FCC ID: 2AWCN-Q6 Mobile phone

Model name:Q6 Manufacture:METELL TECHNOLOGY CO., LIMITED FCC Warning a 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. b 15.21 Changes or modification warning. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. c 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. dSpecific Absorption Rate (SAR) information:

This Mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. eFCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types:

Mobile phone (FCC ID: 2AWCN-Q6) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.187W/kg and when properly worn on the body is 0.576 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 1.0cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 1.0cm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. fBody-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10 mm must be maintained between the users body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

Label Mobile phone Model name: Q6 FCC ID: 2AWCN-Q6 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired The label size is 30mm * 20mm operation.

4G NET INC 2020.5.26 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, 4G NET INC hereby authorize (Shenzhen STS Test Services Co., Ltd.) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Name: Xue Xiang Lin Signature:

TCBJ FORM-4 Issued by: TCB Administrator Revision 6 12/06/10

Differences Description We 4G NET INC state:

Product Mobile phone Model Name Q6, Q6.3, Q6 PRO, Q6.3 PRO Brand Name UNIQCELL, UNIQ FCC ID: 2AWCN-Q6 The electrical circuit design, layout, components used and internal wiring for above models are identical, only different in model name, brand name. cameras and memory. Difference in Details Model Name Q6 Q6.3 Q6 PRO Q6.3 PRO Brand Name UNIQCELL, UNIQCELL, UNIQCELL, UNIQCELL, UNIQ UNIQ UNIQ UNIQ Camera 2Mp+ 8Mp 5Mp+ 13Mp 5Mp+8Mp 8Mp+16Mp Memory RAM(1GB)+

ROM(16GB) RAM(2GB)+

ROM(32GB) RAM(2GB)+

ROM(32GB) RAM(4GB)+

ROM(64GB) Signatory Date 2020-5-26 Signature Name: Xue Xiang Lin Title: Manager Company: 4G NET INC Address: 3000 NW 72 AVENUE MIAMI FL 33122

4G NET INC 2020.5.26 MET Laboratories, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (Mobile phone / Q6, Q6.3, Q6 PRO, Q6.3 PRO /FCC ID:

2AWCN-Q6) To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. required to be submitted with this application be permanently withheld from public review. Please contact me if there is any information you may need. Sincerely, Name: Xue Xiang Lin Signature:

Schematics Block diagram Operation description Tune up Procedure Part List TCBJ FORM-4 Issued by: TCB Administrator Revision 6 12/06/10

OPERATIONAL DESCRIPTION Model: Q6 Band: GSM850 PCS1900 WCDMA B2/B5 LTE Band B2/B4/B5/B7 1. Scope This document shows and provides the more detail information about the platform we used. The basic description for the Baseband and RF section are also included. 2. System Block Diagram Figure 1 System Overview 3. Modem Features CPCDTX in CELL_DCH,UL DRX DL DRX),HS-SCCH Compatible with GSM/GPRS Release 1999, DCS1800 and PCS1900 recommendations Dedicated GSM/GPRS signal processing engine for equalization, channel encoding/decoding for all traffic and control channels, GMSK modulation and encryption/decryption (A5/1, A5/2 and A5/3, GEA 1, GEA3 and GEA 3 algorithms) GMSK modulator with digital I and Q channel outputs Calibration mechanism of offset and gain mismatch for baseband A/D converters and D/A converters 10-bit D/A converter for Automatic Power Control Programmable radio Rx filter GSM system timing Complete in-phase and quadrature (I/Q) component interface between the Digital Signal Processor (DSP) and RF module Dedicated RF serial control interface and parallel control signals Programmable GSM/GPRS modem Packet switched data with CS1/CS2/CS3/CS4 coding schemes Multi-band support Complete voice band codec Integrated microphone bias GSM/GPRS quad vocoders for adaptive multirate (AMR), enhanced full rate (EFR), full rate

(FR) and half rate (HR) Five auxiliary analog inputs to a 10-bit analog-to-digital converter (ADC) for measurement purposes Support SAIC(single antenna interference cancellation) 4. Baseband(MT6737) Camera Interface Support 8 MP Image capture Support Video snapshot(up to 8M sensor),which enables user capture full size image while recording video Image capture resolution:Up to 13M Video Codec Support MPEG4 decoding, compliant with ISO/IEC 14496-simple profile.HVGA 30fps. Support MPEG4 ASP B frame decoding Support H263 decoding, compliant with ITU H.263 profile 0. HVGA 30fps. Support Flash video format. Audio Codec Wavetable synthesis with up to 64 tones Two differential microphone input with a 0~20 dB boost gain stage A programmable gain amplifier in front of ADC An analog stereo mixer with programmable gains to mix signals coming from DAC and the stereo line inputs (analog bypass path) A stereo programmable gain amplifier for headphone outputs Programmable sampling frequencies (Fs) for ADC and DAC: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, and 48 kHz 16-bit linear PCM voice data, programmable DAC/ADC, data buffer sizes from 1 to 160, support DMA Both ARM and DSP can control the audio codec 5. Connection Features FM Features Supporting frequency range of 76MHz ~ 108MHz 2-bits ADC DDFS for 100kHZ IF-signal down-conversion CORDIC - based FM detector Stereo decoder with weak signal processing Stereo Mono blending and auto selectivity Noise blanking De-emphasis filter can be configured with =50s (Europe and Japan) and =75s Soft/Hardware audio mute function Signal level detection for FM signal quality information AGC control feedback Frequency offset cancellation Bluetooth Features Compliant with Bluetooth4.0 +EDR specification Bluetooth Piconet and Scatternet support Receiver with -88dBm sensitivity Support BT-WIFI Co-existence with 3-wire/2-wire handshake Support AFH Low power consumption Hardware Version: V2.1 Software Version: UNIQ_CELL_1+16_Q6_C8EM_3M2_20200327 BLE Operation Frequency:2402~2480 MHz Modulation Type: GFSK Antenna Designation: PIFA Antenna Antenna Gain(Peak):1.49dBi BT4.0+EDR Operation Frequency:2402~2480 MHz Modulation Type:GFSK//4-DQPSK/8DPSK Antenna Designation:PIFA Antenna Antenna Gain(Peak):1.49dBi 2.4GWIFI Operation Frequency:

802.11b/g/n 20: 2412~2462 MHz 802.11n(40MHz):2422~2452MHz Modulation Type:

802.11b(DSSS):CCK,DQPSK,DBPSK 802.11g(OFDM):BPSK,QPSK,16-QAM,64-QAM 802.11n(OFDM):BPSK,QPSK,16-QAM,64-QAM Antenna Designation: PIFA Antenna Antenna Gain(Peak):1.49dBi GSM/WCDMA Tx Frequency:

GSM/GPRS/EDGE:

850: 824 MHz ~ 849MHz 1900: 1850 MHz ~ 1910MHz WCDMA:

Band V: 824 MHz ~ 849 MHz Band II: 1850 MHz ~ 1910 MHz Rx Frequency:

GSM/GPRS/EDGE:

850: 869 MHz ~ 894 MHz 1900: 1930 MHz ~ 1990MHz WCDMA:

Band V: 869 MHz ~ 894 MHz Band II: 1930 MHz ~ 1990 MHz Antenna: PIFA Antenna Antenna gain:

GSM 850: 1.77dBi ,PCS 1900: 2.11dBi WCDMA 850: 1.77dBi, WCDMA1900: 2.12dBi, LTE LTE Band 2:1850.7~1909.3MHz LTE Band 4:1710.7~1754.3MHz LTE Band 5:824.7~848.3MHz LTE Band 7:2502.5~2567.5MHz LTE:QPSK/16QAM Antenna: PIFA Antenna Antenna gain:

LTE Band 2: 2.05dBi LTE Band 4: 2.23dBi LTE Band 5: 1.95dBi LTE Band 7: 1.85dBi

Chip Declaration Letter We 4G NET INC state:

Product Mobile phone Model Name Q6, Q6.3, Q6 PRO, Q6.3 PRO FCC ID: 2AWCN-Q6 These requirements are met by way of the operation of the chip setup. 15.247 (g) and (h)

(g) Frequency hopping spread spectrum systems are not required to employ all available hopping channels during each transmission. However, the system, consisting of both the transmitter and the receiver, must be designed to comply with all of the regulations in this section should the transmitter be presented with a continuous data (or information) stream. In addition, a system employing short transmission bursts must comply with the definition of a frequency hopping system and must distribute its transmissions over the minimum number of hopping channels specified in this section.

(h) The incorporation of intelligence within a frequency hopping spread spectrum system that permits the system to recognize other users within the spectrum band so that it individually and independently chooses and adapts its hopsets to avoid hopping on occupied channels is permitted. The coordination of frequency hopping systems in any other manner for the express purpose of avoiding the simultaneous occupancy of individual hopping frequencies by multiple transmitters is not permitted. Signatory Date 2020-5-26 Signature Name: Xue Xiang Lin Title: Manager Company: 4G NET INC Address: 3000 NW 72 AVENUE MIAMI FL 33122