1Check the package contents Unpack the Bluetooth Headset and check that the following items are included:
OFF Bluetooth Headset Bluetooth A/V Transmitter or Bluetooth Audio Dongle or Bluetooth Audio Dongle or OFF USB Cable Audio Cable Quick Guide Power Adapter 2Charge the battery The battery lasts eight hours and is re-
charged using the power adapter or the USB cable. To recharge:
Plug the USB cable into the DC jack on the Bluetooth Headset and connect the other end to your PC. or Plug the power adapter into the DC jack on the Bluetooth Headset and connect the other end to an electrical outlet. Recharging takes 90 minutes. 3Turn on the power To turn on the power, press and hold the power button until the power LED lights blue. To turn off the power, press and hold the power button until the power LED turns off. Power/link LED Mute on/off OFF Forward/
Forward/
backward Charging LED DC jack Power button Volume +/-
Battery low LED Blue LED power is on Blue ashing LED connected to device Red LED battery is charging, turns off when charged Red ashing LED battery is low, recharge before LED turns off 4Pair with headset or audio dongle The Bluetooth Headset can be used with a Bluetooth A/V Transmitter or Bluetooth Audio Dongle. On rst use, the devices must be paired. To pair the devices. 1. Connect your transmitter to an audio device. 2. Turn on the power on your Bluetooth Headset. 3. Turn on the power on the transmitter. 5Wait for devices to connect The devices connect (pair) after 90 seconds. 7Troubleshooting If the Bluetooth Headset does not work, try the following:
- Ensure connecting devices are charged
- Turn off all devices and then turn them on in the order shown in this guide
- Ensure devices are within the 10-meter range 90 seconds
6Using with your mobile phone The Bluetooth Headset can be used with a Bluetooth-enabled mobile phone. To pair with your phone 1. Enable Bluetooth on your phone (refer to the phones user manual). 2. Turn on the headset. 3. In the phones Bluetooth menu, search for devices. 4. Select Stereo Headset. 5. Enter the passcode 0000. Answering calls To answer a call, push the power button. To end a call, push the power button for three seconds. 8Speci cations Standards Frequency Band Tx Power Rx Sensitivity Distance Audio Streaming Format Audio Frequency Range Audio S/N Audio THD Audio Output Power Power supply Physical Speci cation:
Environmental Range:
Bluetooth speci cation V1.2 compliant. Bluetooth A2DP pro le (AV Pro le) Bluetooth AVRCP pro le Headset and Hand free Power save mode (power sleep mode). 2402 ~ 2480 MHz 0.25 ~ 2.5mW (Bluetooth Power Class II)
< -80dBm (BER 0.1%)
> 10m (open space) SBC 48.000 kHz 20Hz ~ 22 kHz
> 85dB
< -83dB
> 20mWrms Supply by integrated rechargeable battery cell. Music plays : > 5hrs. Dimension: 180x140x60(max), 98x72x75(min) Weight: 62 gm Operating temperature:-10 ~ +50 degrees centigrade Humidity: Relative humidity 0 ~ 95%
Serial number & Firmware version:
the in accordance with Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.