NanoBeam AC Users Manual

 

2.4 GHz airMAX ac CPE with Dedicated Wi-Fi Management Model: NBE-2AC-13 Introduction Thank you for purchasing the Ubiquiti Networks NanoBeamAC. This Quick Start Guide is designed to guide you through installation and also includes warrantyterms. Package Contents NanoBeam Ball Joint Mount Lock Ring Metal Strap Gigabit PoE (24V, 0.5A) with Mounting Bracket Power Cord Quick Start Guide 2.4 GHz airMAX ac CPE with Dedicated Wi-Fi Management Model: NBE-2AC-13 TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable is designed for outdoor installations. It is the professional installers responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements. Installation Requirements The NanoBeam can be mounted on a pole or to a wall. A Metal Strap (included) is used for pole-mounting. For wall-mounting, a suitable fastener such as a screw or bolt (not included) is required. Pole-mounting: 7 mm socket wrench or screwdriver Wall-mounting: wall fastener (not included) Shielded Category 5 (or above) cabling with drain wire should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the NanoBeam and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground. NBE-2AC-13 ES-8-150W ETH-SP ETH-SP To LAN Hardware Overview LEDs Polarity Align 2.4 GHz M/N: NBE-2AC-13 24V 0.5A GigE PoE FCC ID: SWX-NBE2ACN IC: 6545A-NBE2ACN RoHS Compliant This device complies with Part 15 of FCC rules. Operation is subject to the following 2 conditions:

1) this device may not cause harmful interference and, 2) this device must accept any interference received, including interference that may cause undesired operation. Reset Button Ethernet Port

(10/100/1000 Mbps) Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the NanoBeam is already poweredon. Alternatively, the NanoBeam may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Adapter. Ethernet Port This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. Power can be provided by any of the following:

Gigabit PoE adapter (included) Ubiquiti Networks EdgeSwitch Ubiquiti Networks EdgeRouter PoE LEDs Power The Power LED will light blue when the device is connected to a power source. Ethernet The Ethernet LED will light steady blue when an active Ethernet connection is made and flash when there is activity. Signal In airOS, you can modify the threshold value for the wireless signal strength LEDs on the Wireless tab under Signal LED Thresholds. Each LED will light when the wireless signal strength is equal to or greater than the LEDs threshold value. The default threshold values for these LEDs are shown below:

-94 dBm -80 dBm -73 dBm -65 dBm Hardware Installation The NanoBeam can be mounted on a pole or to a wall. Perform the steps for the appropriate installation:

Note: The NanoBeam can also be mounted inside a window using the NanoBeam Window Mount, model NBE-19-WM (sold separately). For instructions, see the NanoBeam Window Mount Quick Start Guide. Pole-Mount 1. Insert the Ball Joint Mount into the Lock Ring with the threads of the Lock Ring facing the ball joint. 2. Open the Metal Strap and feed it through the base of the Ball Joint Mount. 3. Wrap the Metal Strap around the pole. Use a 7 mm socket wrench to turn the screw clockwise and securely fasten the clamp to the pole. 4. Attach the NanoBeam to the Ball Joint Mount and turn the Lock Ring to secure it. Keep the Lock Ring loose enough to allow the NanoBeam to pivot for aiming. Wall-Mount The NanoBeam must be mounted directly to a wood stud or other structurally stable surface to avoid damage to the mounting hole when you adjust the aim. Optional Accessory To enhance stability, you can use the NanoBeam Wall Mount Kit, model NBE-WMK (soldseparately). Note: Center screw included. Two optional screws (not included) provide additional stability. Installation Instructions 1. Mark the desired location of the mounting point. 2. 3. If needed, drill a pilot hole for the fastener (not included). Insert the Ball Joint Mount into the Lock Ring with the threads of the Lock Ring facing the ball joint. 4. If you are using the optional NanoBeam Wall Mount Kit, then skip to step b. a. To attach the Ball Joint Mount to the wall, insert a fastener (not included) through the center of the ball joint, and into the wall. Securely tighten the fastener. Proceed to step 5. b. To attach the Ball Joint Mount to the wall, insert the Wall Mount Kit screw through the center of the ball joint, through the Wall Mount Kit plate, and into the wall. Securely tighten the screw. 5. Attach the NanoBeam to the Ball Joint Mount and turn the Lock Ring to secure it. Keep the Lock Ring loose enough to allow the NanoBeam to pivot for aiming. Aiming 1. Ensure the opening of the Ethernet cable is pointed towards the ground. 2. Aim the front of the NanoBeam towards the other end of the wireless link. 3. Hand-tighten the Lock Ring to lock the aim. Note: Do not use a tool to tighten the Lock Ring. Tighten the Lock Ring by hand only. Connecting Power 1. Remove the port cover by pressing down the center of the cover and sliding the cover out. Polarity Align 2.4 GHz 2. Connect an Ethernet cable to the Ethernet port. Polarity Align 2.4 GHz M/N: NBE-2AC-13 24V 0.5A GigE PoE FCC ID: SWX-NBE2ACN IC: 6545A-NBE2ACN RoHS Compliant This device complies with Part 15 of FCC rules. Operation is subject to the following 2 conditions:

1) this device may not cause harmful interference and, 2) this device must accept any interference received, including interference that may cause undesired operation. 3. Replace the port cover. 4. Connect the power using one of the following options:

Using the included Gigabit PoE Adapter: Go to Connecting to the PoE Adapter. Using a separate PoE switch: Connect the Ethernet cable from the NanoBeams Ethernet port to a PoE-enabled Ethernet port on the switch. WARNING: The switch port must comply with the power specifications listed in the Specifications section of this Quick Start Guide. Connecting to the PoE Adapter 1. Connect the Ethernet cable from the NanoBeams Ethernet port to the POE port of the Gigabit PoE adapter. 2. Connect an Ethernet cable from your LAN to the adapters LAN port. 3. Connect the Power Cord to the adapters power port. Connect the other end of the Power Cord to a power outlet. Mounting the PoE Adapter (Optional) 1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included). 3. Align the adapters slots with the tabs of the PoE Mounting Bracket, and then slide the adapterdown. Accessing airOS via Wi-Fi Verify connectivity in the airOS Configuration Interface. There are two methods, the U Mobile App and Web Portal. Both are available for 15 minutes immediately after you power on the NanoBeam. If necessary, you can power cycle the NanoBeam to re-enable its Wi-Fi. Proceed to the appropriate instructions:

U Mobile App 1. Download the U Mobile app from the AppStore (iOS) or Google Play (Android). 2. Connect your devices Wi-Fi to the NanoBeam SSID named: NBE-2AC-13:<MAC Address>

Note: Ensure that DHCP is enabled on your Wi-Fiadapter. 3. Launch the app. 4. Tap the NanoBeam on the Connections screen. 8:08 100 %

Connections Available NanoBeam 2AC 13 192.168.172.1 NBE-2AC-13: F09FC71EXXXX Connections Install Settings 5. Tap Connect on the Login screen. 8:08 Login 100 %

Connect NanoBeam 2AC 13 192.168.172.1 443 ubnt Name CONNECTION Address Port Require HTTPS CREDENTIALS Username Password NBE-2AC-13: F09FC71EXXXX 6. Select your Country and tap Done.

*640-00181-08*

640-00181-08 7. Customize your settings as needed. 8:09 Backup NanoBeam 2AC 13 100 %

Apply Wireless Network System Wireless Mode Station PtP WIRELESS SSID Select SSID... Security RADIO Country www.ubnt.com None United Kingdom Channel Width Auto - 20/40/80 MHz Control Frequency List Off ANTENNA Antenna Built-In - 13 dBi Status Configuration Tools Actions Web Portal 1. Connect your devices Wi-Fi to the NanoBeam SSID named: NBE-2AC-13:<MAC Address>

Note: Ensure that your Wi-Fi connection has DHCP enabled. 2. Launch a web browser and go to: http://setup.ubnt.com 3. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login. Note: The Country setting for U.S. product versions is restricted to a choice of Canada, Puerto Rico, or the U.S. to ensure compliance with FCC/IC regulations. The airOS Configuration Interface will appear, allowing you to customize your settings as needed. For additional details on the airOS Configuration Interface, refer to the User Guide available at www.ubnt.com/download/airmax Installer Compliance Responsibility Devices must be professionally installed and it is the professional installer's responsibility to make sure the device is operated within local country regulatory requirements. The Output Power field is provided to the professional installer to assist in meeting regulatory requirements. Specifications Dimensions (Mount Included) NBE-2AC-13 Weight (Mount Included) Gain Networking Interface Enclosure Max. Power Consumption Power Supply Power Method Wind Loading Wind Survivability Mounting ESD/EMP Protection Operating Temperature Operating Humidity Certifications 189 x 189 x 125 mm

(7.44 x 7.44 x 4.92") 530 g (1.17 lb) 13 dBi

(1) 10/100/1000 Ethernet Port Outdoor UV Stabilized Plastic 7.5W 24V, 0.5A Gigabit PoE Adapter (Included) Passive PoE (Pairs 4, 5+; 7, 8 Return) 45.4 N @ 200 km/h

(10.2 lbf @ 125 mph) 200 km/h

(125 mph) Pole-Mount (Kit Included) Wall-Mount (Not Included) Window-Mount (Not Included) 24kV Contact/Air

-40 to 80 C

(-40 to 176 F) 5 to 95% Noncondensing CE, FCC, IC Worldwide USA Worldwide USA Operating Frequency (MHz) Management Radio (MHz) 2412 - 2472 2412 - 2462 5150 - 5250 U-NII-3: 5725 - 5850 Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturers label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet. a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire. b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death. c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection. e. Protective bonding must be installed in accordance with local national wiring rules and regulations. Limited Warranty UBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) warrants that the product(s) furnished hereunder (the Product(s)) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty Conditions The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks authorized representatives, or as approved by Ubiquiti Networks in writing;

has been painted, rebranded or physically modified in any way;

has been damaged due to errors or defects in cabling;

has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;

has been damaged or impaired as a result of using third party firmware;

has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or has not been received by Ubiquiti within 30 days of issuance of the RMA.

(II)

(III)

(IV)

(V)

(VI)

(VII) In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed. Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYERS EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyers selection of products (including the Products) for buyers application and/or failure of products (including the Products) to meet government or regulatory requirements. Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products. Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This radio transmitter (FCC ID: SWX-NBE2ACN) has been approved by FCC. ISED Canada CAN ICES-3(A)/NMB-3(A) This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter (IC: 6545A-NBE2ACN) has been approved by ISEDCanada. CAN ICES-3(A)/NMB-3(A) Le prsent appareil est conforme aux CNR dISDE Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. 2. lappareil ne doit pas produire de brouillage;

lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Le prsent metteur radio (IC: 6545A-NBE2ACN) a t approuv par ISDECanada. RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 41 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilises pour ce transmetteur doivent tre install en considrant une distance de sparation de toute personnes dau moins 41cm et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur. Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. Deutsch Die Europische Richtlinie 2012/19/EU verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Fol fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Espaol La Directiva 2012/19/UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto. Franais La directive europenne 2012/19/UE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italiano La direttiva europea 2012/19/UE richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity

[Bulgarian] UBIQUITI NETWORKS , NBE-2AC-13 2014/53/.

:

www.ubnt.com/compliance Hrvatski [Croatian] UBIQUITI NETWORKS ovime izjavljuje da je radijska oprema tipa NBE-2AC-13 u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedeoj internetskoj adresi: www.ubnt.com/compliance etina [Czech] Tmto UBIQUITI NETWORKS prohlauje, e typ rdiovho zazen NBE-2AC-13 je v souladu se smrnic 2014/53/EU. pln znn EU prohlen o shod je k dispozici na tto internetov adrese: www.ubnt.com/compliance Dansk [Danish] Hermed erklrer UBIQUITI NETWORKS, at radioudstyrstypen NBE-2AC-13 er i overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklringens fulde tekst kan findes p flgende internetadresse: www.ubnt.com/compliance Nederlands [Dutch] Hierbij verklaar ik, UBIQUITI NETWORKS, dat het type radioapparatuur NBE-2AC-13 conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres:

www.ubnt.com/compliance English Hereby, UBIQUITI NETWORKS declares that the radio equipment type NBE-2AC-13 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.ubnt.com/compliance Eesti keel [Estonian] Kesolevaga deklareerib UBIQUITI NETWORKS, et kesolev raadioseadme tp NBE-2AC-13 vastab direktiivi 2014/53/EL nuetele. ELi vastavusdeklaratsiooni tielik tekst on kttesaadav jrgmisel internetiaadressil: www.ubnt.com/compliance Suomi [Finnish] UBIQUITI NETWORKS vakuuttaa, ett radiolaitetyyppi NBE-2AC-13 on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen tysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.ubnt.com/compliance Franais [French] Le soussign, UBIQUITI NETWORKS, dclare que lquipement radiolectrique du type NBE-2AC-13 est conforme la directive 2014/53/UE. Le texte complet de la dclaration UE de conformit est disponible ladresse internet suivante: www.ubnt.com/compliance Deutsch [German] Hiermit erklrt UBIQUITI NETWORKS, dass der Funkanlagentyp NBE-2AC-13 der Richtlinie 2014/53/EU entspricht. Der vollstndige Text der EU-Konformittserklrung ist unter der folgenden Internetadresse verfgbar: www.ubnt.com/compliance

[Greek] / UBIQUITI NETWORKS, NBE-2AC-13 2014/53/.

: www.ubnt.com/compliance Magyar [Hungarian] UBIQUITI NETWORKS igazolja, hogy a NBE-2AC-13 tpus rdiberendezs megfelel a 2014/53/EU irnyelvnek. Az EU-megfelelsgi nyilatkozat teljes szvege elrhet a kvetkez internetes cmen: www.ubnt.com/compliance slenska [Icelandic] Hr me lsir UBIQUITI NETWORKS yfir v a NBE-2AC-13 er samrmi vi grunnkrfur og arar krfur, sem gerar eru tilskipun 2014/53/EU. Fullur texti ESB samrmisyfirlsing er a finna eftirfarandi netfangi: www.ubnt.com/compliance Italiano [Italian] Il fabbricante, UBIQUITI NETWORKS, dichiara che il tipo di apparecchiatura radio NBE-2AC-13 conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformit UE disponibile al seguente indirizzo Internet: www.ubnt.com/compliance Latvi kalba [Latvian] Ar o UBIQUITI NETWORKS deklar, ka radioiekrta NBE-2AC-13 atbilst Direktvai 2014/53/ES. Pilns ES atbilstbas deklarcijas teksts ir pieejams d interneta vietn:

www.ubnt.com/compliance Lietuvi kalba [Lithuanian] A, UBIQUITI NETWORKS, patvirtinu, kad radijo rengini tipas NBE-2AC-13 atitinka Direktyv 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas iuo interneto adresu: www.ubnt.com/compliance Malti [Maltese] Bdan, UBIQUITI NETWORKS, niddikjara li dan it-tip ta tagmir tar-radju NBE-2AC-13 huwa konformi mad-Direttiva 2014/53/UE. Id-dikjarazzjoni tal-konformit tista tii kkonsultata minn www.ubnt.com/compliance Norsk [Norwegian] UBIQUITI NETWORKS erklrer herved at utstyret NBE-2AC-13 er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU-samsvarserklringen er tilgjengelig p flgende internettadresse:

www.ubnt.com/compliance Polski [Polish] UBIQUITI NETWORKS niniejszym owiadcza, e typ urzdzenia radiowego NBE-2AC-13 jest zgodny z dyrektyw 2014/53/UE. Peny tekst deklaracji zgodnoci UE jest dostpny pod nastpujcym adresem internetowym: www.ubnt.com/compliance Portugus [Portuguese] O(a) abaixo assinado(a) UBIQUITI NETWORKS declara que o presente tipo de equipamento de rdio NBE-2AC-13 est em conformidade com a Diretiva 2014/53/UE. O texto integral da declarao de conformidade est disponvel no seguinte endereo de Internet:

www.ubnt.com/compliance Romn [Romanian] Prin prezenta, UBIQUITI NETWORKS declar c tipul de echipamente radio NBE-2AC-13 este n conformitate cu Directiva 2014/53/UE. Textul integral al declaraiei UE de conformitate este disponibil la urmtoarea adres internet: www.ubnt.com/compliance Slovenina [Slovak] UBIQUITI NETWORKS tmto vyhlasuje, e rdiov zariadenie typu NBE-2AC-13 je v slade so smernicou 2014/53/E. pln E vyhlsenie o zhode je k dispozcii na tejto internetovej adrese: www.ubnt.com/compliance Slovenina [Slovenian] UBIQUITI NETWORKS potrjuje, da je tip radijske opreme NBE-2AC-13 skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.ubnt.com/compliance Espaol [Spanish] Por la presente, UBIQUITI NETWORKS declara que el tipo de equipo radioelctrico NBE-2AC-13 es conforme con la Directiva 2014/53/UE. El texto completo de la declaracin UE de conformidad est disponible en la direccin Internet siguiente:

www.ubnt.com/compliance Svenska [Swedish] Hrmed frskrar UBIQUITI NETWORKS att denna typ av radioutrustning NBE-2AC-13 verensstmmer med direktiv 2014/53/EU. Den fullstndiga texten till EU-frskran om verensstmmelse finns p fljande webbadress: www.ubnt.com/compliance Online Resources Website www.ubnt.com Support help.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com Ubiquiti Networks, Inc. 685 Third Avenue, 27th Floor New York, NY 10017 USA 2017 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, EdgeRouter, EdgeSwitch, NanoBeam, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple, the Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android, Google, Google Play, the Google Play logo and other marks are trademarks of Google Inc. All other trademarks are the property of their respective owners. NBAI082117