| submitted | available | document details (if available) | source link |
|---|---|---|---|
| various | User Manual | Users Manual | 708.58 KiB |
AP-7532 Access Point INSTALLATION GUIDE 2 AP-7532 Access Point Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. 2015 Symbol Technologies, Inc. Installation Guide 3 1.0 Introduction . 5 1.1 Document Conventions . 5 1.2 Warnings . 6 1.3 Site Preparation . 6 1.4 AP-7532 Package Contents . 6 1.4.1 Features . 6 1.5 AP-7532 Antennas . 7 2.0 Hardware Installation . 9 2.1 Installation Instructions . 9 2.2 Precautions . 9 2.3 Access Point Placement . 10 2.4 Power Injector System . 10 2.5 Wall Mount Instructions . 12 2.5.1 Wall Mount Procedure - New Installation . 13 2.5.2 Wall Mount Procedure - Existing Access Point Replacement . 14 2.6 Suspended Ceiling T-Bar Mount Installation . 15 2.7 LED Indicators . 18 3.0 Basic Access Point Configuration . 20 4.0 AP-7532 Access Point Specifications . 31 4.1 Electrical Characteristics . 31 4.2 Physical Characteristics . 31 4.3 Radio Characteristics . 32 5.0 Regulatory Information . 33 5.1 Regulatory Information . 33 5.2 Wireless Device Country Approvals . 33 5.2.1 Country Selection . 34 5.2.2 Frequency of Operation - FCC and IC . 34 5.3 Health and Safety Recommendations . 35 5.3.1 Warnings for the use of Wireless Devices . 36 4 AP-7532 Access Point 5.3.2 Potentially Hazardous Atmospheres - Fixed Installations . 36 5.3.3 Safety in Hospitals . 36 5.4 RF Exposure Guidelines . 37 5.4.1 Safety Information . 37 5.4.2 International . 37 5.4.3 EU . 37 5.4.4 US and Canada . 37 5.5 Power Supply . 38 5.6 Radio Frequency Interference Requirements - FCC . 38 5.6.1 Radio Transmitters - Part 15 . 38 5.6.2 Radio Frequency Interference Requirements - Canada . 38 5.7 CE Marking and European Economic Area (EEA) . 39 5.8 Statement of Compliance . 40 5.9 Japan (VCCI) - Voluntary Control Council for Interference . 40 5.10 Korea Warning Statement for Class B ITE . 40 5.11 Other Countries. 40 5.12 Waste Electrical and Electronic Equipment (WEEE) . 41 5.13 Turkish WEEE Statement of Compliance . 42 6.0 Support . 43 7.0 Symbol Technologies End-User Software License Agreement . 44 8.0 AP-7532 Access Point China ROHS Compliance . 51 Installation Guide 1 Introduction 5 The AP-7532 external antenna and internal antenna Access Points are mid-tier Access Points with a relatively small footprint which supports functionality for dependable and efficient network performance.The AP-7532 is a 3x3:3 802.11ac Access Point utilizing one 2.4 GHz 802.11n radio and one 5 GHz 802.11ac radio. The Access Point housing is Plenum-rated (UL2043). The Access Points unique WiNG 5 software enables the Access Point to function as either a Standalone Access Point, an Adaptive Access Point, or a Virtual Controller. If new to Access Point technology, refer to the WiNG Access Point System Reference Guide to familiarize yourself with Access Point technology and the feature set supported by the WiNG operating system. The guide is available at www.zebra.com/support. This document is written for the qualified network device installer. 1.1 Document Conventions The following graphical alerts are used in this document to indicate notable situations:
NOTE Tips, hints, or special requirements that you should take note of.
!
CAUTION Care is required. Disregarding a caution can result in data loss or equipment malfunction. WARNING!
Indicates a condition or procedure that could result in personal injury or equipment damage. 6 1.2 Warnings AP-7532 Access Point
Read all installation instructions and site survey reports, and verify correct equipment installation before connecting the AP-7532 Access Point.
Remove jewelry and watches before installing this equipment.
Verify any device connected to this unit is properly wired and grounded.
Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications. 1.3 Site Preparation drops, and so on.
Consult your site survey and network analysis reports to determine specific equipment placement, power
Assign installation responsibility to the appropriate personnel.
Identify and document where all installed components are located.
Ensure adequate, dust-free ventilation to all installed equipment.
Identify and prepare Ethernet and console port connections.
Verify cable lengths are within the maximum allowable distances for optimal signal transmission. 1.4 AP-7532 Package Contents An AP-7532 Access Point is available in both external antenna (AP-7532) and internal antenna (AP-7532I) configurations. An AP-7532 ships with the following:
AP-7532 Access Point
AP-7532 Installation Guide (This Guide)
Wall mount screws and mounting bracket 1.4.1 Features An AP-7532 Access Point supports the following feature set:
Two RJ-45 connectors (GE1/POE and Console)
Two LED indicators
One 2.4 GHz 802.11n radio and one 5 GHz 802.11ac radio
3x3 MIMO, 3 spatial streams The GE1/POE accepts 802.3at or 802.3af compliant power from an external source. NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is recommended for Gigabit operation. Installation Guide 1.5 AP-7532 Antennas 7 1.5.1 AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - US An AP-7532 external antenna Access Point supports the following dual band antenna options for the US:
NOTE Per FCC requirement, the use of the Access Point on UNII-1 of 5GHz band requires installers to input antenna elevation gain during configuration if the AP placement is for outdoor coverage. This information can be found in Zebra antenna guide located at www.zebra.com/support.
*
Part Number Antenna Type ML-2452-APA2-01 ML-2452-HPA5-036 ML-2452-APAG2A1-01 Dipole Dipole Dipole ML-2452-PNL9M3-N36 Polarized -Panel ML-2452-PNA5-01R ML-2452-PTA3M3-036 ML-2452-VMM5M3-N72 Panel Patch Patch
* This antenna is for indoor placement only. 2.4 GHZ Gain (dBi) 5 GHZ Gain (dBi) 3.17 4.85 3 2.7 11 5.5 5 4.5 5 1.7 10.7 6 4 5.4 Elevation Gain for outdoor placement
(dBi) na*
na*
na*
7.3 5.2 na*
2.9 1.5.2 AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - EU
*An AP-7532 external antenna Access Point supports the following dual band antenna options for the EU:
Part Number Antenna Type ML-2452-APA2-01 ML-2452-HPA5-036 ML-2452-APAG2A1-01 ML-2452-HPAG4A6-01 ML-2452-HPA6-01 Dipole Dipole Dipole Dipole Dipole ML-2452-PNL6M3-N36 Polarized -Panel ML-2452-PNA5-01R ML-2452-PTA3M3-036 Panel Patch 2.4 GHZ Gain (dBi) 3.17 3 2.7 4 5.3 6 5.5 5 5 GHZ Gain (dBi) 4.85 5 1.7 7.3 6.1 6 6 4 8 AP-7532 Access Point Part Number Antenna Type ML-2452-VMM5M3-N72 Patch 2.4 GHZ Gain (dBi) 4.5 5 GHZ Gain (dBi) 5.4 1.5.3 AP-7532 Internal Antenna Model An AP-7532 internal antenna Access Point supports the following dual band antenna:
Antenna Type PIFA 2.4 GHZ Gain (dBi) 4.13 5 GHZ Gain (dBi) 5.92 1.5.4 AP-7532 Dual Band 2.4 GHz / 5 GHz Antennas - Canada
*An AP-7532 external antenna Access Point supports the following dual band antenna options for Canada:
Part Number Antenna Type ML-2452-APA2-01 ML-2452-HPA5-036 ML-2452-APAG2A1-01 Dipole Dipole Dipole ML-2452-PNL9M3-N36 Polarized -Panel ML-2452-PNA5-01R ML-2452-PTA3M3-036 ML-2452-VMM5M3-N72 Panel Patch Patch 2.4 GHZ Gain (dBi) 3.17 3 2.7 11 5.5 5 4.5 5 GHZ Gain (dBi) 4.85 5 1.7 10,7 6 4 5.4 Installation Guide 2 Hardware Installation 9 2.1 Installation Instructions An AP-7532 Access Point mounts either on a wall (with M 3.5 x 0.6 x 23 MM pan head screws and mounting bracket- or equivalent) or on a suspended ceiling T-bar. To prepare for the installation:
1. Match the part number on the purchase order with the part numbers in the packing list and on the case of the Access Point. 2. Verify the contents of the box include the intended AP-7532 Access Point, and the included hardware matches the package contents (see AP-7532 Package Contents on page 6). Part Number AP-7532-67040-US AP-7532-67040-WR AP-7532-67040-EU AP-7532-67030-US AP-7532-67030-WR AP-7532-67030-EU Description AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point external antenna US version AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point external antenna International version AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point external antenna EU version AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point internal antenna US version AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point internal antenna International version AP-7532 dual radio 802.11ac 3x3:3 MIMO Access Point internal antenna EU version 3. Review site survey and network analysis reports to determine the location and mounting position for the AP-7532 Access Point. 4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3at or 802.3af power source and run the cable to the installation site. Ensure there is sufficient slack on the cable to perform the installation steps. NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is recommended for Gigabit operation. 2.2 Precautions Before installing an AP-7532 Access Point, verify the following:
Your are using the correctly rated power solution for the AP-7532 (either the AP-PSBIAS-2P3-ATR power injector or the PWRS-14000-54R external power supply)
Do not to install the AP-7532 in wet or dusty areas.
Verify the environment has a continuous temperature range between -4 F to 104 F/-20 C to 40 C for external antenna Access Points and 32 F to 104 F/0 C to 40 C for internal antenna Access Points. 10 AP-7532 Access Point 2.3 Access Point Placement For optimal performance, install the Access Point away from transformers, heavy-duty motors, fluorescent lights, microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls or floors block transmission. Install the Access Point in an open area or add Access Points as needed to improve coverage. Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even placement of a light bulb) provides even, efficient coverage. Install the Access Point at an ideal height of 10 feet from the ground. To maximize the Access Points radio coverage area, recommends conducting a site survey to define and document radio interference obstacles before installing the Access Point. 2.4 Power Injector System An AP-7532 Access Point can receive power via an Ethernet cable connected to the GE1/POE (LAN) port. When users purchase a WLAN solution, they often need to place Access Points in obscure locations. In the past, a dedicated power source was required for each Access Point in addition to the Ethernet infrastructure. This often required an electrical contractor to install power drops at each Access Point location. The Power Injector merges power and Ethernet into one cable, reducing the burden of installation and allowing optimal Access Point placement in respect to the intended coverage area.
!
!
CAUTION Using a non-compliant injector, or an injector supporting legacy modes will not allow the AP-7532 to function at optimum performance levels. CAUTION Do not plug the AP-PSBIAS-2P3-ATR Power Injector into the Access Points Console port. Connecting the Power Injector into the console port can damage the port and void the AP-7532s product warranty. The AP-7532s supported Power Injector (Part No. AP-PSBIAS-2P3-ATR) is a high power POE Injector delivering up to 30 watts. The Access Point can only use a Power Injector when connecting the unit to the Access Points GE1/POE port. The Power Injector is separately ordered and not shipped with an existing AP SKU. Installation Guide 11 The Access Point Power Supply (Part No. PWRS-14000-54R) is not included with the Access Point and is orderable separately as an accessory. If the Access Point is provided both POE power and PWRS-14000-54R power concurrently, the Access Point will source power from the PWRS-14000-54R supply only. Disconnecting the AC power from the PWRS-14000-54R causes the Access Point to re-boot before sourcing power from the POE power injector. If the AP is operating using injector supplied power, the AP will not automatically reboot if an AC adapter is connected. The Access Point continues to operate with power supplied from the AC adapter without change to the Access Point operating configuration. If using AC adapter supplied power and a change to the APs operating configuration is warranted, the Access Point needs to be manually rebooted by the customer.
!
CAUTION The Access Point supports any standards-based compliant power source. However, using the wrong solution (including a POE system used on a legacy Access Point) could either limit functionality or severely damage the Access Point and void the product warranty. A separate Power Injector is required for each AP-7532 Access Point comprising the network. 12 AP-7532 Access Point The Power Injector can be installed free standing, on an even horizontal surface or wall mounted using the power injectors wall mounting key holes. The following guidelines should be adhered to before cabling the Power Injector to an Ethernet source and an Access Point:
Do not block or cover airflow to the Power Injector.
Keep the Power Injector away from excessive heat, humidity, vibration and dust.
The Power Injector isnt a repeater, and does not amplify the Ethernet signal. For optimal performance, ensure the Power Injector is placed as close as possible to the data port.
!
!
CAUTION To avoid problematic performance and restarts, disable POE from a wired switch port connected to an Access Point if mid-span power sourcing equipment (PSE) is used between the two, regardless of the manufacturer of the switch. CAUTION Ensure AC power is supplied to the Power Injector using an AC cable with an appropriate ground connection approved for the country of operation. To install the Power Injector to an Ethernet data source and an Access Point:
1. Connect the Power Injector to an AC outlet (110VAC to 220VAC). 2. Connect an RJ-45 Ethernet cable between the Power Injector Data & Power Out connector and the Access Points GE1/POE port. 3. Connect an RJ-45 Ethernet cable between the network data supply (host) and the Power Injector Data In connector. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Injector receives power and is ready for device connection and operation as soon as AC power is applied. Refer to the Installation Guide shipped with the Power Injector for a description of the devices LEDs. 2.5 Wall Mount Instructions A wall mount deployment requires hanging the AP-7532 Access Point with the provided mounting bracket and two screws. The AP-7532 can be mounted on to any plaster, wood or cement wall surface using the provided mounting bracket. The hardware required to install the AP-7532 on a wall consists of:
Two wide-shoulder Phillips pan head self-tapping screws (M3.5 x 0.6 x 23 mm)
Mounting bracket Optional customer provided installation tools include:
Phillips head screw driver, or drill and drill bit Installation Guide 13 2.5.1 Wall Mount Procedure - New Installation This section describes a new AP-7532 installation with no previous Access Point existing on the intended wall surface. 1. 2. Mark the screw hole locations depending on the intended deployment orientation of the unit. Place the mounting bracket against the wall. NOTE When pre-drilling a hole the recommended hole size is 4mm (0.16in.). 3. At each point, drill a hole in the wall and attach the mounting bracket. Place the Access Point on the mounting bracket. 4. 5. Cable the Access Point using either the Power Injector solution (AP-PSBIAS-2P3-ATR) or the approved AP-7532 power supply (PWRS-14000-54R). 14 AP-7532 Access Point For Power Injector installations:
a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the Power Injector Data & Power Out connector and the Access Points GE1/POE port. b. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the c. Power Injector Data In connector. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Power Injector receives power as soon as AC power is applied. For standard power adapter (non Power Injector) and line cord installations:
a. Connect a RJ-45 Ethernet cable between the network data supply (host) and the Access Points GE1/POE port. Connect the power supply line cord to the power adapter. b. Verify the power adapter is correctly rated according to the country of operation. c. d. Attach the power adapter cable into the power connector on the Access Point. e. Attach the power supply line cord to a power supply. 6. Verify the Access Point is receiving power by observing the LEDs are lit or flashing. For more information on AP-7532 LED behavior, see LED Indicators on page 18. The Access Point is ready to configure. 7.
!
CAUTION If not using an AP-PSBIAS-2P3-ATR power injector, ensure only the AP-7532s designated power supply (PWRS-14000-54R) is used to supply power to the Access Point. Using an incorrectly rated power supply could damage the Access Point and void the product warranty. Do not actually connect to the power source until the cabling portion of the installation is complete. 2.5.2 Wall Mount Procedure - Existing Access Point Replacement An existing AP-7131 or AP-7131N Series Access Point installed on a wall can be replaced by an AP-7532. Simply remove the existing AP-7131 or AP-7131N and install the new provided mounting bracket for AP-7532 directly to the wall. The cabling procedure for such a replacement is as described in the previous section. Installation Guide 15 2.6 Suspended Ceiling T-Bar Mount Instructions Ceiling mount requires holding the AP-7532 up against a T-bar of a suspended ceiling grid and twisting the unit on to the T-bar. If deploying the AP-7532 on a sculpted ceiling T-Bar, the Access Point mounting kit (Part No. KT-135628-01) can optionally be used as well. 1. First install the mounting bracket on the T-bar then attach the mounting bracket using the mounting slots on the Access Point. 16 AP-7532 Access Point 2. Cable the Access Point using either the Power Injector solution (AP-PSBIAS-2P3-ATR) or the approved AP-7532 power supply (PWRS-14000-54R). For Power Injector installations:
a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the Power Injector Data In connector. b. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the Power Injector Data & Power Out c. connector and the Access Points GE1/POE port. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Power Injector receives power as soon as AC power is applied. For standard power adapter (non Power Injector) and line cord installations:
a. Connect a RJ-45 Ethernet cable between the network data supply (host) and the Access Points GE1/POE port. Connect the power supply line cord to the power adapter. b. Verify the power adapter is correctly rated according the country of operation. c. d. Attach the power adapter cable into the power connector on the Access Point. e. Attach the power supply line cord to a power supply.
!
3. CAUTION If not using an AP-PSBIAS-2P3-ATR power injector, ensure only the AP-7532s designated power supply (PWRS-14000-54R) is used to supply power to the Access Point. Using an incorrectly rated power supply could damage the Access Point and void the product warranty. Do not actually connect to the power source until the cabling portion of the installation is complete. Verify the unit has power by observing the LEDs. For more information on AP-7532 LED behavior, see LED Indicators on page 18. 4. Align the bottom of the ceiling T-bar with the back of the Access Point. 5. Orient the Access Point chassis by its length and the length of the ceiling T-bar. 6. 7. Rotate the Access Point chassis 45 degrees clockwise. Push the back of the Access Point chassis on to the bottom of the ceiling T-bar. Installation Guide 17 8. Rotate the Access Point chassis 45 degrees counter-clockwise. The clips click as they fasten to the T-bar. 9. The Access Point is ready to configure. 18 AP-7532 Access Point 2.7 LED Indicators The AP-7532 LED activity indicators are located on the front of the housing and are visible through the enclosure. Installation Guide 19 The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz 802.11ac (amber) radio and the 2.4 GHz 802.11n (green) radio. Task 5 GHz Activity LED (Amber) 2.4 GHz Activity LED (Green) Unconfigured Radio On On Normal Operation
If this radio band is enabled:
Blink at 5 second interval
If this radio band is disabled:
Off
If this radio band is enabled:
Blink at 5 second interval
If this radio band is disabled:
Off
If there is activity on this band:
Blink interval at 1 time per second
If there is activity on this band:
Blink interval at 1 time per second Firmware Update Locate AP Mode On Off LEDs blink in an alternating green, red and amber pattern using an irregular blink rate. This LED state in no way resembles normal operating conditions. LEDs blink in an alternating green, red and amber pattern using an irregular blink rate. This LED state in no way resembles normal operating conditions 20 AP-7532 Access Point 3 Basic Access Point Configuration Once the AP-7532 is installed and powered on, complete the following steps to get the Access Point up and running and access management functions:
1. The Access Points IP address is optimally provided using DHCP or from bottom of the Access Point itself
(if available). A zero config IP address can also be derived if DHCP resources are unavailable or the IP address is not listed on the bottom of the unit. Using zero config, the last two octets in the IP address are the decimal equivalent of the last two bytes in the Access Points hardcoded MAC address. For example:
MAC address - 00:C0:23:00:F0:0A Zero-config IP address - 169.254.240.10 To derive the Access Points IP address using its MAC address:
a. Open the Windows calculator by selecting Start > All Programs > Accessories > Calculator. This menu path may vary slightly depending on your version of Windows. b. With the Calculator displayed, select View > Scientific. Select the Hex radio button. c. Enter a hex byte of the Access Points MAC address. For example, F0. d. Select the Dec radio button. The calculator converts F0 into 240. Repeat this process for the last Access Point MAC address octet. 2. Point the Web browser to the Access Points IP address. The following login screen displays:
Enter the default username admin in the Username field. 3. Enter the default password admin123 in the Password field. 4. 5. Select the Login button to load the management interface. Installation Guide 21 If this is the first time the interface has been accessed, a screen displays prompting for the Access Points country code. 6. Select the Country Code specific to this Access Points deployment location. Selecting the correct country is central to legal operation. Each country has its own regulatory restrictions concerning electromagnetic emissions and the maximum RF signal strength that can be transmitted. Select Apply to implement the selected Country Code. SKU's only support certain countries (for example:
a US SKU only includes US, Guam, Puerto Rico, American Samoa, US Virgin Islands and Mariana Island). The Access Point automatically displays a Dashboard where users can assess network health and conduct a diagnostic review of Access Point performance. NOTE At some point in the Access Points initial setup, the default password should be changed to enhance the security of the Access Point managed network. Refer to the Configuration > Management screen to change the default password to a more secure password. 7. Expand the Configuration menu item and select Basic. 22 AP-7532 Access Point 8. Set the following Basic Configuration Settings for this Access Point:
AP Name - Provide an AP Name used as this Access Points network identifier. If setting this Access Point as a Virtual Controller, each Access Point managed by this Virtual Controller lists this Access Points AP Name as its own. The AP Name is a required parameter.
Country Code - If the Country Code was not set when the Access Point was initially powered on, set the country now to ensure the Access Points legal operation. The Access Points wireless capabilities are disabled until the required country code is set.
Virtual Controller -Select this option to define this Access Point as a Virtual Controller capable of managing and provisioning up to 24 Access Points of the same type. If selecting this Access Point as a Virtual Controller, those Access Points managed by this Virtual Controller will list this Access Points AP Name as its own. Only one Virtual Controller can be designated.
Timezone - Use the drop-down menu to specify the geographic timezone where the Access Point is deployed. Different geographic time zones have daylight savings clock adjustments, so specifying the timezone correctly is important to account for geographic time changes.
Date & Time - Set the date, hour and minute for the Access Points current system time. Specify whether the current time is in the AM or PM.
NTP Server - Optionally provide the IP address of a NTP server resource. Network Time Protocol (NTP) manages time and/or network clock synchronization within the Access Point managed network. NTP is a client/server implementation. Access Points (NTP clients) periodically synchronize their clock with a master clock (an NTP server). For example, an Access Point resets its clock to 07:04:59 upon reading a time of 07:04:59 from its designated NTP server. 9. Select Apply to implement the updates. Installation Guide 23 10. Expand the Configuration menu item and select WAN. 11. Refer to the WAN Settings field and set the following:
Enable - Select this option to allow a connection between the Access Point and a larger network or outside world through the WAN port. Disable this option to isolate the WAN connection. No connections to a larger network or Internet are possible. Clients cannot communicate beyond configured subnets. Both the physical Port used to connect to the WAN and the virtual Interface
(VLAN) are also listed and fixed.
DHCP Client - Select this option to enable DHCP for the Access Point WAN connection. This is useful, if the target network or Internet Service Provider (ISP) uses DHCP. DHCP is a protocol that includes mechanisms for IP address allocation and delivery of host-specific configuration parameters from a DHCP server to a host. Some of these parameters are IP address, network mask, and gateway. The WAN and LAN ports should not both be configured as DHCP clients.
Static IP - Select this option to bypass DHCP address allocation resources and manually set the IP address for the Access Points WAN connection. Manually provide the Access Points Static IP/Mask and Default Gateway.
PPPoE Settings - Optionally enable Point-to-Point Protocol over Ethernet (PPPoE) on the WAN network. If PPPoE is enabled, provide the required Auth Type, Login Name and Login Password. Server Name and Default Gateway are optional settings. PPP is a data-link protocol for dialup connections allowing an Access Point to use a broadband modem (DSL, cable modem, etc.) for access to high-speed data and broadband networks. Most DSL providers support (or deploy) the PPPoE protocol. PPPoE uses standard encryption, authentication, and compression as specified by the PPPoE protocol. PPPoE enables the Access Point to establish a point-to-point connection to an ISP over an existing Ethernet interface. 24 AP-7532 Access Point
Static IP / Mask - Specify an IP address for the WAN connection if using static address assignment for the WAN port. An IP address uses a series of four numbers defined in dot notation, for example, 190.188.12.1. Additionally, specify a Mask for the access points WAN connection. This number is available from the ISP for a DSL or cable-modem connection, or from an administrator if the Access Point connects to a larger network.
Primary/Secondary DNS/Default Gateway - If using a static IP or DHCP, enter the Primary and Secondary DNS server resources numerical IP address and Default Gateway. NOTE If segmenting traffic between the Access Points WAN and LAN, youll need to create a VLAN. Complete steps 13 and 14 to define the required VLAN. Otherwise, proceed to step 15. 12. Select Apply to implement the updates. 13. Expand the Configuration menu item and select Access Points. Each AP Name displays as a link that can be selected to update the configuration of that specific Access Point. Select a target AP Name link from amongst those displayed in the Access Points screen. Refer to the LAN IP Interface Settings field, and add a VLAN and Static IP as required for enabling DHCP
(within the Configuration > Services screen) for client IP address requests and ensuring routable traffic. Installation Guide 25 14. Select Apply to commit the updates to the selected Access Points configuration. 15. Expand the Configuration menu item and select Wireless. The Wireless screen displays fields where Radio Settings and Wireless LAN settings can be defined. Its recommended default radio settings remain as is for the Access Points basic setup. In respect to the Radio Settings, the professional installer should be aware of the following:
NOTE The above example includes a field for setting the antenna gain. This setting is only available for external antenna Access Points and does not display for internal antenna Access Points.
The Channels available for configuration are channels for which the product is approved in its selected country. The professional installer must ensure the product is set to operate under conditions, and on channels, approved by country regulations.
Selecting Smart as the Power setting automatically configures radio power to not exceed the maximum power allowed by the defined country. For static power settings, the professional installer must ensure the configured power levels are compliant with local and regional regulations. The county selected automatically limits the maximum output power that can be set.
For external antenna Access Points, configure the Antenna Gain based on the antenna used in the deployment. The set gain value should include the antenna gain, along with any additional components, such as extension cables used between the Access Point and the antenna. In respect to Wireless LAN settings, at minimum, a WLAN should be created providing some measure of security. 26 AP-7532 Access Point 16. To create a new WLAN, select + Add from the upper, left-hand side of the Wireless LAN field. 17. Set the following configuration attributes for the new WLAN:
Name - Provide a unique name for the WLAN as its network identifier. This is a required setting.
Enable - Select this setting to enable this WLAN within the Access Point managed network and provide some measure of data protection.
SSID - Specify the WLAN's SSID. The WLAN SSID is case sensitive and alphanumeric. SSID length should not exceed 32 characters. This is a required setting. Select Client-To-Client Communication to enable client interoperability within this WLAN. The default is disabled, meaning clients are not allowed to exchange packets with other clients. It does not necessarily prevent clients on other WLANs from sending packets to this WLAN, but if this setting is disabled on the other WLAN, clients are not permitted to interoperate at all.
WLAN Type - The screen displays with the Open option selected. Naming and saving such a policy
(as is) would provide no security and might only make sense in a network wherein no sensitive data is either transmitted or received. This default setting is not recommended. If selecting Secure-PSK, enter a WPA2 Key to password protect the WLAN. Define whether the key is entered in ASCII or HEX characters. Selecting Show to expose the key is not recommended. If selecting Secure-802.1x, provide an IP address (or hostname) and a shared secret (password) Installation Guide 27 used to access an external RADIUS server resource designated to validate user requests to the Access Points WLAN resources. Selecting Guest displays fields for captive portal Web page creation, and is beyond the scope of this basic Access Point configuration.
Band -Select the 2.4 GHz and/or 5 GHz radio bands supported by the Access Point and its connected client traffic. If this Access Point is designated as a Virtual Controller AP, both radio bands should be enabled.
VLAN - Use the spinner control to specify a VLAN from 1 - 4,094 for this WLAN. When a client associates with a WLAN, the client is assigned a VLAN by load balance distribution. Its recommended you do not use VLAN 1 with the WLAN if the WAN port has been enabled.
Description - Optionally enter a WLAN description to further describe the WLANs deployment objective. 18. Select Apply to commit the updates to the Access Points WLAN configuration. 19. Expand the Configuration menu item and select Services. 20. Select Enable DHCP Server to ensure the Access Point can provision IP addresses to requesting clients over the specified interface. NOTE A VLAN must be already configured and available to the DHCP server as a viable interface between the Access Point and requesting client. Refer to the LAN IP Interface Settings field (within the Edit Access Point screen), and add a VLAN. Select + Add and provide a starting and ending IP range of addresses that constitute a pool of addresses available to requesting clients. 28 AP-7532 Access Point 21. Select Apply to commit the updates to the Access Points DHCP configuration. 22. At this point, youre ready to connect to the network using the security restrictions applied to the newly created WLAN. Ensure the new secure WLAN has been enabled, and check whether a client is able to access the network. Installation Guide 29 4 AP-7532 Access Point Specifications 4.1 Electrical Characteristics An AP-7532 Access Point has the following electrical characteristics:
Operating Current &
Voltage 12VDC, 1.25A (AUX input voltage) 12VDC PWRS-14000-54R power supply 48VDC, 0.375A (POE) 802.3at AP-PSBIAS-2P3-ATR Power Injector 4.2 Physical Characteristics An AP-7532 Access Point has the following physical characteristics:
Dimensions Housing Weight Operating Temperature 7.1 in. L x 6.5 in. W x 1.6 in. H 180 mm L x 165 mm W x 41 mm H Plenum-rated housing (UL2043) 1.8 lbs/0.82 kg External antennas: -4 F to 104 F/-20 C to 40 C Internal antennas: 32 F to 104 F/0 C to 40 C Storage Temperature
-40 F to 158 F/-40 C to 70 C Operating Humidity 85% RH non-condensing Operating Altitude
(maximum) Storage Altitude
(maximum) Electrostatic Discharge 8,000 ft @ 28C 30,000 ft @ 12C External antennas: 12KV air, 6 KV contact Internal antenna: 15KV air, 8KV contact 30 AP-7532 Access Point 4.3 Radio Characteristics The AP-7532 Access Point has the following radio characteristics:
Data Rates Supported 802.11b/g: 1,2,5.5,11,6,9,12,18,24,36,48 and 54 Mbps 802.11a: 6,9,12,18,24,36,48, and 54 Mbps 802.11n: MCS 0-23 up to 450 Mbps 802.11ac: MCS 0-9 up to 1.3 Gbps Direct Sequence Spread Spectrum (DSSS) Orthogonal Frequency Division Multiplexing (OFDM) Spatial multiplexing (MIMO) IEEE 802.11a/b/g/n/ac 802.11d and 802.11i WPA2 WMM and WMM-UAPSD 1dB increments Wireless Medium Network Standards Transmit Power Adjustment Installation Guide 5 Regulatory Information 31 5.1 Regulatory Information This guide applies to the following Model Numbers: AP-7532, AP-7532I. Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following Website: www.zebra.com/support Any changes or modifications to Symbol equipment, not expressly approved by Zebra could void the user's authority to operate the equipment. Zebra devices are professionally installed, the Radio Frequency Output Power will not exceed the maximum allowable limit for the country of operation. Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could cause damage and may violate regulations. This device is only to be used with a Zebra Wireless Switch. Declared maximum operating temperature: 40C. 5.2 Wireless Device Country Approvals Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe 1 Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at:
www.zebra.com/doc Note: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Operation of the device without regulatory approval is illegal. 32 AP-7532 Access Point 5.2.1 Country Selection Select only the country in which you are using the device. Any other selection will make the operation of this device illegal. Some Access Points are specifically designed to operate in certain countries (Example; -US for the United States, -EU for the European Union). Country Roaming This device incorporates the International Roaming feature (IEEE802.11d) which will ensure the product operates on the correct channels for the particular country of use. 5.2.2 Frequency of Operation FCC and IC 5 GHz Only Industry Canada Statement:
Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. Avertissement: Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation l'intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., qu'ils ont la priorit) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 2.4 GHz Only The available channels for 802.11bg operation in the US are Channels 1 to 11. The range of channels is limited by firmware. Installation Guide 33 5.3 Health and Safety Recommendations Ergonomic Recommendations Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures Vehicle Installation RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. An air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result. Position your device within easy reach. Be able to access your device without removing your eyes from the road. Note: Connection to an alert device that will cause a vehicle horn to sound or lights to flash, on receipt of a call on public roads, is not permitted. IMPORTANT Before installing or using, check state and local laws regarding windshield mounting and use of equipment. For Safe installation
Do not put your phone in a location that obstructs the drivers vision or interferes with the operation of the Vehicle.
Do not cover an airbag. 34 AP-7532 Access Point Safety on the Road Do not take notes or use the device while driving. Jotting down a "to do" list or flipping through your address book takes attention away from your primary responsibility, driving safely. When driving a car, driving is your first responsibility - Give full attention to driving. Check the laws and regulations on the use of wireless devices in the areas where you drive. Always obey them. 5.3.1 Warnings for the use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. 5.3.2 Potentially Hazardous Atmospheres Fixed Installations You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders). 5.3.3 Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Persons with Pacemakers:
Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.
Should not carry the device in a breast pocket.
Should use the ear furthest from the pacemaker to minimize the potential for interference. If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device. Installation Guide 35 5.4 RF Exposure Guidelines 5.4.1 Safety Information Reducing RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied. 5.4.2 International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on International human exposure to electromagnetic fields refer to the Declaration of Conformity (DoC) at: www.zebra.com/doc. 5.4.3 EU Remote and Standalone Antenna Configurations To comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop of similar configurations must operate with a minimum separation distance of 20cm from all persons. 5.4.4 US and Canada Co-located statement To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filling. To satisfy US and Canadian RF exposure requirements, a transmitting device must operate with a minimum separation distance of 30cm or more from a person's body. Pour satisfaire aux exigences Amricaines et Canadiennes d'exposition aux radiofrquences, un dispositif de transmission doit fonctionner avec une distance de sparation minimale de 30cm ou plus de corps d'une personne. Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 30cm between the radiator and your body. NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 30cm de distance entre la source de rayonnement et votre corps. Remote and Standalone Antenna Configurations To comply with FCC RF exposure requirements, Antennas that are mounted externally must be professionally installed at a fixed location and operate with a minimum distance of 30cm from all persons. 36 AP-7532 Access Point To comply with FCC Antenna requirements, the Antenna must be adjusted such that the RF emission lobes are below 30 degrees elevation. 5.5 Power Supply This device must be powered from a 802.3af or 802.3at compliant power source which has been certified by the appropriate agencies, or by an approved UL LISTED ITE (IEC/EN 60950-1, LPS/SELV) power supply with electrical ratings: Output 12 Vdc, min 1.25 A or 48 Vdc min 0.375 A (POE), with a recommended ambient temperature greater than 40 degrees C. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous. 5.6 Radio Frequency Interference RequirementsFCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help. 5.6.1 Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 5.6.2 Radio Frequency Interference Requirements - Canada CAN ICES-3 (B)/NMB-3(B) Radio Transmitters For RLAN Devices:
The use of 5 GHz RLANs, for use in Canada, have the following restrictions:
Restricted Band 5.60 5.65 GHz This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Installation Guide 37 Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical specifications were met In accordance with the regulations of Industry Canada, this radio transmitter can operate with an antenna of a type and a maximum gain (or lower) approved for the transmitter by Industry Canada. With the aim of reducing the risk of radio interference to other users, the chosen antenna type and its gain should be selected so that the equivalent isotropically radiated power (e.i.r.p.) does not exceed the intensity necessary for the establishment of a satisfactory connection. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. In compliance with respective local regulatory law, AP software provides professional installers the option to configure the antenna type and antenna gain for approved antennas. This radio transmitter (AP-7532, AP-7532I) has been approved by Industry Canada to operate with the antenna types listed below and having a maximum gain allowable and the impedance required for each type of antenna. The antenna types not included in this list, or whose gain is higher than the maximum gain indicates, are strictly prohibited for the operation of the transmitter. Refer to AP-7532 Antennas on page 7 for a listing of the 2.4 GHz and 5 GHz antennas initially approved for use with AP-7532 and AP7532I Access Points. Le prsent metteur radio (AP-7532, AP-7532I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal et l'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. 5.7 CE Marking and European Economic Area (EEA) WARNING: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. The use of 2.4GHz RLANs, for use through the EEA, have the following restrictions:
Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz. 38 AP-7532 Access Point 5.8 Statement of Compliance Zebra hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from www.zebra.com/doc. 5.9 Japan (VCCI) - Voluntary Control Council for Interference Class B ITE 5.10 Korea Warning Statement for Class B ITE 5.11 Other Countries Australia Use of 5GHz RLANs in Australia is restricted in the following band 5.50 5.65GHz. Brazil Declaraes Regulamentares para AP-7532 - Brasil Nota: A marca de certificao se aplica ao Transceptor, modelo AP-7532. Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. Para maiores informaes sobre ANATEL consulte o site: www.anatel.gov.br. Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. Este produto est homologado pela Anatel, de acordo com os procedimentos regulamentados pela Resoluo n242/2000 e atende aos requisitos tcnicos aplicados, incluindo os limites de exposio da Taxa de Absoro Especfica referente a campos eltricos, magnticos e eletromagnticos de radiofrequncia, de acordo com as Resolues n 303/2002 e 533/2009. Este dispositivo est em conformidade com as diretrizes de exposio radiofrequncia quando posicionado pelo menos 25 centmetros de distncia do corpo. Para maiores informaes, consulte o site da Anatel. Installation Guide 39 Chile Este equipo cumple con la Resolucin No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnticas. China Mexico Restrict Frequency Range to: 2.450 2.4835 GHz. S. Korea Taiwan 5.25-5.35 Thailand 40 AP-7532 Access Point 5.12 Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee. Franais: Clients de l'Union Europenne: Tous les produits en fin de cycle de vie doivent tre retourns Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : www.zebra.com/weee. Espaol: Para clientes en la Unin Europea: todos los productos debern entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea ms informacin sobre cmo devolver un producto, visite:
www.zebra.com/weee.
: :
Zebra . , :
www.zebra.com/weee. Deutsch: Fr Kunden innerhalb der EU: Alle Produkte mssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurckgesandt werden. Informationen zur Rcksendung von Produkten finden Sie unter www.zebra.com/weee. Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalit di restituzione, visitare il seguente sito Web: www.zebra.com/weee. Portugus: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos Zebra para reciclagem. Para obter informaes sobre como devolver o produto, visite: www.zebra.com/weee. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg www.zebra.com/weee voor meer informatie over het terugzenden van producten. Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naley zwrci do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktw znajduj si na stronie internetowej www.zebra.com/weee. etina: Pro zkaznky z EU: Vechny produkty je nutn po skonen jejich ivotnosti vrtit spolenosti Zebra k recyklaci. Informace o zpsobu vrcen produktu najdete na webov strnce: www.zebra.com/weee. Eesti: EL klientidele: kik tooted tuleb nende eluea lppedes tagastada taaskasutamise eesmrgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta klastage palun aadressi: www.zebra.com/weee. Magyar: Az EU-ban vsrlknak: Minden tnkrement termket a Zebra vllalathoz kell eljuttatni jrahasznosts cljbl. A termk visszajuttatsnak mdjval kapcsolatos tudnivalkrt ltogasson el a www.zebra.com/weee weboldalra. Svenska: Fr kunder inom EU: Alla produkter som uppntt sin livslngd mste returneras till Zebra fr tervinning. Information om hur du returnerar produkten finns p www.zebra.com/weee. Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrtettvksi Zebra-yhtin, kun tuotetta ei en kytet. Listietoja tuotteen palauttamisesta on osoitteessa www.zebra.com/weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, nr de er udtjent. Ls oplysningerne om returnering af produkter p: www.zebra.com/weee.
: ..: , , Zebra . , www.zebra.com/weee . Malti: Gal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aar tal-ajja ta' l-uu taghom, iridu jiu rritornati gand Zebra gar-riikla. Gal aktar tagrif dwar kif gandek tirritorna l-prodott, jekk jogbok ur:
www.zebra.com/weee. Installation Guide 41 Romnesc: Pentru clienii din UE: Toate produsele, la sfritul duratei lor de funcionare, trebuie returnate la Zebra pentru reciclare. Pentru informaii despre returnarea produsului, accesai: www.zebra.com/weee. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Zebra za reciklao. Za informacije o vrailu izdelka obiite: www.zebra.com/weee. Slovenina: Pre zkaznkov z krajn EU: Vetky vrobky musia by po uplynut doby ich ivotnosti vrten spolonosti Zebra na recyklciu. Bliie informcie o vrten vrobkov njdete na: www.zebra.com/weee. Lietuvi: ES vartotojams: visi gaminiai, pasibaigus j eksploatacijos laikui, turi bti grinti utilizuoti kompanij Zebra. Daugiau informacijos, kaip grinti gamin, rasite: www.zebra.com/weee. Latvieu: ES klientiem: visi produkti pc to kalpoanas ma beigm ir jnogd atpaka Zebra otrreizjai prstrdei. Lai iegtu informciju par produktu nogdanu Zebra, ldzu, skatiet: www.zebra.com/weee. Trke: AB Mterileri iin: Kullanm sresi dolan tm rnler geri dntrme iin Zebra'ya iade edilmelidir. rnlerin nasl iade edilecei hakknda bilgi iin ltfen u adresi ziyaret edin: www.zebra.com/weee. 5.13 TURKISH WEEE Statement of Compliance EEE Ynetmeliine Uygundur 42 6 Support AP-7532 Access Point If you have a problem with your equipment, contact support for your region. Contact information is available at: www.zebra.com/support When contacting support, please provide the following information:
Serial number of the unit
Model number or product name
Software type and version number Support responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you purchased your product from a business partner, contact that business partner for support. Customer Support Web Sites The Support site, located at www.zebra.com/support provides information and online assistance including developer tools, software downloads, product manuals and online repair requests. Manuals www.zebra.com/support Installation Guide 43 7 Symbol Technologies End-User Software License Agreement This End-User Software License Agreement ("End-User License Agreement") is between Symbol Technologies Inc.
(herein "Symbol Technologies") and End-User Customer to whom Symbol Technologies' proprietary software or Symbol Technologies Products containing embedded, pre-loaded, or installed software ("Products") is made available. This End-User License Agreement contains the terms and conditions of the license Symbol Technologies is providing to End-User Customer, and End-User Customer's use of the Software and Documentation. By using, downloading or installing this software, you or the entity that you represent ("End-User Customer") are consenting to be bound by and are becoming a party to this End-User License Agreement. 1. DEFINITIONS Documentation means product and software documentation that specifies technical and performance features and capabilities, and the user, operation and training manuals for the Software (including all physical or electronic media upon which such information is provided). Open Source Software means software with either freely obtainable source code license for modification, or permission for free distribution. Open Source Software License means the terms or conditions under which the Open Source Software is licensed. Software (i) means proprietary software in object code format, and adaptations, translations, decompilations, disassemblies, emulations, or derivative works of such software; (ii) means any modifications, enhancements, new versions and new releases of the software provided by Symbol Technologies; and (iii) may contain items of software owned by a third party supplier. The term Software does not include any third party software provided under separate license or third party software not licensable under the terms of this Agreement. To the extent, if any, that there is a separate license agreement packaged with, or provided electronically with, a particular Product that becomes effective on an act of acceptance by the end user, then that agreement supersedes this End-User License Agreement as to the end use of that particular Product. 2. GRANT OF LICENSE 2.1 Subject to the provisions of this End-User License Agreement, Symbol Technologies grants to End-User Customer a personal, limited, non-transferable (except as provided in Section 4), and non-exclusive license under Symbol Technologies copyrights and confidential information embodied in the Software to use the Software, in object code form, and the Documentation solely in connection with End-User Customers use of the Products. This End-User License Agreement does not grant any rights to source code. 44 2.2 3.1 3.2 AP-7532 Access Point If the Software licensed under this End-User License Agreement contains or is derived from Open Source Software, the terms and conditions governing the use of such Open Source Software are in the Open Source Software Licenses of the copyright owner and not this End-User License Agreement. If there is a conflict between the terms and conditions of this End-User License Agreement and the terms and conditions of the Open Source Software Licenses governing End-User Customers use of the Open Source Software, the terms and conditions of the license grant of the applicable Open Source Software Licenses will take precedence over the license grants in this End-User License Agreement. If requested by End-User Customer, Symbol Technologies will use commercially reasonable efforts to: (i) determine whether any Open source Software is provided under this End-User License Agreement; (ii) identify the Open Source Software and provide End-User Customer a copy of the applicable Open Source Software License (or specify where that license may be found); and, (iii) provide End-User Customer a copy of the Open Source Software source code, without charge, if it is publicly available (although distribution fees may be applicable). 3. LIMITATIONS ON USE End-User Customer may use the Software only for End-User Customers internal business purposes and only in accordance with the Documentation. Any other use of the Software is strictly prohibited and will be deemed a breach of this End-User License Agreement. Without limiting the general nature of these restrictions, End-User Customer will not make the Software available for use by third parties on a time sharing, application service provider, or service bureau basis or for any other similar commercial rental or sharing arrangement. End-User Customer will not, and will not allow or enable any third party to: (i) reverse engineer, disassemble, peel components, decompile, reprogram or otherwise reduce the Software or any portion to a human perceptible form or otherwise attempt to recreate the source code; (ii) modify, adapt, create derivative works of, or merge the Software with other software; (iii) copy, reproduce, distribute, lend, or lease the Software or Documentation to any third party, grant any sublicense or other rights in the Software or Documentation to any third party, or take any action that would cause the Software or Documentation to be placed in the public domain; (iv) remove, or in any way alter or obscure, any copyright notice or other notice of Symbol Technologies proprietary rights; (v) provide, copy, transmit, disclose, divulge or make the Software or Documentation available to, or permit the use of the Software by any third party or on any machine except as expressly authorized by this Agreement; or (vi) use, or permit the use of, the Software in a manner that would result in the production of a copy of the Software solely by activating a machine containing the Software. End-User Customer may make one copy of Software to be used solely for archival, back-up, or disaster recovery purposes; provided that End-User Customer may not operate that copy of the Software at the same time as the original Software is being Installation Guide 45 3.3 3.4 4.1 5.1 operated. End-User Customer may make as many copies of the Documentation as it may reasonably require for the internal use of the Software. Unless otherwise authorized by Symbol Technologies in writing, End-User Customer will not, and will not enable or allow any third party to: (i) install a licensed copy of the Software on more than one unit of a Product; or (ii) copy onto or transfer Software installed in one unit of a Product onto another device. If End-User Customer is purchasing Products that require a site license, End-User Customer must purchase a copy of the applicable Software for each site at which End-User Customer uses such Software. End-User Customer may make one additional copy for each computer owned or controlled by End-User Customer at each such site. End-User Customer may temporarily use the Software on portable or laptop computers at other sites. End-User Customer must provide a written list of all sites where End-User Customer uses or intends to use the Software. 4. TRANSFERS End-User Customer will not transfer the Software or Documentation to any third party without Symbol Technologies prior written consent. Symbol Technologies consent may be withheld at its discretion and may be conditioned upon transferee paying all applicable license fees and agreeing to be bound by this End-User License Agreement. 5. OWNERSHIP AND TITLE Symbol Technologies, its licensors, and its suppliers retain all of their proprietary rights in any form in and to the Software and Documentation, including, but not limited to, all rights in patents, patent applications, inventions, copyrights, trademarks, trade secrets, trade names, and other proprietary rights in or relating to the Software and Documentation. No rights are granted to End-User Customer under this Agreement by implication, estoppel or otherwise, except for those rights which are expressly granted to End-User Customer in this End-User License Agreement. All intellectual property developed, originated, or prepared by Symbol Technologies in connection with providing the Software, Products, Documentation or related services remains vested exclusively in Symbol Technologies, and End-User Customer will not have any shared development or other intellectual property rights. 46 6.1 7.1 8.1 8.2 AP-7532 Access Point 6. CONFIDENTIALITY End-User Customer acknowledges that the Software contains valuable proprietary information and trade secrets and that unauthorized dissemination, distribution, modification, reverse engineering, disassembly or other improper use of the Software will result in irreparable harm to Symbol Technologies for which monetary damages would be inadequate. Accordingly, End-User Customer will limit access to the Software to those of its employees and agents who need to use the Software for End-User Customers internal business 7. MAINTENANCE AND SUPPORT No maintenance or support is provided under this End-User License Agreement. Maintenance or support, if available, will be provided under a separate Software maintenance and support agreement. 8. LIMITED WARRANTY AND LIMITATION OF LIABILITY Unless otherwise specified in the applicable warranty statement, the Documentation or in any other media at the time of shipment of the Software by Symbol Technologies, and for the warranty period specified therein, for the first 120 days after initial shipment of the Software to the End-User Customer, Symbol Technologies warrants that the Software, when installed and/or used properly, will be free from reproducible defects that materially vary from its published specifications. Symbol Technologies does not warrant that End-User Customers use of the Software or the Products will be uninterrupted or error-free or that the Software or the Products will meet End-User Customers particular requirements. SYMBOL TECHNOLOGIES TOTAL LIABILITY, AND END-USER CUSTOMERS SOLE REMEDY, FOR ANY BREACH OF THIS WARRANTY WILL BE LIMITED TO, AT SYMBOL TECHNOLOGIES OPTION, REPAIR OR REPLACEMENT OF THE SOFTWARE OR PAYMENT OF END-USER CUSTOMERS ACTUAL DAMAGES UP TO THE AMOUNT PAID TO SYMBOL TECHNOLOGIES FOR THE SOFTWARE OR THE INDIVIDUAL PRODUCT IN WHICH THE SOFTWARE IS EMBEDDED OR FOR WHICH IT WAS PROVIDED. THIS WARRANTY EXTENDS ONLY TO THE FIRST END-USER CUSTOMER; SUBSEQUENT TRANSFEREES MUST ACCEPT THE SOFTWARE AS IS AND WITH NO WARRANTIES OF ANY KIND. SYMBOL TECHNOLOGIES DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE. 8.3 IN NO EVENT WILL SYMBOL TECHNOLOGIES BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOSS OF USE, TIME OR DATA, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS, OR SAVINGS, TO THE FULL EXTENT SUCH MAY Installation Guide 47 BE DISCLAIMED BY LAW, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE LIMITATIONS IN THIS PARAGRAPH WILL APPLY NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY LIMITED REMEDY. 9. TERM AND TERMINATION 9.1 9.2 10.1 Any use of the Software, including but not limited to use on the Products, will constitute End-User Customers agreement to this End-User License Agreement. End-User Customers right to use the Software will continue for the life of the Products with which or for which the Software and Documentation have been provided by Symbol Technologies, unless End-User Customer breaches this End-User License Agreement, in which case this End-User License Agreement and End-User Customers right to use the Software and Documentation may be terminated immediately by Symbol Technologies. In addition, if Symbol Technologies reasonably believes that End-User Customer intends to breach this End-User License Agreement Symbol Technologies may, by notice to End-User Customer, terminate End-User Customers right to use the Software. Upon termination, Symbol Technologies will be entitled to immediate injunctive relief without proving damages and, unless End-User Customer is a sovereign government entity, Symbol Technologies will have the right to repossess all copies of the Software in End-User Customers possession. Within thirty
(30) days after termination of End-User Customers right to use the Software, End-User Customer must certify in writing to Symbol Technologies that all copies of such Software have been returned to Symbol Technologies or destroyed. 10. UNITED STATES GOVERNMENT LICENSING PROVISIONS This Section applies if End-User Customer is the United States Government or a United States Government agency. End-User Customers use, duplication or disclosure of the Software and Documentation under Symbol Technologies copyrights or trade secret rights is subject to the restrictions set forth in subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights clause at FAR 52.227-19 (JUNE 1987), if applicable, unless they are being provided to the Department of Defense. If the Software and Documentation are being provided to the Department of Defense, End-User Customers use, duplication, or disclosure of the Software and Documentation is subject to the restricted rights set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 (OCT 1988), if applicable. The Software and Documentation may or may not include a Restricted Rights notice, or other notice referring to this End-User License Agreement. The provisions of this End-User License Agreement will continue to apply, but only to the extent that they are 48 11.1 11.2 11.3 11.4 11.5 11.6 11.7 consistent with the rights provided to the End-User Customer under the provisions of the FAR and DFARS mentioned above, as applicable to the particular procuring agency and procurement transaction. AP-7532 Access Point 11. GENERAL Copyright Notices. The existence of a copyright notice on the Software will not be construed as an admission or presumption that public disclosure of the Software or any trade secrets associated with the Software has occurred. Compliance with Laws. End-User Customer acknowledges that the Software is subject to the laws and regulations of the United States and End-User Customer will comply with all applicable laws and regulations, including export laws and regulations of the United States. End-User Customer will not, without the prior authorization of Symbol Technologies and the appropriate governmental authority of the United States, in any form export or re-export, sell or resell, ship or reship, or divert, through direct or indirect means, any item or technical data or direct of indirect products sold or otherwise furnished to any person within any territory for which the United States Government or any of its agencies at the time of the action, requires an export license or other governmental approval. Violation of this provision is a material breach of this Agreement. Third Party Beneficiaries. This End-User License Agreement is entered into solely for the benefit of Symbol Technologies and End-User Customer. No third party has the right to make any claim or assert any right under this Agreement, and no third party is deemed a beneficiary of this End-User License Agreement. Notwithstanding the foregoing, any licensor or supplier of third party software included in the Software will be a direct and intended third party beneficiary of this End-User License Agreement. Waiver. No waiver of a right or remedy of a Party will constitute a waiver of another right or remedy of that Party. Assignments. Symbol Technologies may assign any of its rights or sub-contract any of its obligations under this End-User License Agreement or encumber or sell any of its rights in any Software, without prior notice to or consent of End-User Customer. Causes of Action. End-User Customer must bring any action under this End-User License Agreement within one year after the cause of action arises except that warranty claims must be brought within the applicable warranty period. Entire Agreement and Amendment. This End-User License Agreement contains the parties entire agreement regarding End-User Customers use of the Software and may be amended only in a writing signed by both parties, except that Symbol Technologies may modify this End-User License Agreement as necessary to comply with applicable laws and regulations. Installation Guide 49 11.8 11.8 Governing Law. This End-User License Agreement is governed by the laws of the the State of Delaware in the United States to the extent that they apply and otherwise by the internal substantive laws of the country to which the Software is shipped if End-User Customer is a sovereign governmental entity. The terms of the U.N. Convention on Contracts for the International Sale of Goods do not apply. In the event that the Uniform Computer information Transaction Act, any version of this Act, or a substantially similar law (collectively UCITA) becomes applicable to a Partys performance under this Agreement, UCITA does not govern any aspect of this End-User License Agreement or any license granted under this End-User License Agreement, or any of the parties rights or obligations under this End-User License Agreement. The governing law will be that in effect prior to the applicability of UCITA. Dispute Resolution. Unless End-User Customer is a sovereign governmental entity, any dispute arising from or in connection with this End-User License Agreement shall be submitted to the sole and exclusive forum of the state and federal courts sitting in New Castle County, Delaware (the "Delaware Courts"), and each Party irrevocably submits to the jurisdiction of the Delaware Courts for the litigation of such disputes. Each Party hereby irrevocably waives, and agrees not to assert in any suit, action or proceeding brought in the Delaware Courts, any claim or defense that the Party is not subject to the jurisdiction of the Delaware Courts, that the Delaware Courts are an inconvenient forum, or that the Delaware Courts are an improper venue. 50 8 AP-7532 Access Point China ROHS Compliance AP-7532 Access Point 15
(Parts)
(Metal Parts)
(Circuit Modules)
(Cables and Cable Assemblies)
(Plastic and Polymeric Parts)
(Optics and Optical Components)
(Batteries)
(Pb)
(Hg)
(Cd)
(Cr(VI)) X X X O O O O O O O O O O O O O O O O O O O O O
(PBB) O O O O O O
(PBDE) O O O O O O SJ/T 11364 O: GB/T 26572 X:GB/T 26572 (
This table was created to comply with China RoHS requirements for AP-7532 and AP-7532I Access Points. Installation Guide 51 52 AP-7532 Access Point Installation Guide 53 54 AP-7532 Access Point Installation Guide 55 56 AP-7532 Access Point Zebra Technologies Corporation Lincolnshire, IL 60069 USA Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. 2015 Symbol Technologies, Inc. MN002312A01 Revision A September 2015
This product uses the FCC Data API but is not endorsed or certified by the FCC