| submitted | available | document details (if available) | source link |
|---|---|---|---|
| July 12 2018 | October 12 2018 |
| various | User Manual | Users Manual | 2.43 MiB | July 12 2018 / October 12 2018 |
User Guide TL-WPA7510 AC750 Wi-Fi Range Extender, AV1000 Powerline Edition REV2.0.0 1910012399 Contents About This Guide 1 Chapter 1 Get to Know Your Powerline Extender 2 1. 1. Product Overview. 3 1. 2. Product Appearance. 3 1. 2. 1. LED Legend . 3 1. 2. 2. Physical Interface . 4 Chapter 2 Initial Use 6 2. 1. To Set Up a New Secure Wireless Network . 7 2. 2. To Extend the Existing Wireless Network . 8 Chapter 3 Configuring via Web Management Interface 11 3. 1. Management Interface. 12 3. 1. 1. Log In . 12 3. 1. 2. Change the Login Account . 12 3. 2. Manage Powerline Network . 13 3. 2. 1. Add a New Device to the Powerline Network . 13 3. 2. 2. Change Powerline Network Name. 14 3. 3. Wi-Fi Move . 14 3. 4. Wi-Fi Clone . 15 3. 5. Wireless Network. 16 3. 5. 1. Customize Wireless Settings . 16 3. 5. 2. Wireless Clients . 18 3. 6. LED Schedules . 19 3. 7. Schedule Your Wireless Function . 20 3. 8. Parental Controls . 22 3. 9. Guest Network. 24 3. 10. MAC Filter . 25 3. 11. Administration. 27 3. 11. 1. LAN IP Address. 27 3. 11. 2. Set Up System Time. 27 3. 11. 3. Upgrade the Firmware . 29 3. 11. 4. Backup and Restore Configuration Settings. 29 3. 11. 5. System Log . 31 About This Guide This guide is a complement to Quick Installation Guide. The Quick Installation Guide provides instructions for quick internet setup, while this guide contains details of each function and demonstrates how to configure them in typical scenarios. When using this guide, please notice that features of the powerline extender may vary slightly depending on the model and software version you have, and on your location and language. All images, parameters and descriptions documented in this guide are used for demonstration only. Conventions In this guide the following conventions are used:
Convention Description Powerline extender Stands for AV1000 Gigabit Powerline ac Wi-Fi Extender without any Teal_Underlined explanation. Hyperlinks are in teal and underlined. You can click to redirect to a website or a specific section. Key information appears in teal, including management page text such as menus, items, buttons and so on. The menu structures to show the path to load the corresponding page. For example, Wireless > MAC Filter means the MAC Filter function page is under the Wireless menu. Ignoring this type of note might result in a malfunction or damage to the device. Indicates important information that helps you make better use of your device. click to edit the corresponding entry. click to delete the corresponding entry. click to enable or disable the corresponding entry. Teal
>
Note:
Tips:
Symbols on the web page More Info The latest software, management app and utility are available from the Download Center at http://www.tp-link.com/support. The Quick Installation Guide (QIG) can be found where you find this guide or inside the package of the powerline extender. Specifications can be found on the product page at http://www.tp-link.com. A Technical Support Forum is provided for you to discuss our products at http://forum.tp-link.com. Our Technical Support contact information can be found at the Contact Technical Support page at http://www.tp-link.com/support. 1 Chapter 1 Get to Know Your Powerline Extender This chapter introduces what the powerline extender can do and describes its main features and appearance. It contains the following sections:
Product Overview Product Appearance Chapter 1 Get to Know Your Powerline Extender 1 1 Product Overview TP-Links Powerline Wi-Fi Extender is a combined wired/wireless network expansion device. With the help of your homes existing electrical circuitry, it can extend your Wi-Fi to wherever you want in your house. With Ethernet ports and built-in antennas, the powerline Wi-Fi extender provides wired and wireless access for multiple computers and mobile devices. With various features and functions, the powerline Wi-Fi extender is the perfect choice for your home or business network. 1 2 Product Appearance Your powerline extender may differ in appearance slightly from what is depicted because of the region and product version. 1 2 1 LED Legend LEDs indicate the powerline extenders working status. For more details, please refer to the following table. Name Power Powerline Ethernet Status On Off Flashing Yellow-
green Red Off On Off Indication Power is on. Power is off. Pairing is in progress. The powerline extender is connected to the powerline network and is in a suitable location. The powerline extender is experiencing poor signal strength. Try plugging it into another wall socket. The powerline extender powerline network. The LAN port is connected to a powered-on device. The LAN port is not connected to a powered-on device. is not connected to the 3 Chapter 1 Name Wireless 2.4GHz Wireless 5GHz Get to Know Your Powerline Extender Status On Off Flashing On Off Flashing Indication is cloning 2.4GHz The 2.4GHz wireless band is enabled. The 2.4GHz wireless band is disabled. Slowly: The powerline extender wireless network settings from the main router. Quickly: The powerline extender is syncing 2.4GHz wireless network settings from an existing powerline extender. The 5GHz wireless band is enabled. The 5GHz wireless band is disabled. Slowly: The powerline extender is cloning 5GHz wireless network settings from the main router. Quickly: The powerline extender is syncing 5GHz wireless network settings from an existing powerline extender. 1 2 2 Physical Interface Ethernet Port Reset Button Pair Button LED Button Wi-Fi Button Plug Ethernet Port Connect the Ethernet port to your wired device, such as a computer, a router or a game console, via an Ethernet cable. Reset Press and hold the Reset button for at least 2 seconds to reset the powerline extender 4 Chapter 1 Get to Know Your Powerline Extender to factory default settings. When Reset is triggered properly, all LEDs will turn off and start on again. Pair Button Press and hold the button for 1 second to join a powerline network. Go to To Set Up a New Secure Wireless Network for more information. LED Button Press and hold the button for 1 second to turn all LEDs on or off. All LEDs are on by default. If you dont feel like being bothered by the LED light at night, press and hold the button for 1 second to turn all LEDs off. The next morning, just press and hold the button again to turn them on. Wi-Fi Button Press and hold the button for 1 second to copy wireless settings from the main router to the extender. Go to Wi-Fi Clone for more information. Press and hold the button for at least 5 seconds to turn the wireless function on or off. The wireless function is on by default. Plug The powerline adapter has a Plug that can be connected to any standard power socket. Note:
1. The provided plug may differ from the picture due to different regional power specifications. 2. Use the product only in below directions. Or 3. Plug the product directly into a wall socket instead of a power strip. Wall Outlet Power Strip 5 Chapter 2 Initial Use This chapter guides you on how to use the powerline extender when you first open the package. It contains the following sections:
To Set Up a New Secure Wireless Network To Extend the Existing Wireless Network Chapter 2 2 1 I want to:
How can I do that?
To Set Up a New Secure Wireless Network Initial Use Use the Powerline Wi-Fi Kit to set up a new secure wireless network in my house. For example, I have a wireless router in my house, but the wireless signal cannot reach every corner. So I bought a Powerline Wi-Fi Kit to extend the wireless network. The Powerline Wi-Fi Kit includes a powerline adapter and a powerline extender. 1. Connect the powerline adapter to an available LAN port of 2. Plug the powerline adapter into a wall socket. 3. Plug the powerline extender into a wall socket near the the router. adapter. 1000Mbps Extender TL-WPA7510 Powerline Router WAN LAN 1000Mbps Adapter TL-PA7010
(For demonstration only) Ethernet Cable 4. Pair the powerline devices. a . Press the Pair button of the powerline adapter for 1 second. The Power LED starts blinking. Note: If the Power LED does not blink, press the button again. b . Within two minutes, press the Pair button of the powerline extender for 1 second. The Power LED starts blinking. When the Powerline LED turns solid on, the pairing process is done!
7 Chapter 2 Initial Use Blinking r i a P within 2 minutes 1000Mbps 1000Mbps Adatper TL-PA7010 Blinking t e s e R r i a P D E L i F
-
i W On Extender TL-WPA7510 5. Relocate the new extender to the Wi-Fi dead zone. Use the SSID (network name) and password on the provided Wi-Fi Info Card to connect to the internet. Note: A red Powerline LED indicates poor signal strength. Move the extender to another location. Done!
2 2 I want to:
Now enjoy the internet with the SSID and password printed on the Wi-Fi Info Card!
To Extend the Existing Wireless Network Extend the existing wireless network by adding a new powerline extender into the existing powerline network. For example, I already set up a wireless network using powerline devices, but the wireless network is still not big enough to reach 8 Chapter 2 How can I do that?
Initial Use the top floor. So I bought a new powerline extender to extend the wireless network. 1. Plug the new powerline extender into a wall socket near one of the existing powerline extender. Powerline 1000Mbps New Powerline Extender TL-WPA7510 1000Mbps Existing Powerline Device
(For demonstration only)
. Is it on?
2. Check the new extenders Powerline LED If it is on, follow Step 4 > A. If it is off, follow Step 3 and Step 4 > B. 3. Join the new powerline extender into the existing powerline network by pairing two powerline devices. a . Press the Pair button on the existing powerline device for 1 second. The Power LED starts blinking. Note: If the Power LED does not blink, press the button again. b . Within two minutes, press the Pair button on the new powerline extender for 1 second. The Power LED starts blinking. When the Powerline LED turns solid on, the pairing process is complete. Blinking t e s e R r i a P D E L i F
-
i W within 2 minutes Blinking t e s e R r i a P D E L i F
-
i W On 1000Mbps Existing Powerline Device 1000Mbps New Powerline Extender TL-WPA7510 4. Relocate the new extender to the Wi-Fi dead zone. Note: A red Powerline LED indicates poor signal strength. Move the extender to another location. 9 Chapter 2 Initial Use A . Use the default SSID (network name) and password on the provided Wi-Fi Info Card to connect to the internet. B . If you cannot find the default SSID in your Wi-Fi network list, this may mean the Wi-Fi Move feature has automatically copied over the existing wireless settings. In this case, use the SSID and password of your existing powerline network to connect. Done!
Enjoy the internet through your extended network!
10 Chapter 3 Configuring via Web Management Interface The powerline extender has a management interface to configure all settings. The management interface can be opened on any device that has a web browser, such as Internet Explorer, Chrome or Firefox. This chapter is going to give detailed information on what functions the powerline extender has and how to configure them. It contains the following sections:
Management Interface Manage Powerline Network Wi-Fi Move Wi-Fi Clone Wireless Network LED Schedules Schedule Your Wireless Function Parental Controls Guest Network MAC Filter Administration Chapter 3 Configuring via Web Management Interface Log In 3 1 Management Interface 3 1 1 There are two methods to log in to the management interface. Method 1: Via web browser Follow the steps below:
1. Connect your device to the powerline extender wirelessly. 2. Launch a web browser and type in http://tplinkplc.net to open the management interface. 3. Enter admin (the default username and password) for both username and password. We recommend you change them immediately after your first login. 4. Click Login. Method 2: Via tpPLC Utility Follow the steps below:
1. Connect your computer to the powerline extender via an Ethernet cable or wirelessly. 2. Obtain and install the tpPLC Utility from the products Support page at http://www. 3. Open the utility, move your mouse over your powerline extender, and click the tp-link.com. icon that appears beside it. 4. Enter admin for both username and password. 5. Click Login. 3 1 2 Change the Login Account We strongly recommend you change the login account immediately after the first login. Follow the steps below to change the account. 1. Go to System Tools > Administration. 12 Chapter 3 Configuring via Web Management Interface 2. Follow instructions on the page to set a new username and password. A strong password should be at least 8 characters in length, combining uppercase and lowercase letters, numbers and punctuations. 3. Click Save to make the settings effective. 3 2 Manage Powerline Network A powerline network is formed of powerline devices, including adapters and extenders. Powerline devices in the same powerline network share the same powerline network name. 3 2 1 Add a New Device to the Powerline Network 1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to the Status page. Click the Powerline Network icon to see the Powerline Device List. 13 Chapter 3 Configuring via Web Management Interface 3. Click the add icon and enter the Powerline Key of the device you want to add. The Powerline Key contains 16 capital letters, formed like XXXX-XXXX-XXXX-XXXX. It is printed on the back of the powerline device. 4. Click Add to add the device. 3 2 2 Change Powerline Network Name You can change the extenders powerline network name to add it to or remove it from a powerline network. Follow the steps below to change the name. 1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to Device Settings > Powerline. 3. Change the Network Name. You can also click Default to use the default network name, e.g. HomePlugAV. However, if the default name is used, the Wi-Fi Move function will be automatically disabled. 4. Click Save to make the settings effective. 3 3 Wi-Fi Move Wi-Fi Move is enabled by default. With the feature enabled, any changes made to the settings of one powerline extender will be automatically synchronized to other powerline extenders whose Wi-Fi Move feature is also enabled on the same powerline network . 14 Chapter 3 Configuring via Web Management Interface Settings will be synced include: Wireless SSID & Password, Wireless Security, Wireless Mode, Wi-Fi Schedules, LED Schedules, Wi-Fi Clone Settings, MAC Filter Settings, Parental Controls, and Guest Network. Follow the steps below to enable the Wi-Fi Move feature:
1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to Wireless > Wi-Fi Move. 3. Toggle On to enable the feature. 3 4 Wi-Fi Clone I want to:
How can I do that?
Copy wireless settings from my router to my extender, so I can use the same SSID and password to access the internet in my house. 1 Connect to the powerline extender wirelessly. Visit http://
tplinkplc.net, and log in with the username and password you set for the extender. 2 Go to Wireless > Wi-Fi Clone. 3 Select a Wi-Fi band or both to be cloned. 2.4GHz & 5GHz is selected by default. 4 Before cloning, make sure your router supports the same band as your extender. If you do not know how to check this, go to your routers User Guide for more information. 5 Plug your extender near your router. 6 Press the WPS button on your router. 15 Chapter 3 Configuring via Web Management Interface WPS WAN WPS LAN Wireless Router 7 Within two minutes, press the Wi-Fi button on the side panel of the extender. The 2.4GHz and 5GHz LEDs start blinking. t e s e R r i a P D E L i F
-
i W 1000Mbps Done!
When the corresponding Wi-Fi LED blinks quickly for 3 seconds and then stays on. Its done!
3 5 Wireless Network 3 5 1 Customize Wireless Settings The powerline extenders wireless network name (SSID) and password, and security option are preset in the factory. The preset SSID and password can be found on the product label and Wi-Fi Info Card. You can customize the wireless settings according to your needs. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. Go to Wireless > Settings page. To enable or disable the wireless function:
Select the box to enable the wireless Radio of 2.4GHz or 5GHz. Deselect the box to disable wireless function. If disabled, all wireless settings will be ineffective. 16 Chapter 3 Configuring via Web Management Interface To change the wireless network name (SSID) and wireless password:
The default SSID is TP-Link_XXXX for 2.4GHz network and TP-Link_XXXX_5G for 5GHz network, and the default password is printed on the Wi-Fi Info Card and the product lable. You can change the default ones by directly entering new ones in the field. SSID is up to 32 characters, and the value in both SSID and password is case-sensitive. Note:
Remember to write down the new SSID and password, for you may be disconnected when new settings are effective. To hide SSID:
Select Hide SSID, and your SSID will not be broadcasted. It wont display when you scan for local wireless network list on your wireless device and you need to manually join the network. To have more advanced settings Click Advanced to have more advanced settings about password. 17 Chapter 3 Configuring via Web Management Interface Security: Select an option from the Security drop-down list. The extender provides three options, No Security, WPA/WPA2 Personal (Recommended), and WEP. WPA2 uses the newest standard and the security level is the highest. We dont recommend you to change the default settings unless necessary. Mode: Select the desired mode. 802.11n only: Select only if all of your wireless clients are 802.11n devices. 802.11g/n mixed: Select if you are using both 802.11g and 802.11n wireless clients. 802.11b/g/n mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Note: When 802.11n only mode is selected, only 802.11n wireless clients can connect to the extender. It is strongly recommended that you select 802.11b/g/n mixed, and all of 802.11b, 802.11g, and 802.11n wireless clients can connect to the extender. 802.11ac only (5GHz): Select only if all of your wireless clients are 802.11ac devices. 802.11n/ac mixed (5Ghz): Select if you are using both 802.11n and 802.11ac wireless clients. 802.11a/n/ac mixed (5Ghz): Select if you are using a mix of 802.11ac, 802.11n and 802.11ac wireless clients. It is strongly recommended that you select 11a/n/ac mixed. Channel Width: Select the channel width. The default setting is Auto, which can adjust the channel width for your clients automatically. Channel: Select the channel you want to use from the drop-down list. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. Transmit Power: Select the level of transmit power. We recommend you choose High to have the best signal strength. 3 5 2 Wireless Clients Follow the steps below to view detailed information of all wireless clients connected to the extender. 1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to Wireless > Clients page. 18 Chapter 3 Configuring via Web Management Interface 3. Now you can view the detailed information, including device name, IP address, MAC address, connected wireless band as well as security option. Tip: You can also see the wireless details by clicking the wireless clients icon on Status> Wireless Clients. 3 6 I want to:
LED Schedules Automatically turn off LEDs at times when I do not want light in my room. For example, I want to turn LEDs off everyday from 00:00am to 7:00am. 1 Connect to the powerline extender wirelessly. Visit http://
tplinkplc.net and log in with the username and password you set. How can I do that?
2 Go to Device Settings > LED Schedules. 3 Toggle On to enable the LED Scheduler. Note: Please make sure that the system time is correct before using this function. 4 Click Add to add an entry. 5 Choose LED Off Time from 00:00 to 7:00, and then check all boxes from Sunday to Saturday. 6 Click Enable this entry to make it effective. 19 Chapter 3 Configuring via Web Management Interface Done!
7 Click OK to save the settings. Now your LEDs will be turned off automatically at 00:00 and turned on at 7:00am the next morning. 3 7 Schedule Your Wireless Function I want to:
Automatically turn off my wireless network at times when I do not need the wireless connection. For example, I want to turn them off from 00:00am to 7:00am. Yet if I have my wireless devices connected to the extender at that time, I want the wireless on till all devices are disconnected from the internet. 1 Connect to the powerline extender wirelessly. Visit http://
tplinkplc.net and log in with the username and password you set. 2 Go to Wireless > Wi-Fi Schedules. Note: Please make sure that the system time is correct before using this function. How can I do that?
20 Chapter 3 Configuring via Web Management Interface 3 Toggle On to enable the Wi-Fi Scheduler. If you are prompted like the following picture, click Continue. 4 Check the box of Do not turn off Wi-Fi while clients are connected to it and click Save. 5 Click Add to add an entry. 6 Choose 00:00 and 7:00 from the drop-down list. Check all boxes from Sunday to Saturday. 7 Click Enable this entry to make it effective. 21 Chapter 3 Configuring via Web Management Interface 8 Click OK to save the settings. Now your Wi-Fi will be automatically turned off at 00:00 and turned on at 7:00am the next morning. Done!
Note:
The Wi-Fi LED will turn off if the wireless network is disabled. 3 8 Parental Controls I want to:
Control when my childrens wireless devices can access the internet. For example, I want to allow my childrens wireless devices to access only from 18:00 (6PM) to 22:00 (10PM) on weekdays and not other times. 1 Connect to the powerline extender wirelessly. Visit http://
tplinkplc.net, and log in with the username and password you set for the extender. 2 Go to Parental Controls. How can I do that?
22 Chapter 3 Configuring via Web Management Interface 3 Toggle On to enable Parental Controls. If you are prompted like the following picture, click Continue. 4 Click Add. 5 Click View Existing Devices, and select the device to be controlled. Or, enter the MAC Address manually. icon to set the Internet Access Time. Drag the cursor over the appropriate cell(s) and click Save. Note: Please make sure that the system time is correct before using this function. 6 Click the 7 Enter a Description for the entry. 8 Click Enable this entry to make it effective. 23 Chapter 3 Configuring via Web Management Interface 9 Click OK to save the settings. Done!
Now the controlled device can access only from 18:00 (6PM) to 22:00 (10PM) on weekdays and not other times. 3 9 Guest Network I want to:
How can I do that?
Create a network for my guests, providing internet access for them while at the same time limit the network authorities for guests to ensure network security and privacy. 1 Connect to the powerline extender wirelessly. Visit http://
tplinkplc.net, and log in with the password you set for the extender. 2 Go to Guest Network. 3 Check the box of relative entry to limit network authorities. If you have problems understanding these items, click the question mark on the upper right corner to have more information. 4 Click Save to make the settings effective. 24 Chapter 3 Configuring via Web Management Interface 5 Click 2.4GHz or 5GHz to choose a wireless band, and configure the following settings. To enable or disable the guest network function:
Select the box to enable the guest network function. Deselect the box to disable guest network function. If disabled, all guest network settings of the corresponding band will be ineffective. To change the guest network name (SSID) and password:
The default SSID is TP-Link_Guest_XXXX for 2.4GHz guest network and TP-Link_Guest_XXXX_5G for 5GHz guest network. The default password is the same as the host networks, which is printed on the Wi-Fi Info Card. You can change the default ones by directly entering new ones in the field. SSID is up to 32 characters, and the value in both SSID and password is case-
sensitive. Now you can tell your guests to connect to the guest network you created. Done!
3 10 MAC Filter This function exploits the uniqueness of the MAC (Medium Access Control) address, a unique 12-digit hexadecimal address (for example, D8-5D-4C-B4-46-EA) of every network device, to determine if the device can or cannot access your wireless network. I want to:
Prevent unauthorized users from accessing my wireless network by utilizing the network devices MAC address. For example, I have a computer that is connected to my wireless network. Now, an unknown device (an intruder) is also using my wireless network, which affects my internet speed. I would like to control my wireless network with the following capabilities:
My computer is always allowed to access the wireless network. 25 Chapter 3 Configuring via Web Management Interface How can I do that?
The unknown device is not allowed to access the wireless network. I dont have to keep changing my wireless password as often. 1 Connect to the powerline extender wirelessly. Visit http://
tplinkplc.net, and log in with the username and password you set for the extender. 2 Go to Wireless> MAC Filter. 3 Toggle On to enable MAC Filter. 4 Select either of the filtering rules and click Save. Here we select Block wireless access from the devices in the list below and then click Save. 5 Click Add under Device List to add devices to the list. 6 Click View Devices to see how many devices are now connected to the network. Click Choose to choose a device. You can also enter the MAC Address manually. 7 Give a description of the entry in the Description field.
(Optional) 26 Chapter 3 Configuring via Web Management Interface 8 Click Enable this entry to make this entry effective. 9 Click OK to save the settings. Now MAC Filter is implemented to protect your wireless network. Done!
3 11 Administration 3 11 1 LAN IP Address Follow the steps below to configure LAN settings of the extender. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. Go to Device Settings > LAN Settings. LAN Type: Select Dynamic IP to have your extender automatically obtain IP Address from the main router. Select Static IP to manually configure the LAN parameters. IP Address: The IP address of the powerline extender. Subnet Mask: The subnet mask associated with IP address. Default Gateway: The IP address of the gateway device. 3 11 2 Set Up System Time System time is the time displayed while the extender is running. The system time you configure here will be used for other time-based functions like Parental Controls, Wi-Fi Schedules. You can manually set how to get the system time. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. Go to System Tools > Time Settings page. 27 Chapter 3 Configuring via Web Management Interface To automatically synchronize the time:
1. Select your local Time Zone from the drop-down menu. 2. In the NTP Server I field, enter the IP address or domain name of your desired NTP 3. In the NTP Server II field, enter the IP address or domain name of the second NTP Server. (Optional) Server. (Optional) 4. Click Get GMT and click Save. To manually set the date and time:
1. In the Time Settings field, select your local Time Zone. 2. Enter the current Date. 3. Set the current Time (In 24-hour clock format, e.g. 16:00:00 is 04:00PM). 4. Click Save. To set up Daylight Saving time:
1. Select Enable Daylight Saving. 2. Select the correct Start date and time when daylight saving time starts at your local time zone. 28 Chapter 3 Configuring via Web Management Interface 3. Select the correct End date and time when daylight saving time ends at your local time zone. 4. Click Save. 3 11 3 Upgrade the Firmware TP-Link is dedicated to improving and richening the product features, giving you a better network experience. We will release the latest firmware at TP-Link official website, you can download the latest firmware file from our website: www.tp-link.com and upgrade the firmware to the latest version. 1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to System Tools > Firmware Upgrade page and confirm the Hardware Version. 3. Go to www.tp-link.com. Download the latest firmware file for the extender. Note: The upgraded firmware version must correspond to the hardware. 4. Click Browse to locate the downloaded new firmware file, and click Upgrade. 5. Wait a few minutes for the upgrading and rebooting. Note:
1. Before upgrading the firmware, its better to back up your current settings. 2. During the upgrading process, do not turn off or reset the extender. 3 11 4 Backup and Restore Configuration Settings The configuration settings are stored as a configuration file in the extender. You can back up the configuration file to your computer for future use and restore the extender to a previous settings from the backup file when needed. Moreover, if needed, you can erase the current settings and reset the extender to the default factory settings. To backup configuration settings:
1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to System Tools > Backup & Restore page. 29 Chapter 3 Configuring via Web Management Interface 3. Click Backup to save a copy of the current settings to your local computer. A config. bin file will be stored to your computer. To restore configuration settings:
1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to System Tools > Backup & Restore page. 3. Click Browse to locate the backup configuration file stored on your computer, and click Restore. The configuration file is config.bin. 4. Wait a few minutes for the restoring and rebooting. Note: During the restoring process, do not turn off or reset the extender. To reset the extender to factory default settings:
1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to System Tools > Backup & Restore page. 3. Click Factory Restore to reset the extender. 4. Wait a few minutes for the resetting and rebooting. Note:
1. During the resetting process, do not turn off the extender. 2. We strongly recommend you back up the current configuration settings before resetting the extender. 30 Chapter 3 Configuring via Web Management Interface 3 11 5 System Log When the extender does not work properly, you can save the system log and send it to the technical support for troubleshooting. Follow the steps below to save the system log:
1. Connect to the powerline extender wirelessly. Visit http://tplinkplc.net, and log in with the username and password you set for the extender. 2. Go to System Tools > System Log. 3. Choose the type and level of the system log according to your need. 4. Click Save Log to save the system log to local. 31 COPYRIGHT & TRADEMARKS is a registered Specifications are subject to change without notice. trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. Copyright 2018 TP-Link Technologies Co., Ltd. All rights reserved. 32 FCC compliance information statement Product Name: AC750 Wi-Fi Range Extender, AV1000 Powerline Edition Model Number: TL-WPA7510 Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: http://www.tp-link.com/us/
Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 ) This device may not cause harmful interference. 2 ) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. 33 FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter. We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2018.4.4 34 CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY(the maximum transmitted power) 2400 MHz -2483.5 MHz(20dBm) 5150 MHz -5250 MHz(23dBm) EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce RF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. Restricted to indoor use. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. lappareil ne doit pas produire de brouillage;
2. lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. Caution:
The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. 35 The high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
En outre, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration dexposition aux radiations:
Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Industry Canada Statement CAN ICES-3 (B)/NMB-3(B) CAN ICES-6/NMB-6 Korea Warning Statements:
. NCC Notice 36 BSMI Notice PCB Pb Cd Hg CrVI PBB PBDE 1. "0.1 wt %" "0.01 wt %"
2. ""
3. " "
,
. Safety Information Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. Do not use the device where wireless devices are not allowed. 37 The socket-outlet shall be installed near the equipment and shall be easily accessible. Plug the powerline devices directly into the wall outlets but not the power strips. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk. For EU/EFTA, this product can be used in the following countries:
BE AT EE EL IT IS NO PL Explanation of the symbols on the product label Explanation BG CH CY CZ DE DK FR HR HU IE ES FI LT LI LU LV MT NL PT SK UK RO SE SI Symbol AC voltage Indoor use only Class II equipment RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. Protection earth 38
This product uses the FCC Data API but is not endorsed or certified by the FCC