FWS-2275E3-A10-00 Federal Communications Commission Statement FCC warning This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by doing one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
Radiation Exposure Statement:
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Overview Designed to offer customers more choice and allow AAEON to respond more quickly to requests for customized systems, the FWS-2275 board and Virtual Customer Premise Equipment (vCPE) technology, Unified Threat Management
(UTM), Virtual Private Networking (VPN), Intrusion Detection and Prevention Systems (IDS, IPS), Firewall technology, and Load Balancing applications. The FWS-2275 is powered by an Intel Celeron Processor N3350 processor and has onboard LPDDR4 2GB memory and 16GB eMMC. Measuring only 115mm x 115mm x 44mm, the appliance is small enough for even the most crowded offices. Despite its modest dimensions, it still houses two USB3.0 ports and a console port alongside its three LAN ports. The system features an innovative housing design that allows the chassis to be removed by undoing a single screw. This user-friendly detail means any necessary maintenance work can be carried out quickly and easily Specification system Form Factor Processor Chipset Desktop Network Appliance Intel Celeron Processor N3350 SoC SoC System Memory Onboard LPDDR4 2133 ,2GB network Ethernet Bypass display Intel i211 GbE x 3 Graphics Controller Intel Integrated Connector storage HDD HDMI x 1 CF/CFast/mSATA Onboard 16GB eMMC internal/ expansion interface PCIe Slot Mini-PCIe Slot 1 x Mini-Card Full Size Slot with SIM Socket KB Mouse USB USB 3.0 x 2 Wifi miscellaneous RTC Onboard WiFi 802. 11 b/g/n 2X2, BT4. 1 Internal RTC Watchdog Timer 1~255 steps by software programmable TPM GPIO Fan MTBF (hours) Color
(TPM v1.2 9660/TPM2.0 9665 Optional) 4 bits input, 4bits output TBD Black Physical & Environmental SPEC Power Requirement 9~24V DC Power Operating Temperature 32F ~ 122F (0C ~ 50C ) Storage Temperature
-4F ~ 140F (-20C ~ 60C) Operating Humidity 10%~80% relative humidity, non-condensing Storage Humidity 10%~80% @40C; non-condensing Vibration Shock 0.5 Grms/ 5 ~ 500Hz / operation 1.5 Grms/ 5 ~ 500Hz / non operation 10 G peak acceleration (11 m sec. duration), operation 20 G peak acceleration (11 m sec. duration), non operation Dimension (W x D x H) 45.3 x45.3 x17.3 (115mm x 115mm x 44mm) i/o Front Panel USB3.0 Ports x 2 LEDs (3 x TOP Row, 2 x Bottom Row)x 6 Power Button with LED integrated x1 Micro-USB Console Port x1 Serial Port x1 GPIO 8 Bit x1 3 x 1GbE RJ45 Ports Rear Panel 1 x Power Input connector, non-lockable 1 x Reset button Outlook_ Rear side Outlook_ Front side Installation 1. Put the FWS-2275 on the table and find 3 network routes to connect the LAN port to the broadband sharer. 2. Set the internal IP of the sharer. Otherwise, the default value of the sharer can be used. Most of them are 192.168.11.X or 192.168.3.X. This X is the IP that is automatically assigned to each sharer. Note Most of the sharers use 192.168.X.1 as the IP of Gateway. 3. Consider the server to provide those services, the IP of the server (mostly the IP of 192.168.X.250), and the Port Number of these services. Install the server, connect the sharer, find the PC and connect to the sharer to determine the server. The service is normal. 4. Its WIFI and Bluetooth can also be used in communication.