| submitted | available | document details (if available) | source link |
|---|---|---|---|
| February 05 2019 |
| various | User Manual | Users Manual | 333.06 KiB | February 05 2019 |
MS-01 SOM Module
`
1. WiFi and Bluetooth MS-01 Integrated Qualcomm WCN3990 to support WLAN 2x2 802.11a/b/g/n/ac with DBS and 160 MHz, Bluetooth 5.0. n 2 2 802.11ac with MU-MIMO n DBS support n 160 MHz bandwidth support n Bluetooth 5.0 1.1 WLAN RF Characteristics 1.1.1 2.4 GHz WLAN Transmitter Characteristic Parameter 1 Mbps DSSS (b) TX Output power 11 Mbps DSSS (b) TX Output power 6 Mbps OFDM (g) TX Output power 54 Mbps OFDM (g) TX Output power MCS0 OFDM (n) TX Output power, 20 MHz MCS7 OFDM (n) TX Output power, 20 MHz MCS0 OFDM (n) TX Output power, 40 MHz MCS7 OFDM (n) TX Output power, 40 MHz Test Conditions 1 Mbps BPSK 802.11(b) Mask Compliance 35%
EVM RMS power over TX packet, 20 MHz 11 Mbps CCK 802.11(b) Mask Compliance 35%
EVM RMS power over TX packet, 20 MHz 6 Mbps BPSK 802.11(g) Mask Compliance -5 dB EVM RMS power over TX packet, 20 MHz 54 Mbps 64-QAM 802.11(g) Mask Compliance -25 dB EVM RMS power over TX packet, 20 MHz 6.5 Mbps BPSK 802.11(n) Mask Compliance -5 dB EVM RMS power over TX packet, 20 MHz 65 Mbps 64-QAM 802.11(n) Mask Compliance -27 dB EVM RMS power over TX packet, 20 MHz 13.5 Mbps BPSK 802.11(n) Mask Compliance -5 dB EVM RMS power over TX packet, 40 MHz 135 Mbps 64-QAM 802.11(n) Mask Compliance -27 dB EVM RMS power over TX packet, 40 MHz Typ 18 +/- 1.5 18 +/- 1.5 16 +/- 1.5 14 +/- 1.5 16 +/- 1.5 13 +/- 1.5 16 +/- 1.5 13 +/- 1.5 Unit dBm dBm dBm dBm dBm dBm dBm dBm All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 1 MS-01 SOM Module
`
1.1.2 2.4 GHz WLAN Receiver Characteristic Parameter Test Conditions 1 Mbps DSSS (b) Rx Sensitivity 11 Mbps DSSS (b) Rx Sensitivity 6 Mbps OFDM (g) Rx Sensitivity 54 Mbps OFDM (g) Rx Sensitivity MCS0 OFDM (n) Rx Sensitivity MCS7 OFDM (n) Rx Sensitivity MCS0 OFDM (n) Rx Sensitivity MCS7 OFDM (n) Rx Sensitivity 802.11b RX Overload Level - 20MHz 802.11g RX Overload Level - 20MHz 802.11n RX Overload Level - 20MHz 1.1.3 5 GHz WLAN Transmitter Characteristics 8% PER, 20 MHz 8% PER, 20 MHz 10% PER, 20 MHz 10% PER, 20 MHz 10% PER, 20 MHz 10% PER, 20 MHz 10% PER, 40 MHz 10% PER, 40 MHz 8% PER, 11 Mbps 10% PER, 54 MHz 10% PER, MCS7 Min
-
-
-
-
-
-
-
-
-10
-20
-20 Typ Max Unit
-96 dBm dBm
-88 dBm
-91 dBm
-74 dBm
-91 dBm
-71 dBm
-88 dBm
-69
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Parameter Test Conditions 6 Mbps OFDM (a) TX Output power 54 Mbps OFDM (a) TX Output power 6 Mbps BPSK 802.11(a) Mask Compliance -5 dB EVM RMS power over TX packet, 20 MHz 54 Mbps 64-QAM 802.11(a) Mask Compliance -
25 dB EVM RMS power over TX packet, 20 MHz MCS0 OFDM (n) TX Output power, 20 MHz 6.5 Mbps BPSK 802.11(n) Mask Compliance -5 dB EVM RMS power over TX packet, 20 MHz MCS7 OFDM (n) TX Output power, 20 MHz 65 Mbps 64-QAM 802.11(n) Mask Compliance -
27 dB EVM RMS power over TX packet, 20 MHz MCS0 OFDM (n) TX Output power, 40 MHz 13.5 Mbps BPSK 802.11(n) Mask Compliance -5 dB EVM RMS power over TX packet, 40 MHz MCS0 OFDM (ac) TX Output power, 20 MHz MCS8 OFDM (ac) TX Output power, 20 MHz MCS0 OFDM (ac) TX Output power, 40 MHz MCS9 OFDM (ac) TX Output power, 40 MHz MCS7 OFDM (n) TX Output power, 40 MHz 135 Mbps 64-QAM 802.11(n) Mask Compliance -
27 dB EVM RMS power over TX packet, 40 MHz BPSK 802.11(ac) Mask Compliance -5 dB EVM RMS power over TX packet, 20 MHz 64-QAM 802.11(ac) Mask Compliance -30 dB EVM RMS power over TX packet, 20 MHz 13.5 Mbps BPSK 802.11(ac) Mask Compliance -5 dB EVM RMS power over TX packet, 40 MHz 180 Mbps 256-QAM 802.11(ac) Mask Compliance -32 dB EVM RMS power over TX packet, 40 MHz 29.3 Mbps BPSK 802.11(ac) Mask Compliance -5 dB EVM RMS power over TX packet, 80 MHz 390 Mbps 256-QAM 802.11(ac) Mask Compliance -32 dB EVM RMS power over TX packet, 40 MHz MCS0 OFDM (ac) TX Output power, 80 MHz MCS9 OFDM (ac) TX Output power, 80 MHz Typ 16 +/- 1.5 14 +/- 1.5 16 +/- 1.5 13 +/- 1.5 16 +/- 1.5 13 +/- 1.5 16 +/- 1.5 12 +/- 1.5 16 +/- 1.5 Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm 11 +/- 1.5 dBm 16 +/- 1.5 dBm 11 +/- 1.5 dBm All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 2 MS-01 SOM Module
`
1.1.4 5 GHz WLAN Receiver Characteristics Test Conditions Min
-
-
-
-
-
-
-
-
-
-
-
-
10% PER, 20 MHz 10% PER, 20 MHz 10% PER, 20 MHz 10% PER, 20 MHz 10% PER, 40 MHz 10% PER, 40 MHz 10% PER, 20 MHz 10% PER, 20 MHz 10% PER, 40 MHz 10% PER, 40 MHz 10% PER, 80 MHz 10% PER, 80 MHz Typ Max Unit
-92 dBm dBm
-75 dBm
-91 dBm
-73 dBm
-88 dBm
-70 dBm
-91 dBm
-68 dBm
-88 dBm
-64
-84 dBm dBm
-59 1. Parameter 6 Mbps OFDM (a) Rx Sensitivity 54 Mbps OFDM (a) Rx Sensitivity MCS0 OFDM (n) Rx Sensitivity MCS7 OFDM (n) Rx Sensitivity MCS0 OFDM (n) Rx Sensitivity MCS7 OFDM (n) Rx Sensitivity MCS0 OFDM (ac) Rx Sensitivity MCS8 OFDM (ac) Rx Sensitivity MCS0 OFDM (ac) Rx Sensitivity MCS9 OFDM (ac) Rx Sensitivity MCS0 OFDM (ac) Rx Sensitivity MCS9 OFDM (ac) Rx Sensitivity 2. Bluetooth RF Characteristics MS-01 Integrated Qualcomm WCN3990 to Support Bluetooth 5.0 and is backwards compatible with previous BT standard revisions. 2.1 Bluetooth RF Characteristics The following tables show the Bluetooth transmitting and receiving performance
-
-
-
-
-
-
-
-
-
-
-
-
Transmitter Performance Packet Types DH5 2-DH5 3-DH5 Transmitting Power 11 +/- 1.5 dB 8 +/- 1.5 dB 8 +/- 1.5 dB Receiver Performance Packet Types Receiving Sensitivity DH5
-93 dBm 2-DH5
-93 dBm 3-DH5
-86 dBm All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 3 MS-01 SOM Module
`
OEM/Integrators Installation Manual Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module's intentional emissions are compliant (i.e. fundamental and out of band emissions). The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s). Antenna Installation
(1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
(2) The transmitter module may not be co-located with any other transmitter or antenna.
(3) To comply with FCC/IC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile exposure condition must not exceed:
Standalone Condition:
1.44 dBi in 2.4 GHz Band 2.16 dBi in 5.2GHz Band 2.16 dBi in 5.3GHz Band 2.16 dBi in 5.5GHz Band 2.16 dBi in 5.8GHz Band In the event that these conditions cannot be met (for example certain laptop configurations or co-
location with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/IC authorization. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 4 MS-01 SOM Module
`
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
-
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 5 MS-01 SOM Module
`
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: COF-MS01. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 6 MS-01 SOM Module
`
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed with 20 cm is maintained between the antenna and users in mobile or fixed applications. 2) The Antenna for Module (MS-01) is Non-detachable and the maximum antenna gain allowed for use with this device is 1.44 dBi.@2.4GHz band & 2.16dBi@5GHz band. 3) The transmitter module may not be co-located with any other transmitter or antenna. 4) OEM integrators Must demonstrate SAR test and meet compliance before end-product with module (MS-01) marketed in portable application. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. OEM integrators Must demonstrate Part 15B test and meet compliance before end-product with module (MS-01) marketed. US Information Name of the company: USI America, Inc Address of the company: 2000 Regency Parkway, Suite 420, Cary, NC 27518 Phone number: 919-466-8688 Ext. 109 General The SOM module uses Dipole antenna to do EMC official test then antenna gain and trace design, please refer to antenna information and antenna trace design. Antenna Information Antenna Type: Dipole Antenna gain: 1.44dBi@2.4GHz and 2.16dBi@5GHz All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 7 MS-01 SOM Module
`
Antenna Trace Design WLAN chain0/BT Top layer WLAN chain1 Top layer All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 8 MS-01 SOM Module
`
Industry Canada statement:
This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 9 MS-01 SOM Module
`
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-
location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC:10293A-MS01. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 10 MS-01 SOM Module
`
Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:
"Contient des IC: 10293A-MS01 ". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 11 MS-01 SOM Module
`
RSS-247 Section 6.4 (5) (6) (for local area network devices, 5GHz) The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
The maximum antenna gain permitted for devices in the bands 52505350 MHz and 54705725 MHz shall comply with the e.i.r.p. limit; and The maximum antenna gain permitted for devices in the band 57255825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. L'appareil peut interrompre automatiquement la transmission en cas d'absence d'informations transmettre ou de panne oprationnelle. Notez que ceci n'est pas destin interdire la transmission d'informations de contrle ou de signalisation ou l'utilisation de codes rptitifs lorsque cela est requis par la technologie. Le dispositif utilis dans la bande 5150-5250 MHz est rserv une utilisation en intrieur afin de rduire le risque de brouillage prjudiciable aux systmes mobiles par satellite dans le mme canal;
Le gain d'antenne maximal autoris pour les dispositifs dans les bandes 5250-5350 MHz et 5470-5725 MHz doit tre conforme la norme e.r.p. limite; et Le gain d'antenne maximal autoris pour les appareils de la bande 5725-5825 MHz doit tre conforme la norme e.i.r.p. les limites spcifies pour un fonctionnement point point et non point point, selon le cas. All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 12 MS-01 SOM Module
`
CE RF exposure RF Exposure Information (MPE) This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. To comply with the RF exposure requirements, this module must be installed in a host platform that is intended to be operated in a minimum of 20 cm separation distance to the user. Hereby, USI declares that the radio equipment type WiFi SOM Module is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://www.usiglobal.com/tw/MS-01/DoC.pdf In all cases assessment of the final product must be met against the Essential requirements of the RE Directive Articles 3.1(a) and (b), safety and EMC respectively, as well as any relevant Article 3.3 requirements. 1. The Dipole antenna (WLAN/BT: 1.44dBi@2.4GHz,2.16dBi@5GHz) was verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations. 2. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and CE equipment certification is required. The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range. AT EE IT PT BE FI LV RO BG FR LT SK HR DE LU SI CY EL MT ES CZ HU NL SE DK IE PL UK All rights are reserved by USI. No part of this technical document can be reproduced in any form without permission of USI. Page 13
This product uses the FCC Data API but is not endorsed or certified by the FCC