Mini video outdoor station DANGER Dangerous currents flow through the body when coming into direct or indirect contact with live components. This can result in electric shock, burns or even death. Work improperly carried out on current-carrying parts can cause fires. Disconnect the mains voltage prior to mounting and dismantling!
Permit work on the 100 240 V mains network to be carried out only by specialist staff. Please read the mounting instructions carefully and keep them for future use. Additional user information and information about planning is available at http://new.abb.com/low-voltage/products/building-
automation/product-range/abb-welcome or by scanning the QR code. Intended use As a part of the ABB-Welcome IP system, this device can only be used with accessories from the system. Manufacturer ABB Genway Xiamen Electrical Equipment CO., LTD. Address: No.7 Fangshan South Road, Xiang An, Xiamen, Fujian, China Post Code: 361000 h s i l g n E
, 310 mA
, 350 mA 24 V 20-27 V 27 V 24 V Technical data Rating voltage Operating voltage range Rating current Operating temperature -40 C+55 C Product dimensions Camera type Camera viewing angle 104 Resolution ratio Power supply for door opener Floating output for door opener Video codec Audio codec IP level IK level Network connection standard
, 3 A
, 3 A 99 mm x 168 mm 26 mm (H8131.P.-.) 105 mm x 180 mm 43 mm (H8136.P.-.) CMOS
, 4 A impulse, max. 250 mA 0.3 M (640 x 480 pixel), 25fps 15 V holding 250 V 30 V H.264 G.711 IP 54 IK 07 IEEE802.3, 10/100 Mbps, auto MDI/MDI-X Operation Indicator flashes slowly: ringing Indicator flashes quickly: busy line Call indicator Unlock indicator Speaker and microphone integration Round pushbutton 1 2 3 4 5 For the operation of this device we recommend the extended product manual. (see QR code) Connection Door status detection interface Exit button interface Plug-in clamps (LOCK...AGND) for door opener Plug-in clamps (COM...NC...NO) for floating output Plug-in clamps (DC+...GND) for standalone power supply LAN (PoE) N/A 1 2 3 4 5 6 7 Video privacy Making and saving video recordings can infringe on personal rights! Always observe applicable legal and labeling requirements for placement and operation of video components!
EU declaration of conformity Hereby, ABB Genway, declares that this Mini outdoor station H8131 is in compliance with the essential requirements and other relevant provisions of RE Directive 2014/53/EU. The complete of the EU declaration of conformity is available by scanning the QR code. FCC ID: 2AEBL-H8131 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Only operate the device in accordance with the instructions supplied. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.