WMNBM30 Wireless WICED module Users Manual

 

WM-N-BM-30 User manual HW Application note for WM-N-BM-30 Please find detail information from link as below, https://www.olimex.com/Products/ARM/JTAG/ARM-USB-TINY-H/

ST-Link/v2 Utility :

http://www.st.com/st-web-ui/static/active/en/st_prod_software_internet/resource/technical/soft ware/utility/stsw-link004.zip ST-Link/v2 driver :

http://www.st.com/st-web-ui/static/active/en/st_prod_software_internet/resource/technical/soft ware/driver/st-link_v2_usbdriver.zip Doc No. Date. 2015-05-04 Rev Page 1.1 3 Universal Scientific Industrial Corp.. Document released by WP/RD/WM/HW1 Description WM-N-BM-30 Application Note 1. Characteristic Option 1.1 Boot mode At startup, boot pins are used to select one out of three boot options:

Boot from user Flash Boot from system memory Boot from embedded SRAM The boot loader is located in system memory. It is used to reprogram the Flash memory by using USART1(PA9/10), USART2(PD5/6), USB OTG FS in device mode (PA11/12) through DFU (device firmware upgrade), I2C1(PB6/7), I2C2(PB10/3), I2C3(PA8/PB4), SPI1(PA4/5/6/7), SPI2(PB12/13/14/15) or SPI3(PA15, PC10/11/12). Low Boot from user Flash BOOT0 High Boot from system memory / embedded SRAM VDD_3V3 R1 10k BOOT PIN 1 2 Header1x2 JP1 BOOT PIN WM-N-BM-30 set the BOOT0 to GND, the Boot mode is Main Flash memory. When BOOT0 set to High, the BOOT mode is system memory. 3 The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorized in writing by Universal Scientific Industrial Co., Ltd. Copyright 2011 Universal Scientific Industrial Co. ,Ltd. Universal Scientific Industrial Corp.. Document released by WP/RD/WM/HW1 Description WM-N-BM-30 Application Note 1.2 Low Power mode Doc No. Date. 2015-05-04 Rev Page 1.1 4 By default, the microcontroller is in Run mode after a system or a power-on reset. In Run mode the CPU is clocked by HCLK and the program code is executed. Several low-power modes are available to save power when the CPU does not need to be kept running, for example when waiting for an external event. It is up to the user to select the mode that gives the best compromise between low-power consumption, short startup time and available wakeup sources. The devices feature three low-power modes:

Sleep mode (Cortex-M3 core stopped, peripherals kept running) Stop mode (all clocks are stopped) Standby mode (1.2 V domain powered off) 1.3 MOS for WIFI_3V3 Power ON/OFF External MOS for VDD_WIFI_3V3 power switch , can use one GPIO pin to control power ON/OFF 4 The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used, except as authorized in writing by Universal Scientific Industrial Co., Ltd. Copyright 2011 Universal Scientific Industrial Co. ,Ltd. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. End Product Labeling (FCC) When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text:

Contains FCC ID: COFWMNBM30. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Required FCC Compliance Statement for Host Integration To integrate this module into the host, the host manufacturer is responsible for the applicable FCC rules, including the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. In the user manual of the host device, the following statements are required to be included.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

- 1 -

Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Module Integration Restriction:

This module has been certified by FCC as single module approval with the following restrictions:

1. The chip antenna with 2.04 dBi gain was verified in the conformity testing. Radiated transmit power must be equal to or lower than that specified in the FCC Grant of Equipment Authorization for FCC ID: COFWMNBM30. A separate approval is required for all other operating configurations. 2. This module can be installed in portable, mobile, or fixed application. To assure RF Exposure compliance, the antenna must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi transmitter product procedure. 3. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and FCC equipment authorization is required.

- 2 -

End Product Labeling (IC) When the module is installed in the host device, the IC label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text:

Contains IC: 10293A-WMNBM30. The grantee's IC ID can be used only when all IC compliance requirements are met. Required IC Compliance Statement for Host Integration This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement."

CAN ICES-3(B)/ NMB-3(B) IC Module Integration Restriction:

1. The chip antenna with 2.04 dBi gain was verified in the conformity testing. In case any modification in the radio equipment which do change the electrical characteristics beyond the rated limits established by the manufacturer and accepted by Industry Canada for IC ID 10293A-WMNBM30, a separate approval is required.

- 3 -

2. This module can be installed in portable, mobile, or fixed application. To assure RF Exposure compliance, the antenna must not transmit simultaneously with any other antenna or transmitter, except in accordance with IC multi transmitter product procedure. 3. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, the Canada authorization is no longer considered valid and the IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Industry Canada authorization. FCC ID:

COFWMNBM30 IC: 10293A-WMNBM30

- 4 -

R&TTE Regulation:

In all cases assessment of the final product must be met against the Essential requirements of the R&TTE Directive Articles 3.1(a) and (b), safety and EMC respectively, as well as any relevant Article 3.3 requirements. 1. The chip antenna (gain: 2.04 dBi) was verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations. 2. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and CE equipment certification is required.

******************************************************************************

1.1 Europe EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:

EN 60950-1: 2006+A11:2009+A1:2010+A12:2011 EN 62311:2008 EN 62479 :2010 EN300 328 V 1.8.1:2012 EN 301 489-1 V1.9.2:2011 EN 301 489-17 V 2.2.1 :2012 National Authorities were informed according to Article 6.4 of Frequency Notification. Special Requirements are considered. The product is labeled with CE Marking.

- 5 -

esky

[Czech]

Dansk

[Danish]

Deutsch

[German]

Eesti

[Estonian]

English Espaol

[Spanish]

[Greek]

Franais

[French]

Italiano

[Italian]

Latviski

[Latvian]

Lietuvi

[Lithuanian]

Nederlands

[Dutch]

Malti

[Maltese]

Magyar

[Hungarian]

Polski

[Polish]

[Jmno vrobce] tmto prohlauje, e tento [typ zazen] je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Undertegnede [fabrikantens navn] erklrer herved, at flgende udstyr

[udstyrets typebetegnelse] overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hiermit erklrt [Name des Herstellers], dass sich das Gert [Gertetyp] in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Kesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tp = type of equipment] vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

[name of manufacturer] [type of equipment]

1999/5/. Par la prsente [nom du fabricant] dclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o [name of manufacturer / izgatavotja nosaukums] deklar, ka [type of equipment / iekrtas tips] atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo [manufacturer name] deklaruoja, kad is [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]

jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Alulrott, [gyrt neve] nyilatkozom, hogy a [... tpus] megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Niniejszym [nazwa producenta] owiadcza, e [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami

- 6 -

Dyrektywy 1999/5/EC.

[Nome do fabricante] declara que este [tipo de equipamento] est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE.

[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES.

[Meno vrobcu] tmto vyhlasuje, e [typ zariadenia] spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES.

[Valmistaja = manufacturer] vakuuttaa tten ett [type of equipment = laitteen tyyppimerkint] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hrmed intygar [fretag] att denna [utrustningstyp] str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Portugus

[Portuguese

]

Slovensko

[Slovenian]

Slovensky

[Slovak]

Suomi

[Finnish]

Svenska

[Swedish]

- 7 -