DVW326 WeMTA User Manual

Ubee Interactive www.ubeeinteractive.com DVW326B Advanced Wireless Voice Gateway - Safety and Installation Product Insert to provide Federal Communications Commission

(FCC) Interference Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, the device may cause harmful interference to radio communications. There is no guarantee, however, that interference will not occur in a particular installation. If the DEVICE causes harmful interference to radio or television reception, which can be determined by turning it off and on, the user can try to correct the interference by one of the following measures:

Increase the separation between the DEVICE and the equipment with which it is interfering

(for example, a television or radio). Connect the DEVICE into an electrical outlet on a different circuit than the interfered device is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Regulatory Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any including interference that may cause undesired operation. interference received, There is one statement for this product:

Only the type of PIFA antenna tested may be used. 1 Ubee DVW326B Safety and Installation Product Insert Ubee Interactive www.ubeeinteractive.com FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. IEEE 802.11b,g,n operation of this device in the U.S.A. is firmware-limited to channels 1 through 11. FCC Radiation Exposure Statement:

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated at a minimum distance of 20cm between itself and your body. This device must not be co-located or operating in conjunction with any other antenna or transmitter. these Safety Notices Read carefully before operating the device. It is important to be aware of these safety instructions. Install the device according to these instructions and keep this guide for future reference. instructions 1. Do not use this device in a humid space, in the rain, or near splashing water. 2. Do not install during thunder or lightning storms. 3. Do not cover any ventilation openings in the device case. 4. Do not place the device near heat sources such as radiators or stoves. 5. Clean the device only with a clean, dry cloth. Do not use liquid or chemical cleaners. 6. Avoid static discharge when touching the device by first touching the coaxial connector of the coaxial cable. 2 Ubee DVW326B Safety and Installation Product Insert Ubee Interactive www.ubeeinteractive.com 7. Installation of the device should include grounding the coaxial cable to the earth at the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power systems with phase-to-phase voltage at 120V. 8. Disconnecting the Device: If the device becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. 9. The device should be installed in a location not to exceed the maximum temperature of 40 degrees Fahrenheit). degrees Celsius

(104 10. When this device is placed upright with the aid of the stand, the stand must be fixed at a 90-degree angle to the device. Otherwise, the device will have the risk of tipping over. 3 Installation To install this device, follow the procedures below and refer to the following page for a connection diagram. 1. Connect one end of a coaxial cable (not included) to the CABLE connector on the device. Connect the other end to a cable splitter or the cable wall outlet. Be sure not to bend or over tighten the cables as this may strain the connector and cause damage. If you plan to connect the device and a television to the same cable wall outlet, you must use a cable line splitter (not included). 2. Connect one end of the supplied Ethernet cable to one of the ETHERNET ports (ETH1 to ETH4) on the device. Connect the other end to the ETHERNET port on a PC. Note:

Category 5e or Category 6 Ethernet cables with RJ-45 connectors must be used when connecting Ethernet devices to the LAN ports. This ensures Gigabit Ethernet speeds (unless the computer does not support it). Ubee DVW326B Safety and Installation Product Insert Ubee Interactive www.ubeeinteractive.com 3. Connect one end of an RJ-11 phone cable to one of the TEL ports on the device (a port that has been provisioned for voice service as specified by the service provider). Connect the other end to the phone port of the telephone. Note:

is not provisioned the service provider, telephone service is not available. If voice service through DVW326B Advanced Wireless Voice Gateway 4. Connect the power cord to the POWER port on the device. Plug the other end of the power cord into the AC wall outlet. Important: Use only the power cord that is shipped with the device. 4 Ubee DVW326B Safety and Installation Product Insert Ubee Interactive www.ubeeinteractive.com 140mm (5.5 inches) Wall-Mount Installation You can mount the device on a wall using the 2 mounting brackets on the backside of the device. We recommend that you use two round or pan head screws. 1. Install two screws horizontally apart on a wall using the measurement shown to the right. The screws should protrude from the wall so that you can fit the device between the head of the screw and the wall. If you install the screws in drywall, use hollow wall anchors to ensure that the unit does not pull away from the wall due to prolonged strain from the coaxial and power cables. 2. Remove the device from the product package. 3. Mount the device on the wall. Refer to the following figure. The Distance of the Pothook (Horizontal) A 6.65+/-0.35 B 1.9+/-0.15 C 19.0+/1.20 A B C The Screws Size (mm) 5 Ubee DVW326B Safety and Installation Product Insert Ubee Interactive www.ubeeinteractive.com Additional Information 1. RESET Button (back of device): This button resets the device to factory defaults. Using a pointed object, insert it into the button opening, and hold for more than 10 seconds. The device will reset and reboot. Note: Not all parameters are reset to factory defaults. Refer to the User Guide for more information. 2. Battery (bottom of device): A slot is provided the battery and can be for battery insertion or that houses opened/closed replacement. 3. WPS button (top of device): The WPS button is used for the Wi-Fi Protected Setup (WPS) method to connect a Wi-Fi device to the DEVICE. Refer to the User Manual for more information. 4. USB Connector (back of device): If the USB connector is supported and enabled by the service provider, some USB devices can be connected here, such as computers, flash drives, etc. LEDs and Other Device Indicators See the following diagram and descriptions of the devices LED behavior, and the behavior of the back-panel Ethernet indicators. LED Indicators (Color = White When On):

PowerIf On, indicates that the has device successfully completed internal power-on tests. LED flashes if power-on fails. Note that the LED flashes briefly after powering the device. DS/USWhen device initializes, the LED flashes 1 flash per second until DS locks, then 2 flashes per second until US locks, then it is steady ON when both US and DS lock. When the device performs a firmware upgrade, the DS/US LED flashes. immediately the 6 Ubee DVW326B Safety and Installation Product Insert Ubee Interactive www.ubeeinteractive.com Back Panel Ethernet Indicators

(Color = Orange or Green):

When an Ethernet device, such as a computer, is connected to the device, the LED is Orange when connected at 10/100 Mbps speeds. When an Ethernet device, such as a computer, is connected to the device, the LED is Green when connected at 1000 Mbps speeds

(Gigabit Ethernet). When data is being passed between the device and the connected device, the LED flashes. On-lineWhen the device is obtaining an IP address and configuration file, the LED flashes. When device obtains these items, the LED is On. Wi-FiWhen Wi-Fi is enabled, the LED is On. When Wi-Fi is disabled, the LED is Off. TEL1 and TEL2The LED is On when a telephone is on-hook. The LED flashes when a telephone is off-hook. TEL1 or TEL2 is Off when the corresponding line is not provisioned. BatteryLED is On when the battery is installed and charged. LED is Off if no battery is installed. If the battery is at low power level (30mins left), the battery LED will flash. WPS (top of device)If not used, the LED is Off. When the user pushes the WPS button or triggers WPS via the devices web GUI, the LED flashes white for 4 minutes until a PIN is entered from a wireless client that wishes to connect. After a Wi-Fi client attaches successfully, the LED remains solid white for 5 minutes, and then turns off. 7 Ubee DVW326B Safety and Installation Product Insert