G6 Saver Users Guide 2.4G RF Dongle (Mouse) Model: RG-71M www.a4tech.com THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Federal Communications Commission Requirements The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient of relocate the receiving antenna.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
- 1 -
Introduction:
2.4GHz wireless technology with 16 channels and 1,048,576 ID Codes Errorless 2-Way Communication Technology The 2.4GHz RF wireless technology is fine-tuned with 16 selected Errorless 2-way communication technology features error channels and exclusive 1,048,576 ID-codes; it offers precise and correction capability that speeds up data transmission and smooth wireless operation in active wireless environments. It allows many wireless devices to operate simultaneously in one area without increases wireless precision. It saves valuable battery power and cost. interfering in the range up to 8-10 meters. Anti-interference with Auto Channel Hopping Technology Ultra Low Battery Power Consumption - Only 6mA!
"Auto Channel Hopping" technology automatically detects and 2.4G is designed with 4 Level Auto Power Saving modes with secures available channels in the busy public 2.4GHz universal band. It ensures better quality of wireless communication. ultra low battery power consumption, it only requires 6mA of electric current to operate. Ultra Low Battery Power Consumption - Only 6mA!
Say Goodbye To Double Click 2.4G is designed with 4-Level Auto Power Saving modes. With ultra low battery power consumption, it only requires 6mA of electric current to operate. Just one click on 2X Button directly opens files and programs, saves time and improves efficiency.
- 2 -
Specifications RF Data Transmit Rate ID Codes 2Mbps 1,048,576 sets Frequency Channels 2.402GHz2.480GHz 16 channels Wireless Range Any electrical device, such as the computer monitor, Zip drives, speakers, etc., can cause interference with the wireless mouse. Most likely, this will effect tracking of pointing devices or the range of the device. To make sure that your mouse transmits and receives properly, refer to the following instructions:
1. For optimal performance, place the receiver at least 8 inches (20 centimeters) away from other electrical devices, such as the computer monitor, Zip drives, speakersetc. 2. The effective distance of wireless mouse should be no farther than 26-33 feet (8 -10 meters). This will ensure optimal communication between the mouse and the USB receiver. Keep 8 inches
< 26-33 feet NOTE: You should always get at least a 4 meters range. If you find that your cordless device gets less than 4 meters range, please replace the batteries with a fresh set, perform the synchronization procedure for the mouse and test the range again. If the range is still below 4 feet, please test your device on another system, preferably in a different environment. If you find it gets the same range on another system, please contact A4 TECH support to obtain information about a warranty replacement. However, if the range improves on another system, then it may be an environmental variable. Use the suggestions above to resolve the environmental interference issue. Operating Warnings: For optimal performance and RF (Radio Frequency) reception:
1. Avoid using the wireless mouse on a metal desk or a desk with a metal frame can cause problems with pointing device behavior and range. 2. The mouse will enter a suspend mode at the same time your computer dose, click a button on the mouse presenter to activate it. 3. Never use the mouse on the glass or mirrored surface.
- 3 -
Hardware Installation Step 1: Inserting the Batteries A. Press the tab on the battery cover B. Insert the supplied batteries, making sure that the C. Slide the batter cover back into its locates on the mouse bottom as shown here and remove the cover. positive (+) and negative (-) ends of the battery match the polarity indicators inside the battery housing. position until it clicks firmly into place.
- 4 -
Step 2: Connect the Receiver A. For Notebook computer:
Insert the USB receiver into the USB port of your Notebook computer. A. For PC computer:
Insert the USB receiver into the USB port of desktop computer or via a USB HUB. B. The USB receiver will automatically be recognized by your computer. C. Press the connect button on the USB receiver as shown, the Green Power LED will light up, and starts Blinking. D. Immediately Press the connect button on the bottom of the mouse, If you cant find or see your cursor on the screen, follow the steps below: (If the mouse connected, you can try press any keys to try key working.) 1. Unplug and re-plug the receiver 2.Test the device on another USB port or computer. 3. Some surfaces may trick the optical sensor, such as reflective surfaces like glass or mirrors. The Optical sensor should perform well on all other surfaces. Power Management 1. To power on the mouse, press the connect button on the bottom of the mouse once. 2. To turn off the mouse, press and hold the connect button on the bottom of the mouse until its optical light (RED) turns off. Note: Removing the batteries will require you to synchronize it with the receiver again the next time you turn it back on.
- 5 -
Power on/off System Requirements To use the mouse presenter, your computer must meet the following hardware requirements and run one of the operating system listed below. Hardware IBM or Compatible PC Operating System Windows 2000, XP, MCE2005, XP (x64), 2003(x64), and VISTA x86 Package Includes 2.4GHz RF Mouse USB RF Receiver 2 AAA Alkaline Batteries CD (User Manual on CD) CD (User Manual on CD) Hard Disk Driver USB Port
** Please inform us if there is any discrepancy found in this manual. (Note: This manual may be revised without notice).
- 6 -