMM - WMM function can guarantee the packets with high- priority messages being transmitted preferentially. It is strongly recommended enabled. Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time. Enable AP Isolation - Isolates all connected wireless stations so that wireless stations cannot access each other through WLAN. 4.4.5 High Speed Selecting Wireless > High Speed allows you to configure the wireless mode for your device

(show in Figure 4-15). Figure 4-15 High Speed 21 Concurrent-Dual Band Range Extender Extends both 2.4GHz and 5GHz bands for the RE210 AC750 Wi-Fi Range Extender User Guide router. High Speed Mode Boost the WiFi speed but only one band could be extended. High Speed Mode 1 Connect to the router on 2.4GHz only and connect to the WiFi clients on 5GHz only;

High Speed Mode 2 Connect to the router on 5GHz only and Extend to the WiFi clients on 2.4GHz only. 4.4.6 Wireless Statistics Selecting Wireless > Wireless Statistics will allow you to see the wireless transmission information in the following screen shown in Figure 4-16. Figure 4-16 Wireless Statistics MAC Address - Shows the connected wireless station's MAC address. Current Status - The connected wireless station's running status, one of STA-AUTH /

STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN /

Disconnected. Received Packets - packets received by the station. Sent Packets - packets sent by the station. You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. Note:

This page will be refreshed automatically every 5 seconds. 4.5 LED On/Off The LED On/Off option will allow you to turn on or off the LED status of your Range Extender

(shown in Figure 4-17). 22 RE210 AC750 Wi-Fi Range Extender User Guide Figure 4-17 LED On/Off LED Status - Shows if the LED is On or Off. Change the LED Setting - Switch the LED On or Off. Note:

Switching the LED On or Off does not affect the extender's performance or function. 4.6 System Tools System Tools option helps you to optimize the configuration of your device. You can upgrade the Range Extender to the latest version of firmware as well as backup or restore the Range Extenders configuration files. Its suggested that you change the default password to a more secure one because it controls access to the devices web-based management page. Besides, you can find out what happened to the system in System Log. There are six submenus under the System Tools menu (shown as Figure 4-18): Firmware Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, and System Log. Clicking any of them will enable you to configure the corresponding function. The detailed explanations for each submenu are provided below. Figure 4-18 The System Tools menu 4.6.1 Firmware Upgrade Selecting System Tools > Firmware Upgrade allows you to upgrade the latest version of firmware for the device on the screen shown in Figure 4-19. 23 RE210 AC750 Wi-Fi Range Extender User Guide Figure 4-19 Firmware Upgrade New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. Firmware Version - Here displays the current firmware version. Hardware Version - Here displays the current hardware version. The hardware version of the upgrade file must accord with the current hardware version. Note:

1. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the device itself, you can try to upgrade the firmware. 2. Before upgrading the devices firmware, you should write down some of your customized settings to avoid losing important configuration settings of device. To upgrade the device's firmware, follow these instructions:

file 1. Download a more firmware upgrade recent

(http://www.tp-link.com). from the TP-LINK website 2. Enter the path name or click Browse to select the downloaded file on the computer into the File blank. 3. Click Upgrade. Note:

Do not turn off the device or press the Reset button while the firmware is being upgraded. The device will reboot after the Upgrading has been finished. 4.6.2 Factory Defaults Selecting System Tools > Factory Default allows you to restore the factory default settings for the device on the screen shown in Figure 4-20. Figure 4-20 Restore Factory Defaults 24 Click Restore to reset all configuration settings to their default values. RE210 AC750 Wi-Fi Range Extender User Guide Default User Name: admin Default Password: admin Default IP Address: 192.168.0.254 Default Subnet Mask: 255.255.255.0 Note:

Any settings you have saved will be lost when the default settings are restored. 4.6.3 Backup & Restore Selecting System Tools > Backup & Restore allows you to save all configuration settings to your local computer as a file or restore the device's configuration on the screen shown in Figure 4-21. Figure 4-21 Save or Restore the Configuration Click Backup to save all configuration settings to your local computer as a file. To restore the device's configuration, follow these instructions:

Click Browse to find the configuration file which you want to restore. Click Restore to update the configuration with the file whose path is the one you have input or selected in the blank. Note:

The current configuration will be covered with the uploading configuration file. Wrong process will lead this device unmanaged. The restoring process lasts for 20 seconds and this device will restart automatically then. Keep the power of this device on during the process, in case of any damage. 4.6.4 Reboot Selecting System Tools > Reboot allows you to reboot the device on the screen shown in Figure 4-22. Figure 4-22 Reboot the device 25 RE210 AC750 Wi-Fi Range Extender User Guide Click the Reboot button to reboot the device. Some settings of the device will take effect only after rebooting, which include:

Change LAN IP Address (System will reboot automatically). Change the DHCP Settings. Change the Wireless configurations. Change the Web Management Port. Upgrade the firmware of the device (system will reboot automatically). Restore the device's settings to factory defaults (system will reboot automatically). Update the configuration with a file (system will reboot automatically). 4.6.5 Password Selecting System Tools > Password allows you to change the factory default user name and password of the device on the screen shown in Figure 4-23. Figure 4-23 Password It is strongly recommended that you change the factory default user name and password of the device. All users who try to access the device's web-based management page or Quick Setup will be prompted for the device's user name and password. Note:

The new user name and password must not exceed 14 characters in length and must not include any spaces. Enter the new Password twice to confirm it. Click Save when finished. Click Clear All to clear all. 4.6.6 System Log Selecting System Tools > System Log allows you to query the Logs of the device on the screen shown in Figure 4-24. 26 RE210 AC750 Wi-Fi Range Extender User Guide Figure 4-24 System Log The device can keep logs of all traffic. You can query the logs to find what happened to the device. Log Type - By selecting the log type, only logs of this type will be shown. Log Level - By selecting the log level, only logs of this level will be shown. Click the Refresh button to show the latest log list. Click the Save Log button to save all the logs in a txt file. Click the Mail Log button to send an email of current logs manually according to the address and validation information set in Mail Settings. The result will be shown in the later log soon. Click the Clear Log button to delete all the logs from the system permanently, not just from the page. Click the Next button to go to the next page, or click the Previous button return to the previous page. 27 RE210 AC750 Wi-Fi Range Extender User Guide Appendix A: Factory Defaults Item Common Default Settings Username Password IP Address Subnet Mask Domain Wireless SSID Default Value admin admin 192.168.0.254 255.255.255.0 http://tplinkrepeater.net TP-LINK_Extender_2.4GHz, TP-LINK_Extender_5GHz Wireless Security Wireless MAC Address Filtering Disabled Disabled 28 RE210 AC750 Wi-Fi Range Extender User Guide Appendix B: Troubleshooting T1. How do I restore my Range Extenders configuration to its factory default settings?

There are TWO methods available to restore the factory defaults. Method 1:

With the Range Extender powered on, press and hold the Reset button (about 6 seconds) until all the LEDs turn on momentarily, then release the button and wait the Range Extender to reboot to its factory default settings. Method 2:

Get logged in to the web-based management page of RE210, then go to System Tools ->

Factory Defaults and click Restore. Note:

Once the Range Extender is reset, the current configuration settings will be lost and you will need to reconfigure it. T2. What can I do if I forget my password?

1) Restore the Range Extenders configuration to its factory default settings. If you dont know how to do that, please refer to previous T1;

2) Use the default user name and password: admin, admin;

3) Try to reconfigure your Range Extender by following the instructions of this UG. T3. What can I do if I cannot access the web-based configuration page?

1) Check to verify all the connections (either wireless or wired ones) are proper. If yes, please proceed to the next step; otherwise, check the connections again. 29 RE210 AC750 Wi-Fi Range Extender User Guide 2) Try to obtain an IP address and gateway; if succeed, open your web-browser, enter the default domain http://tplinkrepeater.net in the address field and get logged in. If you are unable to log in, please Reset the device, and then use the default IP address to get into the web-based configuration page, reconfigure the device. 3) Feel free to contact our technical support, if the problem still persists. T4. How can I know that my wireless signal has been repeated and boosted by RE210?

An easy way is to compare the signal strength of your target wireless network (symbolized by its SSID), with RE210 in operation vs. out of operation. Before comparison, youd better make sure your computer can obtain an IP address from your target wireless network and thus access the Internet, either via RE210 or without. T5. Will the Range Extender work if I connect the Ethernet port of it to the router via Ethernet cable?

Sorry, it wont work. The Range Extender is designed to connect wirelessly to the router, while the Ethernet port is designed to connect with a wired device, like Internet TV, Gaming console, DVR and so on. T6. Why does the wireless transmission rate speed down, while the wireless signal is stronger after repeated by RE210?

In compliance with the wireless transmission protocol, all the Range Extender devices are set to work in half-duplex instead of full-duplex mode. In other words, the Range Extender has to process one-way communication between your root Wireless Router or AP and the terminal clients; so the transmission time will be double-increased, while the speed will be decreased. TP-LINK recommends that you connect to the Range Extender when your home network connection is poor, or when you want a larger wireless coverage to eliminate dead zones. 30 RE210 AC750 Wi-Fi Range Extender User Guide Appendix C: Specifications General Standards and Protocols IEEE 802.3, 802.3u, 802.11ac, 802.11n, 802.11b and 802.11g, TCP/IP, DHCP Safety & Emission CE Ports Wireless One 10/100/1000M Auto-Negotiation LAN RJ45 port Frequency Band 2.4GHz & 5GHz Radio Data Rate 5GHz up to 433Mbps 2.4GHz up to 300Mbps Frequency Expansion DSSS (Direct Sequence Spread Spectrum) Modulation Security Sensitivity @PER DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM WEP, WPA-PSK, WPA2-PSK 270M: -68dBm@10% PER 108M: -68dBm@10% PER;

54M: -68dBm@10% PER 11M: -85dBm@8% PER;

6M: -88dBm@10% PER 1M: -90dBm@8% PER Physical and Environment Working Temperature 0~40 (32~104) Working Humidity 10% ~ 90% RH, Non-condensing Storage Temperature

-40~70(-40~158) Storage Humidity 5% ~ 95% RH, Non-condensing 31 RE210 AC750 Wi-Fi Range Extender User Guide Appendix D: Glossary 802.11ac - IEEE 802.11ac is a wireless computer networking standard of 802.11.This specification will enable multi-station WLAN throughput of at least 1 gigabit per second .This is accomplished by extending the air interface concepts embraced by 802.11n: wider RF bandwidth, more MIMO spatial streams, multi-user MIMO, and high-density modulation (up to 256 QAM). 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium

(EWC) was formed to help accelerate the IEEE 802.11n development process and promote a technology specification for interoperability of next-generation wireless local area networking

(WLAN) products. 802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security. Access Point (Range Extender) - A wireless LAN transceiver or "base station" that can connect a wired LAN to one or many wireless devices. Access points can also bridge to each other. DNS (Domain Name System) An Internet Service that translates the names of websites into IP addresses. Domain Name - A descriptive name for an address or group of addresses on the Internet. DoS (Denial of Service) - A hacker attack designed to prevent your computer or network from operating or communicating. DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over existing traditional phone lines. ISP (Internet Service Provider) - A company that provides access to the Internet. MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be transmitted. SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. 32 RE210 AC750 Wi-Fi Range Extender User Guide Wi-Fi A trademark of the Wi-Fi Alliance and the brand name for products using the IEEE 802.11 family of standards. WLAN (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area. WPA (Wi-Fi Protected Access) - WPA is a security technology for wireless networks that improves on the authentication and encryption features of WEP (Wired Equivalent Privacy). In fact, WPA was developed by the networking industry in response to the shortcomings of WEP. One of the key technologies behind WPA is the Temporal Key Integrity Protocol (TKIP). TKIP addresses the encryption weaknesses of WEP. Another key component of WPA is built-in authentication that WEP does not offer. With this feature, WPA provides roughly comparable security to VPN tunneling with WEP, with the benefit of easier administration and use. This is similar to 802.1x support and requires a RADIUS server in order to implement. The Wi-Fi Alliance will call this, WPA-Enterprise. One variation of WPA is called WPA Pre Shared Key or WPA-Personal for short - this provides an authentication alternative to an expensive RADIUS server. WPA-Personal is a simplified but still powerful form of WPA most suitable for home Wi-Fi networking. To use WPA-Personal, a person sets a static key or "passphrase" as with WEP. But, using TKIP, WPA-Personal automatically changes the keys at a preset time interval, making it much more difficult for hackers to find and exploit them. The Wi-Fi Alliance will call this, WPA-Personal. 33