| submitted | available | document details (if available) | source link |
|---|---|---|---|
| December 11 2002 | August 11 2002 |
| various | users manual | Users Manual | 246.10 KiB | December 11 2002 / August 11 2002 |
FCC ID: K66FT-2800M OPERATING MANUAL FT-2800M Operating Manual Introduction The FT-2800M is a deluxe, rugged FM mobile transceiver providing high power output and outstanding receiver performance for the 144 MHz band. Included in the FT-
2800Ms feature complement are:
60 Watts of power output, with selection of four power levels for every operating situation.
Expanded receiver coverage: 137-174 MHz.
Keyboard entry of operating frequencies from the microphone.
Excellent protection from receiver intermodulation distortion, thanks to Yaesus renowned Advanced Track Tuning front end.
219 memories which can store repeater shifts, odd repeater shifts, CTCSS/DCS tones, and 6-character Alpha-Numeric labels for easy channel recognition.
10 NOAA Weather Broadcast Channel.
Built-in CTCSS and DCS Encoder/Decoder circuits.
The Smart SearchTM feature, which automatically sweeps a band and loads active frequencies into dedicated memory banks, is ideal for identifying active repeaters when visiting a city for the first time.
Extensive Menu system, which allows customization of a number of transceiver performance characteristics.
The Yaesu-exclusive multi-function LCD display. Additional features include a transmit Time-Out-Timer (TOT), Automatic Power-Off
(APO), Automatic Repeater Shift (ARS), plus provision for reduction of the Tx deviation in areas of high channel congestion. And an RF Squelch circuit allows the owner to set the squelch to open at a programmable setting of the S-Meter, thus reducing guesswork in setting the squelch threshold. Congratulations on your purchase of the FT-2800M! Whether this is your first rig, or if Yaesu equipment is already the backbone of your station, the Yaesu organization is committed to ensuring your enjoyment of this high-performance transceiver, which should provide you with many years of satisfying operation. Yaesus dealer network and technical support personnel stand behind every product we sell, and we invite you to contact us should you require technical advice or assistance. We recommend that you read this manual in its entirety prior to installing the FT-
2800M, so that you fully understand the capabilities of your new transceiver. 1 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Specifications Tx 144 - 146 MHz or 144 - 148 MHz Rx 144 - 146 MHz or 137 - 174 MHz 5/10/12.5/15/20/25/50/100 kHz 600 kHz better than 10 ppm
[4 F to +140 F (20 C to +60 C)]
F2/F3 50-ohms, unbalanced 13.8 V DC 15%, negative ground Rx: less than 0.7 A, less than 0.3 A (squelched) Tx: 10 A (60 W)/6 A (25 W)/3 A (10 W)/2 A (5 W)
????
6.3 x 2.0 x 7.3 inch (160 x 50 x 185 mm) (w/o knobs) 4.0 lb (1.8 kg) 60 W/25 W/10 W/5 W Variable Reactance 5 kHz/2.5 kHz better than 60 dB 2-kohm General Frequency Range:
Channel Step:
Standard Repeater Shift Frequency Stability:
Mode of Emission:
Antenna Impedance:
Supply voltage:
Current Consumption (typical):
Operating Temperature Range:
Case Size (WxHxD):
Weight (Approx.):
Transmitter Output Power:
Modulation Type:
Maximum Deviation:
Spurious Radiation:
Microphone Impedance:
Receiver Circuit Type:
Ifs:
Sensitivity (for 12dB SINAD):
Selectivity (6/60dB):
IF Rejection:
Image Rejection:
Adjacent Channel Selectivity Inter Modulation Maximum AF Output:
Specifications subject to change without notice or obligation. Double Conversion Superheterodyne 21.7 MHz & 450 kHz better than 0.2 V 12 kHz/28 kHz better than 70 dB better than 70 dB better than 70 dB better than 95 dB 3.5 W into 4-ohms @10 % THD 2 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Accessory & Options Supplied Accessories Microphone MH-48A6J 1 Mobile Mounting Bracket MMB-?? 1 DC Power Cord w/Fuse (T9????????) 1 Spare Fuse 15 A (Q????????) 1 Standing Foot (R????????) 2 Operating Manual 1 Warranty Card 1 Optional Accessories
????????
????????
Installation This chapter describes the installation procedure for integrating the FT-2800M into a typical amateur radio station. It is presumed that you possess technical knowledge and conceptual understanding consistent with your status as a licensed radio amateur. Please take some extra time to make certain that the important safety and technical requirements detailed in this chapter are followed closely. Preliminary Inspection Inspect the transceiver visually immediately upon opening the packing carton. Confirm that all controls and switches work freely, and inspect the cabinet for any damage. Gently shake the transceiver to verify that no internal components have been shaken loose due to rough handling during shipping. If any evidence of damage is discovered, document it thoroughly and contact the shipping company (or your local dealer, if the unit was purchased over-the-counter) so as to get instructions regarding the prompt resolution of the damage situation. Be certain to save the shipping carton, especially if there are any punctures or other evidence of damage incurred during shipping; if it is necessary to return the unit for service or replacement, use the original packing materials but put the entire package inside another packing carton, so as to preserve the evidence of shipping damage for 3 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL insurance purposes. Installation Tips To ensure long life of the components, be certain to provide adequate ventilation around the cabinet of the FT-2800M. Do not install the transceiver on top of another heat-generating device (such as a power supply or amplifier), and do not place equipment, books, or papers on top of the FT-
2800M. Avoid heating vents and window locations that could expose the transceiver to excessive direct sunlight, especially in hot climates. The FT-2800M should not be used in an environment where the ambient temperature exceeds +60 C. Safety Information The FT-2800M is an electrical apparatus, as well as a generator of RF (Radio Frequency) energy, and you should exercise all safety precautions as are appropriate for this type of device. These safety tips apply to any device installed in a well-designed amateur radio station.
(!): Never allow unsupervised children to play in the vicinity of your transceiver or antenna installation.
(!): Be certain to wrap any wire or cable splices thoroughly with insulating electrical tape, to prevent short circuits.
(!): Do not route cables or wires through door jambs or other locations where, through wear and tear, they may become frayed and shorted to ground or to each other.
(!): Do not stand in front of a directional antenna while you are transmitting into that antenna. Do not install a directional antenna in any location where humans or pets may be walking in the main directional lobe of the antennas radiation pattern.
(!): In mobile installations, it is preferable to mount your antenna on top of the roof of the vehicle, if feasible, so as to utilize the car body as a counterpoise for the antenna and raise the radiation pattern as far away from passengers as possible.
(!): During vehicular operation when stopped (in a parking lot, for example), make it a practice to switch to Low power if there are people walking nearby.
(!): Never wear dual-earmuff headphones while driving a vehicle.
(!): Do not attempt to drive your vehicle while making a telephone call on an autopatch using the DTMF microphone. Pull over to the side of the road, whether dialing manually or using the auto-dial feature. 4 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Antenna Consideration The FT-2800M is designed for use with antennas presenting an impedance of near 50 Ohms at all operating frequencies. The antenna (or a 50 Ohm dummy load) should be connected whenever the transceiver is turned on, to avoid damage that could otherwise result if transmission occurs accidentally without an antenna. Ensure that your antenna is designed to handle 60 Watts of transmitter power. Some magnetic-mount mobile antennas, designed for use with hand-held transceivers, may not be capable of withstanding this power level. Consult the antenna manufacturers specification sheet for details. Most all FM work is performed using vertical polarization. When installing a directional antenna such as a Yagi or Cubical Quad, be certain to orient it so as to produce vertical polarization, unless you are engaged in a special operating situation where horizontal polarization is used. In the case of a Yagi antenna, orient the elements vertically for vertical polarization; for a Cubical Quad, the feedpoint should be at the center of one of the vertical sides of the driven element (or at a side corner, in the case of a diamond-
shaped Cubical Quad). Excellent reference texts and computer software are available for the design and optimization of VHF antennas. Your dealer should be able to assist you with all aspects of your antenna installation requirements. Use high-quality 50 Ohm coaxial cable for the lead-in to your FT-2800M transceiver. All efforts at providing an efficient antenna system will be wasted if poor quality, lossy coaxial cable is used. Losses in coaxial lines increase as the frequency increases, so an 8-meter-long (25 coaxial line with 1/2 dB of loss at 29 MHz may have a loss of 1.8 dB or more at 146 MHz; choose your coaxial cable carefully based on the installation location
(mobile vs. base) and the overall length of the cable required (for very short runs of cable in a mobile installation, the smaller, more flexible cable types may be acceptable). For reference, the chart below shows approximate loss figures for typically-available coaxial cables frequently used in VHF installations.
<<Cable Chart>>
5 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Loss figures are approximate; consult cable manufacturers catalogs for complete specifications. In outdoor installations, be certain to weatherproof all connectors thoroughly, as water entering a coaxial cable will cause losses to escalate rapidly, thus diminishing your communications effectiveness. The use of the shortest possible length of the highest quality coaxial cable that fits within your budget will ensure the best performance from your FT-2800M. Mobile Installation The FT-2800M must only be installed in vehicles having a 13.8 Volt negative ground electrical system. Mount the transceiver where the display, controls, and microphone are easily accessible, using the supplied MMB-?? mounting bracket. The transceiver may be installed in almost any location, but should not be positioned near a heating vent nor anywhere where it might interfere with driving (either visually or mechanically). Make sure to provide plenty of space on all sides of the transceiver so that air can flow freely around the radios case. Refer to the diagrams showing proper installation procedures. Transceiver Installation
Choose a mounting location with sufficient clearance for the transceiver. Using the mounting bracket as a template for the mounting holes, use a 4.8 mm (3/16 bit to drill the mounting holes, and secure the mounting bracket with the supplied screws, washers, and nuts (see diagram).
Position the transceiver in the bracket so that the holes in the side are aligned with those in the bracket, and bolt the transceiver into place using the supplied short screws and flat washers. Mobile Power Connections To minimize voltage drop and avoid blowing the vehicles fuses, connect the supplied DC power cable directly to the battery terminals. Do not attempt to defeat or bypass the DC cables fuse - it is there to protect you, your transceiver, and your vehicles electrical system. 6 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Warning!
Never apply AC power to the power cable of the FT-2800M, nor DC voltage greater than 15.8 Volts. When replacing the fuse, only use a 15-A fuse. Failure to observe these safety precautions will void the Limited Warranty on this product.
Before connecting the transceiver, check the voltage at the battery terminals while revving the engine. If the voltage exceeds 15 Volts, adjust the vehicles voltage regulator before proceeding with installation.
Connect the RED power cable lead to the POSITIVE (+) battery terminal, and the BLACK power cable lead to the NEGATIVE () terminal. If you need to extend the power cable, use #12 AWG or larger insulated, stranded copper wire. Solder the splice connections carefully, and wrap the connections thoroughly with insulating electrical tape.
Before connecting the cable to the transceiver, verify the voltage and polarity of the voltage at the transceiver end of the DC cable using a DC voltmeter. Now connect the transceiver to the DC cable. Mobile Speakers The optional MSL-100 External Speaker includes its own swivel-type mounting bracket, and is available from your Yaesu dealer. Other external speakers may be used with the FT-2800M, if they present the specified 8-Ohm impedance and are capable of handling the 3.5 Watts of audio output supplied by the FT-2800M. Base Station Installation The FT-2800M is ideal for base station use as well as in mobile installations. The FT-
2800M is specifically designed to integrate into your station easily, using the information to follow as a reference. AC Power Supplies Operation of the FT-2800M from an AC line requires a power source capable of providing at least 15 Amps continuously at 13.8 Volts DC. The FP-1023 and FP-1030A AC Power Supplies are available from your Yaesu dealer to satisfy these requirements. Other well-regulated power supplies may be used, as well, if they meet the above voltage and current specifications. 7 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Use the DC power cable supplied with your transceiver for making power connections to the power supply. Connect the RED power cable lead to the POSITIVE (+) power supply terminal, and connect the BLACK power cable lead to the NEGATIVE () power supply terminal. 1. VOL Knob Front Panel Controls & Switches This control adjusts the audio volume level. Clockwise rotation increases the volume level. 2. SQL Knob This control is used to silence background noise on the receiver. It should be advanced clockwise just to the point where the noise is silenced (and the BUSY indicator on the display turns off), so as to provide the best sensitivity to weak signals. 3. Microphone Jack 4. Connect the supplied MH-48A6J Hand Microphone to this jack.
[%] Key This key allows operating the Internet Connection feature. 5. PWR Key 6. 7. 8. Press and hold this key for one second to toggle the transceivers power on and off.
[MHz(SET)] Key This key allows tuning in 1-MHz steps (the MHz digits will blink on the display). If receiving on a memory, pressing this key the first time activates the Memory Tuning mode, and pressing it again enables 1-MHz steps. Press and hold this key for one second to activate the Set (Menu) mode.
[REV(DW)] Key During split-frequency operation, such as through a repeater, this key reverses the transmit and receive frequencies. Press and hold this key for one seconds to activate the Dual Watch feature, described in the Operation chapter (PRI will be displayed on the LCD, indicating Priority Channel monitoring).
[LOW(A/N)] Key Press this key momentarily to select the transmitter power output level. The available power levels are:
8 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL HIGH(60W) MID(25W) LOW2(10W) LOW1(5W) While receiving on a memory, press and hold this key for one seconds to toggle the display between indication of the frequency and the channels Alpha/Numeric label. 9.
[D/MR(MW)] Key Press this key momentarily to switch the frequency control among the VFO, Memory System, and Home channel. Press and hold this key for one second to activate the Memory Storage mode. 10. DIAL Knob This 24-position detented rotary switch is used for tuning, memory selection and most function settings. The microphone UP/DWN buttons duplicate the functions of this knob. 11. Display The main digits on the display may show operating frequency, memory name, or any of many parameters during setting. Microphone Switches 1. PTT Switch Press this switch to transmit, and release it to receive. 2. Keypad 3. These 16 keys generate DTMF tones during transmission. In the receive mode, these 16 keys can be used for direct frequency entry and/or direct numeric recall of the Memory channels.
[P1]/[P2]/[P3]/[P4] Buttons
[P1] button (SQL OFF) Pressing this button disable the noise and tone squelch system.
[P2] button (S SRCH) Press this button to activate the Smart Search feature.
[P3] button (T SRCH) Press this button to activate the Tone Search feature.
[P4] button Press this button to recall the Weather broadcast channel bank. You can reprogram the [P1], [P2], [P3], and [P4] buttons for other functions, if desired. See page ?? for details. 4. LAMP Switch 9 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL This switch illuminates the Microphone keypad. 5. LOCK Switch 6. This switch locks out the Microphone buttons (except for the keypad and PTT switch).
[UP]/[DWN] Button Press (or hold in) either of these buttons to tune (or scan up or down) the operating frequency or through the memory channels. In many ways, these buttons emulate the function of the (rotary) DIAL knob. 1. EXT SP Jack Rear Panel Connectors This 2-contact mini 3.5-mm mini phone jacks provide receiver audio output for an optional external speaker. The audio impedance is 4-ohm, and the level varies according to the setting of the front panels VOL control. Inserting a plug into this jack disable audio from the transceivers internal speaker. 2. 13.8V DC Cable Pigtail w/Fuse This is the power supply connection for the transceiver. Use the supplied DC cable to connect this pigtail to the car battery or other DC power supply capable of at least 10 Amperes (continuous duty). Make certain that the red lead connects to the positive side of the supply. The fuse is 15-A. 3. ANT Coaxial Socket Connect a 144-MHz antenna to this type-M (SO-239) socket using 50-ohm coaxial cable and a type-M (pl-259) plug. Male sure the antenna is designed specifically for use on the operating frequency. Basic Operation R. F. Says: Hi! Im R. F. Radio, and Ill be helping you along as you learn the many features of the FT-2800M. I know youre anxious to get on the air, but I encourage you to read Basic Operation section of this manual as thoroughly as possible, so youll get the most out of this fantastic new transceiver. Now. lets get operating!
Turning the Transceiver On and Off 1. To turn the transceiver on, press and hold in the PWR key for one second. When you turn on the FT-2800M, the current DC supply voltage is indicated on the 10 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL LCD for 2 seconds. After this interval, the display will switch its normal indication of the operating frequency. 2. To turn the transceiver off, again press and hold in the PWR key for one second. Adjusting the Audio Volume Level Rotate the VOL control to adjust the receiver volume. Clockwise rotation increases the audio output level. Adjusting the Squelch Setting Rotate the SQL control just to the point where the noise is silenced and the BUSY indicator on the display turns off. If the SQL control is set further clockwise, sensitivity to weak signals is reduced. A special RF Squelch feature is provided on this radio. This feature allows you to set the squelch so that only signals exceeding a certain S-meter level will open the squelch. See page ?? for details Frequency Navigation 1) Tuning Dial Rotating the DIAL knob allows tuning in the pre-programmed steps. Clockwise rotation of the DIAL knob causes the FT-2800M to be tuned toward a higher frequency, while counter-clockwise rotation will lower the operating frequency. Press the [MHz(SET)] key momentarily, then rotate the DIAL knob, to change the frequency steps to 1 MHz per step. This feature is extremely useful for making rapid frequency excursions over the wide tuning range of the FT-2800M. 2) Direct Keypad Frequency Entry The keypad of the MH-48A6J DTMF Microphone may be used for direct entry of the operating frequency. To enter a frequency from the MH-48A6J keypad, just press the numbered digits in the proper sequence. There is no decimal point key on the MH-48A6J keypad. However, there is a short-cut for frequencies ending in zero - press the [#] key after the last non-
zero digit. Examples: To enter 146.520 MHz, press [1] [4] [6] [5] [2] [0]
11 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL To enter 146.000 MHz, press [1] [4] [6] [#]
3) Scanning From the VFO mode, press the microphones [UP]/[DWN] keys momentarily to initiate scanning toward a higher- or lower frequency, respectively. The FT-2800M will stop when it receives a signal strong enough to break through the squelch threshold. The FT-2800M will then hold on that frequency according to the setting of the Resume mode (Menu #23 (SCAN); see page ??). If you wish to reverse the direction of the scan (i.e. toward a lower frequency, instead of a higher frequency), just rotate the DIAL knob one click in the counter-clockwise direction while the FT-2800M is scanning. The scanning direction will be reversed. To revert to scanning toward a higher frequency once more, rotate the DIAL knob one click clockwise. Press the [UP]/[DWN] keys again to cancel scanning. Transmission To transmit, simply close the PTT (Push To Talk) switch on the microphone when the frequency is clear. Hold the microphone approximately 1 (25 mm) from your mouth, and speak into the microphone in a normal voice level. When your transmission is complete, release the PTT switch; the transceiver will revert . During transmission, the TX indicator will appear at the upper left corner on the display. Changing the Transmitter Power Level You can select from among a total of four transmit power levels on your FT-2800M. To change the power level, press the [LOW(A/N)] key (or microphones [A] key) to select one of four power settings. These power levels will be stored, in memory registers, at the time of memory storage (see page ?? for details on Memory operation). During transmission, the Bar Graph will deflect in the display, according to the power output selected. Weather Broadcast Reception The FT-2800M includes a unique feature which allows reception of weather broadcasts Advanced Operation 12 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL in the 160-MHz frequency range. Ten standard Weather Broadcast channels are pre-
loaded into a special memory bank. To listen to a Weather Broadcast Channel:
1. Press the Microphones [P4] button to recall the Weather Broadcast channels. 2. Turn the DIAL knob to select the desired Weather Broadcast channel. 3. If you wish to check the other channels for activity by scanning, just press the Microphones PTT switch. 4. To exit to normal operation, press the [P4] button again. Operation will return to the VFO or Memory channel you were operating on before you began Weather Broadcast operation. R.F. Says: In the event of extreme weather disturbances, such as storms and hurricanes, the NOAA (National Oceanic and Atmospheric Administration) sends a weather alert accompanied by a 1050 Hz tone and subsequent weather report on one of the NOAA weather channels. You may enable the this feature via Menu Item (32 W ALT), if desired. See page ?? for details. LOCK Feature To order to prevent accidental frequency change or inadvertent transmission, various aspects of the FT-2800Ms keys and knob may be locked out. The possible lockout combinations are:
KEY: Just the front panel keys are locked out DIAL: Just the front panel DIAL knob is locked out K+D: Both the keys and DIAL knob are locked out PTT: The PTT switch is locked (TX not possible) K+P: Both keys and PTT switch are locked out D+P: Both DIAL knob and PTT switch are locked out ALL: All of the above are locked out OFF: The Lock feature is disabled To lock out some or all of the keys:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 14 LOCK. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the display to OFF. 3. Press and hold the [MHz(SET)] key for one second to save your new setting and exit 13 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL to normal operation. When activate the locking feature, the KEY icon will appear on the LCD. Keypad Beeper A key/button beeper provides useful audible feedback whenever a key/button is pressed. If you want to turn the beeper off (or back on again):
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 03 BEEP. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the display to OFF. 3. Press and hold the [MHz(SET)] key for one second to save your new setting and exit to normal operation. Channel Step Selection Tuning steps are factory present to default increments which are appropriate for the country to which this radio is exported. To change to another step size as following:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 29 STEP. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired step size
(5/10/12.5/15/20/25/50/100 kHz). 3. Press and hold the [MHz(SET)] key for one second to save your new setting and exit to normal operation. Display Brightness The FT-2800M display illumination has been specially engineered to provide high visibility with minimal disruption of your night vision while you are driving. The brightness of the display is manually adjustable, using the following procedure:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 07 DIMR. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select a comfortable brightness level (1, 2, 3, and OFF). 3. Press and hold the [MHz(SET)] key for one second to save your new setting and exit to normal operation. 14 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL RF Squelch A special RF Squelch feature is provided on this radio. This feature allows you to set the squelch so that only signals exceeding a S-meter level will open the squelch. To set up the RF squelch circuit for operation, use the following procedure:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 20 RF SQL. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired signal strength level for the squelch threshold (1 - 10 or OFF). 3. Press and hold the [MHz(SET)] key for 1/2 second to save your new setting and exit to normal operation. Note: The receivers squelch will open based on the highest level set by the two squelch system Noise Squelch and RF Squelch). For example:
1) If the Noise Squelch (SQL control) is set so that signals at a level of S-3 will open the squelch, but the RF Squelch (Menu #20) is set to S-9, the squelch will only open on signals which are S-9 or stronger on the S-meter. If the RF Squelch is set to S-3, but the Noise Squelch is set to a high level which will only pass signals which are Full Scale on the S-meter, the squelch will only open on signals which are Full Scale on the S-meter. In this case, the Noise Squelch overrides the action of the RF Squelch. 2) The FT-2800M includes a host of convenience features which makes operation on amateur repeaters both efficient and enjoyable. Repeater Operation Repeater Splits This transceiver offers three methods of setting up split-frequency operation on repeaters:
[1] Manual selection of preset repeater shifts;
[2] Automatic Repeater Shift (ARS), providing automatic activation of repeater shifts during designated repeater frequency subbands; and
[3] Independently stored transmit and receive frequencies
(typically not corresponding to established repeater frequency shifts).
[1] Standard Repeater Shift To activate the standard shift manually, as following:
15 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 21 RPTR. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired shift direction (RPTR, +RPTR, or SIMP). 3. Press and hold the [MHz(SET)] key for one second to save your new setting and exit to normal operation. With repeater shift activated, you can temporarily reverse the transmit and receive frequencies by pressing the [REV(DW)] key (or microphones [B] key). Use this feature to display the transmit frequency without transmitting, and to check the strength of signals on a repeater uplink frequency (so as to determine whether or not a particular station is within Simplex range, for example). The repeater offset is fixed to 600 kHz from the factory. You can change the offset by following procedure, if needed:
1. Press and hold the [MHz(SET)] key for one second, then rotate the knob to select 24 SHIFT. 2. Press the [MHz(MHz)] key, then rotate the DIAL knob to set the desired offset. Note that the resolution of the standard repeater shift is to the nearest 50 kHz multiple. 3. Press and hold the [MHz(SET)] key for one second to save your new setting and exit to normal operation.
[2] Automatic Repeater Shift The ARS (Automatic Repeater Shift) feature in this transceiver allows easy and convenient repeater operation by automatically activating the repeater shift function whenever you tune to a standard repeater sub band. The ARS function is preset at the factory to conform to the standards for the country to which it is exported. The ARS function is enabled at the factory. To disable it:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 02 ARS. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to change the display to OFF. 3. Press and hold the [MHz(SET)] key for one second to save your new setting and exit to normal operation. To enable the ARS function again, select to ON in step 2 above. 16 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL
[3] Separate Transmit Frequency Memories All memory channels can store independent receive and transmit frequencies, to accommodate occasional non-standard offsets with greater frequency resolution than is available using the standard shift feature. 1. First store the receive (repeater output) frequency. In the VFO mode, tune the transceiver to the desired receive frequency. Now press and hold the [D/MR(MW)]
key on the for one second. 2. Within five seconds of pressing the [D/MR(MW)] key, use the DIAL knob or microphones [UP]/[DWN] buttons to select the desired memory for storage. 3. Now press the [D/MR(MW)] key momentarily to store the receive frequency into the selected memory. 4. Next store the transmit (repeater input) frequency. Since you are still in the VFO mode, tune the transceiver to the desired transmit frequency. 5. Now press and hold the [D/MR(MW)] key for one second. 6. Press and hold the PTT switch, and press the [D/MR(MW)] key momentarily while holding in the PTT switch. This will not cause transmission, but rather it will instruct the transceiver that you are programming a separate transmit frequency into memory. When you have finished the above procedure, press the [D/MR(MW)] key momentarily. The channel number and repeater downlink frequency will appears onto the display. If you press the PTT switch, you will observe the display changing to indicate the repeaters uplink frequency. Note also that the display shows + in the upper left-hand corner; this indicates that an odd (non-standard) shift has been stored on this channel. CTCSS/DCS Operation CTCSS Operation Many repeater systems require that a very-low-frequency audio tone be superimposed on your FM carrier in order to activate the repeater. This helps prevent false activation of the repeater by radar or spurious signals from other transmitters. This tone system, called CTCSS (Continuous Tone Coded Squelch System), is included in your FT-
2800M, and is very easy to activate. R. F. Says: CTCSS setup involves two actions: setting the Tone Mode and then setting of the Tone Frequency. These actions are set up by using the Set mode #28 (SQ TYP) and
#27 (SQ TNF). 17 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 28 SQ TYP. 2. Press the [MHz(SET)] key, then rotate the DIAL knob so that T ENC appears on the display; this activates the CTCSS Encoder, which allows repeater access. R. F. Says: You may notice an additional DC ENC and DCS appearing while you rotate the DIAL knob in this step. Well discuss the Digital Code Squelch system shortly. 3. Rotating the DIAL knob one more click clockwise in above step will cause TSQ to appear. When TSQ appears, this means that the Tone Squelch system is active, which mutes your FT-2800Ms receiver until it receives a call from another radio sending out a matching CTCSS tone. This can help keep your radio quiet until a specific call is received, which may be helpful while operating in congested areas. 4. When you have made your selection of the CTCSS tone mode, press the [MHz(SET)]
key momentarily, then rotate the DIAL knob one click counter-clockwise to select Menu #27 (SQ TNF). This Menu selection allows setting of the CTCSS tone frequency to be used. 5. Press the [MHz(SET)] key to enable adjustment of the CTCSS frequency. 6. Rotate the DIAL knob until the display indicates the Tone Frequency you need to be using. 7. When you have made your selection, press and hold the Press the [MHz(SET)] key for one second to save the new setting and exit to normal operation. R. F. Says: Your repeater may or may not re-transmit a CTCSS tone - some systems just use CTCSS to control access to the repeater, but dont pass it along when transmitting. If the S-Meter deflects, but the FT-2800M is not passing audio, repeat steps 1 through 3 above, but rotate the DIAL knob so that T ENC appears - this will allow you to hear all traffic on the channel being received. DCS Operation Another form of tone access control is Digital Code Squelch, or DCS. It is a newer, more advanced tone system which generally provides more immunity from false paging than does CTCSS. The DCS Encoder/Decoder is built into your FT-2800M, and operation is very similar to that just described for CTCSS. Your repeater system may be configured for DCS; if not, it is frequently quite useful in Simplex operation if your friend(s) use transceivers equipped with this advanced feature. R. F. Says: Just as in CTCSS operation, DCS requires that you set the Tone Mode to DCS and that you select a Tone Code. 18 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 28 SQ TYP. 2. Press the [MHz(SET)] key, then rotate the DIAL knob until DCS appears on the display; this activates the DCS Encoder/Decoder. 3. Now, press the [MHz(SET)] key momentarily, then rotate the DIAL knob to select Menu #26 (SQ DCS). 4. Press the [MHz(SET)] key momentarily to enable the adjustment of the DCS code. 5. Rotate the DIAL knob to select the desired DCS Code (a three-digit number). 6. When you have made your selection, press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. R. F. Says: Remember that the DCS is an Encode/Decode system, so your receiver will remain muted until a matching DCS code is received on an incoming transmission. Switch the DCS off when youre just tuning around the band!
Tone Search Scanning In operating situations where you dont know the CTCSS or DCS tone being used by another station or stations, you can command the radio to listen to the incoming signal and scan in search of the tone being used. Two things must be remembered in this regard:
You must be sure that your repeater uses the same tone type (CTCSS vs. DCS).
Some repeaters do not pass the CTCSS tone; you may have to listen to the station(s) transmitting on the repeater uplink (input) frequency in order to allow Tone Search Scanning to work. To scan for the tone in use:
1. Set the radio up for either CTCSS or DCS Decoder operation (see the previous discussion). In the case of CTCSS, TSQ will appear on the display; in the case of DCS, DCS will appear on the display. 2. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select Menu #27 (SQ TNF) when CTCSS is selected, or Menu #26 (SQ DCS) during DCS operation. 3. Press the Microphones [P3] key momentarily to start scanning for the incoming CTCSS or DCS tone/code. 4. When the radio detects the correct tone or code, it will halt on that tone/code, and audio will be allowed to pass. 5. Press and hold the [MHz(SET)] key for one second to lock in that tone/code and exit 19 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL to normal operation. R. F. Says: If the Tone Scan feature does not detect a tone or code, it will continue to scan indefinitely. When this happens, it may be that the other station is not sending any tone. You can press the Microphones [P3] key to halt the scan at any time. Tone Scanning works either in the VFO or Memory modes. CTCSS/DCS Bell Paging During CTCSS Decode or DCS operation, you may set up the FT-2800M such that a ringing bell sound alerts you to the fact that a call is coming in. Here is the procedure for activating the CTCSS/DCS Bell:
1. Set the transceiver up for CTCSS Decode (Tone Squelch) or DCS operation, as described previously. 2. Adjust the operating frequency to the desired channel. 3. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 04 BELL. 4. Rotate the DIAL konb to set the desired number of rings of the Bell. The available choices are 1, 3, 5, or 8 rings, REPEAT (continuous ringing), or OFF. 5. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. When you are called by a station whose transceiver is sending a CTCSS tone or DCS code which matches that set into your Decoder, the Bell will ring in accordance to this programming. DTMF Autodialer Operation Nine DTMF Autodialer memories are available on this radio. These DTMF Autodialer memories can store up to 16 digits of a telephone number for repeater autopatch or other use. To load DTMF Autodialer memories, use following procedure:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 10 DT MEM. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the DTMF Autodialer memory channel number into which you wish store a telephone number
(DTMF-1 to DTMF-9). 20 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 3. Press the [D/MR(MW)] key momentarily, then rotate the DIAL knob to select the first digit of the telephone number you wish to store. 4. When you have selected the correct digit, press the [REV(DW)] key momentarily. Now, rotate the DIAL knob to select the second of 16 available numbers in the current DTMF Autodialer memory resistor. 5. Repeat this procedure for each digit in the telephone number. If you a mistake, press the microphones [DWN] key to move back to the first digit, then re-enter the correct number. 6. When entry of all digits is complete, press the [MHz(SET)] key. 7. 8. Press and hold the [MHz(SET)] key for one second to save the new setting and exit If you wish to store another DTMF string, repeat steps 2 through 6 above. to normal operation. To transmit the memorized telephone number, use the following procedure:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 08 DTMF. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to set the DTMF Autodialer memory function to the ON position (the Telephone icon will appear). 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit 4. to normal operation. In the Autodialer function mode, first press the PTT switch, the press the microphones numeric key ([1] through [9]) corresponding to the DTMF memory string you wish to send. Once the string begins, you may release the PTT switch, as the transmitter will be held on the air until the DTMF string is completed. To disable the Autodialer function mode, select OFF in step 2 above. The speed at which the DTMF digits are sent can be changed. Two speed levels are available: Low (10 digits per second) and High (20 digits per second: default). To toggle between Low and High speed, use the following procedure:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 11 DT SPD. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired speed
(50: High speed or 100: Low speed). 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. 21 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL You can also set a longer delay between the time your transmitter is keyed and the first DTMF digit is send. To set a delay time, use the following procedure:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 09 DT DLY. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired speed
(50/250/450/750/1000 ms). 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. Memory Operation Memory Storage To store a frequency into memory:
1. In the VFO mode, select the desired frequency, repeater shift, CTCSS/DCS tone, and TX power level. 2. Press and hold the [D/MR(MW)] key for one second. A memory number will appear blinking in the display. 3. Within five seconds of pressing the [D/MR(MW)] key, use the DIAL knob to select the desired memory for storage. 4. Press the [D/MR(MW)] key again, this time momentarily, to store the displayed data into the selected memory channel slot. The memory label will disappear (since you are still operating in the VFO mode). Storing Independent Transmit Frequencies (Odd Splits):
1. Store the receiving frequency using the method already described. 2. Turn to the desired transmit frequency, the press and hold [D/MR(MW)] key for one second. 3. Within five seconds of pressing the [D/MR(MW)] key, use the DIAL knob to select the same memory channel number as used in step 1 above. 4. Press and hold in the PTT switch, then press the [D/MR(MW)] key momentarily while holding the PTT switch to save the entry and exit to normal operation. This will not cause transmission; instead, it signals the microprocessor that a separate transmit frequency is being programmed into that memory register. R. F. Says: Whenever you recall a memory which contains independently-stored transmit and receive frequencies, the + indication will appear in the display. 22 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Memory Recall 1. Press the [D/MR(MW)] key, repeatedly if necessary, until MR icon and memory channel number appears on the display; this indicates that the memory channel is recalled (Memory Mode). 2. When more than one memory has been stored, use the DIAL knob to select a memory for operation. Alternatively, microphones [UP] or [DWN] button may be used to stop or scan through the available memories. When using the microphones buttons, press and release the button to move one step up or down; press and hold the [UP] or [DWN] button for one second to begin memory scanning. Memory Recall from the Microphones keypad:
While operating on the Memory Recall mode, the keypad of the MH-48A6J Microphone may be used for direct recall of memory channels. To do this, press the Channel Number you wish to recall, then press the [] key. For example, to recall Memory Channel 5, press [5] []. To recall Memory Channel 118, press [1] [1] [8] []. Labeling Memories You may wish to append an alpha-numeric Tag (label) to a memory or memories, to aid in recollection of the channels use (such as club name, etc.). This is easily accomplished using the Menu mode. 1. Recall the memory channel on which you wish to append a label. 2. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 00 ALPH. 3. Press the [MHz(SET)] key. You will notice the first entrys place blink. Within the A/N entry mode, rotate the DIAL knob to select characters, and pressing the
[REV(DW)] key to move the characters entry place to the right. 4. Rotate the DIAL knob to select the desired number, letter, or symbol, then press the
[D/MR] key to move the next characters place. 5. Do this as necessary to complete a name tag (up to six characters) for your memory, then press the [MHz(SET)] key momentarily to save the A/N name entry. 6. Press and hold the [MHz(SET)] key for one second to exit to normal operation. While operating on the Memory Recall mode, press and hold the [LOW(A/N)] key for one seconds to toggle the display between indication of the frequency and the channels Alpha/Numeric label. 23 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Memory Tuning Once you have recalled a particular memory channel, you may easily tune off that channel, as though you were in the VFO mode. 1. With the FT-2800M in the Memory Recall mode, select the desired memory channel. 2. Press the [MHz(SET)] key momentarily. The MR indicator will be blinks; this indicates that the Memory Tuning. 3. Rotate the DIAL knob, as desired, to tune to anew frequency. The synthesizer steps 4. 5. for VFO operation will be the steps used during Memory Tuning. IF you wish to return to the original memory frequency, press the [D/MR(MW)] key momentarily. The MR indicator will be stop the blinking. If you wish to store a new frequency set during Memory Tuning, just press and hold in the [D/MR(MW)] key for one second, per normal memory storage procedure. Deleting Memories With 219 total memories available, there frequently are situations where you may desire to delete certain memories temporarily (except the Memory Channel 1). The procedure for deleting a channel is quite simple:
1. Press and hold the [D/MR(MW)] key for one second, then rotate the DIAL knob to select the memory channel on which you wish to be deleted. 2. Press the [LOW(A/N)] key momentarily. The CLEAR will be appear on the display. 3. Press again the [LOW(A/N)] key momentarily. This will cause the display to shift to Memory Channel 00, and the previously-selected memory will be deleted. Important Note: Once deleted, channel data cannot be recovered. Home Channel Memory A Convenient one-touch Home channel memory is available to simplify return to your most-often-used frequency. This memory do not appear in the regular memory banks, simplify operation. To recall the Home channel, just press the [D/MR(MW)] key repeatedly, if necessary, until HM icon appears on the display; this indicates that the Home Channel is recalled. The factory default frequency for the Home channel is 144.000 MHz. You can re-
program the Home channel in a manner identical to that used for the regular memories:
24 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 1. From the VFO mode, tune in the frequency you wish to store, and set all repeater shifts and other data just the way you do for normal memory channel storage. 2. Press and hold the [D/MR] key for one second, then press the [REV(DW)] key to store the displayed data into the Home channel. The memory label will disappear
(since you are still operating in the VFO mode). You may also append an alpha-numeric Tag (label) to a Home channel, described previously. Memory-Only Mode Once memory channel programming has been completed, you may place the radio in a Memory Only mode, whereby VFO and Home Channel operation are impossible. This may be particularly useful during public-service events where a number of operators may be using the radio for first time, and ultimate simplicity of channel selection is desired. To place the radio into the Memory Only mode, turn it off. Now press and hold in the
[MHz(SET)] and [D/MR(MW)] keys while turning the radio on. The VFO and Home Channel will now be disabled. To return to normal operation, repeat the above power-on procedure. The FT-2800Ms scanning capability provides the operator with many convenient methods of rapid frequency navigation. Scanning Basic Scanner Operation Before activating the scanner, make sure that the Squelch is set to silence the background noise when no signal is present. Scanning may be started or stopped using the microphones [UP] or [DWN] button. The following techniques are used for scanning:
Press and hold either the [UP] or [DWN] button for one second in the VFO mode will causes upward or downward band scanning, respectively, to begin.
Press and hold either the [UP] or [DWN] button for one second in the Memory mode will causes memory channel scanning toward a higher- or lower-numbered memory channel, respectively.
Scanning pauses when a signal opens the squelch, and the decimal point on the 25 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL display will blink. You can choose one of three scan-resume modes (described later).
To holt the scan manually, the easiest way is to push the PTT switch on the microphone momentarily (no transmission will occur while you are scanning). The scan may also be halted manually by pressing the microphones [UP] or [DWN]
button, or the [D/MR(MW)] key. Scan-Resume Options Three scan-resume modes are available on the radio:
In the BUSY mode, the scanner will remain halted for as long as there is carrier present on the channel; after the carrier drops at the end of the other stations transmission, the scanner will resume. In the HOLD mode, the scanner will halt on a signal it encounters. It will not restart automatically; you must manually re-initiate scanning if you wish to resume. In the 5 SEC mode, the scanner will halt for five seconds only, after which scanning will resume (whether or not the other station is still transmission).
To change the scan-resume mode, as following:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 23 SCAN. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired scan-
resume mode (BUSY/HOLD/5 SEC). 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. Memory Skip Scanning When you have some continuously-active channels in memories, you may wish to skip them for scanning, but still have them available for manual selection. To mask a memory to be skipped during scanning, as following:
1. Set the radio to memory mode by pressing the [D/MR(MW)] key repeatedly, if necessary. 2. Rotate the DIAL knob to select the Memory Channel to be skipped during scanning. 3. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 25 SKIP. 26 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 4. Press the [MHz(SET)] key, then rotate the DIAL knob so as to select SKIP. The current Memory Channel will now be ignored during scanning. The ONLY selection is used for Preferential Memory Scan, described in the next column. 5. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. A SKIP icon will appear when you recall the skipped memory channel manually. To re-institute a channel into the scanning loop, select OFF in step 4 above (the Skipped channel will, of course, still be accessible via manual channel selection methods using the DIAL knob in the Memory mode, whether or not it is locked out of the scanning loop). Preferential Memory Scan The FT-2800M also allows you to set up a Preferential Scan List of channels which you can flag within the memory system. These channels are designated by a blinking SKIP icon when you have selected them, one by one, for the Preferential Scan List. When you initiate memory scanning, beginning on a channel with the Blinking SKIP icon appended, only those channels bearing the Blinking SKIP icon will be scanned. If you initiate scanning on a channel which does not have the Blinking SKIP icon appended, you will scan all channels including those with the Blinking SKIP icon appended. Here is the procedure for setting up and using the Preferential Scan List:
1. Set the radio to memory mode by pressing the [D/MR(MW)] key repeatedly, if necessary. 2. Rotate the DIAL knob to select the Memory Channel which you wish to add to the Preferential Scan List. 3. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 25 SKIP. 4. Press the [MHz(SET)] key, then rotate the DIAL knob so as to select ONLY. 5. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. To initiate Preferential Memory Scan:
1. Set the radio to memory mode by pressing the [D/MR(MW)] key repeatedly, if necessary. 2. Rotate the DIAL knob to select any memory channel which has a Blinking SKIP 27 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL icon appended to the channel number. 3. Press and hold either the microphones [UP] or [DWN] button for one second to initiate Preferential Memory Scanning. Only the channels which have a Blinking SKIP icon appended to the channel number will be scanned. Programmable Band-Scan Limits Besides band and memory scanning, this radio can be set to tune or scan only the frequencies between user-defined lower and upper limits. For example, you may wish to limit tuning/scanning to 144.5 - 148.0 MHz, to avoid encroachment on the SSB/CW sub-band between 144.0 and 144.5 MHz These scanning limits are stores in special Sub-Band Limit Memories labeled L0/U0 through L9/U9, with L and U designations representing the Lower and Upper limit, respectively. To utilize this feature, use the following steps:
1. Store the lower edge of the desired scanning/tuning range in memory L0, and the upper edge in memory U0 (or, alternatively, in memories L1/U1 through L9/U9). 2. With any of these memories recalled, press the [MHz(SET)] key momentarily to activate the Programmable Band-Scan Limits. The PMS icon will be appeared. Tuning and scanning will now be limited within the just-programmed range. To cancel the Sub-Band Limits and return to normal memory operation, press the
[D/MR(MW)] key momentarily. Priority Channel Scanning (Dual Watch) The FT-2800Ms scanning features include a two-channel scanning capability which allows you to operate on a VFO, Memory channel or Home channel, while periodically checking a user-defined Memory Channel for activity. If a station is received on the Memory Channel which is strong enough to open the Squelch, the scanner will pause on that station in accordance with the Scan-Resume mode set via Menu mode 23 SCAN. See page xx. Here is the procedure for activating Priority Channel Dual Watch operation:
1. Set the radio to memory mode by pressing the [D/MR(MW)] key repeatedly, if necessary. 2. Press and hold in the [D/MR(MW)] key for one second (blink the Memory Channel 28 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Number), then select the memory channel you wish to be the Priority channel. 3. Press and hold in the [D/MR(MW)] key for one second. The P icon will appear to the upper left of the MR icon, indicating it is the Priority channel. 4. Now set the FT-2800M for operation on another memory channel, Home channel, or on a VFO frequency. 5. Press and hold the [REV(DW)] key for one second. The display will remain on the VFO, memory channel selected, or Home channel, but every five seconds the FT-
2800M will check the Priority Channel for activity. Priority Revert Mode During Priority channel operation (Dual Watch), a special feature is available which will allow you to move to the Priority Channel instantly, without waiting for activity to appear on the Priority Channel. When this feature is enabled, and priority monitoring is engaged, just press the microphones PTT switch. Operation will instantly revert to the Priority Channel. To enable Priority Revert operation:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 22 RVRT. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select ON. 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. To disable Priority Revert operation, select OFF in step 2 above. Band Edge Beeper The FT-2800M will automatically beep when a band edge is encountered during scanning (either in standard VFO scanning or during PMS operation). You may enable this feature (band edge beeper) when the frequency reaches the band edge while selecting the VFO frequency by the DIALknob. The procedure for enabling the Band-Edge Beeper is:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 12 EDG BP. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to set this Menu to ON. 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. 29 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Smart Search Operation The Smart Search feature allows you to load frequencies automatically according to where activity is encountered by your radio. When Smart Search is engaged, the transceiver will search above and below your current frequency, storing active frequencies as it goes (without stopping on them even momentarily); these frequencies are stored into a special Smart Search memory band, consisting of 31 memories (15 above the current frequency, 15 below the current frequency, plus the current frequency itself). Two basic operating modes for Smart Search are available:
SINGLE: In this mode, the transceiver will sweep the current band once in each direction starting on the current frequency. All channels where activity is present will be loaded into the Smart Search memories; whether or not all 31 memories are filled, the search will stop after one sweep in each direction. CONT: In this mode, the transceiver will make one pass in each direction as with One-Shot searching; if all 31 channels are not filled after the first sweep, however, the radio will continue sweeping until they are all filled. Setting the Smart Search Mode 1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 30 S SRCH. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired Smart Search mode (see above). 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. Storing Smart Search Memories 1. Set the radio to the VFO mode. Be sure that you have the Squelch adjusted properly (so that band noise is quieted). 2. Press the Microphones [P2] key to enter the Smart Search mode. The S.S icon will be appears at the left bottom corner of the display. 3. Press the Microphones [A] key to begin Smart Search scanning. 4. As active channels are detected, you will observe the number of loaded channels increasing in the regular memory channel window. 5. Depending on the mode you set for Smart Search operation (SINGLE or CONT), the Smart Search scan will eventually terminate, and the LCD will revert to Smart 30 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Search Memory Channel C. 6. To recall the Smart Search memories, rotate the DIAL knob to choose from among the Smart Search memories. 7. To return to normal operation, press the [D/MR(MW)] key. R.F. Says: Smart Search is a great tool when visiting a city for the first time. You dont need to spend hours looking up repeater frequencies from a reference guidebookjust ask your FT-2800M where the action is!
Internet Connection Feature The FT-2800M can be used to access the repeater which provide the Vertex Standard WIRESTM (Wide-Coverage Internet Repeater Enhancement System). 1. Press the [%] key to activate the Internet Connection feature. The int icon will appear in the memory channel field. 2. Rotate the DIAL, while pressing and holding in the [%] key, to select the access number corresponding to the WIRESTM repeater to which you wish to establish an Internet link (ask your repeater owner/operator if you dont know the access numbers in the network). 3. With the Internet Connection feature activated (as in step 1 above), the FT-2800M will generate a brief (0.2 second) DTMF tone according to your selection in step 2. This DTMF tone is sent at the beginning of every transmission to establish or maintain the link to the remote WIRESTM repeater. 4. To disable the Internet Connection feature, press the [%] key again. You may access other Internet Link Systems that use a DTMF string for access. 1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 10 DT MEM. 2. Press the [MHz(SET)] key momentarily, then load the DTMF tones which you wish to use to establish an Internet link (ask your repeater owner/operator if you dont know the access numbers in the network) into the desired DTMF Memory channel. 1). Rotate the DIAL knob to select the DTMF Autodialer memory channel number
(DTMF-1 through DTMF-9). 2). Press the [D/MR(MW)] key momentarily. 3). Rotate the DIAL knob to select the DTMF code, then press the [REV(DW)] key momentarily to move the digit. 31 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 4). Repeat step 3) above. 5). Press the [MHz(SET)] key momentarily to save the new setting. 3. Rotate the DIAL knob to select 13 INTNET. 4. Press the [MHz(SET)] key momentarily, then rotate the DIAL knob to set this Item to IRLP (to enable the alternative Internet Link, and disable the WIRESTM access option). 5. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. 6. Press the [%] key momentarily to activate the Internet Link System. The int icon will then appear in the memory channel field while the Internet Link System access feature is engaged. 7. Rotate the DIAL knob, while pressing and holding in the [%] key, to select the DTMF access number (DTMF-1 ~ DTMF-9) corresponding to the Internet link repeater to which you wish to establish an Internet link. 8. With the Internet link feature activated (as in step 6 above), press the [%] key or microphones [P2] key to send out the DTMF tones according to your selection in step 7 (to establish the link to the Internet link repeater). 9. To disable the Internet link feature, press the [%] key again. R. F. Says: To return to WIRESTM, recall Menu 13 INTNET then set it to WIRES. Miscellaneous Setting Time-Out Timer The Time-Out Timer (TOT) feature is designed to force the transceiver into the receive mode after a present time period of continuous transmission (the default is 6 minutes). This feature prevents your transceiver from transmitting a dead carrier for a long period of time in the event that the microphone PTT switch is accidentally locked in the TX condition. The Time-Out Timers switch-to-receive time may be adjusted, in one minute increments, for any period between 1 and 60 minutes. To change the default (6 minutes) time setting as follows:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 31 TOT. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired interval
(between 1 and 60 minutes), or OFF. 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit 32 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL to normal operation. Automatic Power-Off The Automatic Power-Off (APO) feature will turn the radio completely off after a user-defined period of PTT or key/button inactivity. If you do not press any front panel keys or buttons, rotate the DIAL knob or use the microphones keys and buttons, or transmit, and so long as the transceiver is not scanning or engaged in priority monitoring, the radio will shut itself off after the specified time period. This feature is useful in minimizing battery drain in a mobile installation if you forget to turn the transceiver off when you leave your vehicle. To activate the APO feature as follows:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 01 APO. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the desired switch-
off time (between 1 and 12 hours), or OFF. 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. Programming the key assignment Default FT-2800M key functions have been assigned to Microphones [P1]/[P2]/[P3]/[P4]
buttons at the factory. These may be changed by the user, if you wish to make another function. To programming the function:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select the Menu Item to be configured (15 PRG P1, 16 PRG P2, 17 PRG P3, or 18 PRG P4). 2. Press the [MHz(SET)] key, then rotate the DIAL knob to select the function you wish to assign to the button you selected in the previous step. The available choices are:
DC IN: Indicates the current DC supply voltage DIMR:
WX CH:
INTKEY:
SKIP:
SQLOFF: Opens the Squelch to allow un-muted reception S SRCH:
33 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL TONE: Selects CTCSS frequency T SRCH:
T CALL: Activates 1750 Hz Tone Burst RPTR: Selects Repeater Shift direction 3. Press the [MHz(SET)] key momentarily to save the new setting, then rotate the DIAL knob to select another programmable button to modify, if desired, and repeat above steps. 4. Press and hold the [MHz(SET)] key for one second to exit to normal operation. FM Bandwidth & MIC Gain Control You can reduce the microphone input level and receiver bandwidth when operating on tightly-clustered frequencies (channel spacing of 12.5 or 15 kHz). This will reduce the transmitter and receiver deviation, thus minimizing interference to other users (and improving reception, as well). To configure for the narrower bandwidth, use the following procedure:
1. Press and hold the [MHz(SET)] key for one second, then rotate the DIAL knob to select 33 W/N DV. 2. Press the [MHz(SET)] key, then rotate the DIAL knob to change the display to NARROW. 3. Press and hold the [MHz(SET)] key for one second to save the new setting and exit to normal operation. Reset Procedure In some instances of erratic or unpredictable operation, the cause may be corruption of data in the microprocessor (due to static electricity, etc.). If this happens, resetting of the microprocessor may restore normal operation. Note that all memories will be erased if you do a complete microprocessor reset, as described below. Microprocessor Resetting To clear all memories and other settings to factory defaults:
1. Turn the radio off. 2. Press and hold in the [MHz(SET)], [REV(SET)], [LOW(A/N)] and [D/MR(MW)] keys while turning the radio on. The MASRST will be appears on the display. 3. Press the [D/MR(MW)] key momentarily to reset all settings to their factory defaults (press any other key to cancel the Reset procedure). 34 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Set Mode Resetting To reset the Set (Menu) mode settings to their factory defaults:
1. Turn the radio off. 2. Press and hold in the [REV(SET)], [LOW(A/N)] and [D/MR(MW)] keys while turning the radio on. The SETRST will be appears on the display. 3. Press the [D/MR(MW)] key momentarily to reset the Set (Menu) mode settings to their factory defaults (press any other key to cancel the Reset procedure). Cloning The FT-2800M includes a convenient Clone feature, which allows the memory and configuration data from one transceiver to be transferred to another FT-2800M. This can be particularly useful when configuring a number of transceivers for a public service operation. Here is the procedure for Cloning one radios data to another:
1. Turn both radios off. 2. Connect the user-constructed cloning cable between the MIC jacks of the two radios. 3. Press and hold in the [MHz(SET)], [LOW(A/N)] and [D/MR(MW)] keys while turning the radios on. Do this for both radios (the order of switch-on does not matter). TX RX will appear on the displays of both radios when the Clone mode is successfully activated in this step. 4. On the Destination radio, press the [D/MR(MW)] key (???? will appear on the LCD). 5. Press the [MHz(SET)] key on the Source radio; ???? will appear on the Source 6. 7. radio, and the data from this radio will be transferred to the other radio. If there is a problem during the cloning process, ERROR will be displayed. Check your cable connections and battery voltage, and try again. If the data transfer is successful, ???? will reappear on both displays. Turn both radios off and disconnect the cloning cable. You can then turn the radios back on, and begin normal operation. The FT-2800M Set (Menu) mode, already described in parts of many previous chapters, is easy to activate and set. It may be used for configuration of a wide variety of Menu (Set) Mode 35 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL transceiver parameters, some of which have not been detailed previously. Use the following procedure to activate the Set (Menu) mode:
1. Press and hold the [MHz(SET)] key for one second to enter the Set mode. 2. Rotate the DIAL knob to select the Menu Item to be adjusted. 3. Press the [MHz(SET)] key momentarily to enable adjustment of the selected Menu item, then rotate the DIAL knob to perform the actual adjustment. 4. After completing your selection and adjustment, press and hold in the [MHz(SET)]
key for one second to exit the Set mode and exit to normal operation. Menu Selection Details 00 ALPH Function: Programming an Alpha/Numeric label for a memory. See page ?? for details. 01 APO Function: Enables/disables the Automatic Power Off feature. Available Values: 1H - 12 H, or OFF Default: OFF 02 ARS Function: Activates/deactivates the Automatic Repeater Shift feature. Available Values: ON/OFF Default: ON 03 BEEP Function: Enables/disables the key beeper. Available Values: ON/OFF Default: ON 04 BELL Function: Selects the CTCSS/DCS Bell Ringer repetitions. Available Values: 1, 3, 5, 8, REPEAT, or OFF Default: OFF 05 CK SFT Function: Shifting of CPU clock frequency. Available Values: ON/OFF 36 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Default: OFF This function is only used to move a spurious response birdie, shold it fall on a desired frequency. 06 DC IN Function: Indicate the Supply Voltage. 07 DIMR Function: Setting of the front panel displays illumination level. Available Values: 1, 2, 3, or OFF Default: 2 08 DTMF Function: Enables/disables the DTMF Autodialer. Available Values: ON/OFF Default: OFF 09 DT DLY Function: Setting of the DTMF Autodialer Delay Time. Available Values: 50/250/450/750/1000 (ms) Default: 450 (ms) 10 DT MEM Function: Loading of the DTMF Autodialer Memories. See page ?? for details. 11 DT SPD Function: Setting of the DTMF Autodialer Sending Speed. Available Values: 50/100 (ms) Default: 50 (ms) 12 EDG BP Function: Enables/disable the Band-edge beeper while scanning. Available Values: ON/OFF Default: ON 37 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 13 INTNET Function: Select the Internet Connection mode. Available Values: WIRES/IRLP Default: WIRES 14 LOCK Function: Select the Control Locking Lockout combination. Available Values: KEY/DIAL/K+D/PTT/K+P/D+P/ALL/OFF Default: OFF KEY: Just the front panel keys are locked out DIAL: Just the front panel DIAL knob is locked out K+D: Both the keys and DIAL knob are locked out PTT: The PTT switch is locked (TX not possible) K+P: Both keys and PTT switch are locked out D+P: Both DIAL knob and PTT switch are locked out ALL: All of the above are locked out OFF: The Lock feature is disabled 15 PRG P1 Function: Programming the function assigned to Microphones [P1] key. See page ?? for details. Available Values: SQLOFF/S SRCH/TONE/T SRCH/T CALL/RPTR/DC IN/DIMR/WX CH/INTKEY/SKIP Default: SQLOFF 16 PRG P2 Function: Programming the function assigned to Microphones [P2] key. See page ?? for details. Available Values: SQLOFF/S SRCH/TONE/T SRCH/T CALL/RPTR/DC IN/DIMR/WX CH/INTKEY/SKIP Default: S SRCH 17 PRG P3 Function: Programming the function assigned to Microphones [P3] key. See page ?? for details. Available Values: SQLOFF/S SRCH/TONE/T SRCH/T CALL/RPTR/DC IN/DIMR/WX 38 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL CH/INTKEY/SKIP Default: T SRCH 18 PRG P4 Function: Programming the function assigned to Microphones [P4] key. See page ?? for details. Available Values: SQLOFF/S SRCH/TONE/T SRCH/T CALL/RPTR/DC IN/DIMR/WX CH/INTKEY/SKIP Default: WX CH 19 REV HM Function: Select the Primary function of the [REV(DW)] key. Available Values: REV/HOME Default: REV REV: Pressing the [REV(DW)] key reverses the transmit and receive frequencies during repeater operation. HOME: Pressing the [REV(DW)] key instantly recalls a favorite Home channel. 20 RF SQL Function: Adjust the RF Squelch threshold level. Available Values: 1 - 10, or OFF Default: OFF 21 RPTR Function: Sets the Repeater Shift direction. Available Values: RPTR/+RPTR/SIMP Default: SIMP 22 RVRT Function: Enables/disables the Priority Channel Revert feature. Available Values: ON/OFF Default: OFF 23 SCAN Function: Select the Scan Resume mode. Available Values: BUSY/HOLD/5 SEC 39 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Default: BUSY BUSY: the scanner will remain halted for as long as there is carrier present on the channel; after the carrier drops at the end of the other stations transmission, the scanner will resume. HOLD: the scanner will halt on a signal it encounters. It will not restart automatically; you must manually re-initiate scanning if you wish to resume. 5 SEC: the scanner will halt for five seconds only, after which scanning will resume
(whether or not the other station is still transmission). 24 SHIFT Function: Set the magnitude of the Repeater Shift Available Values: 00.00 - 99.95 (MHz) (only shifts of less than 4 MHz will work) Default: 00.60 (MHz) 25 SKIP Function: Select the Memory Scan mode. Available Values: SKIP/ONLY/OFF Default: OFF SKIP: The Scanner will skip the flagged channels during scanning. ONLY: The scanner will only scan channels that are flagged (Preferential Scan List). OFF:
26 SQ DCS Function: Setting of the DCS code Available Values: 104 standard DCS codes. Default: 023 27 SQ TNF Function: Setting of the CTCSS Tone Frequency. Available Values: 50 standard CTCSS tones. Default: 67.0 (Hz) 28 SQ TYP Function: Selects the Tone Encoder and/or Decoder mode. Available Values: T ENC/TSQ/DC ENC/DCS/T+DCS/TSQ+DC/OFF 40 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL Default: OFF T ENC: CTCSS Encoder TSQ: CTCSS Encoder/Decoder DC ENC: DCS Encoder only DCS: Digital Code Squelch Encoder/Decoder T+DCS: Encodes a CTCSS tone and Decodes a DCS code TSQ+DC: Encodes a DCS tone and Decodes a CTCSS tone OFF 29 STEP Function: Sets the Synthesizer steps. Available Values: 5k/10k/12.5k/15k/20k/25k/50k/100k (Hz) Default: 5 k (Hz) 30 SSCRH Function: Selects the Smart Search Sweep mode. Available Values: SINGLE/CONT Default: SINGLE SINGLE: In this mode, the transceiver will sweep the current band once in each direction starting on the current frequency. All channels where activity is present will be loaded into the Smart Search memories; whether or not all 31 memories are filled, the search will stop after one sweep in each direction. CONT: In this mode, the transceiver will make one pass in each direction as with One-Shot searching; if all 31 channels are not filled after the first sweep, however, the radio will continue sweeping until they are all filled. 31 TOT Function: Sets the Time-Out Timer. Available Values: 1 MIN - 60 MIN, or OFF Default: 6 MIN 32 W ALT Function: Enables/disables the Weather Alert feature. Available Values: ON/OFF Default: OFF 41 Vertex Standard Co., Ltd. FCC ID: K66FT-2800M OPERATING MANUAL 33 W/N DV Function: Reducing the MIC gain (and Deviation) Available Values: WIDE/NARROW Default: WIDE 42 Vertex Standard Co., Ltd.
This product uses the FCC Data API but is not endorsed or certified by the FCC